Search Documents

By A Fitzpatrick

An integrated and dynamic water balance and water quality model for a proposed base metal mine has been created using the GoldSimÖ software package. The model was initially developed to address the water quality of the Tailings Management Facility pond and how pond discharge would potentially affect downstream water quality. However, due to changing project objectives, the modelling has expanded over time through an iterative process to encompass the full mine site and all receiving environment water quality. The model results have been used as part of the mine planning/design process but are also intended to be used for the environmental impact assessment and permitting process. The model has been built to allow for changes to input terms to be readily made as additional data becomes available. The model results serve as a prediction of water quality and the potential project impacts to the receiving environment water quality. This paper presents the process by which data from a wide variety of sources was used to construct the model and how the model results were used to guide development of a conceptual water management plan. In addition, the role of the model in establishing proposed discharge criteria will be highlighted. The model has been delivered as a fully functional application with the intent that the end-user can be other than the modeller, the development of this aspect shall also be covered. CITATION:Fitzpatrick, A, 2012. Predictive site-wide water quality modelling as a tool for mine planning and permitting - A recent Canadian example, in Proceedings Life-of-Mine 2012 , pp 71-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Structural analyses of oriented bore core sections from the West Wallsend No.2 Colliery Holding together with investigations in adjac- ent collieries and on the surface delineated structural phenomena. The rocks examined are anisotropic due to strongly developed bedding planes and the presence of penetrative joint planes. Joints, in this context, are regarded as mechanical discontinuities, they are genetically identif- ied wherever possible and their spatial attit- udes are determined and geometrically related to the regional structure. Identifiable anisotropies in the roof- and floor-strata of the Borehole Seam render favour- able mining directions for longwall and bord and pillar layouts.

Jan 1, 1972

By B Patterson, Y Lanwin

Over the last decade the adoption of autonomous technology has proven its potential to fundamentally alter the mining industry, offering significant improvements in safety and productivity. Automation levels are now increasing exponentially across all parts of the supply chain from drilling, haulage, processing, rail and shipping to the maintenance of the above. However, the management of human error risk is also becoming increasingly complex as the disconnect between the people who operate and interact with mining equipment and those that design the autonomous systems grows in terms of skill and expertise. Furthermore, as comfort levels with automation increases amongst operators, complacency is increasing as the initial functional safety benefits have been realised. This paper introduces an innovative concept that unites two distinct fields, functional safety and behavioural economics, to address the complex issue of human error risk in autonomous mining operations. Functional safety, a well-established field in engineering involves identifying potential hazards, assessing risks and designing systems in a way that minimises the chances of accidents and limits their consequences. Meanwhile, behavioural economics takes a data centric approach to analysing the psychological aspects of human decision-making, acknowledging and seeking to understand the errors that can originate from cognitive biases and heuristics. This paper seeks to bridge these domains by emphasising that human error in autonomous mining is not solely a technical issue but is deeply influenced by human behaviour and decision-making processes. By incorporating insights from behavioural economics, we can better predict, prevent and manage human errors in the mining sector. By applying principles from both disciplines to a recent incident example we will explore how cognitive biases can impact peoples’ interactions with autonomous mining equipment. This interdisciplinary approach will not only enhance the design and implementation of functional safety measures in mining but also lead to the development of people centric solutions that consider the inherent fallibility of people. We will explore how human centred design can help bridge the gap between these two domains and apply systems thinking for a universal approach. Through an indepth case study analysis and empirical data, our research aims to provide actionable insights and practical recommendations for mining industry professionals, regulators and stakeholders involved in the safe integration of autonomous systems.

Apr 16, 2024

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By R M. Lonsdale, M D. Goodz

"With an ever-increasing dynamic business environment, successful stakeholder engagement is becoming more fundamental to achieving desired outcomes in today’s mineral resource industries. It is imperative to be proactive in correctly identifying all stakeholders and initiating early contact. This builds trust relationships, which are essential to ensure future decision-making processes are streamlined.Often neglected is a company’s obligation to select the correct team to represent its values and mission. The company requires representation that demonstrates an understanding and commitment to its operations and people, the safety and health of the community and environment, and most importantly, represents the decision makers. Stakeholders need to believe that the engagement process is genuine and that the company representatives are aligned towards targeted outcomes that will benefit all stakeholders in some way.Among others, stakeholders include shareholders, staff, families, community, service and supply providers, regulators, land managers and the political/financial framework. Depending upon the mineral product, stakeholders may include ports, international offtake clients and those along the route. New stakeholders continually evolve during mine life, and the engagement process requires an investor–community–public relations (IR/CR/PR) team to anticipate change and actively scan perception and chatter.Successful communication is more than delivering a message; it is about engaging stakeholders and confirming the feedback loop to ensure the correct message is communicated and the relationship is strengthened.The nature of the mining company’s branding and the public’s perception of company intentions will dictate whether there is willingness to allow the company to follow its desired path. This in turn controls the company’s most scarce resource – time. Timing is fundamental to achieving targeted outcomes with minimal cost and delays, marketing in a peak cycle and acquiring critical capital for development and growth.Branding and stakeholder engagement effectively controls and extends to the company its social licence to operate.CITATION:Goodz, M D and Lonsdale, R M, 2016. Stakeholder engagement – who are you, what do you stand for and why? In Proceedings International Mine Management Conference, pp 239-248 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

It is with great pleasure that I accepted the invitation to make a closing address to this Congress particularly as it is here in Brisbane. The main duty of the International Mine Ventilation Congress Committee and in particular the chairman is to ensure that these conferences are held every four to five years in suitable locations. My main role over the last four years has been to promote holding this Congress in Australia and it was a great relief when the Queensland team and the Australasian Institute of Mining and Metallurgy accepted the challenge in November 1986.

Jan 1, 1988

In 1975 the US Bureau of Mines (BOM) under contract with the Bureau of Indian Affairs (BIA), began a systematic mineral resource evaluation of Indian reservations in the United States. The purpose of the BIA/BOM program was to stimulate economic development on Indian lands through exploration and mining ventures with the mining industry. Since that time, 109 phase I reports (literature studies) and nearly 45 phase II and phase III (field studies) reports have been written by the BOM. The various tribes in conjunction with the BIA have access to these reports for decision making regarding mineral resource development.

Jan 1, 1990

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

Consideration of the questions: (i) is it feasible to study groups of processes in a generalised way? (ii) to what extent does purpose affect the form of a process model? (iii) are there any significant, novel investig- ations which can be made by computer simulation? (iv) what long-term developments are desirable in extractive metallurgy? has led to some new broad objectives for research in hydrometallurgical process engineering. Propositions for grouping processes, developing models for different specific purposes, using a systems engineering approach and developing high technology processes are discussed, and the role of computer simulation indicated by reference to particular projects.

Jan 1, 1984

By D J. Brake

Faced with the need to improve workplace conditions in both its development and production headings in its existing K1 orebody, as well as its new K Link and K2 orebodies, the Kencana mine in Indonesia took the novel approach of reversing the ventilation on most of its access ramp by outcasting up the ramp to the portal. Working levels were then fed with fresh air via auxiliary fans sealed into the current surface ‘egress’ intake raises (ladderways) or another small surface intake raisebore rather than from fans hung in the ramp as in the past. Outcasting the portal provided a substantial increase in the total mine exhaust capacity allowing fewer levels to be ventilated in series and significantly improving conditions, especially in the most difficult workplaces to ventilate. It also reduced the consequences if there was to be a fire on a vehicle in the ramp. The same system using the ramp as an exhaust is also intended to be used as part of the final ventilation solution for the new K2 orebody which also uses a novel single surface ventilation shaft that is vertically split into separate intake and exhaust compartments using a concrete brattice. Using the main ramp as an exhaust has potential application in many other operations in Australia using surface ramps which otherwise frequently suffer from overuse of series ventilation circuits and poor working conditions at the mine bottom.

Mar 21, 2011

By G Jones

The Singapore Land Transport Authority (LTA) has been procuring the expansion of their underground mass rapid transit rail network at a prodigious rate since the first line opened in 1987. Four lines (149 km) are currently operating and several more lines are at various stages of planning/construction; one of these is the Downtown line stage 2 (DTL 2).DTL 2 contract C917 was awarded in September 2009 for S$320 M. On 18 June 2013 the original contractor became insolvent, leaving the works incomplete. Following a fast-tracked tender process, McConnell Dowell was awarded the S$254 M contract on 29 August 2013 to complete the works. This contract includes two underground stations constructed by cut-and-cover methods and twin bored tunnels between the stations. Each tunnel is 1400 m long, excavated by earth pressure balanced (EPB) tunnel boring machines (TBM) at an average depth of 20 m and segment lined to 5.8 m inner diameter. The tunnel alignment is located under a busy five-lane road lined with prime residential real estate and congested with utilities.To compound the difficulty the tunnels are located within the notorious Bukit Timah Granite formation. This has a very wide range of strength, from below 1 MPa to over 300 MPa. This strength range is a consequence of six weathering grades, from soil to fresh rock, with the fresh granite causing severe abrasion problems. The various grades can occur within a very short distance of each other. Consequently, the problem of supporting a mixed face exists, particularly in the intermediate weathering grades where intact rock is encountered in the invert and corestones within a loose soil matrix in the crown, which can increase the instability by allowing the ground to flow into the TBM.The focus of this paper will be the excavation of the bored tunnels by EPB TBM used by McConnell Dowell to complete these challenging works.CITATION:Jones, G and Shepherd, J, 2014. Earth pressure balanced tunnelling in a dense urban environment, C917A, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By M Steinberg, M Amarant

Upstream Classifier are well-known in the iron ore industry for at least 15 years. At present, more than 60 units are in operation in Western Australia. The advantage of this technology is their capability to produce three products with one equipment – iron ore concentrate, iron ore middlings for further processing and slimes (tailings). The principal of this beneficiation process – upstream classification and upstream separation – will always remain. However, the optimisation of the classification and separation efficiency of the equipment itself is a continuous process driven by enhanced automation and instrumentation, design changes and the use of upstream and downstream information and requirements. Besides efficiency, the safety, maintenance and replacement conditions are very important subjects for the operation of an iron ore mine. The aim of this paper is to present a new allflux® upstream classifier design, which has been developed together with several iron ore producer from Western Australia. The new design benefits from its sustainability approach by dividing the entire equipment into small reusable parts. As a result, maintenance is minor, replacement much faster, lifetime much longer and costs much lower. Furthermore, it demonstrates new features to prevent hazardous working conditions such as confined space as well as new fixing devices to speed up the replacement of certain items and parts.

Sep 18, 2023

By J Santana, V Ferraz, G Pinto, G Cruzado

Morro Agudo is an underground zinc and lead mine owned by Nexa Resources. The mine uses room and pillar as the main mining method. The recovery of pillars as well as the opening of new excavations using sublevel stoping as mining method has been studied. On some occasions, the need to recover pillars and open a stope by using the sublevel method happens in a region that is already excavated or in deeper areas than those mined so far. These changes represent a major geotechnical challenge due to the complex openings of the mine and interaction between two different mining methods. Historically, geotechnical mapping, kinematic analysis and a 2D numerical model were used to evaluate the new mine openings, and in 2021, 3D numerical model was introduced, which enabled global and local assessment of new excavations impact and the stability of openings after recoveries. The 3D model, made with MAP3D, is used to evaluate each pillar to be recovered, considering the spans of the resulting openings, the ideal sequencing of removal to maintain stability, in addition to the impact and geometry of the pillars left in the chambers. Pillar recoveries done in 2021 and the impact of it on the pillars left were the sources of the back analysis to calibrate parameters inputted on numerical model to assess recovery on new chambers and Phyllite has been considered into the model and it has been a source of instability due to its parallel position to roof of room and pillars and stope hanging walls.

Nov 29, 2022

Australian continental crust has accreted and consolidated by thirds: 1/3 during Archean time, 1/3 during Early to mid-Proterozoic time, and 1/3 during latest Precambrian to mostly Paleozoic time. The progression of orogenic systems and the crustal consolidations they represent seem not fundamentally different in basic orogenic processes from better known Mesozoic-Cenozoic examples in that accretionary, continental margin, collisional, and intraplate intracratonic inverted and/or reactivated systems are all recognizable in the tectonic evolution ofAustralia.

Jan 1, 1995

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014