Search Documents

A Study on Process Mineralogy and Mineral Processing of Complex Carbon-Bearing Cu-Pb-Co-Ni Multi-Metal Sulfide Ore by Bulk Flotation

Sep 13, 2010

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

By C Ward, U Mueller

Compositional geostatistics is an approach developed to ensure that the constant sum constraint induced by geochemical iron ore analysis is respected in estimation and simulation. Jack-knifing and cross-validation were used within this framework to compare the results from ordinary cokriging of the additive log ratio (alr) variables with those from conventional ordinary cokriging. Two methods were used to back-transform the alr estimates: the crude additive generalised logistic back transformation and numerical integration via Gauss-Hermite quadrature. Previous work on a blasthole data set from a Yilgarn iron ore mine showed promising results, with the Gauss-Hermite quadrature method returning results comparable to ordinary cokriging from the point of view of bias, but superior in that the constant sum constraint imposed by geochemistry of the data was honoured. Other practitioners have noted that the linear interpolation of non-linear log ratio transformations will result in biased results, and that this bias can be masked in a (grade control) setting where the spatial density is high. To test this assertion, the methodology has been extended to successively lower spatial density data sets. The results and applicability to routine iron estimation are discussed.CITATION:Ward, C and Mueller, U, 2013. Compositions, log ratios and bias - from grade control to resource definition, in Proceedings Iron Ore 2013 , pp 313-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Fabjanczyk MW, Guy RJ, Tarrant GC

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992

By Harvey T, Kizil M, Bride J

Hydrogen sulphide (H2S) as a seam gas has occurred in several locations in the German Creek seam at Southern Colliery. This paper overviews the techniques developed to quantify the H2S content of the seam, overviews research into controlling and reducing H2S emissions from the seam, and details the procedures used to mine through the HZS zone in 702 longwall panel. Learning points from research and mining experience are reviewed for application in the next longwall block.

Jan 1, 1998

By burgess F, Manlapig E. V, Franzidis J. P

Bubble surface area flux, a parameter which is determined by bubble size and superficial gas velocity, has been identified as a criterion for flotation scale-up from a metallurgical point of view. Investigations at Hellyer, Scuddles and Mt Isa

Jan 1, 1997

By Kyle J. H, Browner R. E

The selective adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4* and Duolite A-7*, the neutral polymeric adsorbent, Amberlite XAD7*, and the strong base resins, PAZ-8 and IRA-400+ have been studied in both low and high salinity waters, and performance compared with activated carbon. The selectivity of the neutral polymeric adsorbent and activated carbon for gold decreased in highly saline water, while the selectivity of weak and strong base resins for gold increased in highly saline water. This supports the contention that the adsorption mechanism for neutral polymeric adsorbents and activated carbon is the same. Copyright

Jan 1, 1992

By Y Gu

Based on the mode of occurrence, gold is classified into three categories: microscopic gold, submicroscopic gold and surface-bound gold. Microscopic gold, or visible gold, refers to gold minerals in which Au occurs in a substantial amount, such as native gold and electrum. Submicroscopic gold, ie invisible gold, refers to gold contained in the structure of other minerals (mainly sulfides) in minor to trace amounts. Surface gold is the gold that was adsorbed onto the surface of other minerals during mineralisation and subsequent oxidation or metallurgical processing. Gold mineralogy has a significant impact on its extractive metallurgy. Gold process mineralogy helps address problems related to gold ore processing. It is widely used as a predictive and troubleshooting tool in gold ore processing, and provides useful information on process selection, flow sheet development, recovery improvement and reagent consumption optimisation. This paper will begin with the classification of gold ores, and will focus on gold mineralogy and how it impacts extractive metallurgy through case studies.

Jan 1, 2008

By G Showers, R Triglavcanin

The complexity of understanding the whole thickening process to achieve real performance improvements cannot be underestimated. The last significant change in feedwell design was more than 15 years ago with the introduction of self-dilution systems û firstly with OutotecÆs Autodil, followed by FLSmidthÆs E-Duc. Now, following many years of extensive in-house research, including close collaboration with AMIRA and the CSIRO, Outotec has launched the next generation Vane Feedwell. The Vane Feedwell has been globally patented and installed at various sites. This paper briefly outlines the feedwellÆs development using CFD modelling and its subsequent performance in a æreal lifeÆ site installation. Plant results of the first commercial Vane Feedwell, in a mineral sands application, are discussed. The Vane Feedwell was retrofitted so comparative data of pre- and post-installation is shown.

Jan 1, 2009

Mining is an intensive resource development industry, where operations are often of relatively short duration and can result in dramatic impacts on the natural environment during the operational period and for many years post mining. An integral component of all mining operations is water û through exploration, resource definition, mine development and operation, rehabilitation and the long-term post-mining land use. Water is a basic requirement in the provision of worker amenities, in drilling, as a means of dust suppression, as a medium for washing or processing the mine product, and as an aid in establishing vegetation on post-mining landforms. Water also plays an important role in mobilising environmental contaminants and is the primary medium for the transport of contaminants off the mine or processing site into the wider environment. It is for this second reason that the mining industry considers water management as a key component of mine management. Cost-effective water management relies on planning that incorporates a total mine system approach commencing prior to exploration and continuing through to rehabilitation and decommissioning. One of the primary considerations that will provide confidence to both government and community at the time of mine closure and lease relinquishment, will be the evidence that any water originating from, or passing through, the mine site is of a quality that will not have any negative impact on the surrounding environs into the future. The role of vegetation in stabilising disturbances to a landscape is well known, as is the recognition of vegetation being a fundamental component of the water cycle through the physiological processes resulting in the transfer of water back to the atmosphere through transpiration. In terms of water management at a mine site, the two crucial issues are the æquantityÆ and æqualityÆ of water that enters a receiving æoff-leaseÆ catchment. In terms of tolerances of the receiving environment, the total load of potential contaminants becomes critical, a reduction in which can be achieved through reduced volumes of water discharged, reduced chemical and physical concentrations of contaminants in that water, and ideally, both. This paper examines the potential role of vegetation in reducing the quantity of water released from a site, and secondly considers vegetation in the role of influencing the quality of that water.

Jan 1, 2003

By Wyborn L. A I, Idnurm M, Hinman M. C

Comparison of the Proterozoic Apparent Polar Wander Path (APWP) for Australia with the corresponding geology of northern Australia suggests that a number of discrete interplate tectonic events, manifested on the APWP as bends or inflections, may have controlled sedimentary basin evolution, ore fluid production and the timing of mineralisation. Similar features in the Phanerozoic APWP for the North American plate appear to correlate with major orogenic events, basin deformation, movement and 'entrapment' of hydrocarbons and minerals. Interplate tectonic events cause intraplate deformation which in turn controls the subsidence/uplift and sedimentation histories of the basins. Interplate events are thus responsible for creating, deforming and destroying sedimentary basins and the associated petroleum and mineral systems. The basins of northern Australia show remarkable similarities in the successions of volcanic and sedimentary deposits. Unconforrnities of regional or sometimes only local extent have been mapped between the major sedimentary sequences and it is predicted that interplate tectonic events corresponding to bends or inflections on the APWP directly reflect the processes that have produced these widespread unconformities. These processes are also likely to have controlled the geometry and character of the fluid migration pathways and hence the mineralising events. Palaeomagnetic studies of Proterozoic rocks in sedimentary basins provide a tool for predicting the timing of regional mineralisation events, particularly for low-temperature mineral systems. The techniques, when coupled with systematic regional basin analysis, using petroleum exploration techniques, may identify a number of new mineral 'plays' in northern Australia. Prominent inflections in the APWP occur at approximately 1700, 1670, 1650, 1600, 1540, and 1480 Ma. Each of these may be related to a regional compressional deformation, important mineralising event, or significant change in style and type of sedimentation. Most appear to be associated with magnetic overprints. Some of the inflections between 1400 and 540 Ma may also mark significant events in the evolution of Meso- and Neoproterozoic basins. Further work is required to correlate inflections in the APWP with alteration events in order to understand their regional significance.

Jan 1, 1994

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By J Benn, V Kuznetsov, G Timms, A Spain

Earthen covers are now widely used in the mining industry to control the generation rate and/or release rate of low quality drainage from piles of sulfidic minewastes. Covers are usually designed to reduce the water infiltration rate and in some cases may also reduce the oxygen flux to the underlying sulfides. Engineered covers have only been used since the 1980s, however, and there is very little field data on their performance in the longer term. This lack of information has implications for the degree of confidence that can be placed on the predictions of the environmental impacts of sulfidic minewastes, for the acceptance of close-out criteria by regulatory authorities and for the financial liability of the mining industry. Covers were placed on sulfidic waste rock dumps at the abandoned Rum Jungle uranium mine during 1984 - 1985. These covers were designed to reduce the water infiltration to less than five per cent of incident rainfall by both water shedding and storage-release mechanisms. Regular monitoring by the Australian Nuclear Science and Technology Organisation (ANSTO) demonstrated that the covers performed better than the design criterion for around ten years, but infiltration rates have subsequently increased. There is a 66 per cent probability that the infiltration rate now exceeds five per cent of incident rainfall. The cover on the largest pile, WhiteÆs heap, was sampled in pits dug at eight locations. Sampling was carried out at the end of the monsoonal wet season and again at the end of the ædryÆ season. This, together with laboratory testing, enabled cover performance to be assessed against five criteria: design, construction, cover material characteristics, physico-chemical characteristics and biological characteristics. We are of the opinion that the design of the cover was suitable to achieve the objectives of stability, water shedding, storage-release, and provision of a substrate for vegetation growth. Over most of the surface of the heap, the construction of the covers, drains and erosion prevention structures was in accordance with design specifications. However, several small and localised bare patches on the upper surface of WhiteÆs heap coincide with a reduced cover thickness, which is likely to have been due to poor construction in those patches. The construction of covers on minewastes is dependent on an adequate source of material meeting design specifications. From our limited examination, it appears that there was shortage of material for each of the three zones û a lower impervious clay layer, the moisture storage-release layer and the upper erosion-resistant layer for vegetative growth. An indication of this was that the upper layers in some areas were observed to be thinner than specified. We are of the opinion that this shortage of suitable material has been responsible for some of the changes observed ten years after emplacement. Physical and geotechnical testing indicated that the cover materials no longer meet the original specifications. In particular, the permeability at the 8 locations was found to be greater than specified, by up to several orders of magnitude. The higher permeability may explain the higher observed rainfall infiltration and moisture content of the waste rock. This increased permeability appears to be due to a combination of biological and physical processes û galleries formed by termites and ants and an extensive system of shrinkage/desiccation cracks formed by the development of a polygonal blocky structure involving the entire lower clay layer. The desiccation cracks may fill with coarser illuviated materials and form a conduit through which roots access the underlying waste rock. Measurements were made of oxygen flux into the heap as cover layers were excavated in the pits. They indicated that the full cover currently reduces the oxygen flux to 20 - 23 per cent of that into bare waste and that this reduction seems to be proportional to the cover thickness. It was also found that the oxygen flux into the cover is about four times higher at the end of the dry season than at the end of the wet season and that the difference is due primarily to the difference in moisture content of the cover. Recommendations are made for the design and construction of covers.

Jan 1, 2003

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultra- mafic complexes related to two orogenic episodes which took place during Paleozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe- Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

Results from current NERDDC funded research into the geotechnology of highwall trench mining methods have clear implications for mine planners in the areas of blast design, trench shape, location of the surcharge spoil and remnant coal pillar design.Adoption of successful smooth wall blasting techniques not only removes safety hazards from the trench face, but limits development of bedding partings at the seam contacts that interrupt the smooth transition of stress across the coal seam.

Jan 1, 1992

By F D. I Hodgson

Twenty-seven observation test pits were excavated at four different spoils dumps at three collieries in the Witbank Coalfield. The holes were dug into the upper three metres of the spoils to ascertain if any weathering profiles, variation with age or influence of topsoil covering could be gauged. Samples from these holes were also subjected to laboratory testing (ABA, humidity cells and mineralogy on several selected samples). The test pits showed that there was a good correlation between in situ paste pH-values and ABA results for samples taken from the pits. At all the collieries, no correlation between age of spoils and in situ acidity could conclusively be drawn. The depth of soil cover also appears to be a minor consideration in determining the eventual acidity of the spoil. In the pits where acidity was found, the weathering was evident when contrasted to areas still buffered. It is unclear if the weathering leads to the acidity or vice versa, as the soil covering appeared to be similar. The spoils proved to be extremely variable with regard to particle size and material on a micro and macro scale. Evidence from most of the holes suggested that there was enough water contained in the fine material in the spoils to support the initiation of acid generation. Conclusions from this investigation are that the mineralogy of the spoils is the most important factor in determining the eventual occurrence of acidic hotspots, and that prior characterisation and selective handling will provide the best management practice for these spoils.

Jan 1, 2003

By L Clarke, R N. Campbell, F Bourke, J Anderson

Lithological units have been classified geotechnically with mechanical tests and discontinuity measurements from the GRD Macraes Limited, Macraes Gold Project and Rotowaro coal mine open pits, New Zealand. Using these measurements slope stability probability classifications (SSPC) have been quantified based on an adaption of Hack's (1998) SSPC system which places less influence on rock quality designation and unconfined compressive strength than previous slope/rock mass rating systems. The Hack weathering susceptibility rating has been modified by using the chemical index of alteration values from XRF major element analysis. Slaking and weathering is an important parameter in slope stability in the Waikato Coal Measures and Otago schist lithologies and hence a non-subjective method of assessing slaking/weathering in relation to the chemical index of alteration has been introduced. Other major components of this adapted SSPC system are the inclusion of rock moisture content and rock strength anisotropy effects on slope stability. This paper explains the systematic approach of using the adapted SSPC system to classify slope stability probability. The main modifications of Hack's SSPC system are the introduction of rock intact strength derived from Mohr-Coulomb failure criteria which has been adapted for varying moisture content, weathering state and confining pressure. It is suggested that the subjectivity in assessing intact rock strength within broad bands in the initial SSPC system is a major weakness of the initial system. Initial comparison of rock mass friction angles, cohesion and strengths derived from the adapted SSPC are compared with results derived from modified Hoek-Brown criteria, MRMR and SMR classification systems. The advantage of the modified SSPC system is that slope stability probability, maximum batter and overall slope height and overall slope angle for open pit walls can be predicted in addition to orientation dependent and orientation independent stability. Examples are provided, using the modified SSPC system to predict initial optimum pit slope designs in proposed greenfield mine sites.

Jan 1, 2000

By M Miller

Operators of nickel laterite pressure acid leach and gold pressure oxidation technology frequently employ a series of steam condensing heaters to preheat the leach feed slurry. The heaters are an economic pinch point û although the thermal performance of the heaters is critical to overall process viability and operating cost minimisation, they are also a significant capital item and must be sized accordingly. Despite this, discussions of the factors underlying heater design are conspicuously absent from technical literature, and existing operations feature a conflicting range of heater sizes and configurations. This variety would suggest that at least some of the chosen heater designs are oversized. As part of its detailed design stage, the Ravensthorpe Nickel Project (RNP) constructed and tested a pilot plant heater to develop an understanding of the heating process and to ensure that the RNP heaters were appropriately sized. This testwork used RNP slurry at design density and viscosity on a 450 mm diameter, 6500 mm high column. The pilot plant testwork demonstrated the intrinsic efficiency of the direct steam condensation heating process, which was essentially independent of slurry density and viscosity. Presence of non-condensable gases in the steam phase decreased the heat transferred in certain circumstances, but heater performance remained consistent with thermodynamic limitations. Stagewise heat transfer within the column was rapid, and suggested either a very high slurry surface area or excellent heat transfer within the slurry phase. While the testwork did not set out to distinguish between these effects, physical evidence pointed to droplet formation in the inter-tray shower zone, giving a high heat transfer area. For scale-up purposes, the key facts were that the heat transfer rate was not limited by using high viscosity slurries and heaters could be designed using the principles applied to the smaller of those in existing operations. This paper discusses existing slurry heater designs, the current understanding from open literature, the pilot plant testwork, results and analysis, and scale-up to commercial sized equipment.

Jan 1, 2005

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was 'cupped' in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as 'piercing', the second stage being termed 'elongating.' In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947