Search Documents

ONE of the fundamental reasons for the extreme rapidity with which the Porphyries developed after the trail had been blazed at Bingham was the amenability of the deposits to prospecting and proving of the ore either by churn-drilling or by diamond-drilling. At Ray churn-drill data formed the principal basis for early calculations of ore reserves; and in 1913, Inspiration floated its first bond issue for $6,000,000 on the strength of the estimate of 45,000,000 tons of sulphide ore assaying just over 3 per cent copper. The money was obtained in spite of the fact that no one ever had actually laid eyes on more than a minute fraction of that ore. The customary method of developing a copper deposit before the Porphyry era had been to sink shafts or drive adits and then to follow and expose the veins or lodes with horizontal and vertical underground workings-drifts, crosscuts, raises, and winzes. The excavated material sometimes was sampled in bulk; but always the walls of the openings would be channeled at intervals to obtain small samples representative of the ore left in place. This process was known as "blocking out" ore. It was costly and it required a great deal of time to prove the existence of immense tonnages. The early development at Utah was done in this way; likewise, at Miami. This fact helps to explain why only 3,000,000 tons of ore was reported as being developed when J. Parke Channing wrote the report on which the original Miami financing was based in March, 1908. Fortunately, his 3,000,000 tons averaged 3'per cent copper. At Ray, Seeley W. Mudd estimated 3,000,000 tons of ore in June, 1908, developed principally by underground working; but by the end of 1909, Henry Krumb was able to report 50,000,000 tons as the fruit of a little more than a year of churn-drilling.

Jan 1, 1933

By Henry P. Ehrlinger

The Alta and St. Louis mines of the Alta Mines, Inc., produce a somewhat oxidized ore with a talc gangue that presents quite a problem in milling. For several years the mill recoveries were relatively low and there seemed to be no cure for this condition even with increasing the various collecting agents and frothers to two or three times of what they should be. The usual alibi of "oxidized ore" was given as the reason for these results and the matter stood there for some time until these investigations were started. Flowsheet As a brief outline of the flowsheet the ore is crushed to minus I in. in a Telsmith jaw crusher and then fed to a 64½ Marcy grate mill. The resulting product from the grate mill is passed over a trommel where the coarse particles (plus 7 mesh) are returned to the grinding circuit through the classifier. The under 7-mesh pulp is passed over two Denver mineral jigs where a high grade concentrate is produced, thence over two Wilfley tables where a table concentrate is produced and about 80 pct of the oxide lead recovered. The tailings from these tables are pumped back to the classifier and after classification the 30 pct pulp density product, which overflows the lip, is passed into a series of 10 Denver economy flotation cells where a lead-copper concentrate is produced. Three products are made and shipped to the smelter termed jig, table and float concentrates. Results with various Reagents In March of this year work was started on the metallurgical problems of the mill and, as is shown in Table I, the results obtained were not too efficient. Tests were run with various reagent combinations that were recommended for ores of this nature but there was no appreciable effect on the recoveries. The grades of the flotation concentrates were reduced by the insoluble picked up and retained by these more powerful collectors and frothers. Results with "Metso" In past work on ores of this type the use of "Metso" had improved gold and lead recoveries, but no effect on the silver and copper recoveries had been noted. To

Jan 1, 1949

By C. S. Barrett

W. Hofmann, J. Ziegler, and H. Hanemann—Having dealt with the same alloys in the winter 1941 to 1942, we want to give a short report on the generating of the hexagonal kappa phase by deforming the supersaturated alpha phase, which we then observed. This work was delivered as a Doctor of Engineering dissertation to the Technical University of Berlin by J. Ziegler in 1942. It still exists in two copies, somewhat damaged, a brief publication of it having been issued in Fiat-Review. Our work was started from the alloy Tombasil with 4.5 to 5 pct Si, 14.5 to 14 pct Zn, the rest Cu. Torpedo propellers were die cast from this alloy in Germany during the war. In order to improve this alloy, annealing was tried. By this treatment the alloy became at the same time harder and more brittle. A further research of this process was made in the Got-tingen University30 and the "Institut fÜr Metallkunde" of the Technical University of Berlin. It soon was apparent that the Cu-Si diagram at our disposal15,31,32 would not fit the observations. For this reason the pith of the matter became from then on the Cu-Si system. At that time we did not know of Smith's* and Andersen'sm latest diagrams. We first knew of them from Dr. Barrett's publication. Twenty-two alloys containing 2 to 11 pct Si were melted in a nitrogen atmosphere and generally homogenized for 2 to 4 hr at 800 °C. Part of the samples were then annealed at 700°, 600° and 500°. Annealing was followed by quenching in water. The phases corresponding to the various temperatures were identified by X-ray and microscopy. The Debye-Scherrer photographs generally were made of filings. The latter were produced after the last anneal of the samples, then equally annealed another 30 min in evacuated glass tubes and quenched in water. In the region of concentrations examined, the Cu-Si phases already known to us were observed: alpha, kappa (then called beta by us), gamma. By hot exposing an alloy of 7.69 pct Si at 800" and 750°,

Jan 1, 1951

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

The members of the Institute have probably seen in the daily papers notices of the plans of the Secretary of the Navy to. form an Advisory Board to assist the Government to make available the latest inventive genius of the country. Secretary Daniels has appointed Mr. Thomas A. Edison Chairman of this Advisory Board and has officially invited the Institute to secure the selection of two of its members to serve. on this Board. The Secretary in his letter states: "I feel that the work your Institute has done has been such as to give it the right to be in a way officially represented, and the Navy Department desires in this way to testify to its own appreciation of the splendid work for our country that your Institute has done. I have the emphatic approval of Mr. Edison, and he agrees entirely with me that your Institute should he represented in this way and that no better method of getting the kind of men we need could be devised." The invitation of the Secretary of the Navy has been officially accepted and steps have been taken to nominate the two members. Since the Constitution provides for no meeting of the Board of Directors until September, and as Secretary Daniels urged early action, the matter was discussed at a special meeting of the Executive Committee of the Institute, at which were present as many members of the Board of Directors as were in New York City at the time. Invitations were also extended to other members of the Institute who happened to be in the vicinity. At this meeting it was decided to submit the matter by a special letter-ballot to the Board of Directors and in doing so to suggest or nominate five members of the Institute, accompanying this nomination with the statement that the Directors might vote for two of the members so nominated or for any other members of the Institute not so nominated. It was voted at this meeting that it. was the sense of those present that in view of the fact that this committee was an advisory one the type of men to be chosen should be men of administrative or executive ability, cap-

Jan 9, 1915

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark' makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter' presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940

By Frank A. Herald

Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations may be involved, our figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Wile we have not provided a column for showing the thickness of the productive zone, generally the difference between average depth to bottoms of productive wells

Jan 1, 1935

A. 11. P. WYNNE, San Jose de Gracia, Sinaloa, Mex. (communication to the Secretary): In the comparative tests reported by Mr. Tays, the stamp-batteries were provided with various styles and mesh-sizes of screens, while the Bryan mill was run throughout with a slot-punched Russia iron, equivalent to a 30mesh wire screen. This is a somewhat onc-sided method of comparison. Should not the Bryan mill also have had the chance to show what it could do with other screens? I cannot wholly approve Mr. Tays's proposed improvements upon the Bryan mill. In my judgment, the inventor has given us a machine well-adapted to the work for which it was designed, namely, the crushing and amalgamation of soft ores. In my judgment, the principal cause of failure to amalgamate satisfactorily in the Bryan mill is not, as Mr. Tays thinks, the shallowness of the basin, or the lack of copper plate about the inside periphery of the mill, but rather the want of experience and practical knowledge on the part of most amalgamators. Having had experience, not with one Bryan mill only, but with several, and taking into consideration the experience of other capable mill-men, I am positive that the proper way to save gold ill this mill is: first, to use enough quicksilver to keep the amalgam liquid, thus allowing it to accumulate in the annular space between the dies and the rims of the basin; secondly, to replace the old dies, when a little more than half worn-out, with new ones; and, thirdly, to clean up the mill at least every two weeks—or oftener, if rich ore is being treated. It is evident that Mr. Tap endeavored to amalgamate quite " hard," as is done in a stamp-battery, in which case the swash of the pulp would scour off portions of the hard amalgam adhering to the inside plates and dash it through the screens— after which a considerable amount would be lost through floating on, or in, the pulp in its journey over the outside plates, and

Jan 1, 1900

By P. R. Sperry

Aluminum alloy 3S was examined to determine the relationship between the applicable phase diagram and the microstructures produced under conditions tending toward non-equilibrium as well as equilibrium. The only phases present in the alloy were aluminum, (Mn,Fe)A16, aAI(Mn,Fe)Si, and silicon. It was found that the alloy behaved essentially as though it belonged to the Al-Mn-Si system. The effects of various solidification rates and of various homogenization treatments were studied. Particular attention was given to a nonuniform precipitate distribution which reflected the solute distribution in the cast aluminum solid solution. Some possible explanations for the solute distribution based on characteristics of the Al-Mn-Si or AI-Mn systems were discussed. ALUMINUM alloy 3s (aluminum plus 1.25 pct Mn) is one of the oldest and the most widely used of the wrought aluminum alloys. In spite of this fact, there are some aspects of the metallography of 3s which have not been revealed or which have not been brought to the attention of the metallurgist working with the alloy. The purpose of this investigation was to demonstrate in general how some of the fundamentals of equilibrium phase diagrams may be applied to the study of an alloy and to show specifically the origin of certain metal-lographic features of aluminum alloy 3s. It is hoped that this information can serve as a basis for solving specific problems relating microstructure to such things as mechanical properties, recrystallization, grain growth, and surface finish. Literature Survey Considering that alloy 3s contains only one alloying addition, manganese, it seems reasonable that it would have characteristics pertaining to the A1-Mn system. However, those characteristics might well be altered by the impurities in the commercial alloy, especially iron and silicon. Therefore, not only the simple binary but also more complex systems had to be reviewed. One characteristic of the A1-Mn system worthy of mention is its sluggishness, which leads to conflicting solubility data1,'2 and makes it relatively easy to supersaturate the solid solution and shift the eutectic composition during rapid solidification.3'4 Another characteristic is the strong influence which small amounts of impurities, especially iron, exert in lowering the solid solubility of manganese. Undissolved manganese is ordinarily present in an intermetallic phase, MnAl,, having an orthorhombic crystal structure. A metastable precipitating phase designated as "G" has been reported but small amounts of iron and silicon suppress this phase entirely." Raynor has established that MnA1, can dissolve a considerable amount of iron by a substitution of iron for manganese atoms up to 50 atomic pct.'" Consequently, in the Al-Mn-Fe liquidus diagram, the eutectic valley separating the primary aluminum and (Mn,Fe)Al, fields is fairly close to a constant Mn + Fe content." This is an important consideration in regulating the composition of 3s and also other aluminum alloys with high manganese additions."

Jan 1, 1956

High-type research metallurgist with approximately following qualifications: American, 30 to 45 years old. Mind-Analytical. Education-college graduate. Practical shop experience-not less than 5 years. Metallurgical experience in steel making-at least 5 years. Chemical experience-should have some chemical training. Research ability -should be the type of man who is interested in new developments or research work. No. 337. Engineer with some underground, experience who is physically able to spend a large portion of his time underground, to act as general efficiency engineer. He will have cost keeping on special work, charge of contracts, labor distribution, etc. No. 338. The services of a man experienced in flotation and familiar with the Callow apparatus are required for a short engagement in South America. No. 339. A position as surveyor and draftsman for mines in Mexico is open. Opportunity for advancement. Climate pleasant and healthful. Knowledge of Spanish required. No. 340. The Bureau of Construction and Repair, Navy Department, Washington; D. C., is in need of a few draftsmen of experience for work in connection with the development of industrial yards and shops of the Navy, under the cognizance of the Shore Establishment Division of the Bureau of Construction and Repair. Training in one of the following courses would be considered a requisite qualification:

Jan 9, 1918

By Henry P. Ehrlinger

THE Alta and St. Louis mines of the Alta Mines, Inc., produce a somewhat oxidized ore with a talc gangue that presents quite a problem in milling. For several years the mill recoveries were relatively low and there seemed to be no cure for this condition even with increasing the various collecting agents and frothers to two or three times of what they should be. The usual alibi of "oxidized ore" was given as the reason for these results and the matter stood there for some time until these investigations were started. FLOWSHEET As a brief outline of the flowsheet the ore is crushed to minus I in. in a Telsmith jaw crusher and then fed to a 64 1/2 Marcy grate mill. The resulting product from the grate mill is passed over a trommel where the coarse particles (plus 7 mesh) are returned to the grinding circuit through the classifier. The under 7-mesh pulp is passed over two Denver mineral jigs where a high grade concentrate is produced, thence over two Wilfley tables where a table concentrate is produced and about 80 pct of the oxide lead recovered. The tailings from these tables are pumped back to the classifier and after classification the 30 pct pulp density product, which overflows the lip, is passed into a series of 10 Denver economy flotation cells where a lead-copper concentrate is produced. Three products are made and shipped to the smelter termed jig, table and float concentrates. RESULTS WITH VARIOUS REAGENTS In March of this year work was started on the metallurgical problems of the mill and, as is shown in Table I, the results obtained were not too efficient. [ ] Tests were run with various reagent combinations that were recommended for ores of this nature but there was no appreciable effect on the recoveries. The grades of the flotation concentrates were reduced by the insoluble picked up and retained by these more powerful collectors and frothers. RESULTS WITH "METSO" In past work on ores of this type the use of "Metso" had improved gold and lead recoveries, but no effect on the silver and copper recoveries had been noted. To

Jan 1, 1947

HeRbert A. MeGRaw, San Luis de la Paz, Guanajuato, Mex. (communication to the Secretary*) :—Although Mr. Bordeaux prefaces his paper with the statement-that it is a general outline of practice in the Republic, many of his statements seem to be made from the view-point of a particular case, which does not always agree with general practice. For the purpose of calling attention to some of these variations, I respectfully offer the following comments: The operation of crushing and grinding is performed by so many different methods and systems that it is useless to select any one as the standard. However, primary crushing in rock-breakers followed by stamps is thus far so general that it might be so classified. Whether or not it is the best way, is open to question. Regrinding may be performed by any of the various types of Chilean mills, Huntington mills, or similar machines, or the material may be taken directly from the stamps and delivered to the tube-mills. Mr. Bordeaux's statement that " the slimes can be treated only by decantation; the new Butters slime-filter, as used in Nevada, does not seem to be successful with silver-ores," is surely an error. All over Mexico many of the purely silver-ores are being successfully handled by the Butters or similar filters, such as the Moore and the Burt filters, and a letter to the manufacturers of these filters will undoubtedly bring a list of the silver-ores now being successfully treated in this way. The statement that crushing silver-ores in solution is impossible is equally erroneous. Most modern mills crush the ore in solution, in some cases containing as much as 0.12 per cent, of KCN. I cannot for the moment recall any modern mill in Mexico which does not follow this practice. There may be some reason for it in particular instances, but, generally speaking, the practice is to crush in solution. Care in installation avoids any mechanical loss of cyanide, and the chemical loss is so small as to be negligible.

Jan 1, 1910

By H. H. Rachford, and J. D. Rice

The effectiveness of digital computing machines in making technical calculations depends on how well the work is arranged to utilize the capability of the machines. This note presents a particularly useful way of calculating hydrocarbon vapor-li.quid equilibrium in the flash vaporization (or condensation) system. The method is well suited to sequence-controlled computing equipment. It is not limited to equilibrium calculations and may be used for solution of most implicit equations in one variable. INTRODUCTION There is increasing interest in the use of electronic digital computers in research and engineering calculations. This is a fortunate and inevitable trend in view of both the increasingly extensive numerical work which is becoming a routine part of many daily production operations and growing demand for the overwhelming amounts of calculations required by newly developed numerical methods for solving heretofore unsolved problems. Machines are in many ways ideally suited to the task but of necessity present certain difficulties. for a particular poblem to be solved must often be formulated quite differently from the way it would be arranged for manual solution. This is done in order to take advantage of the inherent speed and precision of electronic computers and at the same time to limit the need for number storage to the capacity of the machine. Therefore, this note is submitted to present a general and quite powerful method of finding solutions of the frequently encountered implicit equation: F(x,y1,y2,...ya)=0.......(1) where the root, x, is to be found for a given set of y1, ... yn.. The procedure is well suited for use with computing machines, for it usually requires but little storage or programming beyond that necessary to evaluate F. HYDROCARBON EQUILIBRIUM The method is described in terms of the problem it was designed to solve, i.e., the calculation of hydrocarbon vapor-liquid equilibrium in flash vaporization. Given the composition of a hydrocarbon mixture and appropriate values of the equilibrium ratios K, to find the phase ratio and compositions in a closed system: let z, be the mol fraction of the i-th component in the mixture. If K, is the ratio yl/xl, where y, and x,

Jan 1, 1952

By R. G. Ward, D. R. Gaskell

Using the maximum bubble pressure technique, the densities of iron silicates at 1410°C have been measured blowing helium, nitrogen, and argon. By ensuring equilibrium between the melt and the blowing gas with respect to oxygen potential and by minimizing tempcrature cycling of the furnace, iron precipitation in the melt has been prevented. Thus the previously reported effect of blowing-gas composition on the densities of the melts has been eliminated. Consideration of the oxygen densities of the melts gives an indication of the structural changes accompanying composition change. The density-composition relationship of iron oxide-silica melts in contact with solid iron has been the subject of several investigations1-7 and considerable disparities exist among the various results obtained. Of these investigations, all except one5 have employed the maximum bubble pressure method. In the most recently reported of these investigations1 the density-composition relationship obtained blowing nitrogen differed from that obtained blowing argon. The measured densities obtained under nitrogen were greater than those obtained under argon, the difference being a maximum at the pure liquid iron oxide composition and decreasing with increasing silica content. This observation rationalized the disparities existing among the results of the earlier investigations, showing that two lines, one for nitrogen and the other for argon, could be drawn to fit all the earlier results. No explanation for this phenomenon could be offered. Chemical analysis of rapidly quenched samples of melt for dissolved nitrogen, and direct weighing measurements, excluded solution of nitrogen in the melt from being the cause of the increase in density. The range of blowing gases was extended by Ward and Hendersons who measured the density of liquid iron oxide bubbling helium, nitrogen, neon, argon, and krypton. The measured density was found to decrease smoothly with increasing atomic number of the bubbling gas. The work reported here is a continuation of the program initiated by Ward and Sachdev7 to study the densities in multicomponent melts in which the iron oxide-silica system is the solvent. As such it is necessary to explain or eliminate the anomalous densities of iron silicates under different atmospheres, and the present rede termination was carried out towards this end. EXPERIMENTAL The maximum bubble pressure method of density determination was again employed and the experimen- tal apparatus used was essentially the same as that used by Ward and Sachdev.7 A molybdenum-wound resistance furnace heated an ingot iron crucible of internal diameter 1 in. containing a 2-in. depth of melt. The bubbling gas was blown through a 1/4 -in.-diam mild steel tube onto the end of which was welded a 2-in. extension of 1/4 -in.-diam ingot iron rod, drilled out to 5/32 in., and chamfered to an angle of 45 deg. The blowing tube was introduced to the furnace through a sliding seal and its position was controlled by a vertically mounted micrometer screw which allowed the depth of immersion to be determined with an accuracy of ± 0.01 cm. A Pt/Pt-10 pct Rh thermocouple was located below the crucible and temperature control was effected initially by means of an on-off controller and later by a saturable core reactor. The bubble pressure was determined by measurement of a dibutyl phthalate manometer using a cathetometer. PREPARATION OF MATERIALS Iron oxide was produced by melting ferric oxide in an inductively heated iron crucible in air. The liquid was quenched by pouring onto an iron plate. Silica was prepared by dehydrating silicic acid at 650°C for 12 hr. RESULTS Before any measurements of the density of a melt were made, the density of distilled water at room temperature was measured bubbling helium and argon. Both gases gave the density as 1.00 ± 0.01 g per cu cm which showed that the density of the manometric fluid (dibutyl phthalate) was not affected by contact with the blowing gas. With the furnace controlled by an on-off temperature controller an attempt was made to measure the density of pure liquid iron oxide by bubbling argon. The furnace atmosphere gas and bubbling gas were dried over magnesium perchlorate and deoxidized over copper turnings at 600°C. It was found that the pressure required to blow a bubble at a given depth increased slowly with time, and thus it was impossible to obtain a unique value for the density of the melt. Inspection of the blowing tube after removal from the furnace showed that rings of dendritic iron had precipitated from the melt onto the immersed part of the tube. This is shown in Fig. l(a) where the various "steps" correspond to different depths of immersion. The precipitation of iron was considered to be due to one or both of two possible causes: i) The composition of the liquid iron oxide is that of the liquidus at the temperature under consideration and can be expressed by the equilibrium

Jan 1, 1968

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904

By H. C. Brown

SINCE 1934 the steel industry has been utilizing the spectrograph for supplementing wet chemical analysis in the production control of electric and open hearth furnaces. This means of control made great strides during the war years because of the general acceptance of the spectrograph and the increased emphasis that was placed on rapid control methods. However, in the post war era, with the demand still on increased production, it became apparent that a still more rapid and economical means of production control was needed. Since the spectrograph had been used mostly in the analysis of low alloying and residual elements, it also became apparent that equipment was needed to extend the spectrographic technique to the analysis of the high alloying elements in stainless steel. For these reasons, companies manufacturing spectrographic equipment were prompted to start development work on direct reading instruments. In June 1949, the Applied Research Laboratories of Glendale, Calif., announced that a direct method of spectrochemical analysis for stainless type steels had been developed. This paper will describe the use of the Applied Research Laboratories Production Control Quantometer in the quantitative control of stainless, silicon, and plain carbon steels being made at the Butler Pennsylvania Div. of the Armco Steel Corp. The Armco Butler Div. has one 70-ton electric furnace and six 150-ton open hearth furnaces. The electric furnace is employed in the making of all types of stainless steel and the open hearth furnaces are used for the production of silicon, wheel, and plain carbon steels. The ARL quantometer was purchased primarily for the purpose of controlling the steelmaking in the electric furnace, but its use has been extended for the analysis of final tests (ladle tests) on a number of different types of stainless, silicon, and plain carbon steels. Because of this additional work by the quantometer, substantial savings in manpower and time have been realized by the laboratory. In the analysis of a set of preliminary tests from the stainless steel furnace, approximately 40 min in laboratory time are saved due to quantometric analyses. Despite the fact that more specialty grades of stainless steel are being made in the electric furnace, the average tons per hour have been increased since the quantometer was put into operation. Specialty grades require more furnace time than regular commodity grades of stainless steel. The installation of the ARL production control quantometer was completed on March 13, 1952. By May 1, 1952, the instrument was calibrated for nickel, chromium, manganese, silicon, and molybdenum, which are the elements necessary for the production control of the stainless steel furnace. Within the following month, training of personnel on the quantometer was achieved and a study of the accuracy of the instrument showed that the results obtained were sufficiently accurate for control purposes. Therefore, on June 11, 1952, the quantometer was placed on production control for all types of stainless steels. Starting September 11, 1952, the instrument was gradually placed on ladle analysis (final tests) as the analytical curves were refined and additional curves were drawn. The quantometer has been relatively free of breakdowns since placing it on production control. The samples from only one stainless steel heat have had to be analyzed by wet chemistry because of instrument trouble. The previously existing heat-time record was also bettered by 15 min on a commodity grade of 18-8 stainless steel. Scope of Control In general, the quantometer determines all elements necessary for the production control of all types of stainless steel heats and for the ladle analysis of various types of stainless steel heats. It is also used in reporting final results for silicon, manganese, chromium, nickel, molybdenum, tin, copper, and aluminum on all silicon steel grades and manganese, chromium, nickel, molybdenum, tin, and copper on several plain carbon steel grades. Table I shows the elements and the concentration ranges of these elements in the various types of stainless, silicon, and plain carbon steel that are determined on the quantometer. A study of the results obtained on ladle test samples of stainless steel types 410, 430, 430 Ti, 446, 301, 302, 304, 304L, 305, and 17-7 PH will be discussed. Also included in the study are the results obtained on ladle test samples of a number of silicon steels. Apparatus In order to take full advantage of the potentials of the production control quantometer, the unit has been placed in an air-conditioned room with relative humidity control. The temperature is maintained at 73'22°F and the humidity at 45&5 pct. The air conditioning serves as a precaution to minimize the amount of adjustment and calibration needed during operation. It also reduces contaminating fumes and dust and thereby lessens the necessity for maintenance on the equipment. The quantometer is composed of three units: the high precision multisource unit, the 1.5 meter vertical spectrometer, and the console. The source unit supplies excitation conditions varying from spark-like discharges to arc-like discharges. The voltage to the source unit is supplied by a motor-generator

Jan 1, 1955

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915