Search Documents

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

By Sans H

The geostatistical Discrete Gaussian (DG) model is demonstrated to be capable of providing an effective means of implementing change of support for Enterprise-style mineralisation and thus providing reliable global recoverable resource estimates. At Enterprise, sample grade distribution proves to be highly positively skewed, therefore significant deskewing of the histogram and reduction of variance occurs when going from sample to block support. The DG model was experimentally tested in'the Southern Primary Zone (SPZ) at Enterprise, where high anisotropy ratios and pronounced short range structures are observed in variograms. The experimental test was run for a change of support for which the variance reduction was. approximately 60 per cent. This reduction is similar to that predicted by Krige's Relationship ('the volume-variance relationship') for the practical situation of a change of support from 5 m vertical blasthole samples to 3 m x 8 m x 5 m selective mining unit (SMU) blocks. The DG model was found to correctly predict the grade tonnage relationships for a wide range of cut off grades. The experimental test indicated that, given a representative histogram and variogram, the DG change of support provides a computationally efficient and practical means of reliably assessing global mineable resources at the early stages of a mining project. Further, it allows a range of selectivity strategies to be meaningfully and comparatively considered prior to mining.

Jan 1, 1995

By M.J. Mitchell

Platinum-group minerals (PGM) are recorded from a number of localities along the Waiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of "platinum" were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS)and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni. R^~

Jan 1, 1995

Pasminco is actively addressing the optimal utilisation of the known orebody at the Broken Hill mine, in addition to actively exploring for economic mineralisation in the region. As part of the policy of better utilising the known mineralisation a major upgrade of geological systems at the mine was initiated. The software chosen for this change was Maptek's Vulcan, mainly because of the ease of use of this package. Rather than having numerous data sources in varying software packages the mine aimed to limit interfaces and packages. The decision to upgrade the mine's software was not taken lightly, especially in view of the inature stage of Broken Hill mining operations. However, the current mine life of Pasminco Broken Hill mine is I I years, which is longer than many new mines setting up in Australia today. Also, a more sophisticated system brings with it a better understanding of the economic mineralisation, possibly extending the mine life further. The process of moving the Broken Hill databases into Vulcan was a huge task which included, database transfer, digitising, wire framing, modelling and eventually ore resource calculation. To ensure the validity of the new ore resource accounting system, the existing system was run as a duplicate for the introductory year, providing a comparison and if necessary a safety net. The benefits of such a change, however, became apparent almost immediately. Area geologists realised the opportunity to revise geological interpretations in their areas of responsibility, enabling them to obtain a better understanding of orebody morphology. Three- diniensional analysis provides an excellent method by which review of ore targets both in the underground and mine lease exploration areas can he made. As each new find of mineralisation enters the system and hopefully extends the mine life, the opportunities for further mineral exploration in Broken Hill area by Pasminco are enhanced.

Jan 1, 1997

By Y M. Lee, Y Hong, B C. Kim

Since sintered ore is the primary source for producing molten iron in the blast furnace process, maintaining stable quality despite the utilisation of low-grade iron ore is crucial. However, conventional analysis methods, such as chemical composition, ore size distribution and types of iron ore, have limitations in developing the utilisation of new low-grade iron ore and predicting sintered ore properties. Sintered ores are formed through a complex melting process of granule particles consisting of iron ore, flux and fuel. Consequently, it has been investigated that analysis methods which apply the reactive properties of iron ore to predict sintered ore characteristics. In this study, we estimated the properties of iron ore by simulating the assimilation process of coarse ore, which influences the bonding strength of sintered ores and quantifying the degree of assimilation reaction. Pseudo particles were formed by granulating coarse ore (1–3 mm) with adhering fines, which act as primary melts and sintered at 1623 K. The bonding strength of individual sintered ores, formed from 11 different types of iron ore, was measured using a simplified Tumbler Index (TI) test and each value was indexed as the Iron ore Reactivity Index (IRI). By investigating the relationship between the degree of assimilation depending on iron ore properties and the characteristics of sintered ore, we demonstrated that sintered ores formed from more reactive iron ore exhibited stronger bonding strength. Moreover, when blending conditions resulted in a higher Iron Blending ore Reactivity Index (IBRI), the physical properties of sintered ore improved. The development of this analysis method is expected to not only enable careful consideration of iron ore usability but also allow for the advance prediction of sintered ore qualities by deriving the IBRI.

Sep 18, 2023

By Merwin RA

The recent development of rare earth permanent magnets has revolutionised the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focusing on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

The operation of cyclones and cylinders is briefly described and com- pared, and a number of recent applications in mineral, gold and coal plants discussed. The capacity of an existing pump and cyclone in a circuit can be sig- nificantly increased by retrofitting a cylinder in series to predensify the cyclone feed. The cyclone overflow product size can also be adjusted and controlled using a variable aperture valve between the cylinder and the cyclone. This predensifier-cyclone system has been used at plant scale to con- trol the pulp density of the feed to cyanidation in gold plants, to size flotation feeds before split conditioning and to deslime and classify in gravity plants. Application in a typical regrind circuit is considered. Cylinders and cyclones also have numerous applications in water management systems, e.g., degritting mine and plant waters to protect pumps, sprays and other equipment. Screen undersize and flotation con- centrate dewatering circuits are described to illustrate how suitable stream recycles can reduce water consumption, optimize fresh water use and improve efficiency.

Jan 1, 1988

By B J. Beven, A Harris, L Balzan

Fortescue Metals Group flagship operation, Cloudbreak, is located in the Pilbara region of Western Australia. The mine is capable of delivering an annualised production rate of 40 Mt/a. Positioned 50 km to the east of Cloudbreak is Fortescue’s Christmas Creek operation, which has a combined processing capacity in excess of 50 Mt/a. Following on from these successes, Fortescue advanced development of its western Pilbara mines at the 60 Mt/a Solomon Hub. These processing installations place Fortescue in a strong position to deliver on a guidance of between 155–160 Mt/a for financial year 2014/2015.As Fortescue enters a phase of asset consolidation and debt repayment over expansion, the business is commanding stronger performance through enhanced plant operating practices and mine site cost reduction initiatives. To this end, the strategic placement of instrumentation is an area being given greater consideration. Access to real-time information pertaining to conveyed materials is of major interest to operators for making timely process control decisions. Fortescue has recognised the importance of accurate and up-to-date process information about their ores and hence, has adopted the use of Scantech’s Geoscan mineral analysers at two of their mines.There are two Geoscans at Cloudbreak; one on the ROM feed conveyor and another on the final product conveyor. These allow the in-feed material grade characteristics to be assessed. Moreover, the final product stream can be monitored to ensure product quality is maintained within acceptable quality tolerances. A third Geoscan is installed at Christmas Creek mine on a conveyor that transfers final products to Stockyards.This paper discusses the use of the Geoscans in these installations, including benefits to Fortescue’s operations, as well as functional considerations such as the impact of maintenance and calibration. A discussion of recent advances by Scantech is provided including enhancements to the calibration process and minimising plant downtime, along with a summary of results obtained.CITATION:Balzan, L, Beven, B J and Harris, A, 2015. Geoscan online analyser use for process control at Fortescue Metals Group sites in Western Australia, in Proceedings Iron Ore 2015, pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C Laming, S Staude, D Hammond, S Sheppard, J Griffith, S Stanfield, S Marriott

Long Operations is located on the eastern slope of the Kambalda Dome in Western Australia. Kambalda hosts nickel deposits that are modelled to have formed from an exsolving sulfide melt from a parental komatiite melt. The nickel deposit model predicts a stratigraphical relationship where massive Fe-Ni-Cu-sulfides are deposited in troughs at the base of komatiite channels. The basal contact of the sulfides is generally tholeiitic basalt. The Kambalda geological sequence form a dome structure with a granodioritic core and have undergone tectonic and metamorphic overprinting, resulting in the formation of upper greenschist to lower amphibolite-facies units.On the basalt-ultramafic contact, within the Long Operations, there are two separate channels hosting seven different orebodies. The Moran orebody is the most undisturbed orebody at Long Operations, with many primary magmatic textures preserved, making it ideal for studies to improve the existing nickel sulfide formation model. Detailed exploration and production infill drilling and systematic sampling indicates consistent nickel tenor variations over the entire Moran orebody. This was also observed in other deposits in Western Australia and was explained as metamorphic variations. Similar variations are observed with some trace elements that cannot be explained by metamorphic overprint but with gravitational segregation in the liquid sulfide. Other more complex trace element patterns (eg Cr) require additional explanations and are partly originated from incorporation of underlain basalt and sediment and partly from gravitational segregation.From a mining perspective, the Moran orebody can be used as an example of modern high-speed mining, but at the same time preserving samples for the future and allowing knowledge from the geological context and geochemical signatures to improve future exploration.CITATION:Staude, S, Marriott, S, Griffith, J, Laming, C, Hammond, D, Stanfield, S and Sheppard, S, 2014. Improvement of existing ore-forming models due to systematic sampling during mining – an example from Kambalda, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By P M. Hetherington, M P. Murphy, K E. Crook, F Pym

Resource characterisation is critical for informed decisions in both strategic and operational space. The sources of information for resource characterisation are limited by: direct measurement of resource attributes, such as grades, rock-types, mineralogy, and are available only from sparse locations, ie drill holes; or indirect geophysical measurements such as seismic, gravity or electro[1]magnetic survey. Data collection tools, methods, and processing technologies are constantly improving providing a broad spectrum of options for data collection strategies. The cost of each data survey varies from thousands to millions of dollars with the value of each additional data having diminishing return for a particular business decision. The value of information analysis provides the optimal decision on data collection strategy within a limited available budget. This work presents an example of value of information analysis for new Blast Hole Assay Tool (BHAT) and Reverse Circulation Grade Control (RCGC) data used in addition to the wider spaced exploration data. The value of information is quantified in terms of reduction of grade uncertainty, ore loss and dilution by comparing different combinations of data collection methods. Four different strategies were considered: exploration samples in addition to 50 per cent of blastholes surveyed with BHAT, exploration samples in addition to 33 per cent of blastholes surveyed with BHAT, exploration with wide-spaced RCGC data, and exploration without additional grade control. For each strategy the observed values have been simulated using advanced multivariate geostatistical simulations and compared with simulated ground truth models. The calculated uncertainty, ore loss and dilution informed the optimal data collection strategy. Opportunity to reduce sample density from the nominal 50 per cent of drill holes was evaluated.

Mar 22, 2022

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

The past decade hap seen revolutionary advances in com-munications and information-handling techniques which have been stiriulated by "cold war" military requirements and by, current programmes for probing into outer space: The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration, methods. These are (1) The development of new approaches, based on information theory, for extracting signal from noise more efficiently than before, and (2) The use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered NR. Complex playback and other data processing facilities have been developed to apply these approaches.

Jan 1, 1963

This study examines the application of Landsat TM data to the identification of hydro- thermal alteration in the arid terrain of the El Salvador region of north Chile. Numerical reflectance values were extracted from the digital Landsat TM data for a variety of rock surfaces, including four parts of the El Salvador gossan, for each of six spectral bands. These reflectance values were analysed statistically in order to select the three spectral bands, combined as a colour composite image, that are most efficient in discriminating different varieties of alteration and for general geolog- ical interpretation. The most cost effective com- posite image for this area is a combination of bands 1,4 and 7 as the blue, green and red components respectively, with simple contrast enhancement. This image is superior to some much more expensive enhancement techniques and allows unambiguous identification of areas of hydrothermal alteration larger than about 50m. The display includes a practical guide to the use of Landsat TM imagery for volcanic gold Exploration.

Jan 1, 1987

By Lacy JC

Human habitation of the Pacific Rim began when mankind began migrations out of its place of origin in the Rift Valley of Central Africa c. 4million years ago. This migration was erratic and largely controlled by advances and retreat of the various Ice Ages which, while limiting advances in areas of intense cold, at the same time aided migration thro-ugh the creation of land bridges as ocean levels declined during periods of glacial advance (Fig.l).Mankind began its trek to the Pacific from Africa across India then north into southern China and south into Indonesia (Fig.2). In part, these migrations stimulated early technological develop-ments to fulfill needs and adapt to environmental conditions; thus, these nomads developed stone and bone tools, animal skin clothing and the use of caves and other simple shelters. The earliest evid-ence of mankind's use of fire can be found at Zhou-koudaian near Beijing, c.400,000 BP.From China, the completion of the Pacific Rim's population can be attributed to the last Ice Age that dropped the ocean level by more than 300 feet and created land bridges about 40,000 BP allowing migration across the Bering Strait into Alaska and to Australia from Indonesia. The American migration reached Mexico about 30,000 BP, and by 6000 BP the occupancy of the Pacific Rim was complete when the first human settlers reached the southern tip of Chile.

Jan 1, 1990

By T Wambeke, J Benndorf

A risk-robust development of a heavy mineral resource requires an assessment of the geological uncertainty and spatial variability of the key factors impacting the mining and processing operation. Attributes of interest are the total heavy mineral grade, the slime content and the amount of oversized particles. The modelling of a mineral sand deposit presents two main challenges. Firstly, the exact location of the geological boundaries are obscure due to the complex interaction of the deposit formation processes. Secondly, the properties of interest exhibit a rather complex transitional behaviour across the so-called soft boundaries. Traditionally, the modelling exercise is restricted to a consecutive stochastic simulation of distinct geological facies and orebody properties. This results in different zones separated by hard boundaries, ignoring the typical transitional behaviour.This contribution presents an alternative approach which models the entire sand body as a single domain while accounting for the complex trends present. Error curves are used to infer covariance model parameters without the need of a prior removal of the trend. The principle is based on minimising the differences between empirical and theoretical errors resulting from two methods of prediction calculated for different rings of influence. The added value results from the unambiguous decomposition of the spatial variation into a deterministic trend and a stochastic residual. The trend model neither overfits nor underfits the data. The calculated residuals are thus unbiased and the uncertainty can be correctly assessed.The effort results in a characterisation of the resource uncertainty which provides a more realistic image of the spatial variability of the key properties in and across the geological domains of an existing heavy mineral sand deposit.CITATION:Wambeke, T and Benndorf, J, 2014. Optimal inference of modelling parameters to simulate complex trends across soft boundaries – a case study in heavy mineral sands, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 73–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N Lima, A Piçarra, L Filippov, I Filippova, M Marques, K Silva

The iron industry produces a considerable amount of tailings per annum, due to its substantial volumes of production. The actual iron ore processing routes require the removal of slimes fractions. In addition to iron oxides and quartz, the iron ore slimes are generally composed of other minerals such as kaolinite and finely dispersed iron hydroxides which impact significantly the performance of reverse cationic flotation. In this study, we propose a two stage processing route that would allow further beneficiation of iron slimes which are not successfully beneficiated, avoiding their disposal as waste. The new amidoamine reagent was tested as a collector in a two-stage route to process two samples of iron ore slimes with d50 close to 10 μm and with high kaolinite content (13 to 20 per cent). The results showed that it was possible to obtain iron concentrate with 66.5 per cent iron and 48.4 per cent mass recovery for a feed containing 48.9 per cent Fe associated with hematite (39 per cent) and goethite (32 per cent). The collector efficiency was improved by mixing with frother for the slimes with higher goethite content of 55 per cent: the concentrate grade was increased from 58.8 per cent to 64.5 per cent with addition of the frother at the expense of reducing operation metallurgical recovery from 87.8 per cent to 75.6 per cent. The efficiency of the process was improved by applying an external energy impact to disperse the fine particles and clean the surface of the minerals. The new amidoamine collector does not require a depressor such as corn starch and may provide the development of new concentration routes for complex ultrafine iron ores. The combination of the amidoamine-based flotation at first stage with high intensity magnetic separation allowed development of optimised two-stage processing routes to valorise the iron ore slimes rejected to the tailings in the actual flotation plant.

Sep 18, 2023

By J M. Santini, I C. A Streimann

Arsenic is a naturally occurring element in the environment and is toxic to biological systems. Arsenic can exist in the environment in the following redox states, arsenite (+3), arsenate (+5), arsine (-3) and elemental (0) (Oremland and Stolz, 2003). Arsenic is released into the environment by natural and anthropogenic activities such as rock weathering and ore mining, respectively. Such activities result in the release of the soluble inorganic arsenic oxyanions, arsenite and arsenate. The redox state of arsenic in the environment is influenced by a number of factors including, redox potential, pH and microorganisms (Irgolic et al, 1977; Genc-Fuhrman, Tjell and McConchie, 2004). Recently, the ability of microorganisms to influence the cycling of arsenic in the environment has attracted much attention. Microorganisms that can oxidise arsenite and reduce arsenate have been isolated and the mechanisms of arsenic metabolism are currently being investigated. The differences between arsenic resistance and arsenic metabolism are being revealed. The role of microorganisms in the release of arsenic into the environment is of particular importance with arsenic contamination of waters causing the death of millions of people worldwide, due to the consumption of contaminated water (Vasken Aposhian et al, 2003; Islam et al, 2004).

Jan 1, 2004