Search Documents

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By Herbert H. Mellus

TODAY the tractor-drawn carryall scraper has a very important role in the Open Pit div. of Inspiration Consolidated Copper Co. Carryalls have already moved over 3 million tons of material at costs comparable to or lower than for conventional truck and shovel operation, and a major program of scraper stripping and ore production schedules has developed from early isolated scraper applications.

Jan 10, 1953

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

By Paul A. Beck, M. N. Parthasarathi

By determining the (220) pole figure for OFHC copper rolled to 96 pct R. .A., the occurrence of four texture components of the type (135) [211] was confirmed. It was found that the total volume fraction of material close to the four symmetrical orientations of this type is larger than the volume fraction of the other components put together. THE rolling texture of copper was described by early investigators1'" as a mixture of components of the (110)[l12] and (112) [11l] types. Other studies, still using the qualitative photographic method of texture determination arrived, instead, at orientations of the type (135) [533] or (135) [211] for copper3'4 and at the closely related "Z-texture" for a fee nickel-iron alloy.5 The prevalence of this type of orientation, near (123) [412], in the rolling texture of aluminum and of copper was later confirmed by means of quantitative diffractometer methods.' However, in a recent paper7 Jones and Fell stated that the (110) [112] and (112) [111] double texture was in better agreement with the measurements of Young's modulus for cold-rolled copper.' These authors also expressed their belief that the "roll texture" can be determined by means of two photographic quasi-fiber texture patterns taken with sheet specimens rotated around the rolling direction and the transverse direction, respectively. Jones and Fell found7 that the results obtained from such patterns for cold-rolled nickel did not agree with any of the orientations mentioned above, but they suggested that the observed diffraction spots may have been brought about by the overlapping of reflections due to the (110) [112] and (112) [11l] double texture components. Jones and Fell concluded that the (123) 14121 type orientation is inconsistent with their patterns. They also stated, without offering any supporting evidence, that this orientation is inconsistent with the (220) pole figure. "Ideal orientations" are often used for a very rough description of the principal orientations encountered in a texture, It is, however, well to remember the fact that, no matter how "accurate", these ideal orientations are only schematic representatives of a continuous distribution9, which often (as in the case of rolled copper) includes extensive orientation spreads. The attempt by Jones and Fell7 to use elastic modulus data in deciding between various ideal orientations in the rolling texture of copper neglects this fact. The inadequacy of two-dimensional "axis density figures" in describing orientation distributions in sheet textures was previously discussed.9 It was also pointed out9 that there is no reliable evidence to prove that orientation distributions derived by the "quasi-fiber method" from rotated sheet specimens are fully equivalent to the corresponding information obtainable from quantitative pole figures. The view that a sheet texture could be adequately determined by means of two photographic quasi-fiber texture patterns is obviously erroneous9. The question as to the consistency with the (220) pole figure of ideal orientations derived from the (111) and (200) pole figures is, on the other hand, certainly very relevant. Since no quantitative (220) pole figure for cold-rolled copper appears to be available in the literature, the following work was undertaken. EXPERIMENTAL METHOD An extruded rod of OFHC copper, 1 in. in diam, was given alternate rolling (30 to 35 pct R.A.) and

Jan 1, 1962

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,' Barrett,' Dunn,3 and Richards' give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum' or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,'" aluminum,' or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.' Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", '" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

By D. R. Parrish, W. E. Lamoreaux, W. W. Owens

Several methods are now being used by the industry for determining the gas-oil flow characteristics of reservoir rock samples. Most of the laboratory experirnerltal rlzethods can be classified either as steady-state, unsteady-state, or Hassler-type tests. Although the validity of the results obtained by any specific method is not questiorzed, in general, the complexity of these methods leaves much to be desired. This investigation dealt primarily with the development of a simplified unsteady-state (gas drive) laboratory test method for measuring kg/ko re1ationships of small core samples. A procedure for selecting uniform and representative sandstone rock samples was developetl since it was observed that the reliability of the test resu1ts was dependent upon having a sample which was uniform in porosity and permeability. The importance of factors known to influence the results of this type test, such as oil viscosity, gas expansion, and pressure differential were eva/uated. The method of calculating the test results was found to give valid data over a wide range of gas expansion. The limits of pressure differential and oil viscosity which would insure reliable results were defined. In cornparisorz with other presently used testing methods, the gar drive method requires considerably less apparatus, is less time consuming, and is more readily adaptable to a routine type core test. INTRODUCTION The detcrmination of the gas-oil flow characteristics of reservoir rocks has been given concentrated study by the oil industry for the past decade. Both analytical and experimental methods have been considered. The analytical methods have generally relied on a simplified characterization of porous materials in order that the fundamental laws of fluid flow and capillarity could be utilized. More direct experimental methods have been proposed by numerous production research laboratories with the primary goal being a simple and inexpensive, yet reliable method for measuring the gas-oil flow characteristics of reservoir rock samples. The experimental methods which have been reported in the literature generally can be grouped into one of the following classifications: 1. Steady state1,2,3,4 in which a fixed ratio of flowing fluids is forced through the test sample until equilibrium conditions of saturation and pressure gradient are established. 2. Hassler or stationary liquid method5,6,7 in which a uniform liquid saturation is attained, usually through capillary desaturation, then gas or oil is flowed through the sample at a pressure drop insufficient to disturb the pre-established saturation. :. Non-steady state method1,8,9,10 In which only the gas phase is injected into the sample, causing displacement of the oil phase and resulting in a system of continually changing average saturation and saturation gradient. The steady-state and Hassler methods have been most popular because, no doubt, of the simplicity of the actual relative permeability calculations. The problems involved in these methods were limited to apparatus design and measurement techniques. In the steady-state method, for instance, a constant flowing fluid ratio is established which, at equilibrium, results in an essentially uniform saturation over the entire length of the test sample. Therefore, the basic flow characteristics could be obtained by correlating the average saturation of the test sample with the kg/ko determined at various flowing gas-oil ratios.

Jan 1, 1957

By E. L. Dougherty, J. W. Sheldon

Using the numerical techniques shown in this paper it is possible to compute the simultaneous dynamical behavior of multiple fluid-fluid interfaces in two dimensions. Hence, fluid-fluid inter face models of several oil recovery processes can be constructed which allow prediction of the effect of fluid flow in two dimensions on the behavior of these processes while taking into account various physical effects, such as saturation gradients, phase changes and thermal stimulation. Techniques for constructing fluid-fluid interface approximations for several oil recovery processes are reuiewed. The validity of these techniques is established by comparison to experimental results. The availability of a computer program for computing the behavior of multiple fluid-fluid interface problems makes the use of potentiometric models uneconomic. The results indicate the areal sweep efficiencies obtained from potentiometric model studies at high mobility ratios may be somewhat optimistic. The results also indicate that the areal sweep efficiency curves obtained at high viscosity ratios 2—4 using miscible fluids in porous media are misleading and that considerable care must be taken in defining the mobility ratio for a displacement process, especially for miscible fluids. INTRODUCTION Many of the methods used to estimate areal sweep efficiency assume that the oil recovery process can be represented by one or more fluid-fluid interfaces. When the mobilities of the displaced and displacing phases are assumed equal, this quantity can be computed using analytical mathematical methods.l.2 For non-unit mobility ratio, experimental methods based upon the fluid-fluid interface concept include potentiometric and electrolytic blotter models. Scaled models of porous media have also been used to study this problem. Fay and Prats3 and Aronofsky4 used numerical techniques to compute breakthrough sweep efficiency, but neither of these studies were extended beyond breakthrough. Numerical techniques which have been developed for solving a general fluid-fluid interface problem are presented in a companion paper.5 These techniques have been incorporated into a program for a large-scale digital computer which can treat simultaneously the dynamical behavior of as many as six fluid-fluid interfaces. Thus it is possible to simulate the behavior of several oil recovery processes taking into account such effects as saturation gradients. Techniques for representing several oil recovery processes by fluid-fluid interfaces are presented. Processes considered are conventional water flooding with and without a mobile gas phase, hot water flooding, miscible flooding and enriched gas drive. Other processes, whose effects could be studied by this technique, but are not considered in detail here, are underground combustion and steam injection processes and various slug processes such as gas-water injection and alcohol-solvent processes. Theoretical results obtained with single interfaces for mobility ratios of 0.25, 1, 2, 4, 8, 16, 32 and 64 in a repeated five-spot are compared to experimental results for this geometrical configuration obtained using miscible fluids and conductive analogs. Predicted recovery curves for water flooding in a repeated five-spot are compared to experimental results reported in the literature. Example calculations are shown for a conventional water flood in the presence of a free gas phase and for a hot-water flood. MATHEMATICAL PRELIMINARIES We assume that the rock matrix is homogeneous with constant thickness, absolute permeability and porosity. The fluids are incompressible. We also neglect the effects of gravity.

Jan 1, 1965

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge's method8 for measuring two-phase relative permeability. Although Sarem's method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem's assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem's.

The Institute conducts jointly with the American Society of Civil Engineers, 'American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them if certain properties. United Engineering. Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Don and George D. Barron. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn.

Jan 1, 1929

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By Fred H. Poettmann, J. K. Welchon, A. F. Bertuzzi

A series of gas-lift tests was made which verified conclusions reached from previous studies and which showed that gas-lift performance could be calculated if reasonably accurate data on the producing characteristics of the well are available.' The test installation is described. Its essential features consisted of a rate-of-flow controller to regulate the input gas and an auxiliary string of small diameter tubing to conduct the input gas to the point of injection in the eductor tubing. In general, it was shown that for continuous gas-lift operation, injection should be as deep as possible consistent with available gas pressure and rate of production desired. Calculated curves are presented which completely characterize the gas-lift performance of the well tested. INTRODUCTION A correlation based on field data from a large number of flowing and gas-lift wells, covering a wide range of oper- ating conditions, was developed which permitted the logical design and prediction of the performance of continuous gaslift installations.' The procedure made it possible to calculate the depth, pressure, rate at which to inject gas, horsepower requirements, and the effect of production rate and tubing size on these quantities. As a result of these calculations certain significant facts were brought to light or re-emphasized. The presence of efficient ranges of operation and an optimum injection depth for a given rate of production were shown to exist as well as the fact that the lower the tubing pressure the less the horsepower requirements to lift the reservoir fluids. The fact that the gas lift performance can be predicted by calculation does not mean that any given installation will perform over the entire range predicted. Many of the conventional continuous gas-lift installations will not permit operation over the entire range predicted by calculation (particularly in the efficient range of operation) because of the performance characteristics of the installation. Consequently, field tests were initiated for the purpose of investigating and arriving at a simple continuous gas-lift installation which would operate under all conditions predicted by calculation. The first series of tests involved the use of mechanically operated valves. These valves were slip-joint type valves which are opened and closed by lowering or raising the tubing at the surface by means of a hydraulic jack. These valves were chosen because it was hoped that they could be opened or closed at will and did not depend on the gas pressure in the annulus or the pressure of the fluid in the tubing for their operation. Unfortunately, the valves did not operate satisfactorily and it was imossible to open or close each valve at will. Some limited data were obtained, however, which verified the predicted benefits resulting from the use of lower tubing pressures. In the next series of tests the valves were removed and the gas was injected from the annulus through a 14/64-in. orifice equipped with a reverse check valve. A packer was set below the valve to seal off the space between the 2-in. tubing and 5-in. casing. The injection point was located at 3,810 ft. This arrangement provided satisfactory mechanical operation. However, it was impossible to obtain low rates of liquid production at low tubing pressures as predicted by calculation. A minimum gas injection rate existed below which steady flow was impossible. Liquid pro-

Jan 1, 1953

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By C. A. Heiland

THE investigations described were made on a portion of Clear Creek basin near Golden, Colo. (A portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line II.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.1 Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments.

Jan 1, 1928

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing 'fresh' and 'grown in' sources. 'Fresh' dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When 'fresh' sources are eliminated by chemical polishing the crystals have to rely on 'grown in' sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh' sources operate. Grown in' sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,' a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962

By Paul D. Conatore

INTRODUCTION There are important reasons for a discussion of tungsten resources, reserves, and production in the Circum-Pacific area. First, the world's chief tungsten deposits, as well as most of the world's tungsten reserves and production, occur in this region. It is well known that the world's largest tungsten reserves are located in southeastern China and that for many years, the largest individual mine in the world was there. Although China still has the world's greatest tungsten production, the very high-grade scheelite mine of Canada Tungsten Mining Corporation in the Northwest Territories is the largest producer of tungsten today. There is certainly a great quantity of tungsten in Asia, but the strategic importance of this fact is now offset by the wide distribution of mines and production facilities throughout the world, especially in other parts of the Circum-Pacific area such as Australia, Canada, and the United States. In addition, much of the Circum-Pacific area is comprised of Mesozoic-Cenozoic orogenic belts. These global tectonic units are regarded as very favorable for additional tungsten deposits, particularly scheelite-bearing tactites, and consequently, prospecting and exploration will most likely be concentrated in the Circum-Pacific area. Second, tungsten must be regarded as one of the, most important metals of modern industry because of its very special properties. It has the highest melting point, the highest tensile strength at elevated temperatures, and the smallest compressibility of any metal. The metal also possesses a very high density, excellent corrosion resistance, good thermal and electrical conductivity, and a low coefficient of expansion. As a result, tungsten has found increasing importance in a wide range of industries. From the filament in an electric lamp, to cutting tools and drilling bits, to the exotic radiation shields that protect supersonic aircraft and spacecraft, tungsten plays an indispensable role in our daily lives. The primary objective of this paper is to present an overview of important facets of known and suspected tungsten in the Circum-Pacific area. Resources, reserves, current production, planned capacity expansions, and new operations, as well as an assessment of the probability for development of deposits in the Circum-Pacific area, are discussed. RESOURCES The average crustal abundance of tungsten has been estimated at 0.0015 kilograms per tonne. A comparison of the abundance of various metals in crustal rocks to that of tungsten is presented in Table 1, which shows that tungsten abundance is similar to that of its commonly associated metals, tin and molybdenum. Table 1. AVERAGE CRUSTAL ABUNDANCE OF VARIOUS METALS (Grams per Tonne) [ ] With careful thought, it can be realized that tungsten ore deposits result from the concentration of the metal, through normal geologic processes, to levels substantially greater than its average crustal abundance. The minimum technologically and economically workable tungsten concentration, or cutoff grade, is a function of (1) deposit tonnage, (2) mining and milling methods, (3) production tonnage, (4) capital and operating costs, (5) tungsten market conditions, and (6) value of associated recoverable metals. The tungsten cutoff grade that is currently exploitable at a profit varies from 0.09% W03 to 1.55% W03, reflecting concentration factors from 470 to 8200, as shown in Table 2. Table 2. CURRENT TUNGSTEN CUTOFF GRADES [ ]

Jan 1, 1982

By A. M. Skov, L. F. Elkins

Inclusion of anisotropic permeability in mathematical analysis of pressure transients observed during development of the huge Spraberry field indicates a major fracture trend which is in good agreement with that observed by fluid-injection tests spread over a 12- by 17-mile area. Delineation of this trend is important in selecting a pattern of injection for the pending large-scale water flooding in this field. Determination of reservoir parameters yielding best agreement between calculated pressures and observed reservoir pressures in newly completed wells was made using an IBM 650 computer. INTRODUCTION The Spraberry field covering 400,000 acres is a tight sand of less than 1-md permeability cut by an extensive system of vertical fractures. Primary recovery dominated by capillary retention of oil in the fractured sand matrix blocks is less than 10 per cent of oil in place. Strong forces of capillary imbibition of water into the sand, coupled with water flow under dynamic pressure gradient, indicate considerable increase in oil recovery can be achieved through water flooding. Best results will occur if the pattern of water injection is selected to force the water flow across the grain of the major fracture system. Existence of an oriented vertical fracture system in the Spraberry, observed first in cores, was highlighted more recently by the 144-fold contrast in permeability along and at right angles to the major fracture trend required to match relative water breakthrough times in Humble Oil & Refining Co.'s waterflood test there. Spraberry operators since have conducted two gas-injection tracer tests for further areal confirmation of the fracture trend. Re-analysis of early reservoir pressure transients for evidence of anisotropic permeability has permitted many more local determinations of major fracture trend without resort to further field tests. This paper is limited to updating analysis of reservoir pressure transients to include anisotropic permeability as a test for orientation of the major fracture trend in the Spraberry. The reader is referred to Refs. 1 and 2 for information about general Spraberry reservoir performance and to Refs. 3 and 4 for information about significance of fracture orientation in selection of the injection-well pattern for water flooding the Spraberry. RESERVOIR PRESSURE DATA—DRIVER AREA During early development of the Spraberry Driver area, Sohio Petroleum Co. made the extra effort to measure the initial pressure in each of the 71 wells in a 5-mile-long area immediately after completion. Progressively greater reductions in pressure ranging up to 400 psi were observed throughout the six-month development period. Detailed data are presented in Ref. 1. Since the reservoir oil was undersaturated some 300 psi initially, early reservoir performance involving 55 new well pressures is subject to analysis as flow of a single compressible fluid in a porous media. Assumption of uniform permeability in all directions yielded good agreement between calculated pressures and observed pressures of these wells in the earlier study,' but subsequent, additional, mathematical development to include anisotropic permeability in the transient pressure considerations and present availability of electronic computers to perform the much more extensive arithmetical calculations now yield even better agreement. The previous analysis, assuming uniform permeability, consisted essentially of calculating pressure reduction expanding circularly around each producing well and summing these effects at the time and location of each newly completed well for comparison with the measured pressure reduction. Permeability, effective fluid and rock compressibility, and permeability X thickness were varied until the best match with measured pressures was obtained. The present analysis, assuming anisotropic

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968