Search Documents

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

By J J. Moreno, J Willis, P Garvey

Many of the tailings storage facilities (TSFs) in Australia are upstream raised facilities for which the consolidation of the hydraulically deposited tailings is essential to the stability of the TSF. While much operational consideration is given to limiting the rate of rise of TSFs through careful management of deposition rates to achieve desired consolidation, the rate of embankment raise construction (RoC) is often not given the same level of consideration. Loading the tailings at too high a rate during construction could lead to upstream and potentially downstream failure of the embankment. The Tailings Retention System (TRS) at the BHP Olympic Dam Mine comprises upstream raised TSFs that are continually raised with a zoned embankment. Improving on 20 years of successful embankment raising, there was a desire to understand the acceptable RoC under varying operating conditions and assess upper construction limits to improve operational risk management. To understand the RoC, trial embankment raise construction pads were constructed at different rates and the pore pressure response of the underlying tailings material was monitored. The pore pressure data were used to calibrate the permeability and consolidation characteristics of the tailings in a finite element model (FEM) that replicated a typical embankment raise. The rate of material placement, location of the phreatic surface and construction load were varied in the FEM until failure was initiated. The results were presented as a period (in days) over which the various zones for the embankment raise could be safely constructed. The results indicate direct sensitivity to the depth to the phreatic surface prior to commencement of an embankment raise, as well as the point of application of the construction traffic load. This paper presents the study approach, challenges experienced in modelling the construction methodology, the study results and their relevance in the improvement of understanding of RoC at the BHP Olympic Dam TRS.

Jul 1, 2021

By V Lishchuk, C Lund

"Geometallurgy aims to improve resource efficiency by creating a spatial model of an orebody in order to forecast ore processing behaviour. This enables calculation of the economic value of each ore block and the use of this information for production optimisation and hence an improved economic return. Modelling uses different approaches to link geological information with mineral processing: traditional approach uses chemical elements; proxy approach – small-scale geometallurgical tests; and mineralogical approach – minerals.A geometallurgical model is obtained during execution of a geometallurgical program encompassing the entire value chain of ore processing. Available methods for establishing a geometallurgical model are in many cases limited and not yet comprehensively validated. Some of the limitations include: sampling density, assaying methods and quality, forecast accuracy block model content, geostatistical solutions for non-additive components, blending and assessment of positive impact of geometallurgy on the project. Synthetic ore models combined with process simulations and production scheduling, based on strong case studies, present a viable way to address these shortcomings. Such synthetic ore models will have realistic elemental and mineral distribution, textural attributes and 3D variability for input into the design of an appropriate geometallurgical program.A synthetic orebody was created for an apatite-bearing iron deposit. Variability in modal mineralogy was described by geostatistical parameters combined by a set of linear and trigonometric functions. The generated synthetic deposit model was used to develop a mine production plan to generate a simulated process feed. The process feed had detailed information required for beneficiation process simulation: modal mineralogy, chemical composition of minerals, grain size and specific gravity. The synthetic system was used to measure benefits that a geometallurgical program developed for real cases could provide, compared to production where only head grade is optimised. These include a reliable sampling strategy and confidence in the feed-quality forecast for economic evaluation.CITATION:Lishchuk, V, Lund, C and Lamberg, P, 2016. Development of a Synthetic Ore Deposit Model for Geometallurgy, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 275–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By R Bertuzzi

"This paper presents preliminary results of ongoing research being carried out at the University of New South Wales Australia (UNSW) into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that rock mass strength can be determined following the geological strength-index (GSI) approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions: construction dates from 1880s to 2006 spans from 3.2 to 12.5 m depths from 17 to 124 m excavation methods of drill and blast, roadheader and tunnel boring machine (TBM).Finite element modelling is used to assess the likely magnitudes of the principal stresses that were present at the time of the failures. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zones. Failure and stable points are then compared to the proposed strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown and the spalling criteria. The ability of the Hoek-Brown rock mass strength criterion to differentiate between the ‘failed’ and ‘stable’ zones is considered to be remarkable.CITATION:Bertuzzi, R, 2014. Estimating the rock mass strength of Hawkesbury Sandstone, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

Carbon sequestration in planted forests provides an immediately available, low cost option to address the greenhouse impacts of coal mining and coal utilisation in a carbon constrained world. In addition, planted forests also offer the opportunity to address other environmental issues, particularly salinity and loss of biodiversity. Given salinity is characteristically associated with agriculture in the 500 to 700 mm rainfall belt, then where such forests can also produce commercial timber products, they offer the additional opportunity to establish new, diversified rural employment in both timber growing and processing. In the majority of Australian catchments affected by salinity, where rainfall is generally less than the 700 mm limit to conventional forestry, and where groundwater reserves are often saline, the objective of achieving economically viable forestry production presents a significant challenge. In 1996, Saltgrow commenced a collaborative breeding program to combine the salt and stress tolerance of E camaldulensis, with the growth rate, stem form and wood properties of the commercial species, E grandis and E globules. This program aimed to produce trees with the potential for commercial rehabilitation of saline landscapes. Results covering a range of site conditions from SaltgrowÆs network of over 100 trials around Australia are presented. The opportunity for commercial plantations integrated with agriculture in low to medium rainfall areas to address salinity and sustainability will be discussed. In addition, the significant potential for partnerships between land-rich, cash-poor farmers, catchment management authorities seeking to invest in public good projects that enhance environmental sustainability, and major carbon producing industries with either mandated or voluntary requirements to curtail net emissions will also be discussed.

Jan 1, 2005

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

By S J. Clarke, G Sieders

Double corrosion protection (DCP) rock bolts have evolved to become complicated assemblies comprising numerous components. This complexity is mainly associated with durability considerations including potential exposure to adverse groundwater conditions and ensuring separation of dissimilar metals within the bolt assembly itself.Recent progress in the construction of glass-fibre reinforced polymer (GRP) rock bolts have the potential to provide a viable alternative to conventional steel rock bolts in civil tunnelling applications. The durability of the material results in a much simpler bolt detail and permits the use of resin rather than solely cement based grouts.This paper presents the findings of the comparative structural testing of GRP bolts with conventional DCP steel bolts. The axial load performance, including stiffness, ultimate capacity and ductility of bolts are compared. Shear behaviour of bolts is considered, including durability issues associated with damage to the plastic sleeve used in DCP bolts.The paper also considers other issues which are relevant to the design of temporary and permanent rock bolts used in tunnel support, such as initial tensioning and grouting. Long-term performance, including durability and creep are also reviewed.CITATION:Clarke, S J and Sieders, G, 2014. Comparison of glass-fibre reinforced polymer rock bolts with double corrosion protection steel rock bolts for use in tunnel applications, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 237–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J MacNeil, R Dimitrakopoulos

As open pit mining of a deposit deepens, the cost of extraction may increase up to a threshold where transitioning to mining through underground methods is more profitable. This paper provides an approach to identifying an optimal depth at which a mine should transition from open pit to underground mining. The value of a set of candidate transition depths is investigated by optimising the production schedules for each depth’s unique open pit and underground operations. By considering the sum of the open pit and underground mining portions’ value along with the cost of transitioning corresponding to each candidate transition depth, the optimal transition depth can be identified. The optimisation model presented is based on a stochastic integer program that integrates geological uncertainty. As an input, the stochastic integer program utilises a set of several stochastic simulations that represent equally probable scenarios of the mineral resource. This group of simulations describes the uncertainty in the deposit, while the optimiser aims to maximise value based on discounted profits of both the open pit and underground components of the deposit.CITATION:MacNeil, J and Dimitrakopoulos, R, 2014. A stochastic optimisation formulation for the transition from open pit to underground mining within the context of a mining complex, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023

By J Rola

This paper outlines a laboratory-based design method, founded in critical state soil mechanics, for identification of an appropriate compaction specification to ensure dilative conditions prevail across the design TSF stress range. The method makes use of the critical state line (CSL) and consolidation tests prepared at varying compactive efforts. The CSL and consolidation curves are plotted together in e-log p’ space, with the compaction curves transformed from vertical effective stress to mean effective stress using the coefficient of earth pressure at rest (K0). Consideration is given to the sensitivity of K0 as it is generally not available during the design phase. An example of the design method is illustrated with laboratory data.

Jul 1, 2021

By B Broad

"Establishing ventilation in the early stages of a new mine is an essential step to achieve scheduled outcomes that ultimately drive the financial success of an operation. If the primary ventilation is not in place in time to support a contractorÆs work output, then the ore delivery is likely to be severely impacted. Options to increase ventilation in order to address shortfalls are limited. This in turn can lead to reduced revenue generation at a time when a mine is at its highest capital outlay. This can have implications for any company, but even more for an explorer moving to producer. The ventilation put in place to cover the start-up period is also unlikely to cover any extended or increased load required to meet schedule delays.The following paper examines two issues in relation to ventilation with a focus on small to medium projects where the company is establishing a mine using a mining contractor. The issues being: potential impacts on the contract and tender process when using a mining contractor key mine design considerations, such as æcrunch timeÆ, as they interact with ventilation achieving a successful ramp up.A recommendation is made for higher levels of detail around secondary ventilation leading up to the primary fan installation. The information should be included as part of the tendering process and preliminary project execution planning. Understanding the æcrunch timeÆ concept can lead to strategies, as well as back up plans, to minimise any negative impact.By understanding key risks around primary ventilation establishment for a new mine, detailed design work can be completed where it is needed most. Value is added by reducing uncertainty and a payback with better contract terms and a more robust ramp up plan. This will improve the economic return for the company and reduce the risk.CITATION:Broad, B, 2013. Contract considerations and other critical ventilation aspects in achieving a new mine ramp up, in Proceedings The Australian Mine Ventilation Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

The Emmaville district is located in the northern part of the New England region of New South Wales some 400 miles north of Sypney. Better known for its substantial production of tin and tungsten ores, the Emmaville district has also been the centre of a small and somewhat sporadic production of copper, arsenic, silver, lead and zinc. This production has come principally from three mines-Webb's Silver Mine, Webb's Consols and, to a lesser extent, Pye's Creek Silver Mine.The ores from these mixed sulphide deposits are texturally and mineralogically complex and the problems of beneficiation are rather formidable.GENERAL GEOLOGYThe main rock type of the Emmanville district is a dark, brown to blackish massive siltstone of Permian age which overlies acid volcanics possibly also of Permian age. In places the siltstone gives way to conglomerates and standstones with discontinuous lenses of calcareous sediments (David, 1887).The whole series is folded but because of the massive character of the more expansive siltstone, detailed structure is difficult to delineate.Toward the close of Permian time the area was intruded by a series of intermediate to acid plutonic and hypabyssal rocks. Mineralization within the region is ascribed to the more acid of these intrusives-granodiorite, granite, and quartz-felspar porphyry (Lawrence, 1957, 1960).No intrusive rocks outcrop in the immediate neighbourhood of Webb's Silver Mine though granite occurs two miles...

Jan 1, 1961