Search Documents

As this Seminar is on "Progress - Mining and the Environment", I am taking the liberty of extending my address beyond the scope implied by the subject, "Rehabilitation of Mined Land", with a preliminary discussion on broader economic issues relevant to "Progress and Mining in Western Australia" before discussing its effect on the Environments Western Australia is nearly one million square miles in area and has a population density of approzimately one person per square mile. Because of its vastness it has wider climatic variations than any other Australian State. The north is tropical and the south is in the temperate zone. The major portion of the State is an arid plateau with less than 10 inches of mean annual rainfall. The climate, rainfall and soil conditions of the South-West region are more favourable to agriculture than any other part of the State and consequently was settled first. The immediate need of the colonists being food and shelter, the early economy was based on farming and forest products.

Jan 1, 1971

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By A Black, A de Jo, J Cavanagh, J Harding

Acidic and metal-rich waters have been discharging from Sullivan Mine, West Coast, New Zealand since the closure of the mine during the early- 1990s. This has resulted in a decrease in pH from a background of 4.5 to 2.8 and an increase in metallic elements in nearby Rapid Stream. In addition to the chemical effects on Rapid Stream, a study of freshwater macro-invertebrates revealed the absence of most biota downstream from the discharge. An attempt is being made to use the Sullivan Mine as a case study of problem and remediation analysis.

Jan 1, 2003

By C Fearon

This paper discusses the implementation of an underground rail haulage system during a major expansion of the Olympic Dam mine in 1998. The factors affecting the selection of rail haulage are discussed and details are provided on the rail system, which is designed to transport more than 10.5 million tonnes per annum (Mtpa). The reliability of the system during commissioning is discussed, including the decision to manufacture a ædummyÆ locomotive in order to keep the system operational. Finally, reliability improvements made both during and after commissioning are discussed with comments provided on the effectiveness of the system as it operates today.

Jan 1, 2005

In 1985 a 2.5-tonne top blown rotary converter was installed in the silver refinery at Cominco's Trail Operation to carry out the final cupellation of burndown metal to Dore metal. The furnace is fired with an oxygen-natural gas lance which is capable of achieving a variety of furnace conditions, varying from reducing to highly oxidizing. Reaction rates are about 4 times greater than using conventional cupel furnaces. The faster reaction rates improve productivity and reduce in-process precious metal tie-up. The furnace is also used to reduce litharge slag for bismuth recovery.

Jan 1, 1989

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002

By Conochie DS

SIROSMELT is a successful new pyrometallurgi- cal furnace system using a top-entry lance which can be submerged in both slag and matte. The lance is of simple construction, and is cooled by process air. Pilot plant work commenced in the CSIRO Division of Chemical Engineering in 1972 using a 50 kg batch reactor. This paper traces the development of the technology through various slag cleaning and smelting processes up to a scale of 5 tonnes per hour continuous feed. Strong co- operation between CSIRO and the Australian smelting industry has contributed greatly to the success of SIROSMELT.

Jan 1, 1984

By Gregg PEH, Stewart RB

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed. After seven years, the rate of increase of N, C, P and S, losses of S and P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site.

Jan 1, 1995

By N Kreutzman, A Moilanen, V Palosaari

Carboxymethyl cellulose, CMC, is widely used in mineral processing as a flotation depressant, mainly for the depression of carbonate and talcaceous gangue in the flotation of Cu-Ni sulfide and PGM ores. Although CMC is a common depressant that can be used in the flotation of different ores, understanding of the interaction mechanisms between CMC and mineral particles in different flotation circuits and different pulp conditions is still limited. Electrokinetic measurements, microflotation and laboratory-scale flotation tests were carried out to optimise the action of CMC depressants in the flotation of a PGM ore. Standard and new CMC brands produced and characterised by Noviant were used in the study. Pure talc and chlorite minerals and a low-grade PGM ore composite were used as test materials. A laboratory flotation test evaluation was performed using the recovery-grade relationship and double value index (DVI) calculation to estimate the effects of both valuable and harmful components on the product value. Solution conditions play an important role in the depression of gangue minerals such as talc. The most favourable conditions for MgO depression were found to be mildly acidic in which conditions the electrostatic repulsion between the CMC molecule and talc is minimised. Similar effects were obtained with electrolytes that affect the conformation of the CMC molecule and the mineral surfaces. In addition to the control of chemical conditions in the pulp, CMC molecules were modified to optimise structural variables. The new CMC brands developed in this work showed significant potential to improve flotation performance, particularly when pulp conditions are controlled.

Jan 1, 2005

By Keren Z, Huanguo G, Jlchuan Q

In this paper, the authors introduce a new flotation technique, a double collection flotation precess, which succeeds in separating feldspar from quartz effectively in weak acidic medium (pH = 5-6). In the presence of sodium hexametaphosphase(HMP), sodium oleate selectively improves the floatability of feldspar in the first collection step. Dodecyl amine- hydrochloride is used as collector in the second collection step to separate feldspar from quartz. The flotation tests with pure minerals as well as artificial mixture give out satisfactory results. The mechanism of reagent effect was investigated briefly, which is helpful for understanding the Process.

Jan 1, 1993

The smelting operation associated with the production of aluminium has a voracious appetite for high grade carbon materials. Within the technical parameters of the Hall-Heroult process, the reduction of alumina to one tonne of aluminium results in the consumption of nearly 0.5 tonne of carbon at the anode of an electrolytic cell. This paper reviews the role of carbon and the basic quality requirements of carbon products in the production of aluminium, discusses the effects of certain physical and chemical specifications on smelting and related operations, and examines recent trends in the quality of these raw materials.

Jan 1, 1977

By Bradford NL

The Isa Mine of Mount Isa Mines Limited produces 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore from sublevel open stopes annually. Extraction of the narrow, steeply dipping silver-lead-zinc orebodies requires a strategy quite different to that used in the massive copper orebodies. A range of blasthole diameters, explosive types and initiation systems gives the flexibility needed to adapt open stoping to a variety of situations. Hole diameters from 70 mm to 200 mm are being used, with lengths of up to 100 m common for the latter.

Jan 1, 1982

Extensive infrastructure construction works were required for the development of the underground and open-cut coal mine at Ulan to a production capacity of 5 million tonnes of steaming coal per annum. The Ulan Mine development project was constructed in a two year period at a cost of $240 million. The infrastructure component included the construction of the mine site building works, civil works and 150km of railway, valued at $105 million. These works were successfully completed under a construction management agreement within two years. The separate elements of the project are described in detail in the paper.

Jan 1, 1983

By G Varley

This paper describes the mining methods and strategy used to extract the 5 Orebody crown pillar at the Isa Lead Mine over the past five years. The bulk of the crown pillar was extracted by the use of sublevel open stope method. An uphole bench stope was mined to scavenge the remaining ore. Geomechanical issues associated with the crown pillar extraction are described. Stope sizes were gradually increased on a stope by stope basis. This has allowed the maximising of ore recovery while relevant risks were managed. The principles in designing ore rib pillars against various types of fill materials are also described.

Jan 1, 2002

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999

As part of its Concentrator operation Hamersley Iron Pty. Limited uses wet high intensity magnetic separation to upgrade shaley low grade ore in the minus 0.5mm size range. Materials handling problems, largely caused by fine ore types and design deficiencies, surfaced in the Fines Treatment Plant soon after Concentrator commissioning in 1979. Surging throughout the circuit impaired process efficiency and added to problems caused by capacity and process control limitations. In 1981 extensive modification works were initiated to supplement minor changes made to that date. The new circuit significantly increases capacity and provides greater process control.

Jan 1, 1978