Search Documents

By J. Philibert, A. G. Guy

Diffusion in the presence of deformation was studied by the method of vacuum dezincification of copper-rich and silver-rich solid solutions containing 7 to 30 pct Zn. The specimens were designed to permit the study of diffusion in separate portions of a given specimen characterized by strain rates ranging from essentially zero to approximately 10 sec-. No effect of deformation on diffusion was observed. BEGINNING with the work of Buffington and Cohen: interest in the question of the effect of stress or strain on diffusion has largely been concentrated on the enhancement of diffusion in specimens subjected to Continuous plastic deformation. The present research is a contribution to this limited area. However, as a preliminary to focusing attention on this special topic, it will be desirable to make a broad survey of the larger question, especially since there has been considerable foreign work in areas outside those of current interest in the United States. Since most of the topics referred to in the following section are both complex and imperfectly understood at present, it has been expedient in most instances to offer only a guide to the general nature of the work rather than a critical evaluation. PREVIOUS WORK The effect of elastic stress on diffusion has received considerable attention, especially with regard to the thermodynamic driving force for diffusion. The thermodynamic treatments have been based on the work of Gibb, Voigt, Planck, and Leontovich.' Konobeevskii and Selisski6 made a first attempt at treating the problem in 1933, and Gorskii7 a few years later gave a solution applicable to single crystals as well as to polycrystalline specimens. In 1943 Konobeevski8 published treatments that have been the basis of much Russian work up to the present. For example, Aleksandrov and Lyubov used his work in explaining the velocity of lateral growth of pearlite. Early work in the United States was that of Mooradian and Norton, which showed that lattice distortion tends to be relieved before it can significantly affect the diffusion process. Druyvesteyn and Berghoutl1 observed a slight effect of elastic strain on self-diffusion in copper, while de Kazinczy12 found that both elastic and plastic deformation increased the rate of diffusion of hydrogen in steel. On the other hand, Grimes58 observed no effect of either elastic or plastic straining on the diffusion of hydrogen in nickel. High-frequency alternating stresses have been reported by various investigator s13-l5 to increase the rate of diffusion. A special form of elastic stressing is the imposition of hydrostatic pressure, a condition that is amenable to Conventional thermodvnamic analysis. Most of the experimental results in this area are consistent in showing a slight decrease in diffusion rates at high pressures.16-l8 Although Geguzinl reported a pronounced effect of relatively small pressures, Barnes and Mazey20 failed to Corroborate this finding, while Guy and Spinelli21 advanced an explanation of the phenomenon observed by Geguzin. It has been recognized that the thermodynamic treatment of diffusion phenomena in an arbitrarily stressed body is complicated by the fact that the desired state of quasi-equilibrium of the shear stresses cannot be maintained during a general diffusion process. However, attempts have been made by Meix-ner22-24 and Fasto to treat certain restricted cases, such as relaxation. FastovZ7 has also incorporated the general stress tensor into the thermodynamics of irreversible processes. The lattice strain that accompanies the formation of a solid solution has been the subject of much study,28-s0 and indirectly it has entered into many recent theories of diffusion. However, some Russian investigators31'32 have taken other views of this matter and have predicted large effects on diffusion rates because of concentration stresses.o In completing this brief resume of previous work involving elastic strains and before proceeding to a consideration of the effect of continuous plastic deformation, it should be pointed out that deformation of various additional types may also influence diffusion. The effect of cold-working on subsequent diffusion has been studied directly by AndreevaS and by Schumann and Erdmann-Jesnitzer, while indirect evidence has been obtained by Miller and Guarnieri and by Vitman.38 Thermal stresses may also influence diffusion, contributions to this subject having been made by Fastovs7 and by Aleksandrov and Lyubv. The work of Johnson and Martin,o Dienes and Damask,3Band DamaskS considered the question of radiation-enhanced diffusion. In considering previous work on the subject of plastic deformation and diffusion, attention will be directed to those studies concerned primarily with diffusion rather than with its relation to Creep, e.g., the work of Dorn, or to the acceleration of diffusion -controlled reactions. Observations of the effect of

Jan 1, 1962

By N. H. Jensen, B. L. Sackett, Carlos Bardwell, Simon Jacobson

Lead smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was molded into bullets. With the development of the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 21/2 ft. in diameter, and smelted from 3 to 10 tons in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This procedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Furnace capacity was about 14 tons per day, with a campaign of about 16 days. Cost of smelting was about $44 per ton. The ores making the

Jan 1, 1926

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

By Michael B. Bever, Barton Roessler

The effects of deformation by wire drawing at 78OK on initially ordered and initially disordered specimens of the alloy Cu3Au were investigated. The resistivity, stored energy, drawing force, and microhardness were measured as functions of strain; microstructural changes were observed. The results are interpreted in terms of the structural imperfections and the changes in atomic configuration resulting from deformation. A few experiments on the effects of room-temperature annealing after deformation at 78°K were made; they suggest vacancy-promoted ordering in disordered alloys. BARTON ROESSLER, Junior Member AIME, formerly Graduate Student and Alcoa Fellow, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass., is with Westinghouse Research Laboratories, Pittsburgh, Penn. MICHAEL B. BEVER, Member AIME, is Professor of Metallurgy, Massachusetts Institute of Technology. Based in part on o thesis by B. ROESSLER submitted in October, 1959 to the Massachusetts Institute of Technology in partial fulfillment of the requirements for the degree of Doctor of Science. Manuscript submitted April 6, 1961. IMD AN investigation of the effects of deformation at room temperature on the alloy Cu3 Au was reported in a recent paper,' which included a review of the literature on the deformation of order-disorder alloys. In general, plastic deformation of ordered alloys reduces the degree of long-range order and causes corresponding changes in their properties. Deformation of disordered alloys changes their properties in a manner characteristic of solid solution alloys; these changes can in part be attributed to the destruction of short-range order. The effects of deformation on solid solution alloys are of two kinds: 1) generation of structural imperfections, which occurs as a result of deformation in any metallic system including pure metals, and 2) changes of atomic configuration, which are characteristic of solid solutions and particularly of order -disorder systems. These two types of effect are not independent of each other and the state of a deformed solid solution alloy is determined in a complex manner by the way in which the structural imperfections cause changes in atomic configuration both during and after deformation.

Jan 1, 1962

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By B. C. Craft

Oil and gas development in Mississippi during the year 1933 was rather active and a number of important wildcat wells were drilled throughout the state. Mississippi showed an increase in drilling operations during 1933. There were 58 completions from 22 counties during this period, compared with 53 completions in 10 counties during 1932. The Jackson gas field in Hinds and Rankin counties continued to be the most active area with 26 completions, resulting in 17 gas wells, 2 oil wells, and 7 dry holes, compared with 38 gas wells, 1 oil well and 5 dry holes during 1932. A further attempt to extend the producing limits of the Amory gas field resulted in a dry hole. Extensive exploration in south Mississippi has proved the existence of ample source beds and presence of an extensive sandbody near the top of Cockfield. Core tests, supplemented by extensive geophysical work, have been carried on in Jackson, George, Harrison, Pearl River and Stone counties. Exploration will be continued in 1934. The most important deep test drilled in 1933, and the deepest well ever drilled in a southeastern state, was the Eastman Gardner et al., Bank of Seminary No. 1, sec. 26-8N.-15W., Covington County. This well went through about 1300 ft. of Selma chalk, and was abandoned in the Eutaw at 8004 ft. Another interesting operation during the past year was the Foster Creek Oil Corporation's Foster Creek Lumber Co. No. 1, sec. 14-2N.-2W., in the "Eastern Conroe Trend." This test is shut down at 3687 ft. in the Catahoula sandstone and has not encountered any important shows of oil or gas. A total of 107 of the 117 gas wells completed in the Jackson gas field since its discovery in 1930 are still producing, and have a combined open flow of approximately 3,724,896,000 cu. ft. It is reasonable to assume that this area will be rather inactive during 1934 as the maximum daily production during 1933 was 3,476,000 cu. ft. The 10 wells that have gone dead were edge wells. The water level is now between the sub-sea depths of 2190 and 2195 ft. The Gulf Refining Company's Rainey No. 1, sec. 13-5N.-lE., one of the early wells in the field, had gas and water at —2225 ft. That the field is under hydraulic control is

Jan 1, 1934

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By Bert S. Sandell

Much has been said and written about the various uses of die castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100" F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500" F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties. Alloys Investigated Two types of alloys were used in this investigation—zinc-base and aluminum-base alloys. Two alloys of each group were included. Those most generally employed in the industry at present were selected. Alloys A and B are of the same nominal composition, and correspond to A. S. T. M. alloy XXI, containing 4 per cent aluminum, 3 per cent copper, 0.1 per cent magnesium, and the balance zinc of 99.99 per cent

Jan 1, 1932

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By ROBERT B. COONS

SELECTIVE SERVICE must meet three important demands for man power: (1) Activities concerned with production of war goods. (2) The armed forces. (3) Civilian activities and institutions the continuance of which are essential to maintaining the structure of our American democracy. In the above enumeration of demands I have placed everything, including most of our most prized possessions and activities, after the demand for men for war production and the armed forces. To establish an order between the latter two is difficult. For the time being, at least, the Selective Service policy is to make sure that we avoid the risk of "too little and too late." No soldier, sailor, or marine should be sent from these shores to risk his life without the assurance of having a gun, clothes, food, and medical supplies. Therefore, the premium is now being placed on man power for war production and in our process of selection no stone is left unturned to see that our agencies are fully informed of the needs of war production. Our procedures set up recourses for employers of war-production man power so that their activities need not be disrupted, at least not until they have had time to train replacements.

Jan 1, 1942

By L. Ekstrom, J. P. Dismukes

The homogeneity and microstrcture of zone-leveled Ge-Si alloys haw been investigated by sellera1 physical techniques and by metallography as a function of growth rate in the range 3 x 10 1x10 cm-sec', and as a system of alloy composition throughout the system. The temperature gradient at the solid-liquid interface was about 50 deg-cm-' Cellular or dendritic structures char-acteristic of constitutional supercooling were ob-served except at very slow growth rates, which ranged from about 2 x 10 cm -sec for Ge 1 sio alloy to about 2 X 10'5 cm-sec'1 for Ge .sSio.s alloy. Using a simple model similiar to that employed for dilute solid the dependence upon compo-sition over the entire system of the critical growth rate for the onset of constiutional supercooling was calculated, and was .found to he in good agreement with the experimental results. THE recent discovery of the low thermal conductivity of Ge-Si alloys' at high temperatures has revealed that these alloys have high efficiencies for thermoelectric-power generation.', Therefore, a reliable method was needed for the preparation of homogeneous samples required for definitive measurements throughout this alloy system. Due to the low diffusion rates in the solid alloys, the segregated samples obtained by quenching a melt are not readily homogenized by annealing.475 However. isothermal solidification from a melt of constant composition can produce uniform material. Of the available semiconductor crystal-growth procedures, the zone-leveling technique6 applied to a complete solid-solution alloy system by Wang and Alexander' and by others provides a simple method of doing this. In the present work, the homogeneity and microstructure of zone-leveled alloys have been correlated with growth conditions, and the conditions for preparing homogeneous Ge-Si alloys have been established. This has provided insight into the solidification process of alloy semiconductors. EXPERIMENTAL PROCEDURE Sample Preparation. The Ge-Si alloy phase diagram4 shown in Fig. l(a) consists of a complete series of solid solutions. The zone-leveling technique used to prepare most of the samples consists of moving a zone of liquidus composition (C1) through charge material of the corresponding solidus composition (C,), as is illustrated in Figs. l(b) and l(c). To prepare the charge materials, high-purity germanium and silicon were pulverized in a steel hammer mill, cleaned magnetically, and melted together to make uniform chill castings. The zone leveling was carried out in a resistance-heated furnace similar to that of Mitrenin et al.' shown in Fig. 2. However, a few specimens of high silicon content were prepared by the Czochralski technique. The growth rate ranged from 3.5 x X6 to 1.2 X 10~3 cm-sec-'. Temperature gradients in the solid and in the melt were determined by recording the temperature as the molten zone passed over a Pt-Pt 13 pct Rh thermocouple contained in a small

Jan 1, 1965

By B. L. Sackett

LEAD smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was. molded into bullets. With the development of. the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as, the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 2 1/2 ft. in diameter, and smelted from 3 to 10 tons. in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This pro¬cedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Fur-

Jan 8, 1925

By C. E. Wood

THE Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1939

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

By William M. Bowron

THIRTY years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. THE PRESENT THEORY. Referring to this subject, Dana says:' "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued. . . The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, south and west, could not have formed in an open sea, for clayey iron-deposits do not form under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Nov 1, 1905

By W. P. Barba

IN THE early summer of 1917, it became evident that the then existing sources of supply of guns and gun forgings were totally inadequate for the enormous and rapidly growing requirements of the Ordnance Department of the Army, so arrangements were made with sixteen makers of other products to take up the manufacture of guns and gun forgings. Nine of these makers were required to produce their own steel from the raw materials and convert it into rough machined gun forgings; the others finished and assembled these forgings into completed guns. In December, 1914, four of these makers of steel and rough gun forgings were instructed to manufacture the same amount of the 6-in. and 9.5-in. guns and howitzers. It, therefore, seemed practical .and profitable to assemble these makers into a small group, together with the officers of the Ordnance Department, and provide standard 'equipment in each of the four works for the production of these two types of guns. The advantages of this cooperation were immediately manifested, and there commenced an interchange of shop practice and a free discussion of facilities and methods that covered not only the equipment but the manufacturing processes.

Jan 1, 1920

By C. P. Sandberg

Notwithstanding the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests,—that of the producer and that of the consumer,—and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark,.have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years; but the recent revival of the rail trade has been the more gratifying to mo, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881

By C. P. Sandberg

INTRODUCTION. NOTWITHSTANDING the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests, -that of the producer and that of the consumer,-and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark, have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years ; but the recent revival of the rail trade has been the more gratifying to me, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with .feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881