Search Documents

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

By Nelson G

The construction and placement of tunnels by means of jacking is continually advancing. This paper presents an outline of the construction of a major highway tunnel placed by a combination of mining and progressive placement by hydraulic jacking of precast units. Features of the project were the relatively shallow ground cover between rail and road routes over the tunnelling and jacking operations and also the weight of tunnel sections to be moved into position.

Jan 1, 1993

By R M. Hough, G Duclaux, M A. Pearce, M F. Gazley

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Microcharacterisation, such as that described in this paper, provides understanding of a mineral system at multiple scales, and understanding microscale variations is the key to understanding the large-scale variations in a mineral system. More than 50 high-grade lode samples from across Plutonic Gold Mine (Plutonic), Marymia Inlier, Western Australia were analysed by a variety of techniques, including micro X-ray fluorescence (µXRF) mapping, micro X-ray computed tomography (µCT), scanning electron microscopy (SEM), field emission gun SEM, electron back-scatter detector (EBSD), proton-induced X-ray emission microprobe and synchrotron XRF mapping. These data demonstrate that competency contrasts are the key to governing the location of Au mineralisation at Plutonic. Micro CT imaging of high-grade samples shows the Au filling in voids and pore-space in the rock, after having travelled along more permeable layers and already existing or reaction-induced pores formed during hydrothermal circulation. Using 3D visualisation, the Au is seen to form a connected network that appears undisturbed at the scale of the samples, and a high-grade Au deposition event was one of the last events to affect the rock. This interpretation is supported by SEM analyses on high-grade samples that reveal calc-silicate (epidote-clinozoisite) alteration that is not present in lower Au grade samples, which are typically dominated by potassic alteration, and that sulfides are typically less abundant close to the Au. The replacement of biotite by chlorite is an alteration associated with the high-grade Au-mineralising fluid. Gold is coarsest where Au particles are located on the margins of minerals, typically sulfide and quartz grains, suggesting the importance of rheological contrast at the microscale. Furthermore, EBSD data reveals that Au is undeformed and overprints peak metamorphic and retrograde minerals. Data confirm recent deposit-scale observations, suggesting that deposition of high-grade, visible Au was related to a hydrothermal fluid circulation event late in the geological history of Plutonic.CITATION:Gazley, M F, Duclaux, G, Fisher, L A, Hough, R M and Pearce, M A, 2015. High-resolution characterisation of gold mineralisation at Plutonic Gold Mine, Western Australia – evidence for the late-stage deposition of high-grade gold , in Proceedings PACRIM 2015 Congress, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Ho E

Analyses of several nickel mattes from around the world show a significant variation in their copper content. Typically, matte contains an alloy, heazlewoodite and a copper sulphide phase. The various commercial methods of processing these mattes are reviewed and some of the fundamental factors which determine the choice of leaching system are discussed. Electrochemical studies on pure heazlewoodite and millerite in sulphate and chloride media are compared which show that nickel sulphides react via a series of nickel deficient sulphides and exhibit passivation as nickel is removed. Differences in the electrochemical behaviour of nickel sulphides in chloride media are attributed to greater crystallinity of sulphur and less formation of'NiS2. The electrochemistry of mattes differs because of the presence of alloy and copper. Copper in the matte modifies the potential for alloy dissolution and the rate of anodic dissolution of nickel. At elevated temperatures, Cu(II) in solution exchanges with NiS and completes the leaching of nickel at relatively low potentials without significant oxidation of sulphur to sulphate. It is concluded that there are fundamental advantages to leaching nickel matte in chloride media using Cu(II)/Clz as the oxidant.

Jan 1, 1996

Two significant TBM boreability predic- tion models are outlined. Predicted advance rates are compared with actual advance rates taken from twenty case histories. The results show that a simple low cost method that uses one machine parameter and one rock parameter compares very favourably with a high cost sophisticated method which also includes information regarding discontinuities in the rock mass. The effect of rock texture on drillability is also examined. A method of quantifying rock texture has been developed and is outlined. Experimental results show that the developed TEXTURE COEFFICIENT returns highly statisti- cally significant correlations with drilla- bility data in a wide range of rock types.

Jan 1, 1987

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By Williams RC

Overlying the coal deposits of the Sydney Basin are several lakes and other bodies of water. These include the Pacific Ocean, Lake Macquarie, the Tuggerah Lakes and the stored waters of the dams of the New South Wales Metropolitan Water Sewerage and Drainage Board. The coal beneath these bodies of water amounts to hundreds of millions of tons. Colliery workings have approached these areas of water and in some instances first 1"orkings of bord and pillar have taken place oi_eshh the water. he problem which now faces mine manage- and other interested authorities involves the determination of the maximum ;mount of coal which can be safely extracted from beneath the water. There are many factors to be considered including the depth of cover, seam thickness, geological details and strata movements.

Jan 1, 1972

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

The accurate determination of trace level gold in ores, metallurgical samples and process solutions is required because of the value of gold, the efficiency of the cyanide leach process and because of the high gold recovery from these cyanide solutions. It is thus necessary to routinely analyse geological and metallurgical samples with gold concentrations of 3 g tonne (ug g- 1ppm) and process solutions with a gold concentration of 0.01 mgL 1 (ppm) preferably with sufficient accuracy to quote at least two significant figures. Several techniques have been reviewed for their suitability for the routine gold analysis of these samples which also contain signif- icant concentrations of other ions. The classic fire assay technique has achieved the respect and confidence of mining personnel because of the results achieved by very experienced assayers. Other extraction and concentration techniques have now been shown to be equally effective. The use of instrumental analytical techniques particularly atomic absorption spectrometry have shown that cheaper procedures, which are as reliable, are now available to gold producers for the routine analysis required to maintain an efficient gold recovery process.

Jan 1, 1982

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By Reeves T. J, Hansen J. Y

Dense medium cyclone theory, supported by extensive experimental and plant-scale evidence, demonstrates that medium rheology (stability and viscosity) substantially affects cyclone performance in mineral applications.Two instruments have therefore been developed to allow medium stability and viscosity to be-monitored in the plant environment. The instruments are described, and examples are given of their application in full-scale plants.

Jan 1, 1989

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998