Search Documents

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By D. M. Blacknall, N. N. Winogradoff, E. W. Williams

Low-temperature measurements of photolumines-cence were used to evaluate the progvess in materials development. Variation of the impurity type, impurity concentration, and method of growth were used to clarify the chemical origin of defects in GaAs. Melt-g~ozun, epitaxial vapor-, and solution-grown samples were studied. A comparison of measurements at 77" and 20°K shows that more defects can be observed at the lower temperature. Th'vee residual defects were identified in relatively pure GaAs. These were: silicon, copper, and a gallium vacancy-donor complex. Solution growth from a gallium solution inhibits the formation of the latter two. Eleven defects were studied and the "optical" activation energy of some of these, namely, silicon, cobalt, and chromium, has not been reported in the literature before. THE discovery of the injection laser in 1962 prompted extensive measurements of the photoluminescence of GaAs. The measurements were made at 77°K on GaAs doped with shallow impurities at various doping levels and compared with electroluminescence1'2 and absorp- tion data.374 In addition, lower-temperature studies were made on relatively pure GaAS' and on GaAs doped with oxygen,5'" manganese,' and copper.' The observation of defects* in GaAs with photolu- *The word "defects" ~efers to both chemical impurities and native defects. minescence at low temperatures makes photolu mines-cence an invaluable tool in evaluating the progress in materials development. The only previous evaluation was done at 77°K when solution-grown and melt-grown GaAs were compared.O No identification of defects was made but it was shown that some of the deep-level luminescence seen in melt-grown GaAs was absent in solution-grown GaAs. The present work extends the comparison of preparation techniques to lower temperatures and to a study of epitaxial vapor-grown GaAs. It is particularly valuable for thin epitaxial layers since they cannot be analyzed by conventional analytical techniques. In addition, by varying the impurity type and impurity concentration the chemical origin and nature of defects in GaAs was demonstrated. Eleven defects were studied in all. Three of the defects were identified as residual defects which often contaminate GaAs prepared from the melt and the vapor. Only one such defect was observed in GaAs grown from a gallium solution and this was identified as silicon.

Jan 1, 1968

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I- 18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By L. W. WALLACE

IN an engineering fashion we have made an assay of the engineering profession, using as a. sample the engineers listed in "Who's Who in America" (1928-1929). We are aware that some will say it is an unfair sample; that it came from the best mine. This is readily admitted, with this qualification: that all engineers and architects by virtue of their training and experience have been freed of most of the dross to which mankind is heir. They are -a selected group to begin with, having all the potentialities those in the sample possess. We are also aware that some will say a part of those included in the sample are not engineers. Our answer to that criticism is this: An engineer is no less an engineer because for the time being he is president of a bank, a university, an opera company, or a hotel company. Moreover, he is no less an engineer because he is a governor of a commonwealth, a United States senator, a member of the Cabinet, or the President of the United States.

Jan 1, 1929

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By L. F. Terry, H. K. Ihrig, D. J. Sabin, Ralph E. Davis

This paper presents the results of a study of the comparative values of the several fuels commonly used by industrial plants. It shows that the energy actually recovered from any fuel and turned into useful work is dependent upon several factors: (1) the total energy available in the fuel, (2) energy losses resulting from combustion reactions and (3) energy losses dependent upon the mechanics of the firing operation. The chemistry of combustion and the losses resulting therefrom are discussed. The Advantages and disadvantages of the several mechanical methods of firing and the resulting heat losses in each are developed. Data obtained from several typical fuel operations, where careful records have been maintained, are presented to show that the practical results in the actual operation are in harmony with the theoretical results developed in the earlier part of this paper. Water power and solid, liquid or gaseous fuels are at present the only commercial sources of energy. The economic utilization of any one of them depends, in the final analysis, on the cost of energy per unit of finished product to which the energy is applied. The location of the plant utilizing the particular fuel chosen is a large factor in the original choice. The cost per unit at its original natural source, or even in its delivered form, is not always the final measure of its worth. The use of electricity as a source of energy illustrates this to the extreme. Electric current produced from water power is very cheap in certain localities. In Norway, current is sold as low as ½0# per kw-hr., while in dry cells it costs as much as $10 per kw-hr. Yet the sale of dry cells is a large business. The selling price of gas also varies widely. In some localities natural gas for the manufacture of carbon black sells for as low as $0.02 per million British thermal units, while artificial gas for domestic purposes sells for as high as $6 per million B.t.u. Obviously the cost per unit of energy is not the final determining factor in its purchase. Any discussion of the economic utilization of fuels must include costs in relation to the units of finished material manufactured. In large central power generating stations, this is the over-all cost per kilowatt-hour, and in ceramic firing the cost per unit of finished product of a certain quality is the criterion of economic utilization.

Jan 1, 1931

By Jasper L. Stuckey

It is not known when kaolin mining was first begun in North carolina, Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some Of the early English porcelains. In 1744,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply Of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage Of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. 'Or some 20 years, kaolin mining was carried On chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 Yea's most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. Distribution The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Ire-dell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. Geology With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1948

By Jasper L. Stuckey

It is not known when kaolin mining was first begun in North carolina, Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some Of the early English porcelains. In 1744,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply Of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage Of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. 'Or some 20 years, kaolin mining was carried On chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 Yea's most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. Distribution The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Ire-dell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. Geology With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1948

By AIME AIME

MONDAY, Feb. 21, evokes memories of the Silver Corridor at the Waldorf to be recalled and reflected upon for time to come when thoughts drift to the Annual Meeting of 1944. Crowded though it was, on occasion there lurked in the mind's eye a vision of what might have been had the 2886 persons who put in an appearance at one time or another milled around in the lobby of 29 West 39th Street. Some confusion resulted from difficulty in locating meeting rooms, but for the most part everyone found what he wanted. The usual bulletin board of members registered was missing this year and rumor has it that tile Waldorf didn't approve. Registration broke all previous records with many a busy engineer realizing that the program had something to offer that would be of use in his particular job. It might be noted here that "Arpad" co-operated nicely, previewing spring days on Monday, Wednesday, and Thursday; Tuesday was a bit damp.

Jan 1, 1944

By Jasper L. Stuckey

HISTORY IT is not known when kaolin mining was first begun in North Carolina. Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. Some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some of the early English porcelains. In 1944,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. For some 20 years, kaolin mining was carried on chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 years most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. DISTRIBUTION The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Iredell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. GEOLOGY With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1947

By G. R. Belton, R. J. Fruehan

The Knudsen cell-mass spectrometer combimtion has been used to study the Fe-Al and Ag-Al liquid alloys. By application of the recently developed integration technique to the measured ion-current ratios, activities have been derived for the Fe-A1 system at 1600° C and for the Ag-Al system at 1340"C. The results are partially represented by the following equations: Internal consistency between the data on silver-rich and iron-rich alloys is demonstrated by application of the literature measurements on the distribution of aluminum between the nearly immiscible liquids iron and silver. The usual restrictions on the ratio of the mean free path of the escaping atoms to the orifice diameter of the Knudsen cell are shown not to be limiting in this technique. DESPITE the importance of a knowledge of the activity of aluminum in understanding deoxidation equilibria in molten steel, no direct studies have been made of activities in liquid Fe-A1 alloys at steel-making temperatures. Lower-temperature direct studies have, however, been carried out on aluminum-rich liquid alloys by Gross, Levi, Dewing, and Eilson' at 1300°C and by Coskun and Elliott' at 1315°C. Apart from phase diagram calculations by Pehlke, other determinations have been indirect and were made by measurement of the distribution of aluminum between iron and silver475 and combination of these data with extrapolated activities in the Ag-A1 system.~-% ecently, however, Woolley and Elliott have made a significant contribution by directly measuring heats of solution in the Fe-A1 system at 1600°C. The present authorslo have recently employed a Knudsen cell-mass spectrometer technique in a study of activities in iron-based liquid alloys. In this technique activities and heats of solution are determined from a series of measurements of the ratio of ion currents of the components; and since ion-current ratios are used, problems caused by changes in instrument sensitivity or cell geometry are overcome. Results obtained for the Fe-Ni system were found to be in excellent agreement with previous work, thus demonstrating the reliability of the method. The present paper describes a similar study of activities in the liquid Fe-A1 and Ag-A1 systems, this latter system being included in order that a meaningful comparison can be made with the above-mentioned indirect studies. INTEGRATION EQUATIONS A detailed derivation of the equations used to determine the thermodynamic properties from the measured ion current ratios has been given elsewhere;'' however it is useful to summarize them here. By the combination of the Gibbs-Duhem equation with the direct proportionality between ion-current ratios and partial pressure ratios, it was shown that for a binary system at constant temperature and pressure: where al is the activity of component 1 with pure substance as the standard state, N, is the atom fraction of component 2 in the solution, and I; and t'2 are ion currents of given isotopes of the components. The activity coefficient is given by: this latter equation being more suitable for graphical integration. Combination of Eq. [l] with the Gibbs-Helmholtz equation gives an expression for the partial molar heat of mixing: EXPERIMENTAL A Bendix Time-of-Flight mass spectrometer model 12! fitted with a 107 ion source and a M-105-G-6 electron multiplier, was used to analyze the vapor effusing from the Knudsen cell. The arrangement of the Knudsen cell assembly was essentially that of the commercial instrument (Bendix model 1030) but with several modifications. Instead of heating with a single tungsten filament, a cylindrical tantalum-mesh heater was employed. Up to 1400°C simple resistance heating was used but above this temperature electron bombardment between the tantalum mesh and the tantalum cell susceptor was necessary. The temperature was measured by means of a Leeds and Northrup disappear ing-filament type optical pyrometer sighted on an essentially black-body hole in the side of the cell. Details of the temperature control, temperature measurement, and in situ calibration of the optical pyrometer can be found elsewhere.I0 In the investigation of the Fe-A1 system the Knudsen cells were constructed of thoria crucibles with fitted thoria lids (Zircoa). The cells employed in investigating the Ag-A1 alloys were made up of high-purity alumina crucibles (Morganite) with lids of recrystal-lized alumina (Lucalox). The cells were 0.370 in.

Jan 1, 1970

By Michael Shaughnessy, O&apos

The outstanding features of the Coloinbian situation for the year 1929 were legal and political. The passage of Law 84 and the promulgation of the Regulatory Decree 150 were recounted in the review for 1928, as was also the Presidential proclamation suspending this law and its accompanying decree until decision could be reached in the suits filed against them before the Supreme Court and the Council of State. Early this year the Minister of Industries, Jose Antonio Montalvo, announced the appointment of a commission of foreign experts to aid in drafting a new petroleum law. He requested all of the foreign experts employed not to consult with the oil company representatives in Bogota, and these experts were therefore shut off from receiving any suggestions from those who had actually operated in the country and knew the conditions under which operations would take place. It was to be expected that the provisions of a law suggested under such circumstances would not meet operating conditions satisfactorily. The specific objections are stated in O'Shaughnessy's South American Oil Reports (April, 1929). An especially qualified commentator observes that one of the curious provisions of the proposed law was the high royalty on gas—5c. per 1000 cu. ft. of gas produced. There was also a provision requiring 20 per cent. of the stock of the company operating in Colombia to be offered for sale to Colombians. The bill failed to pass Congress in the closing hours of the session. The Supreme Court, in the meantime, handed down its decision on Law 84 of the previous year and Regulation 150 covering the enforcement of that law. Contrary to expectation, the majority opinion of the Court practically affirmed the constitutionality of both the law and the regulatory decree, with the exception of Article 20 and parts of Article 21 of the decree which referred specifically to the registration of private properties. At the time the suit was filed against Law 84 and Decree 150 the operation of these measures was suspended by the Executive. Law 84 and its Regulatory Decree 150 still remain suspended as the Council of State has not yet brought in a decision upon the questions raised in the suits instituted by the various companies against the law and decree, and at the moment of this writing it appears unlikely that such a decision will be reached by that body.

Jan 1, 1930

By J. S. Westwater

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W, within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleve-land-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. Al1en.† Mather " A " shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather "B," also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation. Shaft Sinking General Plan An average depth of 16 ft of sand overburden at the shaft site was cleared away by bulldozer, and the shaft approximately 15 by 20 ft in rock opening put down to an initial depth of 87 ft. Mucking of the broken rock to this depth was accomplished by an Insley excavator equipped with a 1/2 yard ca-pacity Owens clamshell bucket. Addition of 200 lb weight to each lip of the clam bucket provided adequate "bite" to dig the broken diorite and jasper rock. Temporary heavy wood bearers were placed across the shaft mouth to support the steel shaft sets which were hung in this initial 87 ft depth, aligned accurately and concreted in place from the lowest set upwards. The permanent steel headframe foundations and three service tunnel openings to the shaft were also concreted in the upper section to the shaft collar. A temporary wood headframe was then erected over the shaft mouth, and initial hoisting machinery assembled consisting of a Lake Shore 12 ft diam single drum grooved for a 1 3/8 in. rope and powered by two 400 hp motors to attain hoisting speed of 1100 fpm. Compressed air was obtained from a Nordberg 2 stage tandem horizontal type with a capacity of 1500 cfm. An enclosed landing platform at the shaft collar was equipped with a rotary dump and pocket for discharge of the rock into a Euclid 15 ton truck. On completing assembly of this equipment and installation of a special cage in the shaft, sinking was resumed on a three shift, six days per week

Jan 1, 1950

By T. A. Rickard

T HE life and career of Daniel Cowan Jackling constitute a distinctive part of a passing era, marked by the intensive exploration and exploitation of the mineral resources of the western regions of the United States. In the development of his abilities and in the use of his opportunities, he typifies the initiative, the energy, and the skill of a modern captain .of industry. Daniel C. Jackling was born at Hudson, Mo., on Aug. 1.4, 1869. He was the only child of Daniel Jackling, born in England of English parents, and Lydia Jane (Dunn) Jackling, born in the United States, but of Scottish ancestry. His father died a few months after he was born, and he lost his mother less than two years later. The orphan boy was adopted by his aunt. He went to school as soon as he was old enough to walk the two miles, and back, alone. As opportunity offered, he went

Jan 1, 1937

By M. J. Stewart, F. Weinberg

PREVIOUS investigations into convective flow in molten metals have examined systems in which the length-to-height ratio of the enclosure is large, usually using long graphite boats.''2 In normal castings this ratio is generally small and it is not possible to extrapolate the results of previous work to casting configurations. The present investigation was undertaken to examine liquid flow in systems of low length to height ratio. The apparatus used for the experiments is shown in Fig. 1. The molten zone of tin is contained in an aluminum mold of inside dimensions 6.4 by 6.4 by 0.31 cm. A heating block containing a resistance coil is attached to one end of the mold and a cooling block is attached to the other end. These are used to produce a wide range of temperature differences across the mold. The mold is contained in a stainless steel tank which is heated from the outside by resistance heaters to give the required operating temperature during the experiment. Temperature measurements in the molten tin are made with an iron-constantan thermocouple PT equal to 5 atm. The phase diagram derived by us was the same as that found by Krivsky and Schuhmann, except for a similar discrepancy in one boundary line representing the gas composition in equilibrium with SO a. The vapor pressures of the pure components can be neglected at 1700°K, 1 atm and 2500°K, 5 atm. There-fore, in these cases PT is essentially the total pres-sure in the system. This is valid for all the diagrams presented by Krivsky and Schuhmann except for the one at 2500°K and 0.01 atm, where the vapor pressure of silicon is comparable to PT.6 This work was supported in part by the American Iron and Steel Institute. 'C. E. Wicks and F. E. Block: Thermodynamic Properties of 65 Elements, U S. Bur Mines, Bull. No. 605, 1963. R. P. Elliott: Constitution of Binary Alloys, 1st supplementary, McGraw-Hill Book Co., New York, 1965. 3W. A. Krivsky and R. Schuhmann, Jr.: Trans. TMS-AIME, 1961, vol. 221, pp. 898-904. 4M. F. Ancey-Moret, M. Olette, and F. D. Richardson: Mem. Sci. Rev. Met., 1964, vol. 61, pp. 169-76. 5J . F. Elliott and M. Gleiser: Thermochemistry for Steelmaking, vol. 1. Addison-Wesley, Reading, Mass. 1960. 6 J.Drowart, G. De Maria, and M. G. Ingraham: J. Chem. Phys., 1958, vol. 29, p. 1015. probe of 0.4 mm diam inserted into the open top of the mold. Radioactive sn113, in the form of a small sphere, was gently lowered into the molten tin at point A in Fig. 1 THERMOCOUPLE> WATER ARGON END HEATER QUENCH ARGON Fig. 1—Apparatus for detecting liquid flow. Point A indicates position the tracer was introduced.

Jan 1, 1970

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By J. W. Spretnak, G. W. Powell, J. H. Bucher

Tlze room-temperature tensile fracture oj smooth, round specitnens of three ultrnhigh- strength steels tempered to a wide range of strength levels was studied by means by light and electron-microscopic examination of the fracture surfaces. The fracture of AISI 4340 and 300 M at all the strength levels studied, and H-11, except after tempering at 1200° and 1300°F, occurs in three stages. The initiation of fracture is internal (except in some lightly tcmpeved specimers in which fracture is initiated at surface flaws), and is nucleated largely by separation at metal-second phase intevjaces. TIze voids grow and, coalesce to form a crack. When the crack has reached a sufficienl size, rapid propngutio~z ensues. Failure in this stage of fracture usually occurs by dimpled rupture of inicroshear stefis. In the case of H-11 tempered in the 1125° to 1300°F range, fracture in the shear steps is predominantly by concentrated deformation without void formation. The termination of fracture is usually occomplished by the formation of a shear lib in which fracture occurs by shear dimpled rupture. In the case of H-11 tempered at 1200° and 1300°F, no shear lip was obserued, and the radial elelments extend to the surface—a true termination slage does not exist. ThE tensile fracture of several metals and alloys has been investigated.2-4 In the case of polycrystal-line materials, cup-cone fracture usually results. The mechanism of cup-cone fracture may be summarized as follows.5 Cavities are formed in the necked region of the specimen. They usually are initiated by inclusions or second-phase particles. The cavities extend outwards by means of internal necking, and a crack lying about perpendicular to the length of the specimen is formed in the necked region. Subsequent crack growth occurs by the spread of bands of concentrated plastic deformation inclined at an angle of 30 to 40 deg to the tensile axis. Cavities are formed in the bands of concentrated deformation. The deformation bands zigzag across the bar with the net result that mac-roscopically the crack extends about perpendicular to the specimen axis. The final separation, or cone formation, appears to occur by continued crack propagation along one of the deformation bands out to the surface of the specimen. The micromechanics of the tensile fracture of ultrahigh-strength steels have not been thoroughly investigated. Larson and carr6,7 studied the tensile-fracture surfaces of AISI 4340 with a low-power microscope and reported that three stages of fracture could be observed in general. A centrally located region characterized by circumferential ridges, an annular region characterized by radial surface striations, and a peripheral shear lip were found. It was first pointed out by 1rwin8 that the central region is very probably one of fracture initiation and slow growth, and that the annular, radially striated region is one of rapid crack growth. Presumably the crack grows slowly, assuming roughly a lenticular shape, until it is large enough for the initiation of rapid propagation. In this investigation, it was attempted to determine the fine-scale aspects of the room-temperature tensile fracture of some ultrahigh-strength steels, and to relate the variation in fracture mode with microstructure. The steels studied were AISI 4340, 300M, and H-11 tempered to a wide range of strength levels. I) EXPERIMENTAL PROCEDURE The compositions of the steels studied are given in Table I. The steel was received in the form of hot-rolled bar stock 5/8 to 1 in. in diameter from which oversized specimens were machined and heat-treated. The heat treatments employed are given in Table 11. Subsequent to heat treatment, the specimens were ground to the final dimensions and stress-relieved by heating for 1 hr at 350°F (with the exception of the as-quenched steel). Standard smooth round specimens of 0.252-in. diameter and 1-in. gage length were tested in a Tinius Olsen Universal Testing Machine using a cross-head speed of 0.025 in. per min. The relatively coarse aspects of the fracture topography were determined by light-microscopic examination of sections through the fracture surface of nickel-plated specimens. A direct carbon-replication technique9 was used in the electron-microscopic study of the fracture surfaces. The replicas were examined in the electron microscope, and stereo pairs of electron micrographs were taken. The stereo pairs were then examined using a Wild ST4 Mirror Stereoscope. Carbide and inclusion particles extracted in the replicas were analyzed by selected-area electron diffraction. II) EXPERIMENTAL RESULTS The mechanical testing data are summarized in Table 111. The values reported are the average of

Jan 1, 1965

By John M. Gallow

Discussion of the paper of JOHN M. CALLOW, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2321 to 2339. R. H. RICHARDS, Boston, Mass.-I think there is one note which would be interesting to have recorded in connection with this paper, and that is another form of flotation machine. The Minerals. Separation machine has a vortex action, with a vertical shaft and a propeller. This new frother has been developed for the Copper Queen Co. at Bisbee, Ariz. It has a horizontal shaft and a paddle wheel for a frother. It has eight cells, I think, all connected underneath in one continuous tank, and the only separation of the cells is in the upper chambers where the froth is. When this paddle wheel goes around it throws out the froth and the sand goes to the bottom and drifts over from the first to the second cell, where it is paddled again, and comes out with its froth; the sand goes to the third cell where it is again beaten. In that way the sand is continually drifting toward the last cell, while each new froth remains in its own cell. You can see in the working of this machine just the same effect that you see in Callow's machine, i.e., the earlier cell has the darker or richer froth, and the latter has the lighter or poorer froth until you get to the farthest one-which has very little froth, and is very light. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-Speaking from the metallurgical standpoint, it is quite desirable, in many cases, that the oil be removed from the concentrate in order to facilitate the metallurgical work, and I think attention should be directed to the desirability of removing from zinc sulphide concentrates the oil which interferes with their subsequent roasting. The value of the oil is not large; in Mr. Callow's plant, for instance, it would be $20 a day, and it may be possible that a process might be developed which, within the limits of the value of the oil, would remove it, and thus facilitate the metallurgical treatment. LEONARD WALDO, New York, ,N. Y.-The question came up about a year ago as to why-Mexican crude was not an admirable oil for flotation. I have never heard any satisfactory answer to the question. The Mexican crude has the peculiar property of comparative freedom from dangers of fire, a very great reluctance to part with its water, and a specific gravity almost identically the same as water.

Jan 5, 1916