Search Documents

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947

By W. T. Lundy

THE forms in which sulphur is commonly found-native sulphur, sulphides of many metals and sulphates-are widely distributed throughout the world. The two first mentioned are the principal sources of sulphur. Substantial amounts of sulphur in some form are recovered from gases from industrial plants and from gases from smelters treating other minerals. In recent years, plants have been installed in the United States to recover sulphur in elemental form from sour gases."' The amount of sulphur so produced is small at the present time but undoubtedly will increase in the future. The recovery of sulphur from gases is not covered in this chapter, which is confined to: (1) native sulphur deposits of Texas and Louisiana; (2) those of Italy; (3) other scattered deposits of native sulphur; and (4) pyrites deposits found in many countries of the world.30 Sulphur, a nonmetallic element, occurs normally in well developed bipyramidal or tabular crystals of the orthorhombic system, as well as in stalactitic and earthy masses. The mineral has a distinctive yellow color, which may be dark and discolored by impurities; the streak is white; the luster is resinous; and the fracture is conchoidal to uneven. Sulphur is translucent to opaque; has a hardness of 1.5 to 2.5, a specific gravity of 2.05, and an atomic weight of 32.06.16 The molecular weight of the solid is expressed by the symbol SS and that of the liquid and vapor ranges from S2 to S8, depending on the temperature. Sulphur melts at a temperature between 2340 and 248°F, depending on its crystalline state, to a liquid of dark amber color, the boiling point of which is 832°F. The viscosity near the melting point is about that of water and increases to 50,000 times that of water at a temperature of 380°F, subsequently falling rapidly to a low figure at the boiling point. Crystallization changes slowly from rhombic to monoclinic above 205 °F and in cooling the transformation is reversed. The mineral is a very poor conductor of heat and electricity; it is insoluble in water and nearly all acids and is soluble in cold carbon bisulphide and carbon tetrachloride. It ignites in air at a temperature of 478°F, burning with a distinctive blue flame with evolution of sulphur dioxide.47

Jan 1, 1949

By R. M. Bird

Few persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry-sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co. A few years ago the so-called Albany sands were dug by simple methods and hauled by horsecart to railroad. Depletion of sand near railroad sidings and extended use of automotive power have appreciably extended the area from which sand is now being dug. It is not unusual to haul 5 miles to the railroad. As stripping is quite shallow, 6 to 18 in., and the banks of usable sand generally run from 12 in. to 4 ft., it is economical to work the bank by benches so narrow that the overburden can be thrown by hand shovel to the exposed bottoms. In effect the top soil goes back to where it was, but on a lower level. Consequently the general surface appearance of a mined acreage is the same as before. This condition is in fact cutomarily required when a farm owner sells his sand in the ground. After such replacement, in the course of 3 to 5 years the soil is no less fertile than it was before mining. The sand itself varies as to grain and bond vertically and also along the breast. No mechanical equipment has been developed to compete with hand shovels and no machine has as yet been devised that grades the sand as required. Uniformity of sand, as shipped, depends first, last and all the time on the man on the job. Mixing equipment can change the appearance of the sand and mask its lack of uniformity, but it will never correct wrongly graded sand, dug from the bank. Modern methods of testing are helpful in setting up standards against which the man in the bank can compare his sands, but a good bank foreman is the only assurance that the sand, as dug, matches the required sample.

Jan 1, 1926

By Paul Queneau

FROM the first days on the Norman beaches to the last days on the Elbe the Army Engineers of World War II lived off the countryside for the great bulk of the construction supplies needed for the fulfillment of their ultimate mission-to keep the army moving. To accomplish this end, vast tonnages of rock, timber, and steel were required in the construction of roads, railroads, and bridges. Combat Engineer battalions operated quarries under shell fire as a routine matter. An Engineer forestry company was decimated while cutting bridge timber on the Siegfried line. Oneof the more spectacular feats of the Army Engineers in obtaining construction materials was the operation of the Hadir Steel Works during the fall and winter o f 1944.

Jan 1, 1946

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

By WALTON H. HAMILTON

THE demand for "production control" has, like the poor, been with us always. With the development of the nation, the accumulation of business experience, and a maturing understanding of how our many and varied industries work, it is increasingly evident that an uncontrolled output is a source of great mischief and that order and performance demand a control of production. To see clearly the demand for "production control" we must look in detail at the ways in which industries operate. General pictures, grand aggregates, situations as "wholes," and smoothed curves are likely to be deceptive. An industry may seem to keep the even tenor of its ways, and yet the establishments which made it up may experience a great range of fortunes. A nice bundle of statistics may show in the aggregate a lovely regularity which is not shared by the firms which make up a trade. An industry may appear to be reasonably profitable, and yet the profits may be very unevenly distributed. The people in an industry, and dependent on it, are managers, laborers, stockholders, creatures of flesh and blood, such as you and I. General pictures and abstract statements must not blind us to what is happening to firms, corporations and individuals.

Jan 1, 1929

By J. Kent Smith

The object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent; furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575" F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450" F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450" F.) were reheated for varying periods of time at 575" F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By A. G. McGregor

During the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and equipment developed. Some of these features are described in this paper. Concentrate Hauling, Unloading and Sampling System (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences. A concentrate unloading pocket (Fig. 4), 180 ft.long, is provided at the smelting plant, which has a conveyor belt running throughout its length underneath the track. To unload a car, the vertical plug at the end of the car is lifted by means of a chain hoist which is supported by a trolley overhead. The gate at the end of the car is opened approximately 18 in. The removal of the plug leaves a hole down through the concentrates. The concentrates are poked through the hole from the top of the car until it is convenient for a man to stand on the bottom and draw one of the slats in the bottom toward the gate end of the car. The concentrates are then raked down with hoes on their natural angle of repose,

Jan 1, 1917

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By G. Howell Clevenger, Bhupendranath Ray

Formerly great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,l Breuil,2 Wigham,3 Burgess and Aston: Ball and Wingham,5 Miiller; Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil9 and Stead.10 Stead11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence 'of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness" to the presence of small amounts of copper. Turner12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 1, 1914

By W. C. T. Yeh, T. G. Oakwood, A. A. Hendrickson, R. H. Hammar

The objective of the research is to determine whether solid-solution strengthening effects observed in dilute solutions of silver can be accounted for by the influence of the solute addition on the dislocation structure oj- the crystals. The additions of both tin and indium produced only small changes in the dislocation densities and arrangements in silver crystals. However, as found previously, small solute additions have large effects on the tensile properties; the inj-luence of the tin and indium additions on the temperature dependence of the flow stress and the easy-glide range is especially strong; It is concluded that the indirect strengthening effect of the solute due to variations in the dislocation density as proposed by Seeger is of minor importance and that solute atom-dislocation interactions are responsible for the observed strengthenirzg effects. The experimental results were combined with those of Rogausch to test the concenlvatiorz dependence of solute strengthening. Both the first and one-half power dependences of the critical resoleed shear stress on concentratiorz fail in very dilute solutions. THE objective of the research is to determine whether solid-solution strengthening effects observed in dilute solutions of silver can be accounted for, at least in part, by the influence of the solute addition on the dislocation structure of the crystals. It is recognized that the addition of solute atoms may influence the strength properties of a metal through both "direct" and "indirect" effects. The former refer to the strengthening mechanisms that result from the interaction of solute atoms with dislocations; in the latter case, the strengthening effects arise as a result of solute's influence on quantities such as dislocation density, dislocation arrangement, stacking-fault energy, diffusivities, the elastic constants, and so forth. It is clear that the correct interpretation of solid-solution strengthening phenomena cannot be given until the importance of indirect strengthening effects is properly evaluated. In the particular case of close-packed metal crystals, Seeger showed that solute strengthening effects in dilute solutions of copper and silver might be accounted for by an increase in dislocation density due to the addition of the solute. Seeger's argument was that the strengthening effects extrapolated from more concentrated solutions indicate that small concentrations of impurities raise the critical resolved shear stress much more than is predicted by a concentration-independent dislocation density. The above idea was a very reasonable one. The dislocation theories of work hardening of Taylor,2 Cot-trell, 3 Mott, 4 and seeger5 had already associated the increased flow stresses with increased dislocation densities in deformed metals; investigations of the dislocation structure of metal crystals had provided a logical basis for expecting an increased dislocation density in crystals containing impurities (see for example, Ref. 6). The numbers involved seem reasonable, too. It can be expected that the flow stress of the crystal would increase as the one-half power of the dislocation density.' Solute additions of 1 at. pct to metal crystals result in strength increases by factors in the range of three to ten. If one assumes that the strengths of the pure metal crystals are determined by their dislocation densities, then dislocation-density increases of one to two orders of magnitude as a result of solute addition would be required to account for the observed strengthening—not an unreasonable expectation. In addition to the effect of the solute addition on dislocation density, one might also anticipate important strengthening contributions to result from the solute's influence on the dislocation arrangement. Parker and washburns have reviewed a number of experimental evidences which show important strengthening effects due to the presence of subboundaries. Further, lattice strains due to impurity segregation would be expected to influence the distribution as well as the dislocation density of the as-grown crystal. As pointed out in the reviews of Chalmers,6 Elbaum,9 and winegard,lo micro segregation of impurities occurs at all interfaces of crystals in cellular growth; the impurity gradient results in lattice strains which can be reduced with the presence of dislocation arrays in the region of the impurity gradient. Hence, one would expect the presence of a solute to favor the formation of dislocation subgrain structures and that the subgrains would have an important influence on the strength of the crystal. The experimental observations that concern the possibility of an important strengthening contribution through the influence of the solute on the dislocation density or arrangement are not in agreement. Haasen has reviewed the observations of Meakin and Wils-dorf,12 Howie,13 and Bocek 36 and concluded that the solute's influence on dislocation density is not sufficient to account for strengthening effects in concentrated solutions but might, as seegerl suggested, make an important contribution in very dilute solutions. On the other hand, Hendrickson and Fine 14 concluded that changes in the dislocation density and dislocation width accounted for the solid-solution strengthening effects observed in silver-based aluminum solid solutions. Goss et a 1.I5 observed dislocation arrays in Ge-6 at. pct Si, Ge-0.2 at. pct Sn, and Ge-0.2 at. pct B crystals that were not observed in germanium crystals of

Jan 1, 1968

By Maurice Cook

A procedure of obtaining specimens of lead, tin, and cadmium with a moderately equiaxed structure and a smooth surface suitable for etching without grinding and polishing is described; the advantages of general oblique illumination (as opposed to vertical illumination) in the photomicrography of pure metals .are stated. Using these methods, a statistical study of the changes brought about in deformed lead, on annealing, has been made. The common mode of structural change was found to be recrystallization. Cases of growth of one original grain into another were rare; but if a totally recrystallized specimen was annealed above 200° C., a few large grains appeared and spread over the whole area, except for a certain number of small grains which remain unabsorbed. The temperature needed to produce structural change in lead was found to be lower, the greater the degree of deformation. With tin, an extension of 28 per cent. caused practically no recrystallization at ordinary temperatures, but recrystallization occurred if the specimen was heated to 100° C. In cadmium at low temperatures, the grain size decreased in marked manner as the deformation increased; but at high annealing temperatures, the grain size was comparatively independent of the degree of deformation. THE structural changes in metals brought about by annealing following a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum,1 tungsten,2 iron,3 copper,4 gold,5

Jan 11, 1924

By H. Ries, R. E. Somers

Bodies of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tintol and Rammels-berg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no. doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany;4 Ducktown, Tenn.;5 southwestern Virginia;=

Jan 1, 1918

By E. W. Johnson, M. L. Hill

Equilibrium concentrations of hydrogen in iron were measured at H2 pressures up to 136 atm and temperatures down to 145°C. Residual hydrogen was prominent near 600°C in air-melted but not in vacuum-melted iron. The diffusible hydrogen solubility is abnormally high below 390°C, confirming the hypothesis of hydrogen trapping.' It appears that the traps for hydrogen in iron form suddenly on cooling. The estimated H2 pressure in equilibrium with 5 ppm hydrogen in steel at room temperature is less than 1000 atm. It was shown previously1 that the diffusivity of hydrogen in a-Fe below 200°C is anomalously low, a behavior attributed to the presence in the metal structure of hydrogen "traps." The energy of the trapped hydrogen was computed as 4.8 kcal Per g-atom below that of the interstitially dissolved hydrogen. The strongest confirmation of the trap hypothesis should be obtainable from measurements of the hydrogen solubility at low temperatures. such measurements have been performed and are reported in this paper. The "residual hydrogen" effect1'' must be carefully controlled if valid measurements of the solubility are to be obtained, and such an effort was made in the present work. Previous data for the solubility of hydrogen in iron have been summarized by Geller and Sun.3 Their equation for the most probable solubility at 1 atm in a-Fe above 400°C is

Jan 1, 1962

By E. C. Bain

THE more familiar compositions of iron-carbon-chromium1 and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallographic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By William H. Kobbé

The word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone. upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. 11. DRILLING Determining Factors in Selection of Method The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well. 1. Character of the Formations Overlying the Reservoir The strata overlying the reservoir may consist of beds of shales, clays, sands and other soft materials, or they may be slates, limestones and sandstones consolidated to all degrees of hardness. Very often the overlying strata are predominantly of soft materials but interbedded with harder formations. Likewise, soft strata are encountered at different horizons in an overburden consisting almost entirely of the harder sedimentaries. The physical character of this overburden is frequently

Jan 1, 1917

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By W. G. Matteson

THE origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete information revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill' advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,2 using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no. evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of, the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the, subsequent

Jan 2, 1921

By Leo Tarasov

MAGNETIC torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade1,2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time 1.5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction, or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements.

Jan 1, 1939

By E. N. Doyle

Since the mid-1930's a number of plants, using the principles of heavy media separation, have been installed throughout the world. In cases involving lead, zinc or lead-zinc ores the reasons for the choice of this type of beneficiation process have fallen into four major categories: A) The economic recovery of additional distinctly separate products, such as dolomite limestone at the Mascot Plant (1) of the American Zinc Co., and the ferrosilicon produced by St. Joseph Lead Company. (2) B) The elimination of a large portion of run-of-the-mine ore prior to grinding and flotation, to allow increased throughput with low capital cost. Examples of this approach are the Levante and Ponente plants of the Montevecchio Company in Italy (3) and the frequent choice of the Sink-Float process by the Penarroya Company of Paris. C) The processing of a sedimentary deposit, in which the valuable mineral is contained in the matrix separating the boulders, as was the case at the St. Joseph Lead Company plant at Haydon Creek (4) and also at Bunker Hill Mining and Smelting, Kellogg, Idaho. D) The simplification of Around support programs in mines by allowing greater freedom of action in the extractive pattern. An example of this choice is Cominco’s Sullivan plant which came into being as part of an extensive proposal to update the mining, crushing, transportation, grinding and beneficiation processes. (5)

Jan 1, 1970