Search Documents

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

The Abra mineralized body is regarded as a significant new style of mineralization for its environment. It is a blind polymetallic deposit, located in the Bangemall Basin of Western Australia. It was discovered by Geopeko in 1981 by diamond drilling a coincident magnetic gravity target, which revealed a large low grade epithermal Fe-Ba-Pb-Ag-Cu-(AuW) deposit, hosted by chemogenic and clastic sedimentary rocks, overlain by 200-500 m of clastic sedimentary rocks, of Middle Proterozoic age. The mineralization occurs as an upper stratabound phase, and a lower vein "stringer" style phase within a pervasive chlorite alteration envelope.

Jan 1, 1987

By Skaviniak M

Some better perspectives applying to the exploitation and dressing of polymetallic ores in the Banskfa. gtiavnica-Hod- rusea Ore District are supposed to be achieved after a suc- cessful investigation and proving there the existence of deep-seated mineralization as well as due to increasing de- mand for non-ferrous metals and consequently to higher mar- ket prices of those recently noticed. With respect to the present situation in mining and to the further technical development as well, a several times higher exploitation may be in this region expected, especially in the deeper .eated parts of the deposit. When solving the tasks of a complex economic exploitation over the whole region, consi- derable attention is paid to regional relations and impact studies (due to expected exploitation and ore dressing but also to very difficult problems of dewatering (drainage pro- blems-). It will be first of all necessary to find there an equilibrium between the consequences resulting from the re- naissance of mining industry and environmental requests un- dispensable for the city of Banska 9tiavnica and the other neighbouring towns in the vicinity of mining plants.

Jan 1, 1988

By Hiddlestone D. C

Effective exploration, testing and analysis is essential for good process design and optimisation of coal preparation plants. Coal processing relies on the sizing and washability characteristics of the particular coal to define the most cost effective design to meet the market requirements. Flowsheet development and equipment selection is dependent on the natural quality characteristics of the coal, its physical properties and the value of the final product in its market. The methodology of process selection and the key elements in design are discussed. Coal is consumed in two general markets: ò steaming coal - both domestic and export, and ò metallurgical coal. This paper discusses the typical economic analysis required to evaluate the potential for, and cost benefit of, providing the flexibility to switch coals between markets. A case study illustrates the methodology of process selection in a typical high value metallurgical coal.

Jan 1, 1997

By Sauer P

The paper deals with the method of operat- ion, types of construction and sizing of screening machines as well as the selection of suitable screen decks. The application of novel screening mac- hines in hard coal preparation plants is explained in detail by way of examples.

Jan 1, 1984

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

By C J. R Hart, J K. Mortensen

The distribution of mineral deposits within northwestern North America (Alaska, Yukon, and northern British Columbia) allows for an in-depth examination of the metallogenic patterns of a growing continental margin. A more complete understanding of the tectonic evolution of this part of the Pacific Rim, achieved over the last 15 to 20 years, now allows for the placement of ore systems into a well-defined plate tectonic framework. Ore deposits older than about 185 Ma represent hydrothermal systems that were active in the platform/shelf environment of ancestral North AmericaÆs miogeocline or hydrothermal systems developed in oceanic arcs and continental fragments more distal to the craton. These include important SEDEX, VMS, and pre-accretionary porphyry deposits. In contrast, most mineral deposits younger than about 185 Ma were formed within the growing Cordilleran orogen, as terranes were accreted to the continental margin during interactions between the North America and Pacific/Farallon/Kula plates. Such syn- to post-accretionary mineralised systems include many large lode gold and porphyry/skarn systems.

Jan 1, 1999

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By J Liu

In situ coal gasification is a method of extracting a high proportion of the energy value from coal without the need for mining. In situ conversion of coal to combustible gases is achieved by drilling wells into the seam, injecting gasification agents and initiating combustion. The product gases are then extracted to surface using production wells. These gases are clean energy sources for power generation, heating or synthetic fuel production. In situ coal gasification is of particular interest with respect to its lower environmental impact, potential application to otherwise inaccessible energy resources (ie offshore, deep deposits or beneath protected lands) and low capital intensity. Practical application of this clean technology is restricted primarily by lack of satisfactory quantitative descriptions of the processes involved, in particular the hydromechanical processes.In this study, three characteristic physical zones of an in situ gasifier are identified as the rubble zone, combustion front and virgin coal zone. Coupled mechanical processes of coal consumption and overburden collapse are used to describe the permeability profile in the rubble zone. Additionally, the redistribution of overburden load associated with coal consumption is accounted for with the formulation of a stress (compressive) dependent permeability profile, which is applied to the virgin coal zone. The model was implemented into and solved by FEMLAB, an advanced computer simulation tool. The flow process, according to DarcyÆs Law, is subsequently described in terms of permeability dependent injectivity. Injectivity is an indicator of flow velocity, which has been identified as a crucial factor in determining the commercial value of product gases from in situ coal gasification. The stress alteration to coal permeability was found to have a dominating influence on the flow process. This finding implies that a greater understanding of the in situ coal burning induced deformation of surrounding rocks would be of significant value in assessing the economic viability of applying this clean technology to potential sites.

Jan 1, 2004

By Thirnbeck M, Sione T, Petrie P, Leach TM, Mori W, Digan K, Harry K

Gold and lesser copper mineralisation are associated with porphyry-related vein systems periph-eral to two separate inferred intrusive centres north of Kainantu, Papua New Guinea (PNG). The intersection of NW trending structures, formed parallel to the Markham Fault, with NE trending transfer structures localise porphyry intrusions, and control vein distrib-ution.The Arakompa veins intrude pre-existing fractures in Akuna granodiorite, located proximal to an inferred porphyry. These veins are characterised by early quartz and later pyrite-chalcopyrite. Gold mineralis-ation is associated with Bi-Te phases in the sulphide veining. At Maniape, en echelon gash veins occur within the imbricate portion of a regional structure. Maniape is a high level carbonate-base metal gold system formed distal to the same porphyry source as Z ?-;4 kmmna

Jan 1, 1994

By Beech-Jones J. M

At Port Latta in Tasmania, Savage River Mines operates vertical shaft furnaces for the firing of pelletised magnetite concentrates. At times the temperature profile of the furnace has changed markedly, necessitating the- burning of greater quantities of fuel to maintain good pellet quality. A study of the oxidati=of magnetite concentrates was under- taken because this exothermic process supplies much of the heat required to indurate the pellets. Using the thermal analyses methods, different magnetite concentrates from Australian and overseas were heated in air under identical conditions, to compare rates of oxygen uptake and of heat release. In addition, a compari- son was made of the oxidation behaviour of different particle size fractions of a selected concentrate. Particle size analyses, x-ray diffraction and dilatometer tests were used to aid inter pretation of the thermal analysis traces. The investigation emphasized the importance of particle size and ferrous iron content in determining' oxidation rates from the commencement of heating.

Jan 1, 1974

By Taylor G. H

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopical techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relat- ing their inherent properties to properties such as volatile- matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used coimierciallyti,

Jan 1, 1969

The Mary Kathleen uranium deposit occurs in 1740-1780 M yr-old calc-silicate melasedimentary and mela-igneous rocks of lhe Corella Formalion which have been tightly folded into lhe Mary Kathleen Syncline. The Corella Formation consists of malic and felsic tuffaceous(?) calc-silicates, quartzile, and minor marble, conglomerate and basic volcanics. Garnet-rich rocks form semi-concordant and transgressive masses in the middle and upper portion of the sequence. Granite, gabbro and acid porphyry dykes also occur in the syncline.Uranium-rare earth mineralisation is closely associated with certain malic rocks and occurs wilhin or close to garnet-rich masses. At Mary Kathleen, uraninite grains are enclosed mainly by allanite which is dislribuled through massive garnet as an irregular honeycomb of interconnected shoot and lenses. The mineralisation occurs along strike from dioritic rocks and conglomerate and lies close to the axis of the Mary Kathleen yncline and adjacent to a major faull zone. All other localities allanite-uraninile mineralisation is broadly stratiform.The mineralisation is interpreted to occur at or near centres of basic volcanism. Garnet formation and uranium-rare earth concentrations are believed to be caused by the volcanism, and to be contemporaneous with it. The former is seen as alteration of a hot, saturated pile of volcano-sedimentary material and the latter as intermittent hydrothermal exhalation.Deposition, volcanism, garnet formation, uranium and rare-earth mineralisation, granile and gabbro formation, and tectonism are seen as a continuum of interrelated processes which operated throughout the period of format ion of the rocks in the Mary Kathleen Syncline.

Jan 1, 1985

By M D. Raine, J K. Bartlett, S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of fields that make up the Central Victorian Goldfield. Since 1993, Bendigo Mining NL has been carrying out an extensive re-evaluation of the goldfield and is currently well advanced in developing an underground mine. The sediment-hosted auriferous quartz reefs are structurally complex and closely associated with anticlinal axes and reverse faulting. The gold within the quartz reefs is characterised by both its coarse nature (100 up to >5000 ¦m) and its erratic distribution; as a result, the Bendigo Goldfield is classed as an extreme nugget effect system. This characteristic ensures that the Bendigo mineralisation is very challenging to sample and evaluate. In this case, diamond drilling is a good measure of structure and geological continuity, but a poor measure of grade and grade distribution. Drilling, combined with on-reef development, bulk sampling and detailed geological studies are required for resource evaluation. For grade control a balance has to be sought between sample representativness, cost, turn around time and practicality. Extreme nugget effect deposits like Bendigo, require the use of bulk samples in order to be representative. However, the cost and turn around time is significant. As a result, a micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can define ore from waste. Bulk sampling and on-vein development are still necessary for resource and reserve estimation.

Jan 1, 2003

By Payne P, Beirne W, Geldard D, O&apos

Whim Creek Consolidated N.L. has operated openpit mines at Meekatharra since 1980. Mining operations commenced with the Haveluck openpit and the Phar Lap openpit was started in 1 984. Grade control in the Haveluck mine was simple because the orebody showed good continuity along strike and down dip and had an easily recognisable hanging wall contact. Problems were encountered once mining corn menced at Phar Lap because of the complex lithologies, alteration and faulting involved. Simple grade control techniques developed for Haveluck failed and were not solved until an understanding of the ore bodies was achieved.The integration of all geological data into the interpretation of the developmentdrilling results has proved essential to achieve effective grade control atreasonable cost.

Jan 1, 1986

FOR some reason there is not any extensive literature in print on the electrolytic refining of copper, although the method is in general use in America and Europe. In Australia there are but three plants in existence one small one at Wallaroo, in SouthAustralia; one at Lithgow and one at Port Kembla the last two being in New South Wales. The largest of these is the Port Kembla plant. It is also the most modern, and embodies all the latest appliances and improvements of electrolytic practice.The plant and methods about to be described is that at Lithgow, with which the writer was associated for some years, and the experience gained there may be of interest. Electrolytic refining of copper is one of the simplest operations of metallurgy, but, like all metallurgical operations, it requires constant attention and a large amount of common sense. The man in charge should be endowed with an insatiable curiosity as to why certain things are occurring, and an instinct of cleanliness, whichmy first mentor in chemistry, Mr W A Dixon, once impressed on me was better than godliness.

Jan 1, 1911

By Brinkmann J. R

In the narrow stopes of South African gold mines, rockbreaking is carried out by drilling and blasting with safety fuse and igniter cord being used as the initiation system. The fuse/gniter cord system is used primarily because of its low cost, however several limitations of this method include: inaccurate delay time, unreliable firing, inflexible application to varied configurations, and the absence of dynamic interaction between holes. Alternative initiation systems that incorporate millisecond timing are being developed to overcome the limitations of fuse(tgniter cord systems. Current investigations by the Stoping Technology Division of the Chamber of Mines Research Organization (COMRO) into the effects of millisecond initiation are being conducted at a deep test site. Experimental blasts using various millisecond delays and the independent firing of holes with fuse/igniter cord are being studied in order to quantify the influence of delay time on the blasting process and to identify the best methods of applying millisecond initiation systems. The effect of design variables such as delay time, hole firing pattern, stemming, and panel layout are discussed. Blast results including throw distance and direction, muckpile profile and rock cleaning times are used in the discussion of different combinations of blasting variables.

Jan 1, 1990

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

LITHOPROBE is a national, collaborative research grogram with the general objective of understanding the teotectonic evolution of the North American continent through multidisciplinary lithospheric studies in carefully selected areas of Canada. Six transect areas are investigating Precambrian evolution, although only in two of these is the research well evolved. The Archean Kapuskasing Structural Zone in Ontario is confirmed as an upthrust slice of upper to mid crust exposed at the surface. The Late Proterozoic Keweenawan mid-continent rift is shown to be the deepest known rift on Earth and the Grenville collisional zone of Ontario and Quebec involves crustal scale imbrication and ramping of deeply buried rocks to the surface. Two transect areas are investigating Phanerozoic evolution. In the Newfoundland Appalachians the geologically defined tectonostratigraphic domains do not coincide with lower crustal blocks defined by seismic reflection data. The Southern Cordillera Transect in western Canada is examining the nature, timing and dynamics of the assembly of the Cordillera, and particularly the role of accreted terranes. Work in the eastern and central segments has extended the known western limit of the North American craton at least IOO km westward and crustal-scale ramps associated with metamorphic core complexes have been identified.

Jan 1, 1990