Search Documents

By G. W. Toop

In a recent publication,31 Darken has derived an equation to describe thermodynamic behavior in ternary metallic solutions with compositions near pure component 1: Eq. [I] is understood to be a general equation, consistent with the ternary Gibbs-Duhem equation, which is proposed as a logical formalism in view of observed behavior in some binary metallic solutions31'32 rich In Eq. and am are constants obtainable from the 1-2 and 1-3 binaries. The parameter 023 may be determined from measurements on the ternary The purpose of this discussion is to compare Eq. [I) or [3] with other ternary formulations involving binary terms, within the regions of validity of Eqs. [I], [2], and [3]. First, the ternary point is considered to be at the intersection of two composition paths, one with constant N1 and another with constant N2/N3 as shown in Fig. 10. The terms in Eq. [3] may be related to the binary points shown by multiplying the first term on the right-hand side of Eq. [3] by N2 (1) /l -N1, the second term by the third term by and the fourth term by each multiplier being unity: It should be noted here that no suggestion has been made that either the binary or the ternary systems form regular solutions. However, Eq. [5] and hence Eq. [3] shows that the contribution made to the ternary excess free energy from the 1-2 and 1-3 binaries has the same form as for a regular ternary system.1 Before considering the term a23 for the above case, a second geometrical relationship is examined with the ternary point at the intersect ion of three composition paths with constant N1/N2, N2/N3, and Nl/N3, respectively, as shown in Fig. 11. For this geometry, ternary values of NZ and N3 in terms of the binary values shown may be substituted into Eq. [I]. Then by making use of identities of the form Eq. [6] contains terms that are similar to those in a ternary regular solution formulation34 based on the geometry shown in Fig. 11. Although at finite concentrations, unless the 1-2 and 1-3 binaries form

Jan 1, 1968

By B. Lustman

IT has been known for a number of years that the addition of certain alkaline-earth and rare-earth metals to nickel-chromium base electric resistance alloys causes marked increase in their oxidation resistance as measured in an intermittent oxidation test similar to the ASTM—B 76-39 test. However, the mechanism whereby such additions confer protection is still unknown. On the basis of the experimental observation that the increase in life in intermittent tests of nickel-base alloys is proportional to the atomic radius of the added element, Hessen-bruchl has proposed that the added metal ions occupy holes in the oxide lattice which prevent diffusion of nickel ions in the oxide. Horn2 has postulated that the effect of such additions is to accelerate the rate of diffusion of chromium atoms in the metal and thus to favor the formation of Cr2O3 scales. Hickman and Gulbransen3 concluded from electron diffraction observation that the addition of the elements in question results in the formation of a barrier to the diffusion of nickel ions to the surface. In connection with some experiments conducted to develop a test for the resistance to oxidation of alloys in massive form under conditions of intermittent heating and cooling, some features of the oxidation of nickel-chromium base alloys were revealed which may serve to elucidate the mechanism of protection conferred by rare-earth and alkaline-earth elements. Specimens of cylindrical shape 0.360 in. diam x 0.37 in. long were placed in alumina thimbles and inserted into and withdrawn from a Globar-heated furnace operating at 2150°F at 7.5-min intervals. The weight of oxygen absorbed as well as the weight of oxide spalled were measured at intervals. With the particular experimental conditions used, the specimens in a 7.5-min cycle were at temperature for 2 min which corresponds to the heating time of the ASTM test. The weight changes of similar specimens under conditions of continuous heating in air at 2150°F were also measured. The specimens after oxidation were examined metal- lographically and samples of the spalled oxide collected for X-ray diffraction identification of the phases. The specimens used were from the same lot of material used by Hickman and Gulbransen3 and had the compositions shown in table 1. Included in table I are results of ASTM life tests on the materials in the form of wires. These materials, their composition and the ASTM life test data thereon were all supplied by F. E. Bash of the Driver-Harris Co. It may be noted that alloy 13246 of 80 pct nickel, 20 pct chromium nominal composition showed the shortest life in the ASTM test; alloy 12246 with the addition of small amounts of the elements zirconium, calcium, and aluminum, intermediate life; and alloy 12046 with the further addition of silicon, the longest life. In fig. 1 are shown the results of intermittent oxidation tests made on bulk specimens at 2150°F as well as continuous tests conducted at the same temperature. Duplicate tests were made on each specimen. The ordinate scale, inches of metal oxidized, was derived from the experimentally observed weight gain of oxygen by assuming the scale to be entirely Cr2O3. It may be noted that the metal-loss curves during intermittent oxidation show a constant or continuously increasing rate of weight

Jan 1, 1951

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

By F. R. Brotzen, A. R. Troiano, E. L. Harmon

Precipitation processes leading to drastic property changes are a frequent occurrence in titanium alloys containing large amounts of the retained high temperature P phase. In order to establish the kinetics and nature of these precipitation processes, a series of Ti-V alloys was studied. Time-temperature-transformation diqgrams were obtained for 12.5 and 15 pct V-Ti alloys. These diagrams consisted of two intersecting C-shaped curves: one in the high temperature region for the euilibrium transformation P +u+P, and another at lower temperatures depicting the formation of the meta-stable transition phase, o. Presence of the transition phase retarded the precipitation of the equilibrium a phase. Deformation of retained P resulted in the formation of the o phase. Reversion and retrogression phenomena of the transition phase were observed. A negative temperature coefficient of resistance was found in quenched alloys containing from 15 to 20 pct V. CERTAIN titanium-base alloys can be heat treated to produce appreciable changes in properties. For example, remarkably high hardness values may be obtained by aging or isothermal quenching treatments. Most of the information available to date on the hardening of titanium-base alloys has been systematized recently in an article by L. D. Jaffe.&apos; It was pointed out by that author that the hardening was the result of the decomposition of the retained j3 phase to the equilibrium constituents, a and p, and that this decomposition had many of the characteristics of an age-hardening reaction. Recent work by Frost et al.&apos; 3 has contributed much to the fundamental understanding of the hardening mechanism in titanium-base systems. These authors established the presence of a transition phase in the transformation from j3 to a + j3, which they designated o. The transition phase, in their opinion, was at least partially responsible for the hardening and embrittling effects which accompanied low temperature aging. The present investigation of the mechanism and kinetics of the hardening reaction was carried out for the Ti-V system. Ti-V alloys were ideally suited for a study of the decomposition of j3, since age hardening was known to occur readily in this system." Moreover, no intermetallic compounds occur in this system, Fig. 1, thus simplifying the interpretation of the results. Material and Procedure Alloys containing 12.5 and 15 pct V were prepared by Battelle Memorial Institute from iodide titanium furnished by Watertown Arsenal and vanadium of 99.8 pct purity. Ingots of 8 Ib each were prepared by arc melting in an inert atmosphere with a tungsten electrode and water-cooled copper crucible. Each of the ingots was melted once, forged at 1600°, and rolled at 1400°F. Following this, the ingots were remelted, forged, and then rolled to % in. sq bars, which were subsequently grit blasted, pickled, and wire brushed. Another set of alloys containing nominally 17.5 and 20 pct V was produced by the Research Div., New York University. These alloys were arc melted in an inert atmosphere in lots of 20 g each. Heat-Treating Procedure: Whenever feasible, specimens were heat treated in high vacuum resistance furnaces at pressures below 5x10." mm of Hg. Aging and isothermal quenching treatments were generally carried out in salt baths. Specimens were not attacked by the salt, provided the tempera-

Jan 1, 1956

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07&apos;, the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace &apos;Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier&apos;s experiment................ 248 2. Wolkoff&apos;s experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914

MINING ASSOCIATION, UNIVERSITY OF CALIFORNIA At a meeting of the Mining Association of the University of California, held Feb. 12, officers for the present semester were elected as follows: President, Richard C. Kerr, &apos;19; vice-president, Glen T. O&apos;Brien, &apos;20; secretary, Kenneth V. King, &apos;19; treasurer, Sam Grinsfelder, &apos;20. KENNETH V. KING, Secretary.

Jan 4, 1919

By W. E. Horst

Flotation feed was hell constant for batch laboratory tests and continuous pilot and commercial plant tests on a spodumene ore to determine the relation.ship between flotation behavior and the size and type of flotation machine. Results. showed that additional retention time would be needed in the plant flotation circuit to duplicate laboratory or pilot plant performance when operating Dariables of the. plant flotation machines remained unchanged. During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pct) and about twice that of the laboratory (21.0 pct). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation. Measuring Flotation Rates: Efficiency of the rougher stage was measured by flotation rate, defined as the recovery that can be attained within a given time." • The problem of measuring flotation rates has been studied by many investigators, whose methods have varied. Published studies an flotation kinetics have been summarized recently by Gaudin.l When comparing flotation rates, it is more satisfactory to compare straight line relationships between recovery and flotation time than exponential curves resulting from plotting cumulative recovery vs cumulative flotation time. To convert the exponential curves into straight line relationships, rate equations were applied similar to those used in chemical kinetics to study the velocity of chemical reactions. Two rate equations have been used in this investigation to measure efficiency of the various cells: 1.5 order Rate Equation dR/dt=k (A-R)1.0 [Eq.1] Second Order Rate Equation dR ---- - K(A - R)2 [Eq. 2] dt Upon integration Eq. 1 becomes 1/(A-R)1/2=k/2 t+1/A1/2 [Eq. 3] and Eq 2 becomes: or fEq. 4] t/R=1/A2K+t/A [Eq. 4] where R = cumulative recovery [percent recovery of total value (spodumene) in flotation feed]. A = initial concentration, pct (100 pct of mineral to be separated). t = flotation time (minutes). k = flotation rate constant for 1.5 order rate equation [units: 1/(percent) 0.5 (min)1. K = flotation rate constant for second order rate equation [units: 1/(percent) (min) 1.

Jan 1, 1959

J. E. Stead, Middlesborough, England (communication to the author): Prof. Howe&apos;s valuable paper on cast-iron brings forward most prominently the correct explanation of the part played by combined carbon in pearlite and cementite, in determining the strength and hardness of cast-iron. On a previous occasion I haveoshown that castings made by melting a white Cleveland iron and glazed iron, one containing 1.5 and the other from 4 to 5 per cent. of silicon, and each about 3 per cent. of carbon, were stronger than those made of ordinary foundry-iron; the difference in the final castings being a differ-

Jan 1, 1902

By Gerhard Derge

THE chemical and physical properties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use, These processes are carried out at high temperatures and involve such complex chemical systems that fundamental scientific knowledge of the properties and behavior of these slags is inadequate. Various hypotheses have been proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenck1 and the recent papers of Chipman and co-authors.2-5 Another proposal is that these compounds dissociate by completes or partial ionization, the evidence for which has been reviewed by Martin and Derge.7 Whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: I, Studies of solidified slag samples by X-ray diffraction, petrography, and similar methods that can be used at room temperature, The correlation of this information with the high-temperature properties of the molten slag is uncertain, 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature, However, even these data present problems of interpretation because they require a complete knowledge of the metal phase, 3, Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret, Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information, The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems CaO-SiO2 and CaO-A1203-Si02 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1946

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations&apos; and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)&apos;0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson&apos;s ratio, and Young&apos;s modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young&apos;s modulus, s is Poisson&apos;s ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman&apos;s measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.&apos; When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg&apos; lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson&apos; in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of&apos; the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft &apos;-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,&apos; no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By E. E. White

I DISAGREE with Mr. Brinsmade on several points, and I will discuss his remarks under the same six topics which he has used. 1. Rate of Interest Earned by Sinking-Fund.-I believe Mr. Brinsmade is confused in his ideas as to the effect of new gold on the interest earned on money. The flood of gold which he mentions certainly should not operate, to increase interest rates, but since it replaces and adds to liquid capital should reduce interest rates and counteract the destruction of liquid capital which he mentions. Furthermore, it is doubtful if the destruction of capital since 1897 by wars and catastrophes has been any greater in proportion than in similar periods before 1897. With regard to savings banks, I would say that only 3 per cent. is allowed on deposits through a large part of the West. As to bonds, they can be bought to yield any rate. of interest desired up to 6 per cent., but, a 5 per. cent. bond is not as safe as a 4 per cent. bond, nor a 4 per cent. bond as safe as a 3 per cent. government security. I do not understand why Mr. Brinsmade says that Mr. Denny&apos;s quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer War. Certainly there is no reference to the Boer war or to English conditions in Mr. Denny&apos;s article. M. Howard Burnham, in his admirable work on mine valuation, says&apos;: ". For instance, redemption is taken at 3 per cent., because even 4 per cent. represents a greater risk, as is indicated by the purchase of Government paper to bear only 3 per cent., the great desideratum of the .latter being security." . Again, Mr. Burnham says:2 "The tables are calculated on the assumption that the dividends shall accumulate at 3 per cent. only, as in accordance with the general idea set out elsewhere, a rate greater than 3 per cent. involves appreciable risk with which it were inaccurate to saddle the sinking-fund if risks are to be segregated, this being the basis of all the writer&apos;s calculations."

Jan 6, 1914

By T. Kilner, A. Plumtree

DURING an investigation of electro-deposited silver structures, samples were prepared for metallographic examination by cold mounting in plastic, grinding on successive grades of emery paper down to 3/0, and chemically polishing by swabbing using the chromic acid solution described by Gilpin and Worzala.1 Attempts to etch these samples using the standard solutions described for silver (e.g., 5 pet KCN-5 pet Na2S2O8, H2O2-NH4OH, and various potassium dichro-mate solutions) all failed to give good results due to staining of the samples and to rapid etching. The staining was caused by the chromic acid polishing solution being trapped in small fissures between the sample and the mounting plastic, and also in small fissures in the sample itself. To overcome these difficulties, an etchant was developed which prevented staining at the same time as it slowly etched the sample. This resulted in a very clean, crisply etched surface as shown in Figs. 1 and 2. This etch consisted of 10 ml of orthophosphoric acid, 10 ml of distilled water, and 2 drops of the polishing solution noted above,&apos; which is made by mixing 100 ml of saturated CrO3 solution, 45 ml of 10 pet HC1 solution, and 800 ml of distilled water. The etching procedure involved taking the final polished sample, either immersing or swabbing in the etchant for a period of 1 to 2 min, rinsing as quickly as possible in distilled water, alcohol, and ethyl ether in that order, and then immediately drying. This etch is easily controlled due to its slow rate of etching, and produces samples with clean, sharp surfaces. Pits due to overetching produced varying contrast effects when viewed under polarized light, and are therefore obviously useful for revealing many structural details within the sample. Another effect of overetching was to produce a height varia-

Jan 1, 1968

By Chung Yu Wang

DURING the time I was in charge, of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:&apos; "The iron ores at Tayeh lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between horn-blende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende." These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General Description of the Deposits The deposits are situated to the west of the Yangtse River, being con¬nected with the river by a standard-gage railroad of 56 li (16.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 3, 1917

By Chung Yu Wang

During the time I was in charge of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:&apos; "The iron ores at Tayeh * * * * lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between hornblende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende."&apos; These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General DescriptLon of the Deposits The deposits are situated to the west of the Yangtse River, being connected with the river by a standard-gage railroad of 66 li (18.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 1, 1918