Search Documents

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By Lester L. Hirst, Arno C. Fieldner, Henry H. Storch

EXPERIMENTAL work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogenation of bituminous coal and tar by the Bergius-.I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 lb. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydrogenation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. EQUIPMENT AND GENERAL PROCEDURE OF RESEARCH The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By J. F. Mitchell, R. Bainbridge, E. A. Melvin

IN the fall of 1953, The Consolidated Mining and Smelting Co. of Canada Ltd. put into operation a completely new and modern plant for sintering the rather complex assortment of materials which comprise the feed to the Lead Smelter at Trail, British Columbia. This Lead Smelter is one section of an integrated metallurgical plant producing lead, zinc, silver, gold, cadmium and other metals. Since most of the incoming lead concentrate contains appreci- able zinc values, and most of the zinc concentrate similarly contains appreciable lead values, the cross-routing of residues or tails from the respective lead and zinc plants offers obvious advantages in recovery of metals, and has been practiced for many years. A disparity has existed, however, between the output of zinc plant residue and the capacity of the Lead Smelter to treat it, with the result that over the years a stock-pile of residue had been accumulating, and by the end of World War II had reached the formidable total of half a million tons. To treat this stock-pile, in addition to all current zinc plant residues and, of course, the regular quota of lead concentrates, became a prime objective of the Lead Smelter following World War 11. As zinc plant residue plays an important part in the operations to be discussed in this paper, some consideration of its

Jan 1, 1958

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By William Firmstone

ON the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: "Sixthly, though I cannot, and do not, claim am exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the Journal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of an¬thracite with hot-blast on the 7th February, 1837, in a cupola blast-furnace, 41 feet high, and 10' feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), and had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

Jan 1, 1875

By Fredrick C. Kruger

Introduction This surprisingly little-known group of minerals, the nonmetallics, so-called for their lack of metallic luster, is the largest group of the mineral kingdom, and cinstitutes perhaps 75 percent of all mineral species. For the most part, these minerals are compounds of the common acids, oxides, hydroxides, and two elements, carbon and sulfur. The list of the non- metallic minerals, therefore, is very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulfates, and less commonly, arsenates, chromates, molybdates, suliides, tungstates, and vanadates, the latter groups, and many of the oxides, being sought principally for their metal content. Those nonmetallics used commercially are generally called the industrial minerals, although in addition this term also includes a considerable group of rocks. The list of industrial minerals and rocks is continually growing as new uses are found, and it now numbers over 300 commodities. The industrial minerals industry has developed since about 1920. There- fore, the development has been fast, and it has been more or less parallel with the development of the art of minerals beneficiation. General Discussion of the Group This group is so heterogeneous that it has defied logical, or widely accepted, classification, whether by origin, composition, or end use, and perhaps for this reason the industrial minerals generally have received short shrift in both teaching and research. Except for those involved with asbestos, cement, fertilizers, gypsum, salt, sand and gravel, few large companies have deigned to enter the field, and consequently most industrial minerals have been developed for the most part by the small operators or entrepreneurs. Yet surprisingly, except for one war year, the nonmetallics have always surpassed the metals in value and tonnage (Fig. 1). One main characteristic that most of the nonmetallics have in common is direct sensitivity to labor and transportation. In other words they are characterized by large bulk and low-unit value, and hence have what might be termed a "place value".

Jan 1, 1971

By Edward W. Parker

At the Cleveland meeting of the Institute, October, 1912, I had occasion to call attention to the general though erroneous impression that the principal mining activities of the United States lie west of the 100th meridian of longitude. Few, I believe, realize that the States east of the Mississippi river, which comprise only 28.8 per cent. of the total area of the United States, exclusive of Alaska, contribute about two-thirds of the total mineral production, computing by values. In 1910 the percentage of the production credited to the Eastern States was 67; in 1911 it was 65. When I have, with becoming modesty, ventured to speak of these comparisons, I have usually been met with the rejoinder, " But you include coal." I surely do, for whereas coal (m petroleum, as natural gas, as limestone) is not in the strictly technical definition of the word, a " mineral," it is legally mineral, is certainly a mineral substance, and contributes by far the largest tonnage and approximately one-third of the total value of all mineral products. The production of coal-mines in 1911 weighed approximately 500,000,000 tons. In 1912 it exceeded that record by nearly, if not quite, 50,000,000 tons. According to H. D. McCaskey, of the U. S. Geological Survey, the total weight of all the metallic ores mined in the United States in 1911 was 105,000,000 tons (a little more than one-fifth that of coal). In 1910 Mr. Lindgren estimated the total weight of all metallic ores at 120,000,000 tons. The products of the quarries, clay-pits, oil-wells, phosphate-mines, and other non-metallic products, taken all together, did not in 1911 weigh in excess of 300,000,000 tons, so that the output of coal exceeds by 25 per cent. the combined tonnage of all other mineral products. The coal-mines give to

Jan 1, 1914

By E. G. Spilsbury

AS a fresh illustration of the advances made in the past few years in the overhead-cable systems of hoisting and conveying, as applied to open-cut deep mining and quarrying, I would call attention to a further development of this system of transportation which has lately been put in operation i-n this State. A few miles above Williamsport, on the Susquehanna river, the Glen Union Lumber Company, of Pottsville, Pa., owned a large tract of valuable timber-

Jan 1, 1892

By F. W. McQuiston

Idarado Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949

The Report on the Manufacture of Coke for the year 1880 by J. D. Weeks1 includes an historical account of the early days of coke-making that is very complete and accurate, and but little can be added to it to fully cover the period prior to 1885. The few additional references that have been found follow. The earliest suggestion found about making coke in this country is in a letter from D. M. Randolph to Harry Heth, dated August 22, 1808. Heth was then operating the mines in the Richmond, Virginia coal field and had sent Randolph to England to investigate steam engines for hoisting and pumping and other conditions in the coal industry there. The letter was written in London and said: "I shall explain to you, how, by turning Deep Run fine coal in Coak, to make great profit from what has heretofore been useless. You will do well to ascertain the price and amount of demand for this article throughout the U. States among brewers and manufacturers. I know how also to make every bushel of such fine slaty coal, fetch as much as any of the best grate coal, by turning it into Coak: and that too, after paying all expenses of the process."2 His interest was to use the slack more for domestic purposes than otherwise, probably, although what the interest of brewers would be in coke as fuel does not appear. Nothing ever came of this suggestion, and so far as known, no coal from this field was coked excepting in gas-making. The Plumpsock Iron Works, mentioned by Weeks as having used coke, was advertised for sale in June 1818.3 It was stated that stone coal was the only fuel used at the works, the pit being within 100 yards of the forge. "Three men with a horse and cart are sufficient to raise coke, and haul to the forge all the coal necessary for keeping the works in full operation." The coke, of course, was made in ricks, or heaps, and not in ovens. The first real coke oven in this country was probably built in Connellsville, the coal coming from a mine nearby on Mounts Creek. L. L. Norton operated an iron foundry and was persuaded by his foreman, one Nichols, who came from Durham, England to build a coke oven. The oven was 12 feet square, and the first coke was produced in 1833. Later

Jan 1, 1942

H. H. Campbell, Steelton, Pa. (communication to the Secretary) : I wish to thank Mr. Webster for the copious quotations he has made from my writings, as he has given nearly all the arguments I wish to advance. It is necessary to note, however, his statement that most of his experiments were made on universal-mill plates, and that these were not subject to my condemnation of irregularity. I think this is a mistake. It is well known that universal-mill plates are finished under very different conditions of temperature, with the express purpose of regulating the tensile strength. This is a perfectly legitimate practice; but it renders almost worthless any calculations on the relations of the chemical and physical equations when the influence of such finishing is omitted. Another important point Mr. Webster has not answered at all. I have shown by an excerpt from his own table that two entirely different formulæ may be constructed; and it is undeniable that one is as valid as the other, since Mr. Webster started with no premise at all save an assumption that the effect of carbon was constant. This was an assumption pure and simple, and hence has no special virtue. The whole result of Mr. Webster's investigation is not that the effect of carbon is a constant, and that those of phosphorus and manganese are variables. On the contrary, there are two answers, with nothing to show which is right. We learn that if carbon is a constant, then phosphorus and manganese are variables; but that if phosphorus and manganese are constants, then carbon is a variable. This is a distinct advance over complete ignorance, but it is not final and satisfactory from either a mathematical or metallurgical standpoint. Regarding my own formulæ, I would say that they are used regularly in the testing-laboratories of the Pennsylvania Steel Company. The tensile strength of every heat is calculated

Jan 1, 1899

By W. A. Bates, R. J. Miller

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By R. J. Miller, W. A. Bates

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By A. L. Holley

THERE is a growing demand for pure and cheap material for fine open-hearth steel ; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90' per cent. of the phosphorus from the pig iron. 2. Krupp's washing process (the conduct and results of which I fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States: 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the Catalan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens's process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be squeezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I have watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the waste-ful treatment of the direct product. With one or two exceptions (when failure was due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.'s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By William Firmstone

On the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: " Sixthly, though I cannot, and do not, claim an exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the .Joozcrnal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of anthracite with hot-blast on the 7th February, 1837, in a cupola blastfurnace, 41 feet high, and 10 feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), arid had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

By F. G. Miller, E. B. Wilson

In 1972, coal mine productivity was in steady decline and labor and maintenance costs were spiralling upward. Yet, despite this sad state of affairs, nowhere in the US at that time was there a comprehensive and coordinated coal research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. It was during this period that Bethlehem Steel Corp. determined that a new approach to coal mining research was needed for the industry as well as for the company itself. After studying Bethlehem's own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, a comprehensive research package was presented to company management in late 1972. The ideas and experience of many operating and management personnel in the company contributed to the formulation of the final plan as approved.

Jan 10, 1976