Search Documents

Effects of High Pressure Grinding Rolls on Platinum-Bearing Ores and the Flotation Response as Compared to the Conventional Ball Mill Three major PGM ore types from the Bushveld Complex of South Africa: Merensky, UG2 and Platreef were comminuted with the use of the high pressure grinding rolls (HPGR). The influence of the feed characteristics and the various operational and design features of the HPGR on energy consumption, throughput, mineral liberation and PGM flotation recovery were investigated. The test work variables included two feed top sizes of 12 mm and 6 mm, specific grinding forces ranging between 3 - 7.5N/ mm2 and zero gaps of 1.5 mm and 3 mm. The results show that the influence of the HPGR operational and design features on energy consumption, throughput, mineral liberation and PGM recovery are ore dependent. The size reduction-specific energy relationships show that the most energy efficient utilisation of the HPGR for Platreef ore was at the lower specific grinding force of 3N/mm2 and the zero gap at 3 mm. For Merensky and UG2 ore on the other hand, the most energy efficient operation was at the higher specific grinding force of 7.5N/mm2 and the zero gap of 1.5 mm. At a specific energy input of 3 kWh/t, reduction ratios (F50/P50) of 6.5, 3.8 and 10 were obtained for Merensky, UG2 and Platreef, respectively for feed top sizes of 12mm. Further application of the HPGR as a pregrinding stage to a ball mill showed a 25 - 30 per cent increase in throughput for Merensky and UG2 ore. Batch flotation tests performed on selected samples appear to indicate that ore comminuted with the ball mill had superior grades compared with that ground with the HPGR. However, Merensky and UG2 ore comminuted at different HPGR operating conditions showed distinctions in PGM recovery. Platreef on the other hand did not appear to show any differences. Therefore, this study highlights the significance of ore type and operating variables in HPGR applications with regards to energy efficiency, throughput and PGM recovery.

Sep 13, 2010

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The, Mount Charlotte orebody contains' 5,000 tons per vertical foot-Of'quartz gold ore at an estimated ore reserve grade of )just 'over' 3 'dwt. per ton, Production from it i.s plan ned at a rate of 1,000 tons per working day during 1964.

Jan 1, 1964

Some low grade South Australian iron ores were classified on the basis of their physical characteristics. Ores from Mount Christie and Billeroo are coarse grained mixed ores; Mount Christie ore could be concentrated by gravity or dry magnetic separation at 10 mesh, but Billeroo ore needed to be crushed minus 36 mesh. Ores from Razorback Ridge and Wilgena Hill are fine grained mixed ores; ore from Wilgena Hill could be concentrated by flotation, but poor results were obtained on Razorback Ridge ore. Malcolm Creek ore is non-magnetic and crystalline, and can be concentrated by flotation, but the deposit is small. Ores from Grants Quarries and Peeralilla Hill are nonmagnetic and earthy and could not be satisfactorily concentrated.INTRODUCTIONThe Geological Survey of South Australia has for several years been undertaking a systematic study of the iron ore resources of the State (excluding the Middleback Ranges) in relation to their geology, reserves, and beneficiation. As part of the latter phase of the investigation samples of the ores have been submitted to The Australian Mineral Development Laboratories (AMDL), and it was the study of these samples which provided the material for this paper.The mineragraphic and metallurgical work was undertaken by several officers of AMDL and the results are contained in unpublished reports submitted to the South Australian Department of Mines. Field data published here was obtained from unpublished reports by G. F. Whitten, Senior Geologist, Iron Exploration, of the Geological Survey of South Australia.

Jan 1, 1964

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

By Giles C. N, Loughnan F. C

Bentonites and active earths from N.S.W., previously analysed with respect to occurrence, mineralogy and physical properties have been evaluated for use as bonding agents in quartzose moulding sands in terms of green properties and behaviour both with and without coal dust for iron castings poured at 1400°C.INTRODUCTIONIn the paper by Loughnan .and See (Part I) the occurrence, mineralogy and physical properties of the fuller's earth and bentonites of New South Wales were discussed and it was shown that some of the materials approached the quality of Wyoming bentonite. In the present paper the same samples from Marulan (Bl), Boggabri (B2), Wingen (B3), Muswellbrook (B6), Swansea (B8), Dubbo (89) and Trida (Bll) have been investigated with respect to their potential value as bonding agents in compounded moulding sands. Inaddition, the -20 micron fractions of the Boggabri (B2t) and Swansea (B8t,> were recovered and the former converted to a sodium clay, in order to assesE; the beneficiation possibilities. A sample of Wyoming bentonite (S2) also has been included for comparison.GREEN PROPERTIES OF THE ARTIFICIAL MOULDING SANDSA quartzose base sand (Botany Dune) previously oven pried and screened to 1·65 mm., was subjected to a sieve ana]ysis in accordance with standard A.F.A. practice to yield a calculated' fineness number of 45. All tests were carried out on mixtures of this sand with2t per cent clay, since such mixtures were found most suit...

Jan 1, 1959

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

By Madgwick J. C

A novel, microaerobic, heterotrophic microbial leaching system for manganese dioxide is described. Mixed natural microflora were enriched by addition of sugars and crude plant nutrItIOnal supplements. Between 84 and 104 mg MnH was solubilized per gram sugar at I per cent (w/v) concentrations for fructose and galactose in the presence of 0.03 per cent w/v dried microalgae (a Chlamydomonas species). Some 42 per cent soluble manganese was dissolved by microbial action on MnO, (3 per cent (w/v) pulp density) using a 10 per cent (w/v) molasses growth substrate.

Jan 1, 1983

The Leigh Creek Coalfield is owned and operated by the Electricity Trust of South Australia to supply fuel to the Northern Power Station. To supply electricity at lowest cost, a costing and decision process that establishes the role of the Leigh Creek Coalfield in the overall system planning and operation is required. The costing is integrated in that it is based not just on a particular mine plan but on the wider need to supply a particular electrical demand. The detail costing has evolved over time from manual to main-frame computer to microcomputer techniques. Now there is a choice between fast consistent costs and a slower but more detailed and flexible costing.

Jan 1, 1990

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

The granulites and related "dry" igneous rocks tend to be passed over during exploration for metals. Preliminary data show that high trace concentrations of Cu, Ni and other metals of economic interest are common in orthopyroxene and some of the other granulite minerals. During retrograde metamorphism of granulites, pyroxenes are converted to amphiboles or phyllosilicates, and significant quantities of metals are released and become available for incorporat- ion into new mineral phases, or may be transported elsewhere. S--rich scapolite is the normal scapolite of granulites. Its retrogression to secondary plagioclase provides much S which scavenges Cu, Ni, etc., from pyroxenes undergoing retrogression, thus producing ore-fluids. A full analysis of a scapolite with 5.10 per cent S03 is given. Beryl is unstable in granulites but the rare Be mineral taaffeite (Al4Pf (Be,Fe)O3) with 5,50 per cent BeO occurs in central Australia as a pale green Tabular mineral easily confused for chloritoid in hand-specimen. Metamorphic differentiation and mobilization of primary ore concentrations are major factors controlling their post-granulite attitude and grade.

Jan 1, 1969

By A Vickerfält, J Huss, J Martinsson

The European Union has listed vanadium (V) as one of the critical raw materials for the transition to a future green society, as stated in the Critical Raw Material Act, written by Grohol and Veeh (2023). In the steelmaking industry based on V-containing iron ore, V is a possible by-product from the slag. A requirement for slags to be suitable for V extraction is a V content preferably above 8 wt per cent as V2O3 and a phosphorus (P) content below 0.1 wt per cent as P2O5. Hence, it is important to keep V in the slag phase while the P is moved to the metal phase during the steelmaking process.

Aug 21, 2024

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By P C. Couper, P C. Keall, S J. Mathews, A Francis

An epithermal gold-silver deposit is presently being developed at the Golden Cross Mine in the Waitekauri Valley, 8 km northwest of Waihi, New Zealand. Highest grade mineralisation underground is mainly confined to an elongate zone of strongly banded quartz veining on the hangingwall. Footwall veining is irregular, flatter lying, and of lower grade. Hydrothermal breccias in the ore zone may have economic grades where clasts of vein quartz are present. Jigsaw breccias, shingle breccias, and layered breccias with sedimentary type structures such as layering, crossbedding, and graded bedding have been identified proximal to, and within, quartz veins. Mineralisation in the open pit occurs in and adjacent to stockwork quartz veining.   Three alteration zones are recognised: a central silicic zone enclosing Au-Ag bearing quartz veins, an argillic zone above the stockwork zone and in the footwall of the underground ore zone, and a propylitic zone which is gradational with argillic zone. Intense shearing is confined to the less competent argillic zone.   Precious metal mineralogy consists of electrum (65% Au; 35% Ag) and argentiferous tetrahedrite, polybasite, pyrargyrite, argentite, and native silver. Pyrite is the dominant sulphide mineral. Marcasite, arsenopyrite, and rare chalcopyrite and sphalerite also occur. Oxidation ranges from a few metres in the argillic western stockwork zone to 100 m in fractured rock in the footwall of the stockwork.   The open pit contains a proved and probable reserve of 2.1 million tonne grading 3.5 g/t Au and 17 g/t Ag. The underground mine will produce 2.7 million tonne grading 7.8g/t Au and 27g/t Ag.

Jan 1, 1991

By J-M Huizenga, Q Shu, Y Lai, J Hammerli

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Baiyinnuo’er Zn-Pb deposit is a typical skarn deposit in NE China. Skarn and orebodies mainly occur between different units of the Lower Permian Huanggangliang Formation carbonates-sandstone-mudstone or within the contact between intrusions and marble. Skarn minerals are dominated by prograde garnet and clinopyroxene, and the main ore minerals are sphalerite and galena. We conducted single fluid inclusion compositional studies using laser ablation inductively coupled plasma mass spectrometry on clinopyroxene (pre-ore-stage mineral) and sphalerite and calcite (syn-ore-stage minerals). The results show that the Baiyinnuo’er fluids are distinctly different from basinal brine but similar to magmatic fluid, thereby indicating that the deposit has a dominantly magmatic origin. This interpretation has also been supported by the Cl/Br mole ratios, which remain stable (~500) in different fluid stages. The decreases for most of the elements in the fluid inclusions from pre-ore-stage clinopyroxene to syn-ore-stage sphalerite and calcite suggest that mixing with groundwater has occurred during mineralisation, with significant Zn, Pb and Ag deposition.CITATION:Shu, Q, Hammerli, J, Chang, Z, Lai, Y and Huizenga, J-M, 2015. Laser ablation inductively coupled plasma mass spectrometry study on fluid inclusions of the Baiyinnuo’er skarn Zn-Pb deposit, north-east China, in Proceedings PACRIM 2015 Congress, pp 451–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

This paper is directed at the problems flowing from Australia's capital gains tax (CGT) on the disposal of exploration and mining tenements both in Australia and overseas. It will seek to identify the issues and give some idea of the dollar consequences of decisions lacking forethought. The paper should not only be seen in the context of Australian tenements. CGT applies to the disposal of any assets by an Australian resident anywhere in the world. Offshore incorporated companies are not necessarily free from CGT risk where it can be shown that control management and control of the relevant company is in Australia. Also the disposal by non residents of Australian tenements are potentially caught by CGT. Some will ask what has taxation got to do with a valuer who merely determines the value of assets. These days no determination can be blind to the consequences. Whether the consequences can encourage a movement in value is another thing dependent upon the circumstances; but? A role of an experienced taxation consultant is to point out parameters within which associated professionals can work. The parameters will vary from case to case, but these when clearly indicated may be of help to persons such as valuers. When one comes down to it real estate salesmen are never wrong. They have a feel for the market and almost through self fulfilling prophesies achieve sales at their guestimates. Whether they could have achieved higher considerations become virtually academic in the process. Of course I am not suggesting that tenement valuers can be compared to real estate salesmen, or am I? What is the value of a tenement? Is it the DCF/NPV type of generated value based on a large number of variable factors (ie what one may call the fundamental value)? Or is it what another may pay to purchase that tenement if it were on the market at an instant point in time? How big is the market, the quality of the bidders, the size of their purses, the needs of the buyer for comfortable fit, the premiums for foreigners, the standard of the marketing, the industry intelligence level of the bidders, the obligation to farm/sell down? The list goes on endlessly. One question must be.asked-"Is a range of values acceptable for tax purposes". ie Would any tax consultant ever provide a valuation to the Australian Taxation Office that indicates three or more possible values ie

Jan 1, 1987

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

This article focuses on TurkeyÆs gold potential with respect to exploration, development and operation after 1985. Apart from TurkeyÆs geology, which offers a substantial number of volcanic-associated gold (Ag) and gold-copper (Au-Cu) projects, there are numerous other factors which make the country a favourable place for mining. Turkey has a mining history which goes back to pre-Roman times and an excellent mining code which ensures security for long-term production. In the country, the Government and local villagers are very positive and the country works extremely well logistically with excellent road and telecommunication links. The opportunities for new discoveries in Turkey are very high. Moreover, Turkey has its eyes turned west as it moves towards joining the European Community and it is no surprise that international companies believe it has got its timing as well as its partner relationship right. Newmont, Teck Cominco, BHP Billiton, Rio Tinto, Eldorado Gold, etc all have direct or indirect interests in Turkey, as do an increasing number of midtier and junior exploration companies. Turkish Koza Gold Mining is the first Au producing company of Turkey. The Eldorado Gold owned 245 t Kisladag Au deposit in Western Turkey is currently also producing Au. In the meantime Anatolia Minerals Development is advancing the 131 t resource at the C÷pler Au deposit in North Eastern Turkey. These are significant world-class deposits. Further encouragement for investment in the Au mining sector has been provided by the introduction of a new mining law in 1985. Foreign investments in the country were encouraged and have seen a rapid increase in the last two decades. Gross domestic product (GDP) growth is in excess of five per cent per annum, inflation is down from 70 per cent to single figures, the budget deficit has been cut by 40 per cent to 11 per cent and industrial output and productivity are increasing rapidly. Turkey is politically and economically stable, is a member of the European Customs Union, has a supportive mining legislation, is highly prospective and under-explored and hosts significant recent gold discoveries.

Jan 1, 2007

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989