Search Documents

T. T. READ, Secretary of the Committee on Industrial Organization, presents the following very interesting monthly ad interim report: Reports from London are to the effect that 750 housing schemes for workers, involving the erection of 128,000 new dwellings, have been submitted to the Local Government Board. Birmingham alone needs 14,000 new houses, and the Housing and Town Planning Committee of the City Council considers that 5000 new houses must be built each year for the next 20 years. Nine hundred acres of land has been acquired, on which to build 10 to 12 houses per acre for the next two years. The town of Dudley, which built 300 modern dwellings in 1915-1916, submitted schemes for another 500 houses. There is a shortage of building materials required, specially brick. Financial assistance has been received for reopening brick yards that were closed during the war. W. E. Dickson, vice president of the Midvale Steel & Ordnance Co., is reported in the daily press as stating that his corporation is planning to spend $8,000,000 in improving its plant and assisting its employees in building their own homes. The company will advance 90 per cent. of the cost of the house and extend payments over a period of 12 years. Methods of work employed in building 256 houses at Quincy, Mass., for the workers of the Fore River shipyards are described, by Joseph Meltzer, in the Engineering News Record for May 29, 1919. The approximate cost was about $3500 per house, not including water supply, sewers, streets, and sidewalks. "Comparative Costs of Tenantry and Home-Owning;" "A Plain Talk on Helping Home-builders;" and "More Plain Talk on Home Building" are the titles of three publications of the Information and Education Service of the Department of Labor. These publications should be' of a good deal of service in convincing employees that it is to their interest to own their homes rather than to live in rented houses. The same Service has issued pamphlets discussing the cost of materials.

Jan 7, 1919

By David White

The submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safeguard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immcdiatc review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the graund. With the members of this cooperative committee, state geologists, regional geologists, oonsulting specialists, and geologists and engineers attached to many companies worked both independently and through subcommittees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnsont Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman. Oil geologists and engineers understand well the speculative nature and the chances of error that must attend estimates of the petroleum in the ground when they cover not merely prospective territory, but possible territory. Neither the character nor the magnitude of the factors of uncertainty is to be disguised. Further, the inevitable differences of opinion between geologists of equal rank and experience must also bc

Jan 1, 1923

By David White

The submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safeguard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immcdiatc review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the graund. With the members of this cooperative committee, state geologists, regional geologists, oonsulting specialists, and geologists and engineers attached to many companies worked both independently and through subcommittees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnsont Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman. Oil geologists and engineers understand well the speculative nature and the chances of error that must attend estimates of the petroleum in the ground when they cover not merely prospective territory, but possible territory. Neither the character nor the magnitude of the factors of uncertainty is to be disguised. Further, the inevitable differences of opinion between geologists of equal rank and experience must also bc

Jan 1, 1923

By R. V. Norris

THE wage rates and working conditions in the anthracite. region of Pennsylvania have been governed for nearly 20 years by the award of the Anthracite Coal Strike Commission, appointed Oct. 16, 1902, by President Roosevelt. The report of this com-mission, made in March, 1903, was accepted and, with eight modifications made at various dates, has had .almost the force of law, and has kept this great indus-trial region free from strikes for almost a generation. In 1920, President Wilson appointed an Anthracite Coal Commission, and its report, accepted Aug. 30, 1920, governed wage conditions to April 1, 1922. Actually, the agreements have been for terms of two to four years, and lately, in 1916 and 1920, the employ-ees have continued at work pending the negotiation of new agreements which were made retroactive, and which have all been modifications of the original 1903 award. With the expiration, April 1, 1922, of the 1920 award approaching, Mr. Lewis, president, of the United Mine Workers of America, addressed a letter, on Feb. 20, to the operators, suggesting a meeting on March 15; this date was accepted by the latter, with the notation that the time was short. At the meeting, the Mine Workers presented 19 demands, and advised that if a satisfactory agreement was not reached by April 1.a suspension of mining would occur, contrary to the practice since 1916 of continuing work with a retro-active adjustment.

Jan 6, 1922

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.' Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.'." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960

By Henry J. Williams

The main difficulty in the determination of silicon in pig-irons containing very high percentages of that element, has been due to their almost complete insolubility in acids, or mixtures of acids. The object of the present paper, which presents no new principle, is to suggest a method of determination which has repeatedly given accurate results, and which obviates completely the tediousness and uncertainty of the usual slow solution in acids. This method has been tried with pig-irons containing from 7 to 14 per cent. of combined silicon, and properly called ferro-silicons. When reduced to an impalpable powder in the agate mortar, an 11 per cent. ferro-silicon was found to resist the action of all acids, or mixtures of acids, with the exception of sulphuric acid of about 1.25 specific gravity. But the action of this acid, even during long continued heating, was very slow, 72 hours being necessary to com pletely dissolve half a gramme of the metal. The complete decomposition of 1 gramme of the metal may, on the other hand, readily he effected in a few minutes by fusion with sodium carbonate in a covered platinum crucible over a blast-lamp —the idea being to dissolve the silicon, leaving the iron in condi tion to be readily attacked by acids. The silicon dissolves as soluble sodium silicate, and metallic iron remains in a very spongy and finely divided condition. The addition of a little hot water

Jan 1, 1889

By Howard Smith

AT the meeting of this Institute in February 1933, I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey's 20-year search for commercial sources of soluble potash minerals and of the events, that led to the discovery, exploration, and first development of the deposits in that state. As a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by. G: R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area .of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K20; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1935

By Harry R. Hall

THE proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the successful work that has been done under these adverse conditions warrants a permanent record in our Transactions, especially as it furnishes a comparison with, coke blast-furnace practice under similar conditions. The record of the furnace-practice is briefly summarized as follows:-The charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates containing from 62 to 65 per cent. of iron would pass in. screen, of which about 34 per cent.. would pass an 80-mesh sieve. The cobbed ore, varying in composition from 32 to 47 per cent. metallic iron and from 23 to 32 per cent. of. silica, would pass through a I-in. ring, of which about 25 per cent. would pass a 1/8 in. screen. The furnace was blown in October 20,1903, with charcoal which was supposed to weigh when dry 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year and was then found to weigh 12 lb. per bushel. During the first 10 days of the blast, the furnace produced 362 tons of pig-iron, using 200 bushels of charcoal per ton of iron. From November 1st to 12th, the volume of the blast was increased gradually from 2,808 to 5,460 cu. ft. per minute, with practically no increase of output. The silicon-content of the resultant pig-iron averaged 0.75 per cent., with sulphur about 0.035 per cent. A supply of freshly-burned dry charcoal was then used which increased the silicon-content and lowered

Sep 1, 1905

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By Thomas T., Read

T HE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established,, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently , attempted to make a much too simple correlation between mineral -discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail.

Jan 1, 1941

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By J. F. Wolff

During the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision were done in a few instances only. The demand for refinement of work in .this direction has led 'the engineers of the Oliver Iron Mining Co. to do extensive structural subdivision and correlation in all exploration work during the past 4 years. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Rangc, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7,1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principal feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will be as follows : I. General geology. 11. Subdivision of Biwabik iron-formation. 111. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgnlent is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron Mining Co., for permission to use the information presented in this paper.

Jan 1, 1917

By J. F. Wolff

DURING the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision was done in only a few instances. The demand for refinements of work in this direction has caused caused extensive structural subdivision and correlation to he done in all exploration work during the past 4 years by the engineers of the Oliver Iron Mining Co. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Range, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7, 1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principle feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will he as follows: I. General geology. II. Subdivision of Biwabik iron-formation. III. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgment is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron. Mining Co., for permission to use the information presented in this paper.

Jan 10, 1916

By J. A. Woolf, E. S. Leaver

The presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. Part I.—Copper in Cyanidation The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results. Azurite, bornite, chalcocite, cuprite, malachite and finely divided metallic copper are readily and completely soluble under the usual conditions for cyanidation. Enargite and tetrahedrite are sufficiently soluble to cause an excessive loss of cyanide, and they also cause fouling of solutions with arsenic and antimony. Precious-metal ores containing small percentages of chalcopyrite or chrysocolla may give satisfactory returns with the usual cyanidation.

Jan 1, 1930

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested 'I'he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14' taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By Sidney Siegel, J. Gardner Brooks, Irvin R. Kramer

IN 1942 Grossmann1 proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigators2-5 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent [ ] upon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a hite quench than predicted by Grossmann's factors for an infinite quench (Table I). [ ] Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Grossmann's grain-size correction curves, deter- mined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1946

By P. H. Royster

SOMETHING of a mystery has attached itself to the production of ferromanganese in the blast furnace. This alloy has been produced on the Continent almost continuously since 1876 and in very considerable tonnages, but little definite information concerning the practice is to he found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country prior to 1904, bit one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public. In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many, as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations. Realizing the advantages both to the country and to the industry from a pooling of operating data and experiences, the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Although the results of this investigation have already been reported to the companies cooperating, they may he of permanent metallurgical interest, so this paper attempts to give, briefly, the more important points brought out in the investigations. OPERATING DATA IN FERROMANGANESE PRACTICE Operating data were collected by the Bureau from 11 ferromanganese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P. The dimensions, of seven of the furnaces are given in Table 1. The companies from whom this infor-

Jan 2, 1919

By John Birkinbine

EXTENDED discussions, by inviting attention to problems affecting the conservation of natural resources, have encouraged investigations as to their sufficiency, with the general result that the more thorough the examination, the less cause appears for anxiety as to the exhaustion or serious depletion of these resources. The extent of industrial development, the large plants and the enormous volumes of materials required, when compared with conditions a few decades ago, are sufficiently startling to enlist the attention of those who "fear .the pace," and yet in but few instances has real solicitude for the future. been warranted by a knowledge of true conditions. In a former communication, presented 5 years ago,1 I endeavored to emphasize the fact that true conservation represented the best utilization of reserves and not the locking up of resources for future use; a conviction which has become more pronounced as the subject was investigated. Prophecies of the, early exhaustion of mineral resources have raised the question as to our permanent reliance upon these, and encouraged inquiries which have in most cases developed reassuring conditions. But the fact that the future appears less dark than prognosticated cannot excuse wastefulness or improvidence; and detailed study which demonstrates an apparent abundance of natural resources should encourage their best application. In making inventories of resources one is liable to confine conclusions as to availability upon present circumstances and conditions in the past, or to formulate data for the future upon methods which are rapidly being displaced. In reserves which are not reproductive, such as minerals, the possibilities of exhausting the supply are startling if estimates assume that future extensions will follow methods which were less economical than those now employed, or to he used, and we dare not claim that the limit of advanced practice has been attained.

Jan 9, 1914