Search Documents

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By NEWTON B. KNOX

CHILEAN mining in the public mind is rightly associated with copper. Chuquicamata with its great hill of copper-bearing granodiorite as well as Sewell and Potrerillos with mineralized volcanic necks together can supply a good proportion of the world's normal necessities of that metal. Chile is an extremely long and narrow country, averaging only 109 miles wide. Its eastern frontier is the Andes and it is on the western slopes of these mountains that the great copper deposits have been discovered. West of the Andes a great longitudinal depres sion has permitted accumulation of nitrates and other soluble salts in the arid north; in the north center it is hidden by a series of cross ranges, but in the center a moderate rainfall makes it the country's most important agricultural region. In the south this depression is drowned and gives rise to a series of straits and fiords. This enormous cleft in the earth's crust is separated from the sea by a coast range of moderate elevation which in the south is represented by a series of islands and mushroom-shaped peninsulas

Jan 1, 1945

By C. W. Robinson

Transportation is the minerals business. Once upon a time the geologist, the engineer and later the metallurgist reigned supreme, but the leading role in mineral development today is the economist-especially the transportation economist. Obviously this trend is more important for large volume, low value mine-to-market movements of such commodities as iron ore, phosphate, potash, coal and petroleum. But, transportation is of sufficient importance to all mining activities to be included in forward planning. Civilization has been influenced by transportation developments to an extent little understood or appreciated. Although industrialists are capable of intelligent historical analysis of this phenomenon, too frequently they have failed to project, or anticipate those changes in transportation techniques which will influence the pattern of industrial growth.

Jan 1, 1971

By W. E. Gaby

THE form of dip chart here presented for the use of the profession was devised by the author when he was confronted with a particularly heavy job of geological section making and. did not have any of the usual tables or charts at hand. This was at the property of the Teziutlan Copper Co. in Puebla, Mexico, where the orebodies are much faulted and lie conformably with a slightly inclined and. much folded schist. Because of the low dip and the folding of the orebodies, the engineering, and geological data respecting them were best represented on vertical cross-sections quite closely spaced. A less finished form of the chart was published in the Mining & Scientific Press of Aug. 6, 1921, with an explanation of its use. I have checked the new drawing for accuracy against the calculated table given, and constructed an explanatory diagram beneath. As some geologists are accustomed to using the table, I have included it, since no advantage is obtained by mere interpolations from the chart to get the required angle, except as it gives a mental picture of this angle. The chart gives a more rapid and much easier solution when cases multiply so that it becomes desirable to eliminate the tedious manipulations of a separate protractor. In fact, using the parallel ruler as des-cribed, it is not even necessary to make note of the angle sought. It is brought out graphically, leaving the mind free to note the correlations. The chart itself may be made more convenient by reproduction on celluloid with a slot running on the zero line of the protractor.

Jan 9, 1922

By W. R. Hansen, F. W. Boulger

Twenty-nine laboratory steels were studied to determine the effects of composition and ferrite grain size on drop-weight and Charpy V-notch transition temperatures. The experimental steels covered the following ranges in composition.. 0.10 to 0.32 pct C, 0.30 to 1.31 pct Mn, 0.02 to 0.43 pct Si, md nil to 0.136 pct acid-soluble Al. Although most of the data were obtained on hot-rolled samples, some plates were heat-treated in order to cover a wider range in ferrite grain size. The experimental data were used for a multiple-correlation analysis conducted with the aid of an electronic computer. The study showed that carbon raises and that manganese, silicon, aluminum, and finer ferrite grains lower both drop-weight and Charpy transition temperatures. Quantitatively, variations in composition and grain size have a more marked effect on V15 Charpy transition temperatures than on the drop-weight transition temperature. Useful correlations were found between transition temperatures in drop-weight tests and those defined by seven different criteria for Charpy tests. Evidence was accumulated that the conditions ordinarily used for drop-weight tests are more severe for 1-1/4-in. -thick plate than for 5/8- to 1-in. -thickplate. PROJECT SR-151, to study quantitatively the effects of metallurgical variables on performance in the drop-weight test, was established by the Ship Structure Committee late in 1958 on recommendation of the National Academy of Sciences, National Research Council. This project was initiated as a result of the increasing use of the drop-weight (nil-ductility) test in predicting the ductile-to-brittle behavior of steel. Qualitative data indicated the drop-weight was not as sensitive to metallurgical variables as the Charpy V-notch test. Furthermore, the available information indicated that the drop-weight test did not show the superiority of killed steels over semikilled steels reflected by Charpy tests. This difference in sensitivity to brittle fracture is considered important because the drop-weight transition temperature has been reported1 to correlate better with service-temperature failures than the V-notch test does at a constant energy level. Therefore, this project was concerned with establishing quantitatively the effects of metallurgical variables in the drop-weight test. For comparison, Charpy V-notch data were obtained for the steels investigated. This paper summarizes the results of the investigation. Most of the steels used for the study were made and processed in the laboratory. However, some tests were also made on commercial killed steels available from Project SR-139 (SSC-141). During the course of the investigation, data were obtained on the effects of carbon, silicon, manganese, and aluminum on transition temperatures of drop-weight and Charpy specimens. In addition, the effects of heat treatment which changed the ferrite grain size and the transition temperatures were also investigated. Finally a few exploratory studies were made on commercial killed steels to evaluate the effects of plate thickness, grain size, and heat treatment on the performance of drop-weight specimens. EXPERIMENTAL PROCEDURES Preparation of Materials. A total of twenty-nine 500-lb induction-furnace heats were made and processed in the laboratory for the investigation. Carbon, manganese, silicon, and aluminum contents were systematically varied. Melting and rolling techniques proven satisfactory in a previous project2 were used as a guide for the current investigation. Composition. The composition of the twenty-nine laboratory heats made for this project are given in Table I. The steels are divided into three groups. The first group consists of ten aluminum-killed steels similar in composition to Class C ship-plate steel. The second group consists of ten semikilled or Class B type steels. In both of these groups the carbon and manganese contents were intentionally varied over a wide range. This wide range in composition was helpful in obtaining quantitative data from a limited number of steels. The primary purposes of these two groups of steels was to determine the effects of carbon, manganese, and deoxidation practice. In addition, one steel in each group (Steels 2-2 and 9-2) were made about 1 year after the start of the program in order to check consistency of melting practice. The third group of nine steels listed in Table I was intended for studies on the effects of silicon and aluminum. In eight of these steels carbon and manganese were held relatively constant at levels of about 0.2 and 0.8 pct, respectively, while silicon and

Jan 1, 1963

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Walter Lee Brown

One of the characteristic steps in the march of modern scientific progress is the substitution of improved time-saving and labor-saving appliances for the antiquated and, in most cases, inconvenient forms of chemical and physical apparatus used by the earlier experimenters. This fact is strongly impressed upon us when we consider the question of the employment of illuminating-gas as a source of light, heat and power. Concerning its value as a light-producer, let the record of the past three-quarters of a century speak for itself. As a factor for power, we have evidence of its efficiency in the shape of the gas-engine. But its adaptability as a medium of heat, is the feature to which I wish to call attention, and in a special direction, viz., the assaying of ores. Gas assay-furnaces have been known and used for some years, but not to any very great extent, in this country at least. Therefore no apology on my part is required for the description I now give of a complete gas assaying-plant. The illustration accompanying this paper is a faithful representation of the group, as it was designed by, and arranged for myself, and appears in actual running order in my laboratory to-day. Its duty is to do roasting, crucible-fusion, scorification and cupellation. The furnace at the left is for roasting sulphurets or other ores for experimentation or actual work. It is what is known as a Fletcher No. 163, and consists of a fire-clay body strapped with sheet-iron bands, and a burner (No. 16, Fletcher). The opening at the top

Jan 1, 1885

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.' As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

At a large meeting of the members of the American Fund for French Wounded it which Mr. Franklin D. Roosevelt presided and at which Mrs. B. Girault Lathrop, President of the Paris Administration A. F.F. W., gave a most interesting address, special rows of seats were reserved for the members of the W. A. A. I. M. E. Those who were unable to be present will be glad to hear that Mrs. Lathrop complimented our organization on having supplied the largest dispensary operated by the A. F. F. W. and the Red Cross in northern France. The A. F. F. W. is going to erect an American Memorial Hospital at Rheims and it is hoped that the one hundred beds in the hospital will be endowed in memory of the men who gave their lives for the liberty of the world. It will be possible not only to endow beds, for which sums of $6000 each are needed, but also to give, as. memorials, sun- parlors at a cost of $10,000 each, two roof gardens at $5000 each, a laundry at $10,000 and a garage at $10,000. The New York Section has undertaken to endow a heel in memory of members of the A. I. M. E. who gave their lives in the Great War. Perhaps other Sections or groups of Sections may wish to do the same thing, or if no other Section cares to assume so much responsibility possibly individuals may like to join the fund already growing in New York, in which case they should send their contributions to Mrs. W. Y. Westervelt, 1 Lexington Ave., New York, N. Y.

Jan 6, 1919

By R. H. Lee

So far as I am aware the references to the " kerosene blow-pipe" in the Transactions comprise only a skeptical opinion from Mr. Witherow (ix., 70), and accounts of the use of the blow-pipe by Mr. Witherbee (xiii., 675) and Mr. Gayley (xiv., 779), together with brief remarks by Mr. Weeks and Mr. Kennedy on Mr. Witherbee's paper. The subject can scarcely be considered novel, in view of these references, yet it is not so far exhausted that an additional account of the successful application of the blow-pipe would be out of place, especially if accompanied with some new details and a drawing of the apparatus itself, showing its simplicity and safety. Some time ago, owing to a variety of causes, my furnace was working very badly, the troubles culminating suddenly one morning in a chilled hearth, solid from the bottom to the tuyeres, with the exception of a narrow passage-way from above to the cindernotch, which remained open. Through this we continued to flush and cast, with the prospect of a long and troublesome siege, in working down to the iron-notch. At the end of two days matters had not greatly improved, and we seemed no nearer the desired result than on the morning of the chill, when, at the suggestion of Mr. Farrell, of Glamorgan, I decided to use the coal-oil blow-pipe; the intention being to cut a hole from the iron-notch up to the tuyeres, and then let the furnace melt out the chilled mass. In four hours from the time of starting, the hole was made and

Jan 1, 1887

George H. Abeel, Hurley, Wis. (communication to the Secretary) : Doubtless Mr. Boss did not mean to be understood as saying that the dikes of this range are everywhere overlaid with iron-ore. I know of places where the dark, massive dike is found near the surface, but no ore is found on it. And his statement (p. 557) that a wherever the slightest inclination is shown it is always to the east," should be modified to " usually." There are several instances of a westward pitch, e.g., at the Palms, Newport and Odanah properties, and also at the Montreal mine, where we encountered in the ore a small dike pitching west. Mr. Boss's statement (p. 559) that. the ore of the Pence mine lens " has all been removed from the Pence and Father Hennepin lands, and practically from the Montreal property, and is now being wrought by the Montreal Mining Company on the ' Sec. 33' property," does not convey the exact state of the latter company's operations. We are still mining ore on the Montreal property from the lens referred to, and expect to continue doing so for some little time to come. On the other hand, we are getting a shaft down to the ore on the " See. 33 " property, but ye have not yet encountered the dike. This can hardly be considered as working the ore. I do not understand upon what evidence Mr. Boss can consider the correctness of a previous hypothetical location of the dike to have been established " within 2 feet," when the dike has not yet been reached. Possibly he has been misled by hearsay reports.

Jan 1, 1898

Discussion of the papers of FREDERICH LAIST and HAROLD W. ALDRICH, FREDERICH LAIST and F. F. FRICK, W. L. AUSTIN, and STUART CROASDALE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletins No. 91 and 92, July, and August, 1914. R. C. CANBY, Wallingford, Conn. (communication to the Secretary*). -Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and coke, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata., it might be of interest to refer briefly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911, I. gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcome after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable-chlorine, clue to the imperfect conversion of the subchloride to suboxide, as well as that clue to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted With the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These, fumes had a peculiarly suffocating effect, so that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been clue to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 11, 1914

By A. McLean, D. W. Gomersall, R. G. Ward

An experimental study has been made of the solubility of nitrogen in liquid iron and liquid Fe-C alloys using levitation melting and a rapid quenching device. Iron alloy droplets were equilibrated with nitrogen gas at 1 atm pressure, quenched, and analyzed. Previous techniques for studying the Fe-C-N system have produced data which me in marked disagreement. This disagreement is due largely to errors caused by reaction between the molten alloy and the crucible material. With the levitation procedure, errors from this source have been eliminated and precise solubility data obtained for temperatures between 1450° and 1750°C. C-N interactions in molten iron have been expressed in terms of first- and second-order free energy, enthalpy, and entropy parameters. ALTHOUGH the solubility of nitrogen in iron base alloys is in general small, the effects of nitrogen on the properties of steel may be quite profound. For most purposes nitrogen in finished steels is undesirable, particularly in the low-carbon grades, since on cooling to room temperature the solubility limit of nitrogen in the steel may be exceeded and this can lead to embrittlement and loss of ductility on aging. On the other hand, nitrogen can improve the work-hardening properties and machinability of steels while in certain stainless grades nitrogen is important in order to stabilize the austenite phase. It is, therefore, desirable that one should be able to predict the solubility of nitrogen in liquid iron alloys. To do this, information is required concerning the interactions between nitrogen and the various alloying elements which may be present in liquid iron. There have been several investigations of these effects in recent years1"7 and the interactions between nitrogen and many elements dissolved in liquid iron are now known to a high degree of precision at steel-making temperatures. Unfortunately, a number of iron alloy systems which are of interest in steelmaking have been difficult to deal with by the experimental techniques generally used for this type of investigation. Among the most important of these are the Fe-C alloys. In the past, two methods have been widely used for determining nitrogen solubilities: the Sieverts' technique, in which the amount of nitrogen required to saturate a given mass of liquid metal at a particular temperature and pressure is measured volumetrically, and the sampled-bath technique in which liquid metal held in a crucible is equilibrated with a gas phase containing a known partial pressure of nitrogen, and samples drawn from the melt are quenched and analyzed. These two methods have been discussed in detail elsewhere.5,8 With the Sieverts' technique, errors may be introduced from the following sources: i) Gas adsorption on metal films which have condensed on the cooler parts of the reaction chamber. ii) Uncertainty in the determination of "hot volume" calibrations. iii) Crucible-melt interaction, particularly if a gaseous reaction product is formed or if the melt becomes contaminated with material from the crucible walls. The sampled-bath method may also suffer from errors due to reaction between the melt and the crucible material. In addition, there is the possibility that gas may be lost from the sample during solidification and cooling. In the present investigation, the solubility of nitrogen in liquid iron alloys has been studied by means of a new technique based on the use of levitation melting equipment and a rapid quenching device. In addition to the fact that problems of the type outlined above are avoided, this particular approach has the following advantages: i) The high-frequency current induces vigorous stirring within the levitated droplet so that gas-metal equilibration is rapidly attained. ii) The gas phase surrounding the melt can be changed very quickly and is easily controlled. For example, a droplet may be levitated in helium, deoxidized in hydrogen, equilibrated with nitrogen, and quenched, within a period of 15 min. ii) Melts can be readily under cooled or superheated, thus extending the effective temperature range of an investigation and allowing temperature-dependent data to be determined with a high degree of precision. Excellent reviews of levitation melting techniques and their application to physical-chemistry studies at high temperature have been published recently by Jenkins et al.,9 Peifer,10 and Rostron.11 In the present investigation a levitation melting technique has been used to obtain data for the solubility of nitrogen in pure liquid iron and liquid Fe-C alloys at temperatures between 1450° and 1750°C. The solution of nitrogen in liquid iron can be described by the reaction:

Jan 1, 1969

By A. A. Beard

ABOUT three years ago, I. L. Dunn, of Marietta, Ohio, found that wells could be cleaned by blowing with compressed air; this method has been used with great success on many wells in the Marietta, Ohio, district, where compressed air is being used to increase production, by forcing oil through the depleted sands. About a year ago, the process was successfully used to clean out wells in the Lenapah pool in Oklahoma, where an air plant had been installed, under the supervision of I. L. Dunn. Wells from 900 to 1000 ft. deep, with 40 ft. of sand and cavings in them, were cleaned out in from two to three days. The use of this process had, so far, been limited to properties using the Smith-Dunn process, where compressed air, under suitable pressure and volume, was available. For other properties, a portable compressor seemed essential; this was built and successfully demonstrated by Mr. Dunn, for the Tidal Oil Co. in September, 1924. The process of cleaning out with air has been described.1 It consists of lowering the tubing into the well, with a shoe or nipple of heavy pipe substituted for the perforated anchor on the bottom. Into the tubing, compressed air is introduced through a rotary swivel hose at the top, or by means of swing connections. The tubing is lowered to the top of the cave to be cleaned out, several barrels of water are put into the hole, and the compressed air is turned on. This blows out the material between the casing and the tubing, the tubing being lowered as the material is removed.

Jan 9, 1925

By D. R. Mitchell

FOR the second consecutive year, attendance at the Coal Division sessions far exceeded exoectations. Those in charge were continually faced with problems of finding seats and space for attending members. 115 seats were set - II~ for the annual luncheon meeting of the Division and approximately 175 members showed un. Since the hotel management would not serve more than the 115 it meant that 60 members were forced to eat elsewhere. This created hard feelings with some members. How- ever, officials of the Division were not able to obtain in advance any indication of this overflow crowd, but are suggesting to the New York Office that some means other than ticket sales be adopted to obtain an estimate of Division luncheon and dinner attendance. Members could be circularized prior to he meeting or they could be checked when registering as to the events they expect to attend. Under the inspiring leadership of Cadwallader Evans, Jr., Chairman, the Coal Division had a phenomenal growth during the year. Reporting at the luncheon meeting, Newel1 Alford stated that approximately 190 new members had been obtained. A few more years of continuing increase at this rate will make the Coal Division one of the largest Divisions in the Institute.

Jan 1, 1944

By Andrew S. McCreath

The manufacture of pig iron for conversion into steel by the Bessemer and open-hearth processes, is now one of the most important industries of the United States. It is necessary that iron intended for this purpose should be very pure, and especially must it be comparatively free from phosphorus. Great care must therefore he exercised in the selection of proper ores, flux, and fuel. Only such ores as are practically free from phosphorus can be used, and pure fuel is as much a necessity as pure ores; though hitherto iron men have paid comparatively little attention to this point. During the course of my work as chemist for the Second Geological Survey of Pennsylvania, I' had occasion to examine some of the bituminous coals of the State fix phosphorus, and the results obtained are so interesting that I venture to present them to the notice of the members of the Institute. The coals are arranged in geological order according to the different beds, and the table shows the percentage of phosphorus in the coal and also in the coke. The greatest number of specimens have been selected from the Pittsburgh bed, because it is the principal coal-bed of Southwestern Pennsylvania, and most of the mineral fuel which is mined along the Youghiogheny and Monongahela rivers, to be used in the coke ovens of the Connellsville region and in the blast furnaces and mills of Pittsburgh and its vicinity, and to be shipped to Western and Southern markets, comes from this bed. It will be noticed that many of the specimens examined contain

Jan 1, 1880

The Colorado School of Mines, Golden, Colo. M F Coolbaugh, President. Since 1906 the School of Mines has issued a journal, known as the Quarterly of the Colorado School of Mines, which carries many articles on matters of general interest as well as other articles of a technical nature There is no regular subscription price to the School of Mines publications Anyone interested in back numbers should write and find out the conditions under which individual copies may be obtained, whether a price is set on them or whether they are free Some back numbers are not now available but efforts will be made to supply copies from the files of alumni or other friends of the School Vol 23, No. 3 of the Quarterly (July, 1928) is an index of the publications complete from July, 1906 to July, 1928. A selected list of the technical articles appearing in the Quarterly is given here: Vol 3, No. 3, Rare metals. uranium and vanadium, by H. Fleck (1909), vol 3, No 4, Tungsten in Colorado, by H R Van Wagenen, vol 4, No 3, Preliminary report of the radioactivity of the carnotite of southwest Colorado, by H Fleck and W. G Haldane (1909), vol. 8, No 1 (1913), Some recent developments at Leadville, by G. M Butler, vol 8, No. 3, Physiography of

Jan 1, 1933

By Clarence Zener

It is customary to regard the stress-strain relation as consisting of two parts, thc elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.l,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwir-kung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants---e.g., Young's modulus— upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective. of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of anelasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1947