Search Documents

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A F. von Wielligh, M Scott, L Keeney

Operational Grade Engineering (GE) is the early (pre-processing) discard of low-grade mineralised and/or barren rock to improve the ore grade and/or reduce deleterious elements within the run of mine ore to be processed. GE activities generally have an impact on primary and ancillary mining activities, equipment utilization and overall equipment productivity. By discarding material which would have reported as ore (in a non-GE mine plan) means that GE must increases the total ore and total rock mining rate requirements to sustain mill feed targets. One challenge of GE and the planning of GE activities is that there are several indirect parameters which impact operational productivity. Modelling these potential impacts and determining if they can be overcome with alternate mine sequences, equipment application or possibly a different equipment fleet altogether is a key question requiring investigation. Overcoming these potential productivity obstacles associated with a more complex operation by introducing new operational parameters and destinations for ore and possibly sub-grade blocks, requires a GE mine plan that is coupled with detailed equipment productivity metrics and a sound operational plan incorporating all GE infrastructure requirements. Several GE mine plans and equipment productivity models indicate that mining rates generally need to increase by approximately 5% to 15% to sustain mill targets and often negatively impact equipment unit productivity metrices through increased cycle times, additional queuing and destination changes. These changes to productivity metrics are however offset by step change increases in asset value. This paper details a methodology to develop GE mine plans that incorporate equipment modelling, flexible mine sequencing and equipment-based production scheduling. In addition, the paper will outline impacts of GE planning on equipment unit productivities through worked examples and models.

Nov 10, 2020

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By T Roesch, M Neurohr, S Stratton

"Dwindling commodity prices are forcing today’s mining operations to increase output. Sometimes the solution is to upgrade the existing infrastructure; however, in most cases it has to be achieved with the same or reduced workforce and with the same equipment capacity through improved process efficiency and higher uptime.Measure, Manage and Improveis the mantra for this years’ Mill Operators’ Conference and while this in most cases relates to the above process efficiency, Siemens has set its focus on the availability and uptime aspect since unscheduled downtime is one of the biggest threats to any grinding operation. Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared trains, as well as long-term changes in the condition of the mechanical components or structures and auxiliary systems in gearless systems are the main reasons for unscheduled downtimes in today’s mill drive trains. Our paper outlines the efforts that have gone into adapting conventional condition monitoring methods in conventional, pinion driven mill drive trains as well as gearless systems to capture the gradual deterioration of wearing parts or structural changes in the drive train not only on fixed speed application but also on variable speed applications with multiple operating points. The paper further explores the use of condition monitoring systems as a tool to assess spare thermal motor capacity to potentially push equipment beyond its nameplate rating, along with the process that was followed to correlate measured frequency spectra and envelopes to ambient and load data to understand the kinematics of the drive train.Citation:Neurohr, M, Stratton, S and Roesch, T, 2016. Advancements in Condition Monitoring on Mill Drive Trains for Proactive Maintenance and Early Fault Detection Purposes, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

By V Louchnikov

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in situ stresses and associated seismicity with potential rock burst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in Australian underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanised installation of a chain-link mesh as trialled at Golden Grove, a base metals underground mine in Western Australia. A purpose-built mechanised roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilising the hydraulic circuit normally used for the feed arrangement.A number of operational benefits have been identified during the trial, the main two being:•improved safety of underground personnel due to the reduced amount of manual handling, and•increased productivity due to the decreased cycle time (the trial suggests a 40 - 50 per cent reduction in time over the weld mesh installation method).Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rock burst prone conditions, the operational upsides recognised during the trial imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support.

Mar 21, 2011

By P Thompson, B W. Atkinson

Water treatment is not æcore businessÆ for mining companies.Just as mineral ores and coals are unique, each requiring detailed characterisation and pilot-testing to determine their optimum beneficiation route, so too are mine waters, each requiring careful assessment to determine the most appropriate treatment. There are many cases of æregret capitalÆ expenditure, whereby mines have installed off-the-shelf equipment only to find it inadequate for their purposes or grossly expensive and labour intensive to operate.Water may be required for potable purposes, ore processing, dust control and/or irrigation. A major driver will frequently be environmental constraints for off-site discharge. Mine water projects can become very complex, and detailed models need to be prepared and optimised to properly consider the raw water sources, the on-site storages, the on-site uses and the off-site discharges, as well as handling the residuals (by-products) of water treatment. By-products may be in the form of concentrated backwash streams or streams of elevated salt content. Careful management of the by-products is required to avoid recontamination of the source water.Regulators often drive mine owners toward reverse osmosis (RO) so that their discharges can be considered as æzero dischargeÆ in terms of potential pollutants. Such decisions need to be based on site-specific information rather than any form of æblanketÆ requirement. An analogy is that many humans like to consume mineral water rather than ænormalÆ tap water. Receiving environments also accommodate or even prefer their æmineralsÆ and so RO is neither warranted nor sustainable in many cases.This paper presents two case studies for operating mine sites, both of which have a significant excess of water requiring environmental discharge. The examples demonstrate a sensible balance between treatment type, environmental constraints, process implementation and residuals management. LIMN« æthe flow sheet processorÆ was used to model one of the case studies due to the complexity of the water system on that site.CITATION:Atkinson, B W and Thompson, P, 2013. Mine water - optimising for site and environment, in Proceedings Water in Mining 2013 , pp 9-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

In May 2000, Kanowna Belle Gold Mines (KBGM) carried out a detailed Truck versus Shaft Haulage Study. The study showed that whilst the shaft option had many operating cost benefits the capital costs were too high, therefore the truck option was selected. In May 2001, the concept of achieving æshaft typeÆ benefits without the capital costs was floated. This is achieved by separating the hoisting of ore from other mining activities. The general concept is that material from underground is transported to a central location and then transported to the surface by a special truck fleet, thus removing the dependency between trucks and loaders, providing the mine with surge capacity and decreasing operating costs. At KBGM these advantages have been gained by installing an ore pass system with a plate feeder at its base that directly loads trucks. This provides the mine with a haulage system with enough surge capacity to remove the interdependency between trucks and loaders. The plate feeder is situated just off the decline which creates the opportunity to use larger more reliable, lower cost trucks. A number of truck types were considered for the truck loop including Elphinstone AD55Æs which are the truck type being used on site prior to the truck loop, CAT 775EÆs and power trailer road trains. This paper covers the philosophy behind the truck loop, the truck selection process, project installation and commissioning, people issues and the benefits expected by the operation. As of May 2002, the project is nearing completion, with decline haulage expected to commence in July 2002.

Jan 1, 2002

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By J B. Pateiro-Fernßndez, M Fuchsschwanz, G Deissmann, S Ahmad

Quang Ninh province is the most significant coal producing region in the north of Vietnam. The Nui Beo Coal Company (NBCC) operates open pit mines in Quang Ninh province and the waste overburden produced is dumped as sidehill fill in the Chinh Bac waste dump site. In the past, no special consideration has been given to the environmental impacts during the dumping operations. The mine waste is transported in trucks from the mine site to the dumping site and the loading, hauling and dumping operations are the main sources of dust emission. Rain events, especially during the rainy season, cause the generation of contaminated surface water as well as seepage of water through the dump at a number of locations. The existence of cracks at the top of the dump can pose serious stability problems with heavy rain events leading to failure of slopes which can potentially disturb vast areas of land currently used for agricultural purposes and human settlement. For sustainable development at the Chinh Bac waste dump site in the future, apart from the social and economic considerations to be assessed, there is an absolute necessity for environmental protection measures to be in place both during and after the dumping of the mine waste overburden. Research Association Mining and Environment in Vietnam (RAME) is working to develop and implement concepts for the mitigation of environmental problems emerging from dust, contaminated water and lacking slope stability to ensure successful rehabilitation of the coal mine waste dumps in the north of Vietnam. Within the framework of RAME, the Institute of Mining Engineering I (RWTH Aachen University) is managing and working to develop the stabilisation concepts for the solid mine waste dump in collaboration with the Chair of Geotechnical Engineering (RWTH Aachen University), Brenk Systemplanung and the Vietnamese group of companies VINACOMIN (Vietnam National Coal-Mineral Industries Group). The most economical and environmentally sound operations, as well as locally adaptable environmental protection measures, are essential for the sustainable development of the dumping operations at Chinh Bac dump. This paper describes the dump site and the sustainable development possibilities with an emphasis on the environmental protection and stability problems at the Chinh Bac waste dump.

Jan 1, 2009

By K M. Watling, F M, G K. Parker

Surface enhanced Raman scattering (SERS) spectroscopy at surfaces under electrochemical control has been applied to elucidate the adsorption of thiol collectors. SERS spectroelectrochemical studies at coinage metal electrodes have been carried out on ethyl xanthate and three iso-xanthates, O-isopropyl-N-ethylthionocarbamate, 2-mercaptobenzothiazole, diisobutyl- dithiophosphinate and butylethoxycarbonylthioura. For each collector, adsorption occurs via charge transfer to form a metal-sulfur bond and, in situations for which the reversible potential of the formation of the bulk phase is known, at underpotentials.

Jan 1, 2005

By A Hutton, C Dick, D Fletcher

Mine and facility closure planning is a dynamic and rapidly evolving landscape. In this landscape, mining companies and industry consultants are generally good at estimating the associated earthworks and rehabilitation costs, because it is æcore businessÆ. Through our extensive work in mine closure, we have found that the safe and cost-effective demolition of mining related infrastructure is often grossly underestimated. Or alternately, it is simply assumed that the returns on scrap steel and the sale of re-usable plant will cover the related costs. With fluctuating steel prices and no guaranteed buyer for the assets, the estimated monetary return is often unreliable and in many cases unrealistic. On this basis this logic is fundamentally flawed. We have found that on most occasions this has meant that closure cost estimates fall well short of what the actual costs are to close the mine.GSSE and Liberty Industrial have worked on over 60 mine closure projects in Australia and overseas of varying scales and across a range of commodity types. An evaluation of these projects has shown that costs associated with the safe demolition and removal of a mining related infrastructure is in the order of 20 - 30 per cent of the total cost at closure. We believe it is one of the top three risk areas associated with mine closure planning and cost estimation, alongside bulk earthworks and the capping of tailings and waste rock storage facilities.Our paper uses examples from recent projects to demonstrate all aspects outlined above. We have also endeavoured to address the following key points related to the demolition and removal of mining related infrastructure:If companies fail to plan appropriately, complicating factors such as contamination, hazardous materials, mobilisation/demobilisation, geographical location, decommissioning standards, site constraints and weather, can add considerable costs to the project and result in variations for the demolition contractor.Closure planning often assumes infrastructure that is no longer required can be utilised by a third party and/or the new land holder. We intend to show that unless adequate consultation and planning is undertaken, this is not beneficial to the mining company, the environment, or the local community.CITATION:Fletcher, D, Hutton, A and Dick, C, 2012. The æsmoking gunÆ of detailed mine closure cost over-run - A review using case studies of the real costs associated with the demolition and removal of infrastructure in mine closure, in Proceedings Life-of-Mine 2012 , pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By I Gipps

Each of us has a vision of what the future mine will be and, generally, these visions have many similarities and some differences. One of the major discrepancies in visions of the future mine is not the ultimate goal but the path to achieve it. Many of the future concepts require a radical re-thinking of how things are and will be done yet. So how do we reach this visionary future mine? We need a path that satisfies both our future aspirations of a high tech gee-whiz operated from our iPads and the unfortunately mundane approach that says ‘we must know the method works, ie nothing new’.This paper explores how, within a research based organisation, we firstly set our ultimate goal and then divide the path into realistic technology development chunks that would appeal to mining companies to progress within their organisational constraints. Through examples, such as, automated LHDs, communications systems, surveying and localisation, rock cutting and geological sensing, we illustrate how this path will get us from the here and now to the out there future.This paper also demonstrates CSIRO’s short, medium and long-term research in many of the areas needed to create the Future Mine: mining methods, automation and remote control, mine communications, mapping and mission planning, geological sensing and, importantly, human-system integration, which examines how to effectively present data as information to operators and supervisors in an intelligent and useful manner.

Nov 22, 2011

By M Doran

The Olympic Dam mine utilises 1.1 m to 1.4 m diameter raise bores for generating the initial slot void for most production stopes. Slot raise bores generally span two development levels ranging from 30 m to 50 m in height. Raise bores are reamed upward and typically leave a cap of rock equivalent to two times the raise bore diameter on the drill level (minimum 3 m). This provides safe access over the cap for subsequent production activities. It is therefore critical to ensure robust falling object protection for personnel accessing underneath, and in the vicinity of the raise bore void on the lower level. Recently, a number of mesh failures have occurred at Olympic Dam as a result of falling rock from the underside of the cap and raise walls. In addition, as Olympic Dam transitions to deeper and more challenging ground conditions, rockfall-off onto the raise bore protection mesh is anticipated to increase in frequency. This paper discusses the evolution of raise bore protection mesh used at Olympic Dam and presents results from recent site-based drop testing. This impact testing was carried out using a built for purpose object to replicate point loading and shear failure of mesh wires. Testing was also carried out on an improved mesh design which utilises two layers of Geobrugg high-tensile MINAX mesh. Results from the drop testing suggest an improvement in performance of the raise bore protection mesh is realised with the updated design.

Mar 29, 2023

One of the earliest and continuing challenges in driving sustainable development in large scale resource industry projects is around the issue of assessment û how do you measure the sustainability of a mineral operation? One of the key road blocks when confronted with this challenge is the temptation of technical folks to reach for a definition of sustainability or sustainable development. But definitions, by definition, have boundaries and limitations that serve to constrain thinking û they limit the thinking of what we can achieve with sustainability (it also acts as a barrier that constrains innovation). Rather than seeking definitions, better understanding of the core perspectives around sustainability and their application to the minerals industry provides a much more powerful platform from which to conduct assessments. But it is only when these perspectives are combined with the right framework and supporting techniques that the complex becomes doable. With the support of the perspectives and the framework, various assessment and measurement methodologies can be used; the challenge is communicating to stakeholders the sustainability character of the project in ways that are meaningful and to which people can connect. Assessment is not about finding the best or most accurate methods that fulfil strictly academic and possibly abstract requirements. The challenge is to help people understand what the impacts are, and what the value contributions will be, in a format and language that make sense in their world-view.

Jan 1, 2009

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By D J. Brake

There are many sources of gas in underground mines including development and production blasting, strata gases, spontaneous combustion, diesel equipment, chemicals used for a wide range of functions, welding activities and fires.It is only in relatively recent times that electronic gas monitors (or detectors) have become both safe and affordable for routine use.In modern mines, gas monitors should be in daily use by the ventilation department as well as blasting re-entry (or clearance) crews, and are often used by drilling crews, shift supervisors, hygienists and mine rescue or fire fighting crews.When first released, electronic gas monitors needed to be sent off-site periodically for calibration at a suitable accredited laboratory. Between calibrations, their accuracy was unknown. More recently, ‘bump testing’ and field calibration has become possible on the mine site, improving both reliability and safety as well as reducing the total number of gas monitors that need to be in use.There has been almost an overwhelming increase in the number and sophistication of gas monitor features in recent years. This paper reports on a case study into the key criteria that ventilation practitioners should be aware of with respect to the specification and selection of the most recent gas monitoring systems, and recommends good practice for site-based operation and calibration.CITATION:Brake, D J, 2015. Specification and selection of hand-held gas monitors (detectors) for underground mines, in Proceedings The Australian Mine Ventilation Conference, pp 143–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015