Search Documents

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

The Central Andes in Peru, Chile, Bolivia, and Argentina, contain two contiguous terranes which were accreted i, Gondwanaland between the end of the Devonian and the end of the Triassic. These terranes, Arequipa in the north, anni Chilenia in the south, differ from each other in the timing and style of their metallogenic development. However, they contain over 90% of the Central Andean porphyry copper resource. The copper porphyries in the Arequipa terrane are Paleocene to lower Oligocene in age, whereas the Chilenia deposits are mid-upper Cretaceous and mid-upper Miocene. Porphyry copper deposits occur outside these terranes, but are all Miocene in age. Miocene porphyry-style mineralisation also exists in the Arequipa terrane, but is copper-deficient and gold-rich. The accreted terranes may have favoured porphyry and other styles of copper mineralisation because they possessed relatively thin continental crust compared to adjacent parts of the Andes. Crustal thickening which commenced at about 30 Ma in the Arequipa terrane coincided with a major change to polymetallic, precious metal mineralisation which commonly displays high sulfidation charcteristics.

Jan 1, 1995

Synthetic seismograms of reflectivity method and some field records available are studied to detect the amplitude anomalies at the interface of the gaothermal reservoir the gas and/or oil boundary, and the underground tunnel. The first arrival of PO wave on the P-SV record are weak and emergent while those of P wave only rotated with respect to an incident angle are clear. This can, be explained by means of the energy loss of P-SV wave conversion. The primary reflections of P waves about depth fade away as compared to SH waves which do not perform any conversion, although they hold high attenuation in the fully saturated fluid layers. Reflection of comparable strength is present at the P-wave and S-wave... boundaries, but gas-saturated zones correlating with P wave bright spots do not show equivalent attenuation anomalies. Thus the comparative technique of P-SV wave and SI i wave records is very useful to indicate the strong amplitude anomalies at the boundaries of sealing targets.

Jan 1, 1990

By Manlapig E. V

ABSTRACT- I Results are given for a series of tests in which a 300 mm pilot-scale Jameson cell has been used in copper recleaner flotation, and for the flotation of a lead rougher feed. the results indicate that the production rate of solids, at the same superficial air velocity Jg, is higher than in conventional columns. Thus in the copper recleaner application, the pulling rate reached 14 gm/cm2/min compared with between two and three for an operating column, while in the lead cleaner application the comparable figures were 12 - 14 gm/cm2/min for the Jameson cell vs 8 - 9 gm/cm2/min for a test column. A froth crowder was used to increase the air superficial velocity Jg in the Jameson cell in the copper recleaner, while holding the collection mechanism and pulp feed rates constant. The recovery increased from 50 per cent to over 90 per cent, suggesting that recovery is controlled mainly by the froth conditions, rather than the particle-bubble interactions in the Downcomer.

Jan 1, 1991

By Hunefeld R

In the field of mining engineering, design and planning are complex tasks, which require the knowledge of various engineering disciplines. GRUBE (Graphisch-RechnerUnterstiitzter BergwerksEntwurf) is a modular databased program system, which offers computer aid for all mining departments using a 3D CAD software as the user interface. Despite the data quantity and complexity, specific and uniform working conditions have to be applied to the planning of technical equipment of a pit. With the application of 3D graphics, complex data stores and their interrelations become 'palpable' for the user by suitable visualisation. GRUBE-M forms the mechanical operations module of GRUBE, in which underground locations displayed as three-dimensional graphic models are `equipped' interactively. Planning alternatives can be created and compared quickly in terms of technical calculations and economical analysis.

Jan 1, 1995

By McKee DJ

Many workers have observed an inverse relationship between final concentrate grade and valuable component recovery achieved by a flotation circuit, i.e. an increase in either grade or recovery may only be achieved at the expense of the other. The relationship is termed a "grade-recovery" curve and, in theory, limits the separation obtained by the circuit. However, circuit surveys in a nickel concentrator indicate that the operating "grade-recovery" curve of a circuit is not only determined by the nature of the ore and the circuit operating conditions, but also by the circuit design, particularly in terms of stage capacities. The surveys show that different capacity circuits can produce different operating curves for the same ore, and that capacity reallocation between stages has the potential to improve both grade and recovery. In particular, the relationship between circuit design and operating curve position is shown to be a function of the circulating loads generated by the circuit design, balancing the beneficial effects of recycling material against the proportion of plant capacity consumed by recycling.

Jan 1, 1986

By Sullivan BJK

The 1100 orebody is a massive copper sul- phide orebody which contains a major portion of the Isa Mine copper ore reserves of 130 million tonnes at 3.2%. The underground mining of a deposit as large as the 1100 orebody is technologically a complex operation as extraction strategies have to be evaluated with reference to 1. rock mechanics considerations, 2. safety and environmental standards, 3. production and operating require- ments and 4. metal recovery and costs. The mining philosophy in the orebody has undergone considerable change over the past five years as a result of experience and improved technology. At this stage, primary stopes are extracted by high rise sublevel open stoping and pillars by slot and mass blast drawn either under rock fill or as an open Stope.

Jan 1, 1978

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

By S Blackburn, T Veasey

The physical and mechanical properties of rock can be measured by a variety of standard tests, and studies have shown that there should be a fundamental connection between breakage in comminution and rock æstrengthÆ. The current study aims to develop the ring-loaded strength test, used as an industry standard for the characterisation of brittle ceramics, for determination of comminution behaviour from exploration borehole core samples. The test procedure is simple, reproducible and can yield 250 separate measurements from a one metre length of drill core. The effects of material grain size and fabric on the degree of scatter of results have been investigated with respect to the ring-loaded strength test. This study has also compared the ring loaded strength to the chevron bend test used to determine the Mode I fracture toughness. A wide range of rock materials have been studied and with further work it is conceivable that an operational work index could be obtained directly from exploration drill cores tested via the ring-loaded disc test.

Jan 1, 2000

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

One of the most frequently asked questions at the feasibility study stage of a project is, æhow big can one go?Æ This important question effects costing and efficiency of metallurgical equipment, the real estate required and the operating plant strategy.The presentation covers both engineering and process considerations and explains the limits that exist today and explores future trends.The paper is specific about large slurry application usually found in gold applications; however, it could apply to silver and uranium or other dense media leach duties.Agitator drive sizes are examined as well as process risks associated with large tank agitation. New technology has increased the maximum tank size and designers are now experienced in tank volumes in excess of 5000 m3. Tanks of 6000 m3 have been agitated and 10 000 m3 tanks are within present engineering know-how and scale-up.Fabrication techniques for shaft and impeller designs exceed the existing standards and new specifications will be needed to cover large mixer design. The paper covers certain aspects of mechanical design and proposes alternative standards that are more appropriate. Process considerations such as fluid natural frequency as well as typical superficial velocities for efficient operations are examined. Scale-up techniques based on existing and new technology are also examined to ensure a successful installation.The presentation therefore covers the majority of large mixer design questions that are frequently asked.

Jan 1, 2006

The techniques used in evaluating gold placers and in recovering gold therefrom are briefly reviewed and critically assessed, relative to the estimated and actual recoveries from many operations. The discrepancies between these quantities can be significant and sometimes disturbing. The coefficient of variation for the annual percentage recoveries, relative to the estimates, is in excess of 10 and commonly above 20 . The difficult- ies in evaluating placers are recogni- sed both in the gathering of meaning- ful sample data and in the derivation of estimates. There are deficiencies, perhaps insurmountable at reasonable cost, in the techniques used to derive an estimate and in the gold saving devices usually employed. There is a subconscious trend to use recovery as a check on the estimate. The industry could have extracted more information during the evaluation and working of deposits in order to fully characterise them and in order to quantify metallurgical efficiency. There is a place for other prospecting techniques, particularly geophysical, in placer evaluation and a need for more appropriate and sophisticated

Jan 1, 1976

Blasting, particularly bench blasting, uses finite length cylinders of explosive close to two free faces. The rock to be blasted is usually intersected by a complex 3-D system of joints. To fully simulate a blast, a 3-D dynamic model is required. It is shown that the static stress distribution around a long cylinder can be reproduced by superposing the static stress distribution of a suitable chain of spheres. Thus, the dynamic results for individual spheres given by Favreau (1969) can now be substituted for the static results to give a dynamic model of the stress distribution around a long cylinder. Comparison of measured and computed waveforms show that the measured waveforms are much more attenuated and dispersed than expected. The consequences for explosive evaluation and design are Discussed.

Jan 1, 1990

By Palmer C. G, Rowe P. G

Ore handling improvements at Mount Isa Mines Limited were necessary to keep abreast of technological advances in all phases of sublevel stoping practice.In the early 1930s an efficient ore handling system was in operation.However in 1936 excessive water encountered in deepening the hoisting shaft necessitated the sinking of a second hoisting shaft. Financial difficulties prevented abandoning the original shaft and surface ore handling and crushing facilities, so ore was transferred underground and underground crushing deferred. It was not until 1951 Jhat multilevel crushing permitted increased efficiency in the handling of ore from stopes. Ore was then hoisted in one shaft and transferred on the surface by conveyor belt to a new crushing plant.In 1956 a planned production increase from 5,000 to 11,000 tons per mining day made possible further improvements in ore handling. Larger equipment was installed and existing equipment modified to capacitate the handling of larger sized ore at increased daily tonnages.INTRODUCTIONThe intensive exploratory programme commenced in 1954 disclosed large reserves of both lead and copper ores and in 1956 an expansion programme was initiated to increase production from 5,000 to 11,000 tons per mining day. The increased tonnage would result in decreased costs per ton and further cost reductions would result from increased mechanisation underground. The combined effect would permit larger tonnages of lower grade ores to be included in ore reserves. To achieve both cost reduction and the scheduled production increase, improvement in ore handling was of vital importance.For efficient and low cost sublevel stoping it is necessary to maintain an economic balance between...

Jan 1, 1961

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

Models of the genesis of existing ore oodles and targetting of exploration for new mines are greatly enhanced by an-understanding of the plate tectonic environment existing at the time of mineral emplacement. In areas of recent or active tectonism, a study of the present-day crustal and upper mantle structure is an obvious starting point in unravelling the evolution of the accessible upper crust. Bougainville is the northern-most island in the Solomon Islands arc. A 7km deep trench almost 100km off its western coast marks the commencement of subduction of the Solomon Sea plate beneath the Pacific plate. As outlined by the seismicity, the subducted crustal slab under the southern half of Bougainville reaches the axis of the island at about 100km depth, from which point it dips near vertically another 300km into the upper mantle. Large surface blasts at the Bougainville Copper Mine at Panguna, Bougainville, Papua New Guinea were used to derive an unreversed upper crustal profile of the island. The crust appears to be relatively simple, being comprised of a 5km deep layer with a P-wave velocity of 4.5km/sec, overlying a l0km thick layer with a P-wave velocity of 7.2km/sec. Constraints on the 15km mantle depth were provided by the identification of both P to and S to P phase conversions of seismic waves from local shallow earthquakes at the Moho boundary. An upper mantle velocity of 7.95(¦ 0.15) km/sec was measured from travel times of selected shallow earthquakes along the strike of the island arc.

Jan 1, 1987

In the Ora Banda area of the Eastern Gold- fields, the ultramafic rocks tend to be more deeply lateritized than most of the surrounding rock types, and lateritic nickel concentrations have been formed. Extensive drilling_has shown that, of the two intermixed suites be- neath the laterite - an extrusive peridotite- pyroxenite suite and an intrusive, highly magnetic dunite - the latter weathers to a more nickel enriched laterite. The top horizon I of the laterite consists of ferricrete. Horizon II consists mainly of bands of secondary silica in a clay matrix, formed in the reworking zone around the water table and stranded as the weathering profile migrated downwards. Horizon III ('ºaprolite") is composed of serpentinite, magnesite, iron oxides and silica, and grades dowil to the fresh bock composed variously of olivine, ser- pentine, talc, amphibole-chlorite and iron oxides. The main locus of nickel deposition is the zone containing the bottom of horizon II and the top of horizon III. The water table is also at this general level. .

Jan 1, 1973