Search Documents

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By W. V. Kotlensky, H. E. Martens

In an earlier communication, Ref. 1, the authors presented the tensile properties and the changes in crystal structure and microstructure for pyrolytic graphite tested at 2750°C. It was suggested that changes in the structure may have an effect on the tensile properties of this material. Accordingly, tensile tests were run on a series of specimens, from one block of pyrolytic graphite, some of which were hot-worked by being strained at 2750°C, others of which were tested in the as-deposited condition. According to the manufacturer, General Electric Co., the polycrystalline material was deposited at 2100°C on a substrate of synthetic graphite by decomposition of a dilute natural gas mixture. The as-deposited material had a density of approximately 2.19 g per cc, and as shown in Fig. 1 had a structure of medium size growth cones which were regenera-tively nucleated. All specimens had a gage section 0.75 in. long by 0.06 in. wide by 0.1 in. thick with the thickness direction perpendicular to the basal planes. The testing method and equipment used have been previously described, Ref. 2 and 3. For both the hot-working and the testing the load was applied parallel to the basal planes; a cross-head speed of 1.5 x l04 in, per sec was used. All heating was done in an atmosphere of bottled helium.

Jan 1, 1962

By John W. Sweeney

Florida is blessed with some of the worlds greatest phosphate rock deposits, and doubly blessed in that those deposits are uraniferous. Until recently, the uranium con¬tained in phosphate rock had been ignored, but spot mar¬ket prices in the $40-per-pound range have spurred actions which will soon transform the state into a major uranium supplier. In 1978, two plants in Florida and one in Louisiana went it on- stream to recover uranium oxide from phosphoric acid, and construction began on three other extraction facilities. Together, these six plants will be cap¬able of recovering 1940 t/y (2140 stpy) of yellow cake from Florida phosphate in the early 1980s, equivalent to 15% of the projected US requirement. By the year 2000, Florida phosphates will have produced a projected 49 000 tons (54,000 st) of uranium oxide to fuel the nation's nuclear reactors.

Jan 9, 1979

PICK AND SHOVEL CLUB, CASE SCHOOL OF APPLIED SCIENCE The last meeting of the year of the Pick and Shovel Club of Case School of Applied Science was held on May 20, 1919. The speaker, Dr. Zay Jeffries, gave a very instructive and interesting talk on the Metallography of Non-ferrous Metals. The club has had a very successful year in spite of the loss of a few months time through the S. A. T. C. Among the speakers for the year were Dr. F. R. Van Horn, Dr. C. H. Fulton, and Dr. W. R. Veazey of our school; Dr. E. S. Moore of Penn. State College; Dr. Ansel St. John, of the National Carbon Co.; and Mr. V. S. Bidle, of the W. S. Bidle Co. The graduating members wish the club the best of success for the coming year. BERTRAND R. WARMELING, Secretary.

Jan 7, 1919

By AIME AIME

THIS year's Chairman of the Mineral industry Education Division is, like his predecessors, no novice in that field, having been in 1928 Chairman of the Engineering Education Committee which labored so well that it was enlarged into a Division of the Institute's activities . For almost a quarter of a century lie has been a dean in mining and engineering schools, with considerable experience before that as a teacher. A native-born New Englander (June 23, 1881), he naturally went to Massachusetts Institute of Technology where he received the Bachelor's degree in mining in 1904. Just why a Fitchburg. Massachusetts boy yearned to he a mining engineer he has never explained, but why should any boy ever have to explain why lie wants t? be a mining engineer? Like the old rhyme about the reasons why a man should drink, "any other reason why" is adequate..

Jan 1, 1945

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

R. B. T. KILIANI, Denver, Colo. (written discussion *).-Mr. Len-nox's paper is decidedly interesting in that he shows that a field exists for the Chilean mill, in which its efficiency compares favorably with that of more modern grinding devices. The figures he has given clearly indi-cate that a coarse feed is conducive to higher efficiency than the fine feeds which the Chilean mill has usually been called upon to grind. The fact is also apparently indicated that operating the Chilean mill in closed circuit with a mechanical classifier results in still higher efficiency, and that in such cases the percentage of returns should be kept below 100 per cent. to obtain best results. It would be interesting to see the results of further tests with what Mr. Lennox calls "Mixed Feed," since the data given in Table 4 seems to' point to the fact that a mixed feed,

Jan 12, 1919

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Charles L. Mantell, George Ferment

This investigation determined the jeasibility of current-potential curves as an analytical tool for monitoving manganese electroicinning solutions for metallic impurities. Nine metallic impurities were studied: trickel, cobalt, silver, copper, zinc, molybdenum, catlmiun magnesium, and sodium. The individual effect of each metallic irzplrl,iLy on the standard point-izatiorr was determined for a range of 'concentration. Not all of Ihe impurities affected the polarization curve; correlation between transition current and cotrcetztration of impurity. Molybdenum had an uncorrelated effect on the polarization curie. The effects of binary mixtures of impurities were studied to see if the transition current of the mixture could be predicted. Interactions occurred between impurities which prei'etzted the pvecliction the transition current of tile rrlisLitr.e by additive laws. The polarization curve was shown to be sensitive to metallic impurities which affect the current efficiency of a manganese cell. THE application of current-potential curves in manganese electrowinning is not new but played an important part in the conversion of an inoperative large-scale pilot plant into a continuous comnercial operation.1"" The effects of trace metallic impurities in manganese electrowinning solutions on cathode current-potential curves,5-19 specifically nine impurities (nickel, cobalt, silver, copper, zinc, molybdenum, cadmium, magnesium, and sodium) were studied for a range of concentrations. Cadmium, magnesium, and sodium had no effect. Nickel, cobalt, silver, copper, and zinc yielded a correlation between transition current and concentration of impurity: molybdenum had an uncorrelated effect. Binary mixtures of impurities were studied to de-termine if the transition current could be predicted from the values for the individual constituents. Interactions between impurities prevented the prediction of the transition current of the mixtures by an additive law. The polarization curve was shown to be sensitive to metallic impurities which affected the rurrent efficiency of a manganese cell. The electrowinning of manganese relies upon maintaining a high-purity electrolyte. Purification schemes were developed to remove all of the heavy metals, the magnesium and calcium. Concentration limits have been established for single impurities. With high-purity electrolytes, favorable cell efficiencies are consistently obtained; but with impure solutions there is a reduction in efficiency. With the rapid rise to commercial prominence of electrochemical processes, there has been a lag in developing rapid methods for determining whether an electrolyte is sufficiently pure for efficient electrolysis. The most sensitive test for impurities is the behavior of the electrochemical cell. Impure electrolytes will cause a serious reduction in cell efficiency, and in many cases metal deposition will be prevented or reversed. The effects of impurities are not usually evident until after long periods of electrolysis, resulting in a disruption of the process. A method which could predict the behavior of an electrolyte in terms of cell efficiency prior to reaching the commercial cell is needed. Van Arsdale and Maier," Allmand and Campbell,a1'22 and others attempted to develop an electrochemical process for manganese,"3"29 but all met with some degree of difficulty. Jacobs et a studied the effects of metallic impurities in manganese electrowinning. Plant methods were based on a 2-hr plating in a small electrolytic cell. The final method was based on a 24-hr plating run, performed in a relatively large test cell. Here, current efficiencies were calculated with and without impurities in the electrolyte, and the critical concentration was established as the maximum amount of impurity that the electrolyte could tolerate before there was a serious loss in efficiency. The amount of impurity that could be tolerated decreased as the plating time increased, indicating deposition of the impurity. This test duplicated the conditions of commercial practire, and was sensitive to impurities. Small amounts of impurities significantly affect the hydrogen overvoltage at a metal surface, increasing or decreasing it depending upon the nature of the impurity. ockris established the limit for the onset of poisoning at 10-l moles per liter. The effects of impurities were studied by potential-time curves at a constant current density. The technique did not lend itself to rapid analysis in that several hours were needed to establish stable potential-time curves. Serfass and coworkers3' developed calorimetric and spectrophotometric techniques for analyzing for trace impurities. Our method4'" is based on current-cathode potential curves produced by continuously changing the cell voltage at a programmed rate. Starting with a clean stainless-steel cathode, the cell voltage was initially adjusted to yield zero current: the program was then started and the current was plotted as a function of the cathode potential. Fig. 1 is a typical current-potential curve. In initial region A the hydrogen-evolution reaction predominates and the polarization curve

Jan 1, 1967

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications-those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicating and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement CO. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible.

Jan 2, 1958

By William Gilman

IN the past five years, and without much fanfare, Turkey has emerged as a significant figure in the world mining picture. This has been accomplished by a five-year plan now in its last year. A second five-year plan is already under way, ahead of schedule. It will concentrate even more than the first in developing Turkish mines in order to increase present exports of coal, chrome ore, and copper, and to develop new mineral exports as well. To be fully understand the republicic?s mining program should be considered as something more than merely tapping rich resources in the East along the Aegean Sea, in the North among the mountains descending to the Black Sea, and in the West at the foot of the Taurus Mountains. It should also be viewed in the light of a strong nationalist policy with many aspects of state socialism. Turkey declares frankly that all mineral re- sources belong to the nation and all exploitation should be by the state for the twin purpose of modernizing the state and securing foreign exchange for the state by exports. Accordingly, the principal mines are state-operated and a few lesser enterprises, although not state-owned, have at least been put in the hands of Turkish capital.

Jan 1, 1938

By A. W. Fahrenwald

THE absolute efficiency of crushing and grinding in a ball mill is not known. A number of investigators have made calculations to this end and have presented efficiency figures. Two factors have prompted further investigation of this subject: (1) the unbelievably low magnitude of the values offered, and (2) a desire to obtain, if possible, true relationships between the relative efficiencies of a ball mill operating under varying conditions. A useful forward step in the study of mill efficiency was made when Martin1 and Gross and Zimmerley2 proved the correctness of Rittinger's law, and incidentally the incorrectness of the so-called Kick law, and when Gross and Zimmerley3 determined and gave surface values for Tyler sieve-sized quartz. These data are probably accurate throughout the range of the sieve scale, but on -400 mesh (which is the finest sieve available), the surface data, as obtained by the hydrofluoric acid disso-lution method, are of doubtful reliability. Any inaccuracy existing in surface determinations of -400-mesh material, especially when comparing runs in which varying quantities of this product are formed, will cause the resulting relative mill efficiency values to be distorted. Moreover, knowing surface accurately, the efficiency calculations require a surface energy figure. Two such figures are to be found in literature, one by Edser4 and one by Martin.5 Edser's surface energy

Jan 1, 1931

By AIME AIME

TUESDAY afternoon the annual meeting was devoted to a general session, in the auditorium, on production control. George Otis Smith presided and in opening the meeting recalled that the session in 1920 on the stabilization of the coal industry was the first time this subject had been discussed by Institute members in a general session and then introduced Carl Snyder, of the Federal Reserve Bank of New York, who spoke on "Long-time Growth and the Factors In Its Variations." He spoke without notes and a full presentation of his views must be deferred until the stenographer's report is available. He said that of the total production some 80 to 90 per cent represents goods for consumption and the other 20 to 10 per cent for construction. He discussed various indices of production, concluding that bank clearings are the best, and showed by charts that when they are plotted, allowing for various disturbing factors, they are seen to increase quite regularly at the rate of about 4 per cent per year. The production curve rises at only 3y2 per cent per year, because agricultural production does not in- crease as fast as manufacturing postal revenues in- crease at the rate of 5 per cent per year while the use of electricity increases twice as fast.

Jan 1, 1929

By Allan E. Martin, Harold M. Feder, Irving Johnson

The cadmium-uranium system was studied by thermal, metallographic, X-7-ay and sampling techniques; special emphasis was placed on the establishment of the liquidus lines, The single inter metallic phase, identified as the compound UCd11 melts peritectically at 473°C to form a-umnium and melt containing 2.5 wt pct uranium. The cadmium-rich eutectic (0.07 wt pct uranium) freezes at 320.6°C. Solid solubilities in uraizium and cadmium appear to be negligible. Between 473°C and 600°C the liquidus line is retograde. NO publication relating to the cadmium-uranium phase diagram was found in the literature. The establishment of this diagram was of considerable interest to us because of a possible application of the system to the pyrometallurgical reprocessing of nuclear fuels. Analysis of liquid samples, metallographic examination, thermal analysis, and X-ray diffraction analysis were used to establish the phase diagram from about 300° to 670°C. Particular emphasis was placed on the establishment of the liquidus lines. The same system was concurrently studied in this laboratory by the galvanic cell method.' Both studies benefited from a continual interchange of information. MATERIALS AND EXPERIMENTAL PROCEDURES Stick cadmium (99.95 pct Cd, American Smelting and Refining Co.) contained 140 ppm lead as the major impurity. Reactor grade uranium (99.9 pct U, National Lead Co.) was most often used in the form of 20-meshspheres. This form was particularly suitable because it does not oxidize as readily as finer powder. The liquidus lines were determined by chemical analysis of filtered samples of the saturated melts. The liquid sampling technique is described elsewhere2 alumina crucibles (Morganite Triangle RR), tantalum stirring rods, tantalum thermocouple protecthecadmiumtion tubes, Vycor or Pyrex sampling tubes, and grades 60 or 80 porous graphite filters were used. Uranium dissolves in liquid cadmium rather slowly. In order to achieve saturation of the melts it was necessary to modify the procedure of Ref. 2 by the use of more vigorous stirring and longer holding periods (at least 3 hr) at each sampling temperature. The samples were analyzed for uranium by spectro-photometry (dibenzoyl methane method) or by polar- ography. The analyses are estimated to be accurate to 2 pct. Thermal analysis was performed on alloys contained in Morganite alumina crucibles in helium atmospheres. Standard techniques were employed; heating and cooling rates were about 1°C per min. For the determination of the peritectic temperature, Cd-10 pct U charges were first held for at least 50 hr at temperatures in the range 435° to 460°C to form substantial amounts of the intermediate phase. For the determination of the effect of cadmium on the a-p transformation temperature of uranium, charges of Cd-25 pct U (-140+100 mesh uranium spheres) were first held near the transformation temperature, with stirring, to promote solution of cadmium in the solid uranium. The holding times and temperatures for these treatments were 18 hr at 680°C for the cooling run and 28 hr at 630°C for the heating run. Alloy specimens for X-ray diffraction and metallographic examination of the intermediate phase were prepared in sealed, helium-filled Vycor or Pyrex tubes. Ingots from solubility runs and thermal analysis experiments also were examined metallographically. Crystals of the intermediate phase were recovered from certain cadmium-rich alloys by selective dissolution of the matrix in 20 pct ammonium nitrate solution at room temperature. Temperatures were measured with calibrated Pt/Pt-10 pct Rh thermocouples to an estimated accuracy of 0.3°C. However, the depression of the freezing point of cadmium at the eutectic is estimated to be accurate to 0.05°C because a special calibration of the thermocouple was made in place in the equipment with pure cadmium just prior to the measurement. EXPERIMENTAL RESULTS The results of this study were used to construct the cadmium-uranium phase diagram shown in Fig. 1. This diagram is relatively simple; it is characterized by a single intermediate phase, 6 (UCd11), which decomposes peritectically, and which forms a eutectic system with cadmium. The solid solubilities in the terminal phases appear to be negligible. An unusual feature of the diagram is the retrograde slope of the liquidus line above the peritectic temperature. The Liquidus Lines. The liquidus lines above and below the peritectic temperature are based on three separate solubility experiments. The data are shown in Fig. 1 and are given in Table I. It is apparent from the figure that the solubility data obtained by the approach to saturation from higher temperatures fall on substantially the same lines as those obtained

Jan 1, 1962

By J. J. Rutledge

THE first method of working coal mines in the middle western states, more particularly in Illinois, Indiana and Missouri, was by means of the so-called single-entry method. In this method a single main passageway, or entry, was driven in the coal seam. with no parallel passageways, and from this pas-sageway or entry there were turned at intervals sim-ilar cross-passageways or entries, and from these cross-passageways, if the coal seam worked lay fairly horizontal, rooms were turned right and left. These crude methods of working were followed when the com-panies opening the mines were small and of very limited capital, and when the demand for coal was small and irregular. The principal desire was to produce coal in the short-est possible time and at the cheapest price. The chief evil resulting from such method of working was de-fective ventilation, although there were other serious drawbacks. There were then few or no good mining laws and no restrictions on those operating the coal mines. The hours of labor were long, the wages low, and the miners accordingly worked hard. All the coal was either sheared or undercut with a pick by hand. Very little solid shooting and no machine mining was done. What little air entered the mine, openings was introduced through the entries or. headings and thence conducted through the rooms by means of curtains; in many cases, as the workings became more exten-sive, the number of curtains added so materially to the mine resistance that ventilation was extremely in-efficient. Shots were fired by the miners at any time during the working shift and consequently there was more or less powder smoke or fumes in the mine work-ings all day long. Moreover, the working days were much longer than at present. The fine, dry coal-dust falling from the miners' picks while they were shear-ing or undercutting the coal filled the mine atmosphere and was taken into the lungs of the mine employees.

Jan 2, 1927

By R. G. McQueen, E. G. Zukas

THE production of isotropic fine-grained ingot iron would be most useful since physical measurements associated with the elastic properties of iron are influenced by the size and orientation of the individual grains. This can be accomplished at present for small samples by established metallurgical procedures, but for large samples (in excess of 2 in. diam by 1 in. thick) it is virtually impossible to produce reasonably small uniform grains with random orientation. Such pieces can, however, be produced by impulsive loading followed by a suitable recrystallization treatment. The shock loading system employed is diagrammed in Fig. l. Here the 3/8-in. iron plate is accelerated by the plane-wave initiated high explosive charge through a 1 5/8-in. air space. Collision of this plate and the specimen of interest generates a shock wave in excess of 300 kbars which passes through the specimen. For this type of work it is not necessary to use machined parts: for example, the ingot iron pieces are saw cut from the billet so that they can be inserted in short sections of iron pipe. The recovered specimens are less distorted, however, if the air gap between the iron sample and pipe is filled with Woods metal. The dimensional changes resulting from this type of loading technique are minor, usually less than a 10 pct reduction in thickness. Compressive yield

Jan 1, 1962

By Wheeler P. Davey

When metals are subjected to mechanical working, such as rolling, one of the phenomena that take place is a movement of the crystals of the metal into a system or systems of orientation which bear an angular relation to the direction of working. In rolled metal the crystals may orient themselves with respect to the rolling plane or the rolling direction, or both. Direct evidence of the existence of preferred orientations in rolled metal has been obtained by numerous investigators from X-ray patterns of the rolled metal. Most of these workers used a monochromatic pinhole method. Where the degree of preference for a single orientation is high the monochromatic pinhole pattern may be interpreted by a geometrical calculation based on the angular relationships of the planes in the crystal and the diffraction arcs on the X-ray pattern. This process may be aided by the geometrical construction of the locus sphere (Lagenkugel), and reflection circles of Polanyi,l Polanyi and Weissenberg,2 and Mark and Weissenberg,3 and of the plane polar figures (flachenpolfigur) of Franz Wever.4 R. M. Bozorth5 solves X-ray patterns from metals having a single preferred orientation by means of a series of charts which when placed over the X-ray pattern give directly certain angular relationships, between the crystal planes and the surface of the specimen.

Jan 1, 1930