Search Documents

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A D. Campbell

Conversion of Mineral Resources to Ore Reserves requires a multidisciplinary approach and application of a number of Modifying Factors. The Modifying Factors for mining, particularly dilution and recovery in a caving mine are complex and can be difficult to determine. Cave flow modelling software is widely used for mine planning, scheduling and forecasting metal production. However, the conversion of Mineral Resources to Ore Reserves remains a difficult and subjective process and a consistent approach to convert Mineral Resources to Ore Reserves as part of the cave flow modelling process is not published in the literature. This is due to the difficulty in estimating the Ore Reserve that remains as cave stocks at a particular point in the mine schedule, the recovered tonnage and grade of the diluting material at various stages in the mine life, as well as the Mineral Resource classification of both the recovered and diluting material that forms the Ore Reserve. The key principle of this paper is the tracking of the Mineral Resource classification in the flow model used to estimate the Ore Reserves. This is critical to defining the Ore Reserve as Proved or Probable and enabling transparency in the reporting process. An approach for dealing with mineralised external dilution in the Ore Reserve estimation process is also provided.This paper outlines the approach to convert Mineral Resources into Ore Reserves developed at the Ernest Henry mine sublevel cave (EHM SLC). The same method could be used in any cave mine and applied at any stage of the mine life. The process replaces broad-brush assumptions for the mining Modifying Factors, such as dilution and recovery, as these are determined numerically as part of the model computation. This paper explains the Ore Reserve estimation method with a worked example to enable the reader to adopt the process at any caving mine. Mineral Resource classification within the block model is embedded in the cave flow model and the flow model results used to attribute tonnes, grade and the mixed proportions of the Mineral Resource classification for material extracted from each drawpoint. This information is then used to convert planned mine production into the appropriate Ore Reserve classification. Since the flow model simulation follows the mine schedule, it can be used to predict depletion and cave stocks at any stage of the mine life, and can calculate a residual block model at the end of the mine life. The accuracy of the flow model is checked by validating the forecast ore grade and metal tonne with reconciliation data from the concentrator which is also used to calibrate the flow model.CITATION:Campbell, A D, 2017. A simple and accurate method for Ore Reserve estimation and Mineral Resource depletion in caving mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

This research was done to reduce silica from mixed hematite concentrate of Barfkar Iron Ore Sample and increase Fe grade using reverse flotation method (Depressing Hematite and floating Silica). The used sample in the reverse flotation tests was a mixture containing two types of hematite concentrates (Spiral cleaner concentrate and Slon-VPHGMS cleaner concentrate) with the percentage of 16 per cent and 84 per cent, respectively. Fe grade of two samples was 59.31 per cent and 57.52 per cent and SiO2 grade was 5.83 per cent and 6.71 per cent, respectively. After mixing, the Fe and SiO2 grade of the mixed sample was measured at 58.10 per cent and 6.20 per cent. For flotation tests, effect of variable operational parameters including feed size distribution (d80 = 130 microns and d80 = 53 microns), pulp solidity (25 per cent and 30 per cent w/w), pH (9.70, 10.20 and 11), Sodium silicate as a dispersant (500, 1000 and 2000 g/ton), Starch as a depressant (500, 1000, 2000 and 3000 g/ton) and EDA as a collector (180, 300, 400 and 500 g/ton) were investigated. For evaluating the influence of Sodium silicate and Starch dosage, initial flotation tests were performed on the main sample (d80 = 130 microns). These two parameters had no significant effects on the yield, Fe, and SiO2 grade of flotation concentrate based on test results. In the next step, screen analysis was carried out on the main sample for mineralogical studies. Accordingly, the suitable size distribution for releasing Fe and SiO2 particles was smaller than 53 microns. Therefore, the sample was crushed until d80 = 53 microns. Then, supplementary tests were performed on the crushed sample for studying the pH range, pulp solidity, and EDA collector dosage. After doing silica removal flotation tests based on the designed pattern and comparison of the results, the conditions consisting of size distribution d80 = 53 microns, pulp solidity 25 per cent, pH 10.20, Sodium silicate 1000 g/ton, Starch 1000 g/ton, and EDA 500 g/ton was selected as optimum values. In the last test, Fe and SiO2 grade was measured at 60.00 per cent and 3.93 per cent, respectively, and Fe recovery was obtained at 74.93 per cent.

Aug 24, 2022

Predicting Water Recovery from Flotation Cells

Sep 13, 2010

Nickel-bearing ores in North-east Dundas have been described by A. McIntosh Reid1 as occurring at the margins of narrow dykes of gabbro, norite, peridodite and pyroxenite, which are intrusive into the Dundas series of slates, quartzites and breccias. They occur chiefly in the neighbourhood of the Five Mile, near Zeehan, as small, narrow ore-bodies which are mostly less than 100 ft. in length.The ores are massive sulphides containing pyrrhotite, chalcopyrite, pyrite and the nickel sulphide, pentlabdite.A less common nickel-bearing mineral, gersdorffite, has been recently found in an adit, which is marked on Reid's geological plan of Dundas as the Hecla mine, 30 chains south of the crossing of the North-east Dundas tramway, over the Great Northern Creek, and at an, elevation of about 350 ft. above the tramway. The occurrence is in a lode traversing the Dundas slates and quartzites, and is situated, according to Reid's plan, about 20 chains beyond the northern extremity of a narrow basic dyke which is continuous for a distance of two miles in a south-westerly direction.The mine eonsists of a prospecting adit following the course of a lode for about 275 ft. in a direction a little west of south. The low values of the lode are indicated by a bulk sample from a shallow winze about 100 ft. from the entrance which is reported by Reid to contain:

Jan 1, 1935

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

An investigation into the causes of variable sulphur content in blast furnace metal produced at No. 4 blast furnace at the Port Kembla works of Australian Iron and Steel Pty. Ltd. was carried out. Theprogramme included an extended and detailed experimental study of a great number of the operating variables of the furnace, on a cast-bycast or four-hourly basis, over fourteen days.Possible causes of the variation were found in irregular operation due to sinter variability, and it was also clearly shown that slag conditions were most important in controlling sulphur contents of pigiron. Some decrease in sulphur variability was achieved, arising partly from this investigation, and it is hoped to try magnesia additions to modify slag conditions for better desulphurizing.INTRODUCTIONSulphur in pig iron is a problem common to many blast furnace operators throughout the world, but the direct causes and means of overcoming them are functions of the available raw materials, and are hence more particular to each plant and its operating practice. Sulphur in hot metal influences the steel-making operations, the rolling operations and the quality of the finished steel. The main problem associated with high sulphur in steel is "hot shortness", which leads to cracking of ingots and billets in rolling, to poor surface finish and to poor welding properties in the finished steel. On the other hand, sulphur is sometimes a desired additive to steel in order to promote free machining properties.Normal means of controlling sulphur A small degree of control of sulphur in steel is available to open hearth operators by alteration of slag volumes and basicity, but any large degree' of sulphur elimination is...

Jan 1, 1961

By B W. Riddol1s

The 1983 Energy Plan calls for an increase in North Island coal production from both underground and opencast sources from the 1982/1983 production of 843 000 tpa to approximately 3.4 Mtpa within the ten year period to March 1993. This increased production is scheduled to come from the following sources: Huntly West No 1 underground mine reaching full production of 1.26 Mtpa. Huntly East underground mine increasing production to 750 000 tpa. The proposed new Huntly West No 2 mine producing 100 000 tpa in its first year of operation û 1992. The proposed Ohinewai opencast producing 920 000 tpa for supply to the steelmaking plant at Glenbrook, replacing Weavers opencast which will be worked out in 1990. Rotowaro opencast producing at 220 000 tpa (currently being achieved). Two additional sources of supply which are not scheduled to begin production for at least ten years, and both of which have been designated for coal fired thermal power generation, are the Maramarua and Mokau coalfields. It was originally envisaged that development of both coalfields would be a combination of underground and opencast mines. The form of development is yet to be confirmed by detailed feasibility studies. The location of the Maramarua, Ohinewai (Waikare Coalfield) and Mokau deposits is shown on Figure 1. Worley Consultants Limited, in conjunction with their partners Rheinbraun Consulting GmbH (Germany) and Longworth McKenzie Pty Limited (Australia) have been involved with investigations and mining assessments for the Maramarua, Mokau and Ohinewai prospects. The Maramarua and Mokau studies form part of the New Zealand Coal Resources Survey programme of updating information to the Pre-Feasibility Mining Assessment level before proceeding to detailed feasibility studies. The Ohinewai study was commissioned directly by Mines Division to investigate the feasibility of mining coal by 1989 before reserves at Weavers opencast are depleted. This paper describes typical studies which are now being commissioned by Mines Division to investigate large-scale mining development and the effect geotechnical-conditions may have on coal recovery. The magnitude of these projects is reflected in the proposed outputs û up to2 Mtpa from individual mines û and the introduction of new continuous mining systems for both underground and opencast mines on a scale which has not previously been contemplated.

Jan 1, 1984

By H Park, V Sahajwalla

"Due to the increasing amount of gangues in iron ores, a beneficiation process is required more as a preliminary step for ironmaking process. However, mechanical grinding and washing of iron ore needs tremendous effort that increases operating cost. Therefore, there is a necessity of a novel approach to ironmaking which can tolerate considerable amounts of silica or alumina. In the present study, a high alumina-carbon composite pellet was examined for an ironmaking process. The effect of compositional changes in the CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets was investigated in a purpose built thermo-gravimetric analyser (TGA) at 1473K (1200¦C). As a result, alumina increased the reaction rate of carbon composite pellets by increasing surface area, while silica decreased the reaction rate by lowering surface area of samples. Infrared gas analysis assisted with the reaction kinetics of carbon composite pellets through measurement of CO and CO2 in off-gases. This study will assist with establishing the new pelletising method which differs from the conventional fluxed pellets.CITATION:Park, H and Sahajwalla, V, 2013. Effect of CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets, in Proceedings Iron Ore 2013, pp 467-472 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By P Rubie, B Morgan, J Russell, C Stewart

The relationship between efficient liner exchange, concentrator availability and concentrator profitability is well documented. Russell Mineral Equipment’s (RME) relationship with OZ Minerals’ Prominent Hill site personnel enabled sound collaboration between the two parties. Both parties worked together to identify the sources of productivity and efficiency loss and developed solutions to reverse them.This paper chronicles the identification of production inefficiencies and the resulting removal of mill relining from the critical path through the materialisation of mill relining optimisation strategies. Furthermore, this paper outlines other recent mill relining optimisation strategies developed by RME and tested at Prominent Hill, to demonstrate and achieve further productivity, efficiency and safety improvements.CITATION:Rubie, P, Russell, J, Morgan, B and Stewart, C, 2017. Mill relining optimisation – a story of collaboration, in Proceedings MetPlant 2017, pp 335–345 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

THE successful establishment of iron blast-furnace plants at Newcastle and Lithgow naturally invites attention to the economic utilization of the various products and by-products arising out of the industry.The general similarity in composition between Portland cement and iron blast-furnace slag very early attracted attention both in, the cement and iron-smelting industries. Probably the first use made of blast-furnace slag in the cementindustry was not of an honourable nature-viz, to use an almost worthless and cumbersome by-product as a not readily detectable adulterant in Portland cement, which was at that time very costly to manufacture.The astonishing discovery was made that in many cases the adulterated cement was stronger than the original unadulterated article. It was found that chilled blast-furnace slag introduced in moderate quantity and finely ground with the cement clinkerdid not injure, but usually improved, the quality of the resulting cement. This mode of, manufacture is recognized, especially in Germany, as a legitimate branch of the cement making industry.The use of slag for the manufacture of both slag cement and Portland cement has assumed very large proportions heth in USA and Europe so much so that in the former country plants not well situated and equipped for cheaply making cement from clay and limestone are being forced to close down. Slags from other than iron blast-furnaces, together with some of the latter, are not suitable for cement-making. All slags which disintegrate and fall into powder are wholly unfitted for cementmaking.Those highly charged with mineral oxide compounds...

Jan 1, 1918

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

By Ely K. W

On January 21, 1986, a methane ignition and subsequent mine fire occurred in the under- ground workings of the Jim Walter Resources, Incorporated No. 3 Mine located near Adger, Alabama. The fire, which began on a longwall face and eventually spread into the adjacent gob area, could not be extinguished directly and raged out of control for several hours. Sealing operations were begun underground by Mine Rescue Teams and the fire area was successfully sealed with the mine able to resume production in about one month. The No. 3 Mine liberated over sixteen million cubic feet of methane in twenty-four hours. The operation was unique, in that, the successful underground sealing of a fire in an ultra-gassy mine had not been attempted or com- pleted for several years. Maps and charts are included to give explanation of the typical data used to manage the recovery effort.

Jan 1, 1988

By Sneddon N

In November, 1975, Aberdare North colliery was sealed at the surface to extinguish an open fire underground.The fire had developed from a spontaneous heating in one of the open goaf areas of the mine.The mine was re-entered with normal ventilation methods following the isolation of the working district containing the fire. The isolation was accomplished by remotely sealing the open roadways with lly ash emplaced through boreholes from the surface. A subsequent re-entry operation similarly closed the roadways close to the fire and enabled the re-opening of the sealed district.Most of the mine and the underground equipment was recovered after clearing of numerous falls and production recommenced on 25th October, 1976.

Jan 1, 1978

Experiment of Improving the Quality and Decreasing the Impurity of Titanium Concentrate in Panzhihua Mine in China

Sep 13, 2010

By Gale D. C, Giles D. E, James Parker A

A zinc-lead-iron sulphide concentrate from McArthur River can be leached at atmospheric pressure in aqueous solutions with HCI, FeCl3, CuCI2, HCl/02 HC1/02/ CuCI2, Cl2, and CI2/CuCI2 to extract >98 per cent zinc, >90 per cent silver, and <15 per cent iron in 1-7 h at 95°. Galena is more reactive than sphalerite and is converted to lead chloride. Except for leaching with HCI, elemental sulphur is the the main by-product of the leach with little or no sulphate ion detected. The rates and products of these reactions are compared. It is recommended that aqueous slurries of the concentrate (50 per cent w/v) are leached at atmospheric pressure with Cl2 in the presence of copper(II) chloride, which accelerates the extraction of zinc. Hydrochloric acid is a by-product which is consumed bYJeaction with fresh concentrate in air at 60°. Copper is subsequently stripped from the leach solution and recycled by reaction with fresh concentrate at 100°. The separation, recovery, and electrolysis of zinc and lead chloride is outlined since this process would produce Cl2 gas which can be recycled and used directly in the leaching stage.

Jan 1, 1976

Magnetite cenospheres 40-270 I/m in diameter have been found during the combustion of pyrite concentrate.Micrographs of the surface and internal structures are presented together with comment on the mechanism of forrnation.The similarity to cenospheres found during the combustion of pulverized fuel was noted and speculation raised to their contribution to the dust and fume load in flash smelters.

Jan 1, 1980

Australia is the world's leading producer and exporter of mineral sands. Despite increased production from some other countries in recent years, Australia maintained its No.1 position in 1988 among world producers of mineral sands concentrates. Production of the titanium minerals -- ruffle, ilmenite and leucoxene, as well as synthetic ruffle -- by the seven companies currently comprising the Australian industry increased in 1988 in response to continuing strong demand for feedstock by the pigment industry. Production of co-product zircon remained at the 1987 level, reflecting declining zircon grades. Exports of mineral sands concentrates increased in 1988; export earnings exceeded $300million. Prices for mineral sands concentrates are now at a historical high and, assuming that the world economy remains strong, real prices should continue to trend upwards in the short term. Exploration in the Eneabba-Cooljarloo region and the Scott River area, both in WA, the Murray Basin, Vic, and the central Queensland coast area, has identified substantial resources of heavy mineral sands. These discoveries have reversed the trend of the early 1980s of falling resources of mineral sands. In 1988, BMR estimated that economic demonstrated resources (EDR) of ilmenite, rutile, zircon and monazite combined was about 72.8 million tonnes. However, a substantial portion of the resources on the east coast are frozen as a result of environmental considerations. The proportion of mineral sands concentrates processed in Australia increased with the commissioning of two new synthetic rutile plants; Australia is now the world's leading producer of synthetic rutile (total capacity 272000 tonnes), most of it for export. Australia's two TiO2 pigment producers have both increased capacity, lifting national capacity by some 70p ercent to over 120000 tonnes/yr. As part of the expansion one producer converted from the sulphate to the chloride process. Other new pigment plants are being proposed for the future.

Jan 1, 1989

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001