Search Documents

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

Mine pit slopes in the Pacific Rim are a geotechnical challenge because of the complex geology in which they are developed. Mines are currently being fast-tracked to meet the increase in commodity prices, often resulting in some reduction in ground studies and short-cutting of design procedures. In addition, the resources boom means that skilled personnel are in relatively short supply. At a time when mine pits are getting bigger and deeper, and the engineering is getting more demanding, there is an increased demand on managers to effectively implement the work.   Experience both in New Zealand and the Philippines, display the complex range of geological environments in which pits are being excavated. Working in these conditions has shown that successful geotechnical design requires a strong geotechnical model based on sound geology. An appropriate level of investigation and analyses results in a certain level of understanding for the mine design. There is a point where additional expenditure (on investigation and analyses) is not warranted based on the expected minimal impact on decreasing the level of perceived risk on the project. For most projects in our experience the analytical methods and complexity of geotechnical assessment changes increases as the level of knowledge grows.

Jan 1, 2006

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By Bawden WF, Paynter JT

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopcs

Jan 1, 1998

The introduction of large diameter drill holes and mass firings in underground metalliferous mines has led to an increase in the number of reported sulfide dust explosions in Australia and overseas. Adaptation of the coal mining technique of using limestone to inhibit or prevent dust explosions has not been entirely successful as the development and inhibition of a sulfide dust explosion is somewhat different from that of a coal dust explosion. Tests were carried out on two pyritic ore samples, sulfur contents of 41 and 36 per cent, in 8 and 20 litre explosion chambers to evaluate the effect of the addition of limestone on the maximum explosive pressures developed and rates of pressure rise. Significant values were obtained in both chambers with dusts containing 60 per cent ore and 40 per cent limestone. The percentages of limestone required to inhibit the pyritic dusts were considerably higher than those values generally accepted by the mining industry and the current methods used to inhibit sulfide dust explosions should be re-evaluated.

Jan 1, 1986

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

Traditionally, the Lead Lode at Broken Hill has been represented on presentation plans, cross sections and diagrams in scientific papers as a solid black mass, around which the more 'interesting' and 'structurally useful', wall rocks appear to wrap. Structural analysis of the Broken Hill orebodies has usually turned to these wall rocks to determine the structural history of the mineralisation.This tendency to represent the orebody as a massive single entity is incorrect and the aim of this paper is to illustrate that sulphide orebodies (in this case Lead Lode), are a dynamic part of the mine stratigraphy. They can preserve a great deal of useful structural information that can be recorded with detailed internal mapping.Three main categories of ore type are recognised in Lead Lode; Stratiform ores, Mobilised ores and Metasomatically altered ore. The ore types in these categories occupy or have formed in distinct structural and stratigraphic positions and have clearly recognisable inter-relationships.

Jan 1, 1993

By Teniswood CF, Sheppard I, Mason LG

An industry initiated project, sponsored by the National Energy Research Development and Demonstration Council, has worked for two years in developing design guidelines for underground coal mining machinery.Continuous miners and shuttle cars were selected for the initial development of design guidelines as these machines were linked with 7500 lost workdays and 490 reported injuries during the preceding two years.

Jan 1, 1991

By Alichurch P. D

Perseverance nickel deposit is located at latitude 27¦ 491S, longitude 1200 42'E, 330 km north of Kalgoorlie, Western Australia. Gossanous outcrops were discovered in April, 1971, and after further detailed surface investigations, percussion drilling led to diamond drilling by June, 1971. Up to December, 1972, 127 diamond holes totalling 45,590 m were drilled to indicate 33 million tonnes averaging 2.2% Ni using a 1% cut-off grade. The deposit occurs in a lenticular ultra- mafic unit emplaced in metasediments locally forming the eastern flank of the Archaean green- stone belt trending NNW from Leonora to Wiluna. To the east a major strike fault separates the metasediments from gneiss; westwards there is a sequence of metavolcanics with further ultra- mafic units. Length of the lens is 3500 m and it attains a maximum width of 800 In. The eastern contact is moderately regular, but the western contact is prominently embayed. Local strikes are NNW, and dips are steeply W. A set of strike faults cuts the ultramafics and enveloping quartzites. These are normal faults, parallel to the major eastern fault, dipping 65-70¦W. They impart a serrated pat- tern to the sub-outcrop of the western contact. Massive serpentinite is the dominant rock in

Jan 1, 1973

By Woodcock J. T, Zhu T, Sparrow G. J

A lead-zinc-pyrite flotation middling was pressure oxidised to give residues containing iron hydroxy sulphates (a mixture of basic iron sulphate (BIS) and a hydrated iron sulphate (HIS)) and lead sulphate. Direct thiourea leaching of this residue gave over 90 per cent extraction of gold and silver, but thiourea consumption was high (56 kg/t) because of soluble iron(M) in the residue. Attempts were made to decrease the thiourea consumption by removing the water-soluble iron(M) or reducing it to iron(II). Water washing of the pressure oxidation residue removed most of the hydrated iron sulphate but little of the basic iron sulphate. Iron removal was only 12-20 per cent, depending on the number of washes, from one sample which was low in HIS, and 40-45 per cent in another which was high in HIS. Iron extraction was not appreciably increased by using dilute sulphuric acid (with or without additions of sodium sulphite), dilute phosphoric acid, or sodium chloride solution (150 g/L NaCI). Direct thiourea leaching of the water-washed residue gave over 90 per cent extraction of gold but only 49 per cent of silver, with a thiourea consumption of 27 kg/t. However, the application of a water wash followed by reduction of dissolved iron(III) with sodium sulphite in the presence of thiourea, and then thiourea leaching resulted in over 98 per cent extraction of gold and silver for a thiourea consumption of 26 kg/t.

Jan 1, 1991

IN the present paper it is the writer's intention to largely confine the subject-matter to details relating to the metallurgical practice in connection W,ith the blast roasting of lead ores at the Port PiJ;ie works of the Broken Hill Associated Smelters Pty. Ltd. rather than to elaborate on mechanical plant details which are more or less standard equipment of the average Dwight and Lloyd or Huntington-Heberlein blast roasting installations (hereinafter referred to in the text as D. & L. and I.I. & H. respectively). The present blast roasting plant is a combination ot D. & L. straight line machines and IQ-ton H. & H. pots. The latter installation was an operating unit prior to the introduction of the D. & L. machines, the pre-roasting then being accomplished in Ropp roasting furnaces.On the introduction of the D. & L. machines the use of the Ropp roasting furnaces as a pre-roasting unit was discontinued, and this step of the process was then carried out on one section of the D. & L. installation.Consequently, then, the present plant consists of (1) A section of D. & L. machines, which operate solely as a pre-roastiIig unit. (2) A section of D. & L. machines which operate to their full capacity as 3, final roasting unit and treat the main portion of the pre-roasted material.

Jan 1, 1922

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By Nekitel S, Arumba J, Kopi G, Findlay RH

The Kainantu area lies within the composite Scrapland terrane which is composed of Mesozoic metamorphic and intrusive units, overlain by Cenozoic marine sediments, volcanic and intrus-ive units and Quaternary fluvial sedi-ments.Four deformations (Dl, D2, D3, D4) are recognised within the Mesozoic sequences, which consist of greenschist to amphibolite facies schist derived from felsic to intermediate pyroclastic rocks and pelitic sediments. The second, third and fourth fold events are present in the Cenozoic sequence, and these rocks are broken by thrusts related to northwest trending D3 folds. South-dipping, possibly lystric, normal faults are recognised and may be related to uplift and exposure of the metamorphic rocks as core complexes.Known mineralisation in the area consists of gold and copper skarn deposits, porphyry copper deposits, shear-hosted gold deposits, epithermal vein deposits and gold placer deposits. Over 35 hard rock and 18 gold placer deposits are known within the area. Of significance are the Kathnell shear-hosted auriferous quartz veins; such structurally controlled veins may be more widespread than proposed prev-iously and offer a new exploration target.

Jan 1, 1994

By T J. Scanlon

Heavy minerals recovered from recently discovered deposits in the Murray Basin are proving to be somewhat more difficult to process into saleable ilmenite products than ilmenites from existing operations. This is due to the nature of the gangue minerals present, the impurities in the valuable minerals and the size distribution of the mineral assemblages. Ilmenite product quality, in particular, can be adversely affected by any of these factors. Over the past two years the authors have been involved in assessing the potential to manufacture ilmenite products from a variety of mineral sand deposits in the Murray Basin. The steps undertaken to define the potential products and develop suitable flowsheets have evolved in parallel to the exploration efforts, in cooperation with companies undertaking exploration in the Murray Basin. A combination of an understanding of detailed mineralogy, application of magnetic fractionation and modification of magnetic susceptibility of the ilmenites has in all cases, been successful in improving ilmenite product quality. The targeting of particular ilmenites to specific downstream processes for TiO2 pigment manufacture is the most challenging aspect of this development.

Jan 1, 2001

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

By B Cope, N Hastings, D Webb

A Feasibility Study was completed in late 2002 to ascertain the risk and reward profile from the proposed deepening of operations at Perseverance Nickel Mine in Western Australia. The system and approach adopted to this brownfields extension work is outlined and the main components of the study are overviewed. In particular, emphasis is given to the integration of mine design and scheduling tools through to financial evaluation. Detailed comment is given on the ability of the system used to provide a robust project schedule complete with 3D animation. The level of importance in eliminating scheduling errors is demonstrated in relation to the reported bottom line viability of the project. It is suggested that this is an area where brownfields Feasibility Studies have lacked clarity and authenticity, leading to the creation of an unrealistic benchmark for project implementation.

Jan 1, 2003

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986