Search Documents

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By Charles C. Russell, Glenn C. South

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Bruce F. Grant, Stefan F. Szasz

During 1947, a Sinclair research team was assigned to investigate thermal methods of oil recovery. The assignment was recommended by a survey of possible research approaches to increase the amount of oil that ultimately can be recovered from oil producing reservoirs. The use of heat to stimulate oil production rates by the melting of paraffin deposited in well bores can be traced back to within one or two decades of the drilling of the Drake well. The application of heat on a larger scale has been discussed by generations of oil producers. Shortly after the turn of the century, one intrepid operator is reported to have injected steam into a Pennsylvania property. After a few weeks, he apparently became discouraged and terminated his experiment. Subsequently, the literature contains references to several well-developed techniques for supplying heat to a producing well bore to melt paraffin or to reduce the viscosity of oil contained in the formation immediately around the well bore.1.?.3.4 Some early references discuss procedures to furnish heat to the reservoir,5,6 with the injection well as the heat source, thus obligating the process to maintain the entire rock mass at a temperature above that at which the desired improvement in oil recovery would occur. Another approach to reservoir heating was reported by a group of Russian technologists in 1935.7,8,9 They definitely demonstrated that combustion can occur within the porous structure of an oil-bearing sandstone. Their field experiments, however, relied less on combustion within the rock than on heat furnished by combustion of oil supplied to the injection well bore. Ignition of the air-oil mixtures in the well bore was found very difficult, and the field tests were carried on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well, on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well. The Brundred Oil Corp. reportedly obtained combustion in the sand immediately around the injection well bore, but the experiment was abandoned because of interference with normal production schedules. Injection capacity of the experimental well was greatly reduced by firing. The well was reshot and pieces of sand showing partial fusing of the quartz matrix were recovered. To the authors' knowledge no other field experiments utilizing combustion techniques for formation heating were undertaken prior to 1948, although the patent literature evidences continued interest in formation heating."'," CONCEPT OF COMBUSTION-SUPPORTED HEAT WAVE The references cited were in agreement that heat applied to a reservoir would increase recovery, but there

Jan 1, 1955

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)' into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen' observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C'4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman' utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By R. G. Fleck, W. R. Webb

The concentrate produced from the Adirondack magnetites is, of course, too fine for direct use in a blast furnace and must be agglomerated before it can be considered a blast furnace ore. The four operations in the area use sintering -three, including the Jones & Laughlin operation, employing the Dwight Lloyd continuous type machine and one operation using the Greenawalt batch type process. Each operation uses fine anthracite coal, either No. 4 or No. 5 buckwheat size, for the mix fuel.

Jan 6, 1950

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining's reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company's mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By S. S. Arentz

PLANNED health and safety programs have become an essential part of American industry because such programs lead to increased operating efficiency, improved labor relations, better public relations, and to substantial savings in compensation insurance. Those of you who have had the unpleasant duty of informing the wife or widow of one of your men of his serious injury or death while on the job, know that all the benefits of a successful safety program do not show on the balance S. S. ARENTZ, Member AIME, is General Superintendent, Nevada Operations, Combined Metals Reduction Co., Pioche, Nevada. AIME San Francisco Meeting, February 1949. TP 2741 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Jan. 6, 1949. sheet. These programs are of particular importance to the mining ,industry because mining's reputation as an unusually hazardous industry and the commonly isolated location of mining operations tend to focus attention on these problems. Description of Operations: Before proceeding with a discussion of our health and safety programs at Pioche, it may be proper to give a brief description of Pioche and of our operations there. Pioche is one of the early Nevada mining camps. It was founded shortly after the discovery of high grade silver ore in 1863 and mining has continued with more or less regularity to the present day. In an era of lawlessness, Pioche was notorious. The story persists that 75 men died with their boots on before one died a natural death, and old payroll records show that nearly as many gunmen were employed to stand off claim jumpers as there were miners working the mine. That was probably as close to a safety program as the times permitted. Pioche is situated in southeastern Nevada on the main highway between Ely and Las Vegas. The camp is on the flank of "Treasure Hill," near the original silver discovery, at an elevation of about 6000 ft. The present day population of about 2000 is primarily dependent upon the mines of the area, although Pioche also serves as the county seat of Lincoln Couqty and as the center of the surrounding livestock industry. The camp is served by a branch of the Union Pacific Railroad and receives power from the generators at Hoover Dam. The Pioche operations of the Combined Metals Reduction Co. were started in 1923 when the first complex lead-zinc ore was shipped to the company's mill at Bauer, Utah. The modern mill at Pioche was completed in 1941. The operations are medium sized in the nonferrous field, employing an average of 350 men in the mine, mill, and related works. The complex lead-zinc ore is mined from replacement deposits in a comparatively flat, extensively faulted, limestone horizon. Mining methods vary from stull-supported open stopes to filled square-set stopes. The thin bedded limestone and shale overlying the ore is allowed to cave as areas are mined out and caving frequently follows closely upon ore extraction. The relatively heavy ground and the numerous faults add to the problems of safe mining. The mine is well mechanized and the mill and surface plant are modern and well equipped. Labor is organized in a C.I.O. union and labor-management relations have been unusually harmonious. During most of the period since 1923 a competent supervisory staff worked to reduce safety hazards but the primary responsibility for safety rested on the individual workman. Accidents happened and all too frequently they were regarded by all concerned as unavoidable. In October 1939, the late Robert L. Dean became superintendent at Pioche. Most of his previous experience had been in the fields of iron and coal mining and from that experience he brought the concept that no accident is unavoidable. Many of the features of our present health and safety programs were initiated by Mr. Dean during his term as superintendent. Health Program: Our health program centers in Dr. Q. E. Fortier and his new, well-equipped, and well-staffed, modern hospital in Pioche. The program starts with a thorough pre-employment physical examination and is followed by yearly re-examinations at the expense of the company. The Pioche Mutual Benefit Association, to which all Pioche mine operators and employees belong, pays benefits covering hospitalization and surgery expense incurred by employee members and their families. The Association is governed by a board of directors elected by its members. The mine operators of the district donated the original capital and pay the monthly dues of the employee members. The employees pay the dues covering members of their families. Though not strictly a part of the

Jan 1, 1951

By Margaret Dienes, Karl L. Fetters

IT is recognized that ingot structure is important in determining the quality of finished steel. Such elements of ingot structure as the size, shape and distribution of primary crystals; the size, shape and distribution of shrinkage cavities; the degree and kind of segregation (both macro and micro); the distribution of nonmetallic impurities and gas cavities are each the result of solidification phenomena. These structural features vary with variations in ingot practice: Their control requires a knowledge of their correlation with the variables of ingot practice. The structures of full-sized commercial steel ingots have been studied extensively by the Steel Ingots Committee of the Iron and Steel Institute.1 This work has contributed much to our knowledge of ingot structure and the factors that control it. These investigations of necessity have been limited in scope because of their costliness and the great amount of time required. Studies of the structure of small steel ingots have not been very satisfactory because of the rapid rate of freezing of the ingots. Their structures are thus difficult to resolve and to interpret. Medium sizes of steel ingots in the ranges of 150 to 500 lb. do offer opportunity for study, but their cost also becomes greater and their use less expeditious. Experimental models for the study of steel-ingot structure have been made of nonferrous metals. Gathmann2 used lead-tin alloys and reported that they were satisfactory for determination of the location of the major shrinkage cavities and the "planes of weakness" resulting from the pattern of crystallization. Certain features of mold design have been illustrated by these results. Bezdenezhnihk3 has used copper and aluminum ingots similarly and has shown the effect of mold-wall thickness on the depth of columnar grains. These studies of nonferrous models have been useful, but their results have been limited because the analogy with steel ingots obviously is not a close one. Model wax ingots have also been useful in pointing out important features of mold design. Gathmann4 watched the solidification of wax ingots, through a glass-walled mold, and has reported the effects of mold type on the location of the shrinkage cavities. Segregation was simulated by using a mixture of paraffin and stearine and adding a red dye that on freezing segregated preferentially to the stearine. Brearley5 also used wax models to determine .the effects of some of the principal features of mold design. Carlsson and Hultgren6 used stearic acid to show that the columnar crystals of ingots tend to slope upward progressively from the mold wall toward the center of the ingot. As with the nonferrous ingots, the wax ingots have

Jan 1, 1943

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By K. E. Merklin, F. D. DeVaney

In the past most of the research in pelletizing has as its aim the production of a physically strong pellet. Now that this problem is solved, more attention is being paid to uniformity in grade and chemical composition. Consideration has been given in recent years to a study of additives which will make pellets partially or fully fluxed. Blast furnace tests show fluxed pellets to have advantages over both fluxed sinter and acid pellets. Lower slag volumes are used more frequently in the blast furnace and the uniformity of the charge, both physically and chemically, is becoming increasingly important. A considerable improvement can be secured by having all of the flux uniformly distributed through the pellets in a calcined state. A fluxed pellet, therefore, should be a superior product. The use of an ore burden that contains an appropriate quantity of fluxing materials is not new to the blast furnace industry. For years the Minette ores of France and Germany, the Clinton ores of the Birmingham, Ala., areas, as well as others, which are low in iron but contain calcium carbonate in sufficient quantities to give them self-fluxing properties, have proven economical. The adaption of the sintering process to the preparation of ore burdens provided a means for artifically associating the fluxstone with the iron ore prior to charging to the blast furnace. In 1944 Torpl discussed the effects of using lime in sinter made in Sweden on the sinter's metallurgical performance in a blast furnace. Hessle2 reported in 1945 on the advantages of using lime in sinter to increase the sintering plants' capacity and reduce fuel requirements. Robinson3 discussed the use of lime in Swedish sintering practice at the 1950 Blast Furnace, Coke Oven, and Raw Materials meeting. One of the suggested advantages was the combining of lime with silica to prevent the formation of a fayalite slag, which is difficult to reduce in the blast furnace. Nilson4 at the same meeting commented briefly on experimental work that had just started in the U. S. on the use of lime in sinter. The literature tends to indicate that most of this early work was directed towards improvement in sinter physical quality, and the fact that the feed to the blast furnace was partially fluxed was incidental. It was not long, however, before blast furnace advantages were being claimed. The matter was forcibly called to the attention of North American operators by reports of remarkable production records established by the Russians using fluxed sinter. The leading step was taken on this continent by the Steel Company of Canada in 1957; McMahon5 reported on the marked improvement in performance of an 18-ft blast furnace using fluxed sinter at its Hamilton works. Other North American operators quickly followed theStelco lead.

Jan 1, 1963

By J. H. Lightfoot, Stuart E. Buckley

DEEP drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.1 The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen4,5,6 and by others,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems.9-17 It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 lb. per sq. in. Thus, at pressures of 2500 lb. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 600°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduction. The combined effects of pressure and temperature on condensation and vaporization of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpretation of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate systems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21.22 it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has

Jan 1, 1941

By H. G. Doll

An earlier paper on the general subject of the SP log has analyzed the limitations of that log, in particular when dealing with thin permeable beds enclosed in thick highly resistive ones. Under such conditions, the SP log does not give a good definition of the permeable beds. Selective SP logging is a new method which gives an accurate determination of the permeable beds; even in highly resistive formations, except when the salinity of the mud is extremely high. It also permits a close approxi. mation of the static SP to be obtained. The method consists generally in controlling the potential of auxiliary electrodes located in the drill holes in the vicinity of the measuring electrode. In this manner. the flow of SP current along the drill hole is modified to counterbalance the effect of highly resistive strata. Several procedure; and arrangements used to record selective SP curves and static SP curves are explained. Field examples illustrating these methods are given and discussed. INTRODUCTION In an earlier paper,' the shape of the SP curves and the amplitude of the SP peaks were analyzed, considering how the circulation of the SP current is influenced by the subsurface media as a function of their geometrical configuration and their resistivities. It was shown, in particular. that the permeable beds situated between highly resistive formations are sometimes indistinctly indicated by the deflections of the SP log. It is the purpose of this paper to dircuss a new method now being developed, namely selective SP logging, whose principal feature is to enable a more accurate determination of the depths of the permeable beds present in highly resistive formations, such as occur in limestone fields. It will be shown also how an addi-tional curve called the static SP log can be derived from the selective SP log, or recorded directly, to facilitate the interpretation. Another purpose of the static SP log is to provide an approach toward the determination of the value of the static SP, where this value is not readily given by the SP log. This application. although less important at the present time than that mentioned above, nevertheless is of interest, inasmuch as, according to laboratory and field experiments conducted by several investigators, the determination of oil saturation of reservoirs from the data of the electric log implies the knowledge of the resistivity of the connate water,2,3 to which the static SP seems to be related.4,5,6,7 PRINCIPLE OF SELECTIVE SP LOGGING The method of selective SP logging of the formations traversed by a bore hole consists in recording two curves under the following conditions: The measuring device comprises one measuring electrode M and two additional electrodes G-G', connected to each other. located above and below

Jan 1, 1950

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By C. H. Mathewson, H. l. Burghoff

The study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and go per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrys-tallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300°, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrys-talline 70-30 brass. Previous Work Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler2 have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty and Moore." Results of the last-named investigation were published while the present work was in progress. Miller5 examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior of iron crystals under static tensile loading at room temperature was reported by Gensamer and Meh17 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of crcep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By H. l. Burghoff, C. H. Mathewson

The study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and go per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrys-tallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300°, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrys-talline 70-30 brass. Previous Work Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler2 have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty and Moore." Results of the last-named investigation were published while the present work was in progress. Miller5 examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior of iron crystals under static tensile loading at room temperature was reported by Gensamer and Meh17 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of crcep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By C. S. Roberts

Four binary alloys in this system were creep tested at 300°' to 600°F. A photographic study of microstructural changes showed that the outstanding creep resistance results primarily from a potent precipitation hardening locally at grain boundaries. Twinning was correlated with the primary stage and nonbasal slip with the tertiary stage of creep. THE utility of the rare earth metals as ingredients of magnesium alloys destined for elevated temperature application has been recognized for about 15 years. A review of the early development of these alloys has been given by Leontis. 1,2 It has been only recently that a desire has arisen to understand basically their remarkable creep resistance. The present research had that object. The work of Leontis showed that the differences between the behavior of the individual magnesium-rare earth element binaries was of commercial significance. However, the variations were small compared to the overall difference in creep resistance between the group as a whole and the magnesium alloys of the Al-Zn type. It was decided to conduct this investigation with one binary system which would be representative of the magnesium-rare earth element alloy group. Cerium was chosen as the solute because of its near-middle position in the series and because of its availability in the commercially pure form. A previously published description of the creep behavior of electrolytic magnesium" serves as the background to this research. The experimental approach used in that investigation has been partially repeated here. A series of binary alloys was planned to include the following: 1—A dilute alloy which would contain the cerium almost entirely in solid solution. This would assess the solid solution effect. 2—An alloy which is nearly saturated at the selected solution heat treatment temperature, 1070°F. Here the effect of nearly maximum precip- itation would be obtained without the influence of undissolved Mg-Ce intermetallic. 3—An alloy containing slightly more cerium than is soluble at 1070°F. This would allow the investigation of the effect of a small amount of excess intermetallic. 4—A high cerium alloy in which the influence of a large volume of undissolved intermetallic may be examined. Experimental Details In order to specify compositions of the binary alloy series a knowledge of the solubility of commercially pure cerium in solid electrolytic magnesium and also of the composition of the terminal intermetallic phase was necessary. The latter has been proven to be approximately Mg,Ce by Voge14 and Haughton and Schofield.5 A series of both cast and extruded alloys were solution heat treated 24 hr at 1070°F for a solubility determination. Lineal analyses of the polished and etched microstructures were accomplished with the aid of a Hurlbut

Jan 1, 1955

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.'-'0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3'5 intercept length,6"9 or diameter.1'2'4'10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965