Search Documents

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

By Arthur Mitchell

POSSIBLY in no other of the non-ferrous mining districts of this country has the use and develop-ment of mechanical loaders been carried to such an extent as in the "lead belt" of Southeast Missouri. It has become apparent to the four mining companies in the district that it is imperative to apply satisfactory mechanical methods to the chief remaining stage of the entire operations-mining, milling, smelting and refining-in which manual labor is still largely used to handle material in process. With increasing wages and with the reduction of the metal divisor by the extension of mining into lower-grade orebodies, the shoveling cost per ton of lead produced has become relatively so large that in an effort to reduce it there is ample justification for considerable capital expenditure. Hand shovelers load about 18 tons of ore per shift and the average grade is less than five per cent. lead. Further, the ore is relatively heavy, about 21 cu. ft. to the ton when broken, and is often so coarse and so closely compacted after shooting that it requires much more block-holing, sledging, and muscular effort to shovel than, for example, does the cherty and more granular ore of the Joplin district or the finer ore in the headings of a drift mine. No mining company desires to pay for mere back muscles if it be economically feasible to avoid it, and labor saving machinery should be susceptible of operation by older employees, who are no longer capable of the more strenuous manual occupations.

Jan 4, 1923

By W. H. Adams

Shortly after becoming one of the van-guard of mine-developers in the State of Virginia, during the year 1883, I called the attention of the Institute to certain deposits of pyrites, which have been largely worked since. In all cases these deposits are covered with iron-ore (limonite), extending 40, 50 or 60 feet from surface to water-level. The several classes of brown iron-ores are found almost continuously along a prominent ridge of mineral-bearing slates, which can be traced from the James river northeasterly to the North Anna, the Rappahannock and the Potomac rivers, crossing the counties of Louisa, Spottsylvania and Stafford. Outcrops are plainly discoverable from end to end of this belt, also, in places, to the right and left of it, and at intervals there are evidences of workings, some of them for known purposes and others of unknown age and meaning. These old workings have an interest aside from the minerals they may contain or may have yielded. I have been engaged during the past five years in the collection of facts concerning them, which might determine definitely the site of those iron-furnaces, placed by tradition within reach of " the towne called Germanna," which were the first ever built in this State or on this continent. The events which led to the establishment of this important industry are sufficiently narrated in a paper written by Mr. R. A. Brock, Secretary of the Virginia Historical Society, and printed in the Proceedings of the National Museum, 1885, page 77, from which I quote the following : " To Virginia, the first of the English settlements in America, belongs the honor of inaugurating within her limits, as a colony, that most important industry, iron manufacture. "The London Company contemplated a variety of manufacturing enterprises from the very beginning of its authority; prominent among them was that of iron. In 1610 Sir Thomas Gates testified before the council of the Company at London, that in Virginia ' there were divers minerals, especially iron-oare,' lying upon the

Jan 1, 1892

By Roy W. Wright

Introduction The title of my paper is satisfyingly broad and allows me to touch lightly or dwell at length on virtually any aspect of mining, while endeavouring not to trespass on the subjects of other papers to be presented. However, at this stage in our world history when for the first time we are beginning to take conservation and the welfare of future generations more seriously, I want to concentrate mainly on the question of whether or not there will be the resources of minerals available to sustain mankind's progress in the generations ahead. Metals and the Population Problem The supply of raw materials is of course only one of the fundamental problems that will face future generations: if we assumed that the world population would continue to increase at the present explosive rate, then I believe we can say with certainty that other fundamental problems of much greater significance would arise long before a shortage of raw materials - or other substitutes -had any impact on the progress of mankind. Thus, I must start this paper with the assumption that some equilibrium in population will be arrived at before these other problems overwhelm the world. Will the Metals Run Out? At the 75th Anniversary Meeting of this Institute in March, 1947, Clinton H. Crane, President of St. Joseph Lead Co., prophesied that for the next 100 years there would be enough copper, lead and zinc for every essential need. He defined a need as essential where the qualities of the metal in that use were irreplaceable. Today, except for one or two cases such as lead in lead-acid batteries, few metals have qualities that cannot be provided either by another metal or by another material. It is more a question of what the engineer or manufacturer is prepared to pay for special qualities as compared with using cheaper materials and perhaps a less satisfactory design.

Jan 1, 1971

By Robert B. Fulton

It is a pleasure to talk to you about the world economics of industrial minerals on this occasion of AIME's 100th anniversary. In order to fit this topic into the time and tenor of such a session as this where you are hearing subjects equally broad in scope one after the other, I will deal with the subject through the medium of eight minerals selected to illustrate import- ant economic factors. I must admit to some bias in the selection, since I picked personally familiar ones to elucidate facts of life in the industrial minerals business. It is a very interesting field, different in many respects from metals and certainly far different from petroleum. The minerals chosen are celestite, diamond, fluorspar, salt, sulfur, ilmenite, rutile and zircon. Celestite The market for celestite is mainly in the U. S. where it is consumed in the manufacture of strontium compounds for red-colored flares and other pyrotechnics, for the production of electrolytic zinc, for glass manufacture, and for the manufacture of ceramic ferrites. Smaller markets exist in Europe and Japan. Production comes from England, Mexico and Spain, and a new mining operation is being started in Nova Scotia. There is no significant production in the U. S. nor in the other principal consuming countries, except England; so it is mainly an international commodity. Celestite illustrates many of the factors important in the economics of industrial minerals. To have a marketable product, grade and freedom from deleterious elements are important for materials used by the chemical industry. In the celestite used to make strontium nitrate, calcium is the most objectionable of the commonly associated cations. Selling price is adversely affected because nitrate manufacturing costs are greatly increased if calcium is pre sent, hence less can be paid for the raw material. Meeting specifications can add significantly to the vendor's cost; hence a balance must be struck between the producer's capability and the consumer's requirements, permitting a reasonable profit for both. Sizing of industrial mineral products is often important to the consum-

Jan 1, 1971

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By W. H. Bassett

BERYLLIUM was discovered in 1798 by Vauquelin and the metal was first produced by Wohler in 1828 about a year later than his production of metallic aluminum. Beryllium remained dormant until about 1920 when the production of the metal by the electrolysis of a molten bath was carried out by Stock in Germany, closely followed by Dickinson in the United States and by Vivian in England. This may not have been the first time the electrolytic method was thus used but was the beginning of present-day methods. I believe the first commercial attempts in this country started with the Kemet Laboratories about 1924. Siemens & Halske in Germany were working on the same problem at about the same time. The work of the Kemet Laboratories was transferred to the Beryllium Company of America and later to the Beryllium Development Corporation. In 1926 1 made a considerable study of the beryllium¬copper alloys, using beryllium purchased from the Beryllium Company of America, and read a paper on this subject at the February, 1927, meeting of the A.I.M.E. However, I failed at that time to discover the properties of precipitation hardening which such alloys have in a very marked degree. After this publication the work on beryllium-copper alloys rested awhile. One cause for this was the difficulty of securing a supply of beryllium-at least at what might be considered a reasonable price. In 1926 the price was $200 per lb., a figure which held about the same both in this country and in Germany until the beginning of 1932, when it was offered here at $50 per lb. if taken in the form of a copper alloy which carried about 121/2 per cent beryllium. Somewhat later the 121/2 per cent alloy dropped to $25 per lb. of beryllium contained, which is the present price. Promise is made that with a greater consumption, production on a larger scale warrants a reduction in price to $10 per pound or less.

Jan 1, 1933

By AIME AIME

CHARLIE WARNER, Chairman of the Petroleum Division, is no stranger to the problems of the oil industry or to those of the Petroleum Division, after more than 25 years of experience in locating and producing oil and more than 22 years of membership in the Institute. He was born at Jefferson, N. Y.. April 27, 1894, and educated in the public schools of New York State and at Cornell University where he studied geology and allied sciences from 1913 to 1917 and received a B.A. degree. Immediately upon completion of this training, he was employed by the Empire Gas & Fuel Co. as a field geologist in Oklahoma and Kansas. Two years later he became district geologist for the Emerald Oil Co. in Oklahoma and Kansas, and in 1920 he rejoined the Empire Gas & Fuel Co. in the capacity of district geologist in Oklahoma. In September of 1921 he began his association with the Houston Oil Co. of Texas. He was district manager for the company in the Mid-Continent area until 1932 when he was transferred to the head office at Houston, where he became superintendent of the land and lease department in 1934 and was elected a director of the company in 1941. In these capacities, and also as petroleum engineer for the company, he keeps in intimate touch with all phases of field activity and with the regulation of the industry by State and Federal agencies.

Jan 1, 1943

By D. I. Bardos

The occurrence of Laves phases (AB,) in various binary alloy systems has been reviewed in recent papers.13 Iron forms Laves phases with Sc-, Ti-, V- and Cr-group elements. However, two of the corresponding Laves phases with cobalt, namely MoCo, and WCo,, are missing. Nickel forms binary Laves phases with Sc and Y, but not with any Ti-, V-, or Cr-group element. These conditions are schematically illustrated in Table I. That electron concentration is a significant factor in determining which type of Laves phase is formed in a given case was recognized long ago by Laves and Witte,4 This concept has been more recently applied to Laves phases formed by transition ele-ments. It now appears that the average electron concentration (average number of electrons per atom outside of the closed shells of the component atoms) may be an important factor also in determining whether or not a Laves phase can occur at all in a given system. As shown in Table I, in the transition element systems considered Laves phases are absent at electron concentrations of 8, or larger (to the right and below the double line in Table I). These absences clearly cannot be accounted for on atomic size considerations, as evidenced by the many inconsistencies apparent in Table 11. While the ideal radius ratio for Laves phases is 1.222, in the systems which do have Laves phases the ratios of CN 12 radii range from 1.10 to 1.46. The consistent absence of Laves phases at RA/RB< 1.10 might be attributed to the low values of these radius ratios. However, Table II shows that absences also occur irregularly throughout the radius ratio range covered. In a previous paper7 it was concluded that, in transition element systems forming u-phases, silicon may act as an acceptor of electrons, thus stabilizing the u-phase at electron concentrations higher than

Jan 1, 1962

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By Stanley Herold

As an accompaniment to the interesting papers which discuss the practical aspects of forced drive, or flooding, in our oil fields, and to others which deal with laboratory or field tests on the same subject, a few remarks on the theoretical principles concerned may not be considered inappropriate at the present time. Without claiming to have had the field experience which some of you certainly possess I venture to present some of the results of an analytical investigation upon this method of increasing the recovery of oil from our natural reservoirs. I firmly believe that these results will accord with your experience. I shall confine the present discussion to the consideration of a perfectly ideal situation Let us assume that the productive formation lies perfectly horizontal, that it is of uniform thickness, of perfectly homogeneous texture, and that it contains oil with gas in solution, and no water, throughout a definite, although undefined, lateral extent. We shall furthermore assume that the pressure existing within the reservoir as thus specified, is such that some of the gas is in the free state, spread uniformly throughout, in the form of minute bubbles within the pores of the formation. We now have an ideal reservoir subject to the peculiar action of capillarity as described by the French physicist Jules Jamin. In all directions within the reservoir we see these bubbles of gas, separated by globules of oil which tend to remain in the capillary channels that connect the pores. The action of these bubbles and globules under the application or release of pressure has been fully described by Jamin.1 Most of our oil fields in the Mid-Continent and Eastern districts are subject to this action of capillarity: The fact that the actual reservoir is often far from being ideal in the manner specified above does not preclude the, influence of this phenomenon. The oil, existing under a pressure exerted by the compressed gas, is securely locked in place

Jan 11, 1926

By Werner Langguth

The modern process and plant for the precipitation of gold from chlorine solutions, by sulphurous acid gas and hydrogen sulphide, differ materially from the older methods of precipitating with sulphate of iron. The chemical process and its applicability, as carried out in the Golden Reward chlorination-works at Deadwood, S. D., was described and discussed in the Engineering and Mining Journal, of New York, for February 14, and March 21, 1891. I purpose to give, in this paper, the details of construction from a general standpoint—the particular arrangement, most suitable to each case, depending, of course, upon local conditions. The accompanying sketch shows the arrangement. The plant consists of a wooden, lead-lined tank, in which the chlorine solution is precipitated; apparatus for the production of the precipitants, sulphurous acid and hydrogen sulphide; and a pressure-tank and filter-press for the collection and filtration of the precipitated gold-sulphides. These parts and arrangements are, in general, those which I employed in the Deadwood chlorinationworks, and which have proved practically successful, more than $100,000 worth of gold having been already precipitated by this method. In the construction of the generator and pressure-tank I have made, however, a few slight changes. 1. The Precipitating-Tank. The exact dimensions of this tank are not of much importance. A horizontal area of 10 x 12 feet and a height of 12 feet, holding about 7000 gallons of solution, is a good size. As the amount of attention and care required to precipitate the solution in a precipitatingtank is independent of the size of the vessel, there is economy in tanks of large capacity. Square tanks are more advantageous than round ones, because they need less floor-space, and at the same time are cheaper in construction. These tanks are made of common 2inch pine boards and 12 x 12-inch timber. They are well-bolted,

Jan 1, 1893

By William L. Saunders

Many members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary&apos;s approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-coxpressors and machinery driven by compressed air, has no desire to injure its own business by claiming for this new machine that it should immediately supersede all existing applications of pneumatic transmission of power for drilling. On the

Jan 1, 1908

By T. C. Mendenhall

All persons, actively engaged in your profession, must have a natural interest in the subject of weights and measures. All members of the engineering profession have to do with operations of weighing and measuring—some with measuring more than weighing, and some with weighing more than measuring—but all with both of these processes to a greater or less degree. Methods of weighing and measuring have improved constantly from the earliest times and have kept pace with the advance of other technical processes. It is, therefore, believed that you will be interested in a few remarks concerning some of the more recent advances in relation to the establishment of decimal standards of length and mass in this country. Before speaking of this, I will refer very briefly to some facts which may not be very generally known regarding our customary system of weights and measures. Although the yard is universally accepted as the unit of length, and the pound as the unit of mass, it is not generally understood, I believe, just in what respect the yard is the unit of length, or the pound the unit of mass. That is to say, it is not generally known in what degree these units have been legalized by Acts of congress. Doubtless, many of you are familiar with the facts which I will briefly recapitulate. The Constitution of the United States authorizes Congress to establish a system of weights, measures and coinage. The establishment of a system of coinage, as you know, was one of the first acts of the government, and the system then adopted is certainly one of the most perfect, if not the most perfect, that the world has yet seen. But, although Congress had the power to establish a system of weights and measures, it has never yet seen fit to exercise this power; that is to say, Congress has never yet

Jan 1, 1890

By Robert W. Elayer

In August 1973, Fluor Utah, Inc. was awarded a contract by the Office of Coal Research (now part of the Energy Research and Development Administration), Department of the Interior, for the examination of the unique problems of large-scale surface coal mining to supply coal conversion complexes. The project consists of two phases: (I) data base development and organization and the formulation of a mathematical computer modeling system for surface mining; and (II) computer manipulation of the data base in accordance with the model to formulate several typical preliminary mine and preparation plant designs. Phase I is scheduled for completion by the end of July 1975 and Phase II is scheduled to be complete by the end of January 1977. This paper briefly discusses the effort for only one aspect of this project-the foundation for geologic modeling developed in Phase I. The Phase I task of geologic modeling can be broken down into two subtasks: (1) identify areas containing sufficient resources of surface-minable coal to support at least one large-scale mining complex, and (2) characterize the coal deposits in these areas for computer storage and retrieval. Identification of Resource Regions The basic production design criteria for large-scale surface mining, as stated in the contract, is the production of 75,000 tpd, or more, of bituminous coal. Based on a constant total Btu delivered to the preparation plant, daily production requirements for the different coals are as follows: Bituminous Coal 75,000 tons Subbituminous Coal 99,500 tons Lignite 143,500 tons Although surface mining on this scale is presently non-existent, it is deemed that future operations, in order to meet the increased energy demands, will have to look forward to much larger scale mining complexes. These tonnage requirements are meant to be used only for the delineation of general areas suitable for large-scale surface mining, termed "Strippable Coal Resource Regions." They were determined largely from the latest complete detailed coal resource estimates of the U.S. Bureau of Mines. Nine strippable coal resource regions, containing over 100 billion tons of strippable coal resources, were identified [(see Fig. 1)]. The delineation of these regions was based entirely upon estimates of surface-minable coal resources and the production design criteria for large-scale surface mining. If surface-mined coal was combined with underground production, or if smaller production rates were specified, then other areas which were omitted here would be included in the regions. Changing the outline of the regions, however, would not add any new mining situations to be studied in Phase II. Characterization of Coal Deposits The second subtask involved the general characterization of the coal deposits contained in the strippable coal resource regions. The geological information gathered

Jan 1, 1976

By W. R. Ingalls

I WAS led some time ago to draft a statement of economic principles immediately affecting our national welfare from the standpoint of the engineer. It was the intention to offer this to the American Engineering Council as a resolution to be adopted, or a declaration to be made, of course after suitable con-sideration and debate. The presentation has not been . formally made, but I have been asked to let it be made to the mining engineers through the medium of MINING AND METALLURGY, the American Institute of Mining and Metallurgical Engineers being a constituent part of the Federated American Engineering Societies. I shall welcome any expressions of opinion that this statement may inspire. The statement follows: The engineers of, the United States, functioning through the American Engineering Council of the, Federated American Engineering Societies, feel it their duty to advise the American people respecting the present state of economic affairs in the nation, just as an individual engineer would his client. The people of the United States constitute a great corpora-tion, whose business affairs are analogous to those of a commercial company -multiplied many times. The engineers feel constrained to offer their opinion owing to the responsibility to do things which rests upon them. Confronted by the steady impoverishment of natural resources and the operation of the economic law of diminishing returns it devolves upon management, functioning through the engineering profession aided by scientists, to make such improvements leading to increased production and such elimination of wastes as to offset the increasing adversities of nature merely to hold our own; and to do more than offset them in order to improve the scale of living of the people. The engineers accept this responsibility, but in so doing they demand attention to their advice respecting fundamental economic matters, lest they be unduly hampered in the performance of the professional duties, which they acknowledge. The American Engineering Council therefore declares the following as the advice of engineers to the American people:

Jan 8, 1923

By John F. Blandy

ALTHOUGH the question of the "waste of anthracite coal mining" has been so frequently discussed, and a committee was appointed at the first meeting of this Society to consider and report upon the subject, still but little progress seems to have been made in arriving at a conclusion as to how it can be reduced. That committee made a preliminary report at the August meeting, 1871, in which it divided the question into three parts, namely Waste in mining, in preparing for market, and in transportation. I shall not here refer to the first item, as so much depends upon the peculiar features of each separate mine, and the skill of those in charge; but in reference to the second, that of preparing the coal for market in breaker and screens, I wish to make some remarks. There is no use considering the question, whether the coal should be broken up to suit the fancy of consumers; all miners are satisfied that it should not be, but the consumers decide that they want it that way, and the miner must submit, and simply utter his maledictions upon the head of the man who first suggested a breaker or screen, if that is any consolation to him. What is called waste in this process of preparation, is the dust and fine coal, which results from the breaking and screening, and, as we all know, this is a very important percentage of what passes from the slope to the top of the breaker. Now, if this dust and fine coal can be utilized-the slate which is&apos; picked out is not to be taken into consideration as waste-then we get rid of this item entirely. There is no question in my mind that this article can and will be used as a steam generator at least, and I think, therefore, that in depositing

Jan 1, 1877

By B. Prof. Silliman

THE experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones&apos;s Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phoenixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 212° F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so con¬structed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care- * See paper by Dr. Hunt, page 325.

Jan 1, 1876

There was such a large demand for copies of the speech of Herbert Hoover at the A. I. M. E. dinner given in his honor on Sept. 16, that a special edition has been run off; anyone desiring copies may obtain them by applying at the office of the Secretary.

Jan 12, 1919

By J. E. Johnson

Discussion of the paper of Mark A. Amnion, presented at the Cleveland meeting October, 1913, and printed in Bulletin No. 70, October, 1913, pp. 1167 to 1 79. J. E. JOHNSON, JR., Ashland, Wis.:-Mr. Amnion&apos;s paper is of great value and it is not with any desire to reflect. on it that I wish to make some comments on the use of the scleroscope. We obtained one on trial some months ago and made very extensive tests with it, but without getting very satisfactory results. The readings on good car-wheels and bad ones were just about the same, but the factor in its use most likely to produce erroneous results is a variation in the thickness of the specimen being tested. In order to find out something on this subject we cut a thin disk, about -1,: in. thick, off a brass rod; then one 0.25 in. thick, and another about 1 in. thick, put the surfaces of all in about the same condition and tested them with the scleroscope. The readings varied widely; the resilience of the anvil evidently entered to a very high degree on thin pieces. By putting a soft cushion between such a thin specimen and the anvil, and forcing it up against the tube, the softness of the cushion cut off the resilience of the anvil and the results were more like those of the thick specimens. After a thickness of 1 in. was passed, the specimen seemed to have mass enough so that the resilience of the anvil no longer played an important part, and above that thickness results on different materials would be comparable, even though the thicknesses differed. But in order to get comparable results on thin specimens the thickness of those being tested should be the same. I should like to ask how the variations introduced in this way were overcome, so as to get strictly comparable results. Mr. AMMON :-.I have not had much experience in that, but the scleroscope is simply an indication of the surface harden-

Dec 1, 1912