Search Documents

By M G. Shaw, M A. Rhamdhani, S P. Singh, A R. Duffy, B Eisenbart, A K. Shukla, G A. Brooks

The field of astrometallurgy is a growing area of study. Metal production on the Moon is likely to begin in less than a decade as major space agencies such as NASA (National Aeronautics and Space Administration) and CNSA (China National Space Administration) are preparing to construct permanent lunar bases. The utilisation of regolith to generate oxygen and metals is expected to be important in the development of a sustainable lunar habitat. This paper provides an overview of potential metallurgical processing methods for lunar conditions, emphasising the impact of lunar factors on slag chemistry. The interaction between regolith and the extracted metals, as well as their impact on slag composition and refractory performance, are critical considerations in metal production on the lunar surface. The initial research on lunar metallurgical technologies is focused on oxygen extraction and Fe-Si alloys are reported as the by-products of these processes. This paper delves into the fundamental thermodynamics associated with the carbothermic reduction of lunar regolith. Thermodynamic analysis using the FactSage™ ver 8.2 software package indicates that the Fe-Si alloy can be produced as a metallic product from the lunar regolith at temperatures ranging from 1400°C to 1600°C under terrestrial conditions. However, under ultra-high vacuum conditions (3 × 10-15 bar) on the Moon, the required operating temperature for producing ferrosilicon would be significantly reduced. Thermodynamic modelling results indicate that under lunar vacuum conditions, Fe-Si alloys only exist as solid phases at lower temperatures below 650°C. At higher temperatures, both Fe and Si are expected to be present in the gas phase. In this work, the carbothermic reduction of the Lunar Mare Simulant (LMS-1) is conducted under terrestrial conditions. The findings indicate that the process can readily yield Fe-Si alloys with 7–10 wt per cent Si at 1600°C. Additionally, energy dispersive spectroscopy (EDS) analysis of the resulting Fe-Si alloy indicates the presence of phosphorus up to 1 wt per cent.

Aug 21, 2024

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By Muldoon T

Water sprays on mining machines are generally put there to reduce dust; however, research by the Bureau of Mines and others has shown that considerable airflows may also be generated by these sprays. This recognition of water spray-gen- erated air movement led to the "Spray-Fan" - a continuous miner auxiliary ventilation system which was shown to reduce methane peaks by a factor of 15. Recent successes and failures of the Spray Fan are reviewed. More recently, the same principles were used in the design of the "Shearer- Clearer" for reducing dust at longwall shearer operators. The original design was successful; however, a new design is now available which is more practical to install and does a much better job of holding the dust against the face downwind of the shearer. The latest research objective is to eliminate the negative impact of spray- generated air turbulence on continuous miner dust control. Most coal faces in the USA are ventilated in the exhaust mode using "line curtain", and the forward airflow on the side of the heading opposite the curtain is inevitably weak. Air turbulence generated by sprays which are incorrectly located and/or operated at excessive pressures can cause roll back - in which the dust cloud at the face is forced unwind against the ventilation and spreads over the miner cnerator. The general approach to reducing "roll back." is reviewed and art anti-roll back water spray system is presented.

Jan 1, 1983

Coal seam methane (CSM) is an æunconventionalÆ gas resource that is becoming an important energy resource for Australia, especially along the eastern seaboard. It has been conventionally believed that methane in high rank coals was exclusively derived from thermocatalytic processes during decomposition of coal at elevated temperatures. However, recent re-interpretations of gas composition and isotope data have indicated that microbial methane generation may be one of the main processes responsible for the accumulation of commercially producible methane in some coals. In low rank (æbrownÆ and sub-bituminous) coals, methane (CH4) is mainly generated by microbial activity at low temperatures. The amount of this biogenic gas generated and accumulated in low rank coals depends largely on the rate of burial and depth. Most low rank coals are æunder-saturatedÆ with respect to their maximum gas sorption capacity. In contrast, high rank coals may be highly saturated due to extensive gas generation from both thermogenic and secondary biogenic processes. However, in basins where secondary biogenic gases have not replenished the thermogenic gas lost during basin uplift, the coals will be æunder-saturatedÆ. In many basins around the world, high CSM producing zones appear to contain secondary biogenic CH4 generated by microbes transported in meteoric water recharge through permeable coal seams. Biogenic CH4 generation requires the activity of a consortium of anaerobic respiring microorganisms, fermentative bacteria and acetogenic bacteria to break down complex organic molecules to simpler molecules having one or two carbon atoms, which enables methanogenic archaea to generate CH4. The two main methanogenic pathways in the generation of secondary biogenic gas from coal are aceticlastic reaction and carbon dioxide (CO2) reduction. In eastern Australian coals CO2 reduction appears to be the main process. The types of microbes that are directly involved in these processes are unknown because they have not yet been isolated from the coal seams. The CSIRO is currently investigating the processes of biogenic gas generation in Australian coals. Potential may exist to introduce appropriate microbes into deep coal seams to enhance methane saturation levels, gas sorption capacities and permeabilities.

Jan 1, 2004

By Maidl B

A tunnel operations analyser is a new high technol- ogy instrument for use in underground work. By remotely sensing the acoustic emissions from operating machines and processes in a tunnel or shaft and by applying sophis- ticated computer processing to them individual process cycles and other detailed information about the operating processes can be collected. Detailed analyses and dissec- tions of the work in progress can be made and a variety of action oriented management reports produced. The pro- cess is fully automatic. Results of applying this device to two full scale tunnel projects are presented. The hardware and software that comprise the instrument are discussed in detail. Processes by which this device can be used to sub- stantially reduce tunnel costs are presented. It is concluded that this type of technology has great potential.

Jan 1, 1987

By Lindner E, Bosio M

South Australian coals are all low in rank and generally poor in quality, with difficult combustion characteristics. This circumstance makes the selection of a fuel source for future power generation difficult, requiring careful study and detailed analysis of the various alternatives. Combustion characteristics can have a significant effect on plant design and costs, and need early attention in any exploration and evaluation programme. The physical location of the deposits, often remote from established infrastructure and centres of population, is also a major factor in the ultimate cost of power at the poirl use.

Jan 1, 1977

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

By Whincup P

Hilton deposit comprises en-echelon silver-lead-zinc orebodies with reserves in excess of 50 million tonnes. The host rock to the ore is a dolomitic and pyritic shale/siltstone which dips steeply west. The shale/siltstone is deeply leached and porous, particularly over the Ore Zone where the depth of leaching continues down to 440 m below surface, and constitutes an extensive permeable aquifer system containing a large volume of saline acidic groundwater. Initial production commenced at Hilton in 1987 well below the aquifer. A dedicated dewatering and monitoring programme is in place to ensure security of stoping operations and allow extraction of ore close to the leached zone in future years. Dewatering is undertaken from controlled bores from underground sites. Mine groundwater discharge is presently at the rate of 4000 kl/day with plans to increase to 8000 kl/day. An additional 2000 kl/day of fill and service water and water from secondary aquifers is also pumped from the mine daily. Although recharge rate to the aquifer is minimal, studies indicate that due to the size of the aquifer and future extensions to mine development, dewatering will be a life of mine activity. The investigations which have been undertaken to determine optimum dewatering techniques and schedules are described. These include production bore tests, mine planning constraints and computer aquifer modelling. Gravity geophysical techniques have been successful in delineating the lateral and vertical disposition of the aquifer. The mine dewatering schedule, whose principal component is underground mine drainage, is also outlined.

Jan 1, 1988

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

By Lawless JV

Recent exploration for gold on the Pacific Rim has utilised similarities between active hydrothermal systems and epithermal gold deposits. The major control over formation of such deposits is the hydrology of the ore-depositing hydrothermal system, which varies depending upon its geologic setting.

Jan 1, 1987

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By U Rehm

The biggest hard rock double-shield tunnel boring machine (TBM) in the world, with a diameter of 12.4 m, is currently excavating the North-South Bypass, which includes a crossing under the Brisbane River, Brisbane, Australia, to relieve the often congested road traffic in the city centre. Ten years ago a 10.7 m Mixshield giant helped to handle the Olympic Games in Sydney linking the airport with the city centre for an improved transportation of fascinated visitors. In Shanghai, currently the biggest TBM in the world with 15.43 m diameter presents excellent performance rates; and in Paris a convertible Mixshield could be quickly changed from earth pressure balanced (EPB) to slurry type in order to handle the very heterogeneous ground conditions. In Madrid a 15.2 m EPB giant finished its tunnel job four months ahead of schedule. Large-scale TBMs have proved their economic and innovative potential to create the current and future underground architecture of mega-cities. TBM technology has made further large innovative steps in the last decade. State-of-the-art is a TBM for very heterogeneous ground conditions comprising hard and soft rock with additional high groundwater pressure. The machine concept is adapted to the various ground conditions and allows for a quick and flexible application. Ground treatment by means of additives developed to a helpful tool in this connection. To meet the special challenges of urban tunnel projects of nowadays it is of very high importance, beside applying highest developed technology of TBM, to have a comprehensive technical support during the project phase and to develop positive relationships between all participants of the project which last longer than only for one project.

Jan 1, 2008

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

By Chilman G. F, Lean P. J

The New Broken Hill Oonsolidated LImited (NBHC) concentrator was commissioned in 1952 and underwent a number of expansions over the next 25 years. In 1978, the decision was taken to expand further from 1.20 million tonne/yr to 1.43 million tonne/yr. This increase necessitated a substantial modification to an already over-taxed grinding circuit. The circuit consisted of rod mills, ball mills and rake classifiers. Plant data of grinding mill performance was obtained to develop mathematical models of individual units that could be combined to simulate total circuit performance in a number of configurations. The data provided further illustration of the validity of the perfect mixing model for relatively small increments of ball mill scale-up.

Jan 1, 1983

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993