Search Documents

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

By De Carvalho J

The average installed refrigeration capacity on South African gold mines has increased by about eighteen per cent annually for the past 15 years; both the number of installations and their duties have increased. One consequence of these large refrigeration installations is that careful attention must be paid to the system for distributing cold water. In these distribution systems, devices which minimize the temperature rise of the water delivered to the underground workings and which also reduce the pumping requirements for returning the water back to surface are used. In this paper the suitability of these various devices are examined and with the aid of a specially developed computer program their optimum operating conditions are determined. In addition the optimum combination of surface and underground refrigeration plants is examined for a hypothetical mine at various depths and the importance of pump efficiency on total distribution costs is discussed.

Jan 1, 1988

The large rotary blast hole drills for hole sizes of 250 to 375 mm in diameter have been utilized by large open pit metal and coal mines for production drilling all over the world. The design of such rotary drills is in most cases about two decades old and it has not been done much in order to apply a modern technology on rotary drilling. The most modern large rotary drill, Tamrock RI 10, consists of an advantageous rotary head with a squirrel cage AC motor controlled by a frequency converter, a beneficial mast structure with a possibility for inclined drilling, hydraulic driven, independent crawlers, and a modern ergonomic cabin to provide a comfortable working condition for the oper- ator. Several automatic features are available as options. The rig has been designed to be operated by one man only. With this modern rig the produc- tion rate can be increased and production cost kept on a low level.

Jan 1, 1989

By Borshoff J, Coles R

The Rum Jungle Uranium Province is lo cated on the western margin of the Pine Creek Geosyncline approximately 60km south of Darwin. Uranium was discovered in the Embayment area (Whites Deposit) in 1949, spurring active ex- ploration and leading to the discovery of the Rum Jungle Creek South Deposit in 1959. With the discovery of the Alligator Rivers Uranium Field, new criteria in the understanding of the controls for mineralization sparked a re- surgence of exploration activities in the Rum Jungle area. Uranerz Australia Pty. Ltd. (UAL) commenced exploration in the area in the late 1970's in joint venture and in its own right. Two domal Archaean granitic complexes, the Rum Jungle and Waterhouse Complexes, domi- nate the area. They are unconformably mantled by Lower Proterozoic sediments metamorphosed to middle to upper greenschist grade. The Lower Proterozoic sediments are unconformably over- lain by remnant blocks of Carpentarian sand- stone, generally preserved in downfaulted blocks. Over a six year period extensive geolo- gical, geochemical and geophysical programs were conducted to reinvestigate previous target areas and locate new prospective zones. Exten- sive shallow bedrock drilling showed that lo- cally the stratigraphic succession is quite variable and cannot always be divided into an ordered succession for correlation with groups and formations established by the Bureau of Mineral Resources (BMR). Deformational events resulting in intraformational recumbent folding and overthrusting also account for repetition of certain lithotypes.

Jan 1, 1984

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981

The segment of the Upper Cenozoic volcanic chain (CVZ) located on the western border of South America (16-28¦S lat.) is constituted by an association of strato- volcanoes and ignimbrite sheets, with high K calco-alkaline affinities. Strata-bound volcanoes, mainly of andesitic and dacitic composition, present along the whole chain, and various hydrothermal alteration zones, on the slopes and in the cores of eroded volcanic structures. Some of these altera- tion zones bear epithermal precious metal ores and sulphur deposits, which at present are being exploited. The studied Salar de Gorbea area, located in the Andes of northern Chile (25-26¦S lat.) contains a numer- ous group of Miocene to Quaternary stratovolcanoes, with advanced argillic and extreme silicification hydrothermal alteration in their cores and on their slopes, favoring the formation of great volumes of alunite within altered zones and sulphur deposits in the higher parts of the volcanic edifices. Simultaneously, siliceous hydrothermal breccia of the phreato-magmatic type, with evidences of hydromag- matic explosions are recognizable, allowing, in some cases, the ascent towards the surface of rock fragments belonging to the Paleozoic pre volcanic basement. Radiometric ages obtained in some of the hydro- thermal alteration zones (K-Ar in alunite) are slighty young- er than the unaltered rocks which constitute the strato- volcano. Trace element (Hg, As, Sb, S, Au, Ag, Cu, Pb, Zn, Mo) patterns in orientative rock samplings show that the studied alterations zones correspond to high sectors of the cpithermal system, without evidences of metallic minerali- zation on surface. The weak erosive action due to the ex- tremely and climatic conditions in this segment of the Andes, has not allowed the cropping out of deeper areas of the hydrothermal alteration zones, in contrast to other Miocene more eroded volcanic edifices and Miocene vol- canic terranes of the Andean Range.

Jan 1, 1987

By Eddy B. W, Washusen J. A, Wulff R. T

The State Electricity Commission of Victoria (SECV) has been con- tinuously involved in the extraction of brown coal from open cut mines in Victoria's Latrobe Valley for over 60 years, but have not completed a major mine. Detailed consideration for rehabilitation at this stage has only been able to be given to overburden disposal areas. Increasing interest in rehabilitation in the 1980's led the SECV to review its existing policies and practices and to embark in 1985 on a public consultation process to establish an agreed and accepted policy. This was extended in 1986 to the consultation process for the rehabilitation planning for the Mor- well Open Cut External Overburden Dump. This paper covers the con- sultative process developed and the lessons learned by the participants.

Jan 1, 1989

By Baafi EY, Sun Y, Tague I

Field trials at three New South Wales and one Queensland coal mines were carried out to gather data on oxygen "run out" times of Self-Contained Self Rescuers (SCSRs), time taken to escape from the mine, distances travelled and the average heart rate of subjects wearing SCSRs. The study has led to a method of predicting the duration of oxygen supply from a SCSR as a function of the wearer's body weight, physical fitness and the prevailing environmental conditions. Escapeway design, planning for emergencies, familiarity with SCSRs and experiential escape training are critical to control panic and maximise the likelihood of survival of a person attempting to escape in an emergency involving fire or explosion.

Jan 1, 1998

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

An effective production control system should maximise recovery of economic material from the resource. To do this, internal waste must be accurately delineated and efficiently removed. Achieving this is most difficult in low grade blocks just above and just below the cut off grade, where ore:waste separation follows assay or statistical, rather than geological boundaries. Difficulties arise from sampling errors, configuration of the economic mineralisation, and local variations in geology. Mine bench parameters and mining equipment size apply further constraints to the actual field separation of the ore from the waste. At BCL, management of the resource starts with an effective orebody model for planning, scheduling and ore:waste prediction. Ore production from each mining location is reconciled with concentrator tonnage and grade, and the reconciled grades are compared with the planning orebody model to highlight any Differences.

Jan 1, 1986

By Else D

While the underground mining work environment may have processes and equipment considered unique, most of the broad issues likely to affect the occupational health and safety of employees are not. One such occupational health and safety issue that is common to the mining sector and most other industries is noise. Noise as an occupational health and safety issue is of national significance. Presently noise induced hearing loss costs Australia around $35 million per year on compensation claims experience alone. Noisy equipment and work environments are still being tolerated in parts of the mining industry as `part of the job'. Where work has been undertaken in noise management, considerable emphasis has been placed on either industrial hygiene monitoring programs or the provision of hearing protectors to miners working on or around noisy equipment.Opportunities for more cost-effective and long term methods for controlling noise exist. Ready to apply solutions to noise problems in the mining industry are available, but for many mining operators this information is often difficult to obtain. To overcome this problem, the SHARE program collects and distributes solutions to occupational health and safety problems. The program aims to help organisations to close the gap between what is known about solving health and safety problems and what is actually being applied at the shop floor level: Recent developments have incorporated the SHARE program concept into worksite hazard management projects that involve the participation of employee representatives, front line supervisors and engineering personnel. Besides providing workforce members with an increased understanding of hazard management skills, the SHARE in-house program results in the implementation and sharing of solutions to health and safety problems by the program participants.

Jan 1, 1992

Gunpowder Copper Limited processes 1,000 tonne/day of Mammoth ore in a conventional flot- ation concentrator. Run of mine ore is prepared for flotation by three stages of crushing and two stages of ball milling. The concentrate, in which the primary copper mineral is chalcocite, is solar dried and exported to Japan. The history of operation is summarised, and plant practice and metallurgical problems are discussed.

Jan 1, 1974

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

Rock bolting provides a supplement or alternative to conventional timber and steel supports. The tensile strength of the bolts lies within a range established by manufacturing quality control. Rock bolt testing determines the ability of the rock, anchor and individual bolt as an assembly to accept load. The.test is performed to the yield strength of the bolt or anchor and deflection is observed. The anchorage index, inches deflection per 1000 lb load increment, is a measure of anchorage quality. This allows comparison with anchorages under ideal conditions. It also permits comparative assessment of roof bolt anchors in a particular environment.

Jan 1, 1971

The Beaconsfield Gold Mine within the township of Beaconsfield in northern Tasmania has been established in recent years to exploit a known resource in the Tasmania Reef which was mined to a depth of 450 m below surface between 1877 and 1914 yielding 850 000 ounces of gold. Activity at Beaconsfield over the past 30 years has involved drilling to assess the resource and rehabilitation of the top 100 m of the Hart Shaft that had collapsed since the original closure. More recently the mine has been dewatered to the 375 m Level and work is well advanced establishing infrastructure aimed at recommencing production during 1998 - 99. This paper reviews geotechnical studies undertaken to-date and provides a brief overview of some practical methods of analysing ground conditions. It pursues simple observation and analysis as a tool for assessing mine design and ground support options without recourse to extensive monitoring and measurement and avoids the use of elaborate models before the basics are understood.

Jan 1, 1997