Search Documents

By Hemingway J, Read T. A, Anderson V. G

IN the determination of very small amounts of lead, the usual analytical methods are far from being satisfactory. Small amounts of lead may be present in the reagents empioyed, and it is customary to run a blank experiment to correct the error arising in this way. When the correction is of small magnitude compared with the amount of lead in the sample, this procedure may be adopted; but when very small amounts of lead are being determined it may happen that the lead found in the blank is as much, or even more, than the lead actually present in the sample, and the analysis has to be rejected. Moreover, the blank experiment cannot check errors which are not common to the blank and the analysis itself eg, the apparatus used in the parallel experiments, etc. It seemed to be desirable, tl;l.erefore, to make an investigation of the problem to ascertain, as far as possible, the nature of the errors arising from the introduction or loss of lead during the analysis, and how far these could be eliminated or corrected for; also, to determine the limits of accuracy of the improved method and the minimum amount of lead that could be reliably estimated.In the investigation, reliability and sensitiveness were regarded as essential features. Speed of operation, on the other hand, was considered of less importance. The amounts of lead dealt with being usually less than 1 mg, there is no alternative to the use of a colorimetric method. The latter, depending as it does upon the development of a brown coloration when ammonium sulphide is added to a very dilute -solution of a lead salt, is far from being a characteristic test for lead. Indeed, it is well known that the salts of most of the commonly occurring metals interfere with this test. Hence it is of vital importance that the lead should be isolated in the form of a pure compound possessing quite definite and characteristic properties before the colorimetric estimation is proceeded with...

Jan 1, 1921

The treatment meIhods selected for the concentrator at Cobar Mines Pty. Ltd. called for a high degree of automatic control of both the grinding and flotation sections.The resulting concentrator layout includes a central control room overlooking both grinding and flotation sections. The control room houses process recorders, controllers, and indicators. together with motor stopstart stations and alarms.Plant instrumentation includes load cells and variable speed hydraulic drive feeders for feed-rate control of autogenous mills, together with nuclear density gauges, differential flow transmitters, and pneumatic control valves for water and pulp density control.Flotation cell pulp levels are controlled by floats and pneumatic actuators; flotation reagent controls include magnetic flowmeters and time-operated solenoid valves.

Jan 1, 1969

By Morris P. H

A trial embankment was constructed using coarse coal mine reject on a deposit of crusted coal mine tailings at New Hope Colliery, located in the Bundamba District of the West Moreton Coalfields in South East Queensland, Australia. The purpose of the trial embankment was to assess the load carrying capacity and settlement behaviour of the crusted tailings, including an assessment of strength gain in the tailings under the influence of the fill. Prior to construction of the trial embankment, a site investigation of the tailings deposit was carried out. This comprised vane shear strength testing, together with disturbed sampling and undisturbed block sampling for the purposes of laboratory testing. Following the site investigation, settlement plates and standpipes were installed at various depths and locations within the tailings in the vicinity of the proposed embankment. The instrumentation enabled the magnitudes and distributions of settlement and pore pressure within the tailings to be determined during and following construction of the embankment. The embankment was constructed using coarse reject in three equal lifts to a height of 3.0 m. The tailings sustained a maximum settlement under the weight of the fill of 290 mm, representing about 4.2 ii of the average initial thickness of the tailings and a loss of embankment height of about 9.7 %. By the end of the monitoring period the strength of the softer tailings underlying therust had roughly doubled under the influence of tha cmbarikment

Jan 1, 1990

By K L. Silversides

Shales form distinctive peaks in natural gamma downhole logs, which are used to manually identify the location of ore boundaries. These shales form important lithology markers that can potentially be automatically identified using Gaussian processes. This approach is trialled using data from a typical iron ore mine in Western Australia which contains the Marra Mamba sequence of the Hamersley province.The method uses Gaussian processes (GPs) with a single length scale squared exponential covariance function. A library of 8 m sections, where natural gamma measurements were taken at 10 cm intervals down the hole, was used to train the GP model. This library was iteratively improved and was tested using natural gamma logs that were not included in the library. Areas that were misclassified or were not clearly classifi ed were added to the library. The new library was then used to train the model and improve the results. The trials used a double gamma peak from the NS3 and NS4 shales at the boundary between the Newman 1 and Newman 2 ore zonesin the Newman member and the AS1 and AS2 shales at the base of the West Angelas member. The results show that both boundaries can be identifi ed with an accuracy of over 99 per cent. The classification has the highest accuracy on undeformed shales. This method provides a fast, accurate and objective identifi cation of shale and ore boundaries and can potentially replace the current manual detection.

Jul 11, 2011

By L Soares, W T. Hennies, F Fujimura

The engineering geological mapping of Metropolitan Area of Jopo Pessoa in the littoral zone of the Parafba State, northeast of Brazil, made possible the ambient characterisation for space using and its implications on the environmental resources. This region comes lately denoting an accented industrial growth and this work would help future projects of urban planning, distinguished by quick ground occupations for residential, industrial installations, farming, beyond mineral extractions. The mineral sector supplies material and substance demanded by industry and civil constructions, like as clay deposits, sands, calcareous rocks and mineral water. Many companies working there do not have the permission or inspection of ambient agencies for planned extractions of mineral resources. The consequences of this activity pass for the low profit of the reserves, bad uses of the sources, ground degradation, vegetation suppressions and physical impacts on landscapes, beyond noises and vibrations. These activities have causing accelerated alterations and transformations in the environment, compromising the sustainable development. It thus becomes clear that urgent solutions must be find to solve the problems with human interferences by closer inspection and management for disciplined use of its natural resources.

Jan 1, 2003

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

By L D. Redden, M G. Nelson

Mechanical flotation machine design is typically based on hydrodynamic analysis, with scale-up calculated by geometric proportionality. End users often specify and purchase machines on the basis of retention time, characterised by the æ$/m3Æ approach; they may also consider the manufacturerÆs installed base. In some applications, end users also consider specific energy and the impact of energy consumption on operational costs. In other cases, a decision may be based on machine type (forced-air versus self-aspirating) and perceived metallurgical or operational advantages of one machine type over the other. With regard to metallurgical performance efficient bubble-particle contact is very important and is primarily influenced by two factors:the concentration and size distribution of bubbles in the machineÆs contact zone (the volume enclosed by the disperser); and the number of times that slurry is pumped through the contact zone. The second factor is a function of the machineÆs pumping rate and its retention time. Field data show that pumping efficiency is independent of aeration rate. In this paper, a new dimensionless number for the characterisation of flotation efficiency is presented. The contact frequency number (CFN) is defined as the number of times a given volume of slurry passes through a machineÆs active contact region, and is given by: CFN Qp/Qf, where:Qpis the pumping rate through the contact regionQfis the volumetric feed rate to the machine

Jan 1, 2005

This paper attempts to put into perspective the implications of the legal disclosure requirements for promoters and consultants when making statements concerning ore resources and reserves. The need to take account of non-technical as well as technical factors is highlighted.

Jan 1, 1987

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

Response of a mineral to anionic and cationic flotation reagentsvaries with the nature of the mineral and the particle size. A ruleis deduced for the selection of the correct type of reagent, which leads to a simple method of testing ores to determine the possibility of separating the constituents by flotation.

Jan 1, 1963

Portable crushing at Duval Corporation's Sierrita open pit mine has proven both the economics and operability of large, hardrock, portable systems. In-house expertise was utilized to create a system incorporating both operational and maintenance features requested by operating personnel. The monitor/control system involves over 400 channels of information and is based on a DEC 1SI 11/2 microprocessor communicating with seven microprocessor-based data acquisition systems over a 4-wire, multidrop link. The year and one-half successful operation affirms the design philosophy and the hardware/software implementation.

Jan 1, 1985

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982

By G, F Beach, D Jazzini, R Rounsley

Over the past 20 years within Australia, there have been a number of incidents at mine sites where ammonium nitrate-based explosives have reacted with certain rock types containing sulfide minerals. These rocks have commonly been referred to as æreactive groundÆ. These reactions have frequently led to fires (particularly in ground susceptible to spontaneous combustion) or premature detonation of the ammonium nitrate-based explosives. Clearly, this introduces an element of risk when using ammonium nitrate-based explosives in these areas. Dyno Nobel has been proactive in developing ammonium nitrate-based explosive products that can be used in these types of æreactive groundÆ environments that minimise the risk of premature detonations occurring. A system for assessing æreactivityÆ of sulfide containing rocks has been developed that can be used in the field. Previous literature has been reviewed, identifying Differential Thermal Analysis (DTA) as the most common method for determining the æreactivityÆ of the ground. In the present investigation, DTA has been rejected as a suitable technique for determining ground reactivity, since it measures thermal reactions at higher temperatures over short time periods, conditions that are unlike those in the field. For example, ground at ambient temperature has been found to react with ammonium nitrate-based explosives over long time periods, reactions that are unable to be evaluated using DTA. Other more suitable techniques have been developed to monitor rock conditions that can be measured in the field and give a good indication of potential ground æreactivityÆ with ammonium nitrate-based explosives. Dyno Nobel is currently investigating the reaction mechanisms of spontaneous combustion in reactive ground, the decomposition mechanisms of ammonium nitrate and the role of inhibitors in ammonium nitrate-based explosives. Once complete, this fundamental research will lead to the further development of even lower risk ammonium nitrate-based explosive products for use in æreactive groundsÆ in a variety of mine environments.

Jan 1, 2003

By Hegedus M

The Hydrogeological Survay of the bauxite mines in Hungary was establisned 30 years ago. The goal of the HS has been to collect the all available date needed to solve the hydrogeological problems of bauxite mines. The results of activity of the HS have been summarized in the annual reports-. This report is going to present a few methods to evaluate the hydrogeological properties of fissured, karstic rock ie. the evaluation of drilling mud losses, the statistics of core samples evaluated by a special computer program for calculation the porosity and permeability of the rocks. An experimental injection test is presented together with the development of a new portable instrument to get signes of the water table change during the injection test in every two second. It can be proved that the flow around the well may be a transient one if the yield of the injection exceeds a definite one (Figure 2.). It was observed that the permeability calculated from the pumping test date may be 1.2-1.6 time higher than it coming from the injection test. A practical example is presented also how to use the results of the HS for designing the dewatering of a new mine together with an analogous computer model to forecast the yield expectable for making the drift tunnel. A suggestion based on the hydrogeological feature has been done for the dewatering without using electric energy (see Figure 3.-6.).

Jan 1, 1988

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

Sizing is fundamental technology for each step of ironmaking process. The progress of sizing technology has greatly contributed to the development of ironmaking technology. As the purposes of ironmaking operations diversified particularly since the oil crisis of 1973, the sizing technology made new advance- ment, as represented by pulverization of ser- pentine, dezincification and classification of secondary blast furnace dust, pulverized coal injection, size-segregated sinter charging and a coal preparation control process. These techniques are mostly characterized by the fine grinding of a given type of mineral or coal to heighten the degree of reaction con- trol. This trend is expected to continue Further.

Jan 1, 1984

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By Chavant G, Begis D, Gunther J

To study the ventilation of a mine (improve on the existing situation, examine extension projects) the calculation program used must take into account all the resistance values in the branches of the network. These resistance values are generally determined by measurements, which are accurate to a greater or lesser extent. In order to arrive by calculation at the flowrates measured :n the mine at a given moment, the resistance values have tto be adjusted experimentally. This manual operation is lengthy and delicate.

Jan 1, 1988

By H Kundapen, J J, C Rumble, S Miller

This paper describes measures taken by Ok Tedi Mining Limited (OTML) to minimise the risk of acid rock drainage (ARD) resulting from mining operations at its Mt Fubilan porphyry copper-gold mine in the remote Star Mountains of Papua New Guinea. The risk of acid generation and metal leaching as a result of oxidation of these sulfidic deposits has long been recognised by OTML. In 1998, OTML instigated the ARD Management Program to fully evaluate these risks and to formulate, if necessary, trial and implement appropriate management strategies. In implementing the ARD Management Program, OTML has adopted a risk management approach consisting of five stages: risk identification, risk analysis, risk assessment, risk treatment, and review and monitor. Significant progress has been made in relation to risk identification, analysis and assessment. The work currently underway to put in place a comprehensive risk treatment and review process will ultimately determine the success or otherwise of this approach.

Jan 1, 2003