Search Documents

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

The great Bingham Canyon mine and mill complex of Magna, Arthur, and Bonneville had their beginning in a 300 ton per day operation which was commenced by Daniel C. Jackling and his associates in 1904 as the Utah Copper Company. This small plant was quickly expanded to 500 tons per day and eventually Kennecott, the Utah Copper successor, was processing about 45,000 tons per day of ore in each of its mills, Magna and Arthur. Finally, in 1966, the Bonneville crushing and grinding plant was added to produce a slurry of ground ore for flotation concentration at the expanded Magna and Arthur mills. Bonneville is one of the few railroad dump primary gyratory crushing plants constructed in recent years; another which is described in this Monograph is Cuajone in Peru, started in 1976. Two others are the Climax Henderson unit and the Phelps Dodge Tyrone crusher, which has been fed by trucks since it commenced operation. The Bonneville, Henderson, and Cuajone crushers are all located considerable distances from their mines, hence the use of rail haulage. Shovels in the Bingham pit are 8 to 15 yd capacity; and ore is sent to the Bonneville crusher in 100 ton rail cars, where they are dumped, two at a time, by a hydraulically driven rotary dumper. Ahead of the 54 in. by 74 in. Allis-Chalmers gyratory are two grizzlies, each 27 ft 9 in. (8.46 m) long with bar spacings of 4 ½ in. (114 mm) at the feed end and 6 in. (152 mm) at the discharge end. Grizzlies are sloped at 38. Oversize rocks are re- moved from the crusher pocket by an overhead crane, and the crusher produces a nominal 6 in. (152 mm) product. Rail cars are dumped in the direction away from the crusher, and water sprays at the dumper level and in the rock boxes are used for dust suppression. There are two 72 in. by 19 ft (1.83 m by 5. 8 m) apron feeders under the 500 st cr'ushed ore pocket and two more under the grizzly undersize pocket. Feeder speeds are variable up to 72 fpm. Grizzly undersize is dropped to the feeder pocket by three shelves forming a rock ladder attached to the pocket walls. Each pair of apron feeders, one for crushed ore and one for grizzly undersize, discharge to a 72 in. (1. 83 m) picking belt for tramp removal; this belt feeds one of two 54 in. (1.37 m) feeder conveyors which in turn discharge to a 60 in. (1. 52 m) takeaway belt operating at 175-300 fpm (53.3 - 97.4 mpm). Both picking belts are equipped with metal detectors and tramp iron magnets, and a separate 30 in. (760 mm) conveyor is used to remove tramp material.

Jan 1, 1978

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows : the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize, The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4, The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute, 5. The recipient of the award shall be designated "The Hunt Medallist," This prize is administered by the Iron and Steel Committee. Awards of the medal have been made as follows 1920-Robert Woolston Hunt. 1926-Charles Lewis Kinney, Jr. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-

Jan 1, 1928

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By J. S. Aronofsky, R. Jenkins

A simple means of predicting the flowing well pressure history in a natural gas reservoir has been developed. The differential equation for unsteady radial flow of gases through porous media was solved by numerical methods using electronic punch card machines. The results obtained from these calculations are presented in a generalized form which is believed to be most convenient for engineering use. These results are compared with those presented in a paper by Bruce, et al4. An effective radius of drainage has been defined which permits the equation of steady state gas flow to be used easily to predict well pressures in gas reservoir depletion. An equivalent effective radius of drainage is defined for liquid flow systems and a comparison is made of the gas solution to the liquid solutions. INTRODUCTION This paper presents a numerical method for describing the transient flow of gases radially through a porous medium from which the production rate is specified. The results obtained from these calculations are presented in a generalized form which is believed to be the most convenient for engineering use. The principal application of these calculations should be to flow in natural gas reservoirs, in the interpretation of pressure drawdown tests, in the estimation of reserves, and in calculation of injection pressures required in gas injection and cycling operations. The evaluation of natural gas wells is based upon back-pressure tests in which measurements of production rate and flowing well pressure are made for periods of one, two, or more days. The flow is assumed to have stabilized at this time, and the observed values of pressure and production rate are used with standardized formulae to determine the well's allowable production rate. Furthermore, the results obtained from such a test of short time duration are extrapolated in such a manner to allow a prediction of what the well pressure will be at some future time for a specified (but possibly untested) flow rate. The manner of conducting such back-pressure tests suggests several questions as follows: 1. 'What is the definition of stabilized flow and what factors determine the length of time required for the flow to become stabilized? 2. How may the recorded values of pressure and rate be utilized? 3. As the well is produced and the reservoir pressure falls, how will the flowing well pressure change? Can this flowing well pressure be predicted from the back-pressure test? 4. Are the results obtainable from the test influenced by a particular procedure used in obtaining the results? 5. Is it possible to estimate the gross reservoir permeability from back-pressure data? It is not within the scope of this paper to provide solutions Or even to discuss adequately all the above questions. However. in considering such matters, the

Jan 1, 1955

By W. D. Robertson, D. A. Koss, A. J. Goldman

THE significance of the hcp (E) structure, which appears when Fe-Cr-Ni alloys (stainless steels) are transformed martensitically, has been the subject of considerable study and speculation.'-7 It has been proposed that the hcp structure is an intermediate phase in the transformation: fcc (austenite) — hcp (E) -bcc (0, martensite). However, recent studies by transmission electron microscopy6,7 have indicated that the hcp structure may be a consequence of the large shear strain (10 deg) associated with the fcc to bcc transformation. That is, the transformation to a bcc structure is accompanied by extensive dissociation of dislocations in the parent austenite, which has a low stacking-fault energy.'-'' X-ray diffraction analysis of the transformed alloy reveals a pattern of lines corresponding to an hcp structure, together with the parent austenite and the bcc product. The fact that the hcp structure is observed only in association with the bcc product in these alloys1'4'6'7 lends support to the conclusion that the hcp structure is a secondary product of the transformation. But, the evidence is circumstantial and more definite resolution of the two possibilities mains to be obtained. If the hcp structure is an intermediate product of the transformation, as in 1) above, then two distinct Ms temperatures should be observed, Ms and To evaluate this possibility, three different techniques that are particularly sensitive to the structural changes accompanying such transformations have been used in an attempt to detect two transformation temperatures in an Fe-15.1 Cr-11.7 Ni alloy: 1) high-sensitivity differential thermal analysis, 2) the temperature dependence of resonant frequency (elastic moduli), and 3) internal friction of cylindrical specimens vibrating in either longitudinal or torsional modes. To obtain the necessary sensitivity, a differential thermal analysis technique was developed for the purpose, Fig. 1. The differential temperature between a nickel standard and the specimen was amplified to produce a sensitivity of 0.02OC (0.7 v) in temperature difference. The specimen and the standard were surrounded by a copper block and the entire assembly was immersed in a solution of methyl and ethyl alcohol, freezing point, - 140OC, which provided the necessary thermal stability to reduce temperature fluctuations to negligible proportions. A cooling rate of about 1.5OC per min was obtained by bubbling liquid nitrogen through the liquid bath. In order to calibrate the experiment with respect to the evolution of heat in the transformation from fcc to hcp structures, differential cooling curves were obtained for an Fe-19.8 Mn alloy, which transforms martensitically to E.'"-' a Ms(e) temperature of 145°C was clearly defined by a temperature

Jan 1, 1964

By J. B. Cohen, M. B. Beaver, R. J. Black

RECENT investigations have shown that face-centered cubic metals may deform by twinning. Blewitt, et al' found that at 4.2"K the mode of def~rmation of single crystals of copper changed at large strains and markings formed on (111) planes. Later they- emonstrated by X-ray diffraction and metallography that the markings were twins and showed that favorably oriented single crystals of copper deformed by twinning at 78°K. They also observed twinning in silver and gold deformed at 4.2 and 78°K. Wagner3 obtained evidence for twinning from the peak shape of diffraction lines of silver cold-worked at 78°K, but twins small enough to cause such effects are not likely to be detected metal-lographically. In the work reported here lamellar structures were observed in deformed silver-gold alloys. They appeared to be mechanical twins, but metallography could not establish this conclusively. Their tendency to form depended on strain rate, temperature and composition. Specimens of silver-gold alloys (0 to 83 wt pct Au) were deformed plastically. One set was worked by hammering under liquid nitrogen, at room temperature and at intermediate temperatures. Another set was compressed slowly in liquid nitrogen to the same reductions as those produced by hammering. Tensile specimens (0.015 x 0.120 x 1.5 in.) of various compositions and approximately equal grain size (0.011 to 0.016 cm) were tested at -195°C and at room temperature. In microsections of all specimens deformed by hammering at —195°C thin lamellae appeared, Fig. 1. They were aligned in definite directions in each grain. In some grains they had two orientations. Where lamellae intersected, a displacement was apparent. Near the center of the left margin of Fig. 1 shear has taken place beyond the fully developed intersecting lamella. Many lamellae resembled Neumann bands in alpha iron. They were parallel to one side of triangular etch pits in the matrix (as in Figs. 1 and 2). The individual lamellae were narrow and had little substructure. This suggested that they did not result from concentrated local slip. The shape of etch pits within the lamellae differed from that of pits in the matrix, as can be seen in Fig. 2; this indicated a difference in orientation. Specimens slowly deformed at —195°C contained regions in which the lamellae were clustered. In these specimens some lamellae were bent and presumably had formed before the termination of the deformation. Structures of greater width than the lamellae were also seen.4 More lamellar structures formed on impact than during slow compression to a given reduction. This was true of all compositions. The structures became less abundant with increasing temperature of deformation. None was observed after extension to fracture at room temperature, but they could be pro-

Jan 1, 1959

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By P. W. Bakarian

PREVIOUS determinations1,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc-also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {102}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. EXPERIMENTAL METHOD Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 32 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. 2. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in, and evenly etched in dilute hydrochloric acid to a diameter of 0.038 ± 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1941

By Colin G. Fink, Leslie G. Jenness

Tantalum and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTaz06), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore,becoming (Pe, Mn)O.(Ta, Cb)2Os. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and si1ica. l Methods of Extraction Several methods have been proposed for the extraction of tantalum and columbium from their ores, among them being: 1. Fusion with Potassium or Sodium Bisu1fate.—The finely ground ore is fused with potassium bisulfate, after which the mass is boiled with water and the fusion repeated several times. The residue finally resulting is digested with ammonium sulfide to remove traces of tin and tungsten, boiled with hydrochloric acid, filtered and washed. These oxides are then dissolved in hydrofluoric acid, the silica evolved as silicon tetra-fluoride and the hydrofluoric acid solution used for the potassium double fluoride separation of tantalum. 2. Fusion with Sodium Carbonate and Sodium Nitrate.2—This fusion renders the tantalum and columbium soluble, and they are extracted

Jan 1, 1931

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102 to 102 ohm-cm as compared with 10-6 ohmcm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties.

Jan 7, 1957

By F. F. Sharpless

ON Saturday evening, Sept. 9, a small party of Institute members, their wives and friends, left New York to attend the Fall Meeting of the Institute at San Francisco. In this party there were: President and Mrs. Arthur S. Dwight; Mr. and Mrs. George D. Barron; Mr. and Mrs. H. J. Stehli; N. S. Spencer and Miss Spencer; the Secretary and Mrs. F. F. Sharpless. They were joined at Chicago by E. F. Eurich, and by Mr. and Mrs. R. L. Baldwin and daughter. Our party was met at Chicago by Mr. and Mrs. L. V. Rice, Mr. and Mrs. A. D. Terrell and W. F. Boericke, who constituted themselves an impromptu entertainment committee and proceeded to carry out a delightful little program. We were taken to the Lake Shore drive, where a stiff wind off the lake refreshed us after a sultry day on the train, and on our return to the city saw Chicago illuminated with all its brilliance of electricity. We were entertained at dinner at the Drake Hotel. In spite of being two hours late getting into Omaha, we were right on the dot at Denver on Tuesday morn-ing. Horace F. Lunt came to the hotel soon after breakfast, and told us that a trip to the mountains had been planned. Having learned the number in the party, he began to gather up his automobiles for a 10 o'clock start.

Jan 10, 1922

By W. L. Phillips

The plastic properties of lithium fluoride and magnesium oxide under compression were investigated in the temperature range 25° to 1000°C. At the higher test temperatures, the critical resolved shear stress and the rate of work-hardening of both materials decreased. At the same time, the number of stress lines decreased and the individual stress lines became wider. The density of dislocations decreased for a given strain the higher the test temperature for lithium fluoride. The decrease in the critical resolved shear stress as a function of temperature could be fitted by the equation 7 = Toe-KT. THE influence of temperature on the stress-strain curves of a variety of metal single crystals has been studied for a wide range of temperature.1"5 In general, it has been found that both the critical resolved shear stress and the rate of work-hardening decrease rapidly with increasing temperature and fall to a value of essentially zero well before the melting point is reached. AS the test temperature is increased, the density of slip lines has been found to decrease, while the width of the individual lines increases. Recently, Gallagher,' Graf et al.,7 and Pate1 and Alexander8 have found that single crystals of germanium and silicon, which have a covalent bond, can be plastically deformed at elevated temperatures. In compressing germanium it has been found that the strain-hardening coefficient decreased very rapidly as the temperature was increased. The coefficient did not tend to zero, however, as the melting point was approached. The plastic properties of ionic crystals at elevated temperatures have not been extensively investigated. In the only work previously reported Tamman and salge9 and Theile10 have shown that the yield point of sodium chloride single crystals tested in tension and compression decreased slowly with increasing temperature, falling to zero at the melting point. As the temperature was increased, they found a substantial increase in the amount of plastic deformation that could be sustained before fracture; and at temperatures above 400°C in tension tests there was an obvious necking which produced local extensions of up to 3000 pct. The purpose of the present work is to extend the knowledge of high-temperature deformation to the ionic crystals, lithium fluoride and magnesium oxide. The following were investigated: 1) The gross shape of the stress-strain curve at several temperatures. 2) The change in the critical resolved shear stress as a function of temperature. 3) The appearance of slip bands and the density of dislocations as a function of strain and temperature. EXPERIMENTAL TECHNIQUES The lithium fluoride and magnesium oxide used in this investigation were purchased from the Harshaw

Jan 1, 1961

ASIDE from the John ,Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows : the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circum- stances, both prizes may be allotted to one person provided that he is not over 10 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main' contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered by the Iron and Steel Committee. Awards of the medal have been made as follows: 1920-Robert Woolston Hunt. 1926-Charles Lewis Kinney, Jr. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-

Jan 1, 1928

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

IN 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group -SO4- or _S03- are excellent collectors for cassiterite and promise to be selective.1 The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000gram Denver cell. EXPERIMENTAL METHODS Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously described.5-10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these tests determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver Submachines.--Melbourne tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By C. A. Stetefeldt

IK the dry-crushing of ores, either by stamps, rolls, or other machinery, it is essential that the material should be free from moisture. Hence a contrivance which effects this with economy, and is of durable and compact construction, is a great desideratum. It is claimed for the below-described shelf dry-kiln, that it possesses these qualifications in a high degree. The construction of the shelf dry-kiln is based on the Hasenclever principle. That is to say, a number of inclined shelves are arranged zig-zag above each other in a vertical shaft, having openings or slits where they meet, on which the ore rests in a stratum, the thickness of which is governed by the width of the slits and the inclination of the shelves. If a portion of the charge is removed at the end of the bottom shelf, a sliding motion of the ore takes place on all shelves above, and the top shelf is replenished from a hopper set over it. It will be seen that the shaft is divided by the shelves into a number of triangular prismatic spaces. Through these the hot gases from a fireplace are made to circulate, each space communicating with the next one by a flue arranged in the sidewall of the shaft. These flues being located on alternate sides of the shaft, a continuous passage is formed through the whole structure. After thus stating the principle of the construction, its details will be easily understood by reference to the drawings, Fig. 1 to Fig. 5. The drawings, Fig. 1 to Fig. 4, represent two kilns united into one structure. The cast iron shelves(a) are 2 feet 4 inches wide and 5 feet long, with sides and a back 4 inches high, and are cast a full halfinch thick. How they rest on the brackets(d), and interlock each other, is shown in Fig. 5. Three such shelves, with an inclination of 38') are placed in one row in a brick shaft 7 feet 1/2 inch wide and 4 feet deep. The ore hoppers(g) rest on the iron bems(f). At the end of the bottom shelves are the discharge-doors(b), with shoots projecting beyond the front wall. A swinging apron(e) keeps the ore in place. By dropping it a car below the shoot is filled with dry ore. A number of extra-large pieces of ore may cause a stoppage in the slits ; for such an emergency the openings(e) are provided, through

Jan 1, 1884

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy'-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957