Search Documents

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. The Zapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level. However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy.

Jan 1, 1995

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

By R Brake

The Enterprise Mine Project (EMP) is being developed by Mount IsaMines Limited as the future source of copper ore at the Mt Isa miningand processing complex. Environmental engineering is one of the majortechnical challenges facing the project because of the depth of theorebodies, high virgin rock temperatures and hot ambient surfacetemperatures in summer. This paper discusses the engineering principles adopted by EMP to manage the risks associated with working in these adverse thermal conditions.

Jan 1, 1998

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By J S. Laskowski

Froth flotation process requires the use of frothers. These important flotation agents are commonly characterised as either æselectiveÆ or æpowerfulÆ and are chosen following general guidelines and verification by laboratory and/or pilot plant tests. Fundamental properties of the flotation frothers have been extensively studied over the last few years. These studies have led to the development of standardised procedures to characterise frothers in terms of their ability to reduce bubble size and to increase foam stability. In this research project, the performance of five frothers in flotation of coal is evaluated and related to the fundamental properties of these agents. Since the recovery of water in the concentrate is closely related to the non-selective transport of solid particles by entrainment, the tested frothers are also assessed in terms of their ability to promote the transport of water towards the froth collection zone, both in absence and in presence of solids.

Jan 1, 2005

Problems associated with gas management become more significant as exploitation of coal reserves in the Bowen Basin in Australia becomes deeper. At Oaky North mine, relocation of production from one area of the mine to another with a higher gas content required the use of pre-drainage, post drainage and inertisation techniques to enable production activities to continue largely uninterrupted. Innovative surface to inseam drilling techniques were developed for pre-drainage of reserves close to mine workings and have proven to be largely successful. The gas management techniques adopted and specific experience gained are discussed in this paper.

Jan 1, 2005

By G D. Carman

White Rock is a reduced tungsten-tin skarn deposit near Rye Park, New South Wales. This abstract summarises the depositÆs mining and exploration history, and current exploration by Paradigm Metals Ltd targeting an economic resource at the deposit. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By E Widijanto, A Srikant

PT Freeport Indonesia operates a copper-gold mine located in the remote highlands of Papua, Indonesia, about 3500 km east of Jakarta. Currently, the district produces about 240 000 tonnes per day (tpd) of which about 45 000 tpd come from the DOZ Block Cave and the rest is mined from the Grasberg Open Pit. Over the next ten years, ore production from large block caves in the area is expected to reach about 200 000 tpd, replacing a large part of the production from the Grasberg Pit. Block cave mining alters the hydrological characteristics of the area being mined and when the cave expresses itself at the surface in the form of subsidence, it increases the entrapment area for surface water. Operating a large block cave mine in a region with an average annual rainfall of 5500 mm in steep mountainous terrain and complex geological and hydrological features presents a challenging scenario for dewatering or depressurisation of the area. The high rainfall infiltration and entrapment in stacked mines operating within an essentially single orebody, coupled with the presence of fine-grained and clayey material within the draw points of the block cave, creates mud rushes or wet muck spills, which can endanger the personnel and interrupt production. This paper outlines the problems caused by high water inflow into the DOZ Block Cave and the efforts undertaken to ensure the safety of the miners and continued achievement of desired production rates from underground mining in the district.

Jan 1, 2006

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

By I J. Holland

Located in North West Queensland, XstrataÆs Mount Isa Copper Operations (MICO) is one of the largest underground mines in Australia with annual production exceeding six million tonnes of ore with average copper grades of three per cent. As at 30 June 2006, the Ore Reserve inventory totalled 87 Mt, with annual diamond drilling planned at >40 000 m in order to convert existing resources and test and define exploration targets. The role of the geology department within MICO is to collect, interpret and communicate relevant geological information to ensure the optimal extraction of ore. Routine underground inspections across multiple ore sources are undertaken and the information derived is then distributed to a range of professionals, operational personnel and management. The information is a æreal-timeÆ geological view for the stakeholders. Ongoing data collection and interpretation has developed a strong geological input to all mine planning processes within MICO. This has created strong synergies between mine planning professionals and a throughput benefit has been seen all the way to the concentrator. The MICO geological framework also provides avenues for a geological focus away from short-term production requirements, and as a result significant orebody scale observations and patterns have been realised that have led to an increase in the accuracy of geological and resource models. This has provided practical benefits for short-term scheduling and production, whilst enabling the realisation of long-term benefits that have a strong potential to increase the volume and value of the MICO resource. This paper will discuss the various mine geology contributions at MICO and illustrate some examples where mine geological input from graduate level has added significant value to the MICO business.

Jan 1, 2007

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

By M E. Rakidjan

The DOZ underground mine at PT Freeport Indonesia is a copper and gold mine in Indonesia with current ore production of 42 000 tpd. Because of the mine expansion into the West DOZ more ventilation raises are needed to create a safe and healthy work place. All ventilation raises that connect the extraction levels to the underlying gallery exhaust drifts at DOZ are now developed using drop raise techniques. This paper describes the improvements undertaken to increase blasting efficiency, to decrease cost and reduce safety risks. This was achieved by using deck loading and presplitting, changing of stemming materials and prevention of excessive raise collar cratering (blow up).

Jan 1, 2005

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

Viking Holdings Ltd, a Todd Corporation company, is active in the mineral industry through operations, joint ventures and equity investments. Identification and management of risk is key to the success of the company. This paper discusses risk in general terms and in the context of Vikings activities. Reference is made to the current environment and the impact of risk and environment on profitability.

Jan 1, 1997

The control objectives and constraints for grinding circuits are ana- lysed, taking a single-stage ballmill-cyclone circuit as an example. The design of a hierarchical modular control system is described, for implemen- tation on modern microprocessor-based control systems. Product sizing measurement is identified as a problem area, and a new approach to product sizing inference, from on-line cyclone feed and overflow measure- ments, is presented. The procedure over-comes several practical difficulties of a previously proposed inferential method and is therefore expected to find application in more advanced grinding circuit control systems.

Jan 1, 1988