Search Documents

By Arthur L. Christenson, Clarence E. Jackson

IN the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition1 may be corrected to the grain size observed in an actual weld,2 or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.3 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2100°F. has been used. In studies of the end-quench hardenability specimen quenched from 2100°F. instead of from a lower temperature of 1700°F., it is important to ascertain the relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6,7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been proposed: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching. temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1943

By Gerald J. Anderson

The Marquette District of Central Northern Michigan is the oldest of the Lake Superior iron districts with a mining history dating from 1852 up to the present. The total production of all types of ore through 1965 was 338,120, 146 long tons. Emphasis up to the 1950's was on mining the direct shipping ores; however, demands for higher-grade and better-structured ores in the last decade has resulted in a complete shift in emphasis to beneficiating the lowgrade Negaunee Iron-formation to produce high-grade iron ore pellets. The Precambrian sediments of the Marquette Range have been correlated with the Animikie Series of the Thunder Bay District, Ontario, and are contained in a westward plunging synclinorium that is approximately 3 3 miles in length and 3 to 6 miles in width. -The rock unit of major economic importance is the Negaunee Iron-formation that reaches a thickness of 2500 feet near the City of Negaunee. The primary iron content of the Negaunee Iron-formation averages 26 per cent, whereas the altered iron-formation approximates 31 per cent. The Negaunee Iron-formation has been divided into three principal types: diagenetic, oxidized, and metamorphic. The ores produced to date fall into four categories: high-grade soft ores, high-grade hard ores, siliceous ores, and concentrates and agglomerates (pellets). The soft ores generally are found in synclines and in fault-trough structures, bounded by mafic dikes along at least one side, and are mainly found in the basal portion of the Negaunee. In contrast, the hard ores occur in the uppermost portion of the Negaunee and are controlled by structural features such as folds, faults, and dikes. Iron-formation that has undergone diagenetic and metamorphic alteration makes up the main beneficiating ore types. Studies on the Negaunee Iron-formation have played an important role in the formulation of many of the theories on the origin of the Precambrian iron-formations.

Jan 1, 1968

By Arthur S. Huey

AS the end of the collegiate year approaches, the problem of student employment again becomes acute. This subject divides itself into two phases: (1) employment prior to graduation and (2) employment following graduation. "Experience is the best teacher," according to the old adage, and the student needs all that he can get. He is afforded every opportunity to reap from his books the theories and principles of scientific and engineering practice, and occasionally he is privileged to make field trips to observe the practical side of the subject. But it is not enough for one to know the theory and to observe its application; it is also desirable for the student to get the feel of the tools during his training Such opportunities can only be afforded the student if the major companies cooperate with the universities in giving the student part-time and vacation work.

Jan 1, 1932

By H. D. Wilde

GREAT emphasis is being placed today on petroleum as a source of chemicals. Such prominence is well merited, for rapid strides have been made in developing processes for the conversion of petroleum into synthetic chemical products, which are now being made on a huge scale. These marvelous accomplishments have resulted in some highly optimistic predictions as to what can be expected in the future. Many of these forecasts are well justified, but some writers, especially those contributing to the Sunday supplements and the popular-cience type of publications, have let their imagination run wild and present a rather distorted picture of the possibilities in this field in the postwar period. Commercial manufacture of synthetic organic chemicals had its beginning in England with the establishment of a plant by Sir William Perkin in 1857 for the manufacture of "Aniline Purple" or "Mauve." The preceding year he had discovered in the laboratory how this dyestuff could be made from aniline, one of the many derivatives of coal tar, and he soon made commercial application of his discovery. Influenced largely by his success, organic chemists began research on production of a vast array of synthetic dyestuffs, medicinals, flavors, scents, and explosives. Rapid progress was made and by the turn of the century hundreds of these products were being manufactured. Most of these synthetic chemicals were derived from materials obtained as by-products in the conversion of coal into coke. These by-products are generally referred to as "aromatics" and are obtained by processing coal tar recovered in the coking process, so they are popularly known as "coal-tar chemicals." During the early years of this century, coal-tar chemistry was the wonder of the age, and rightfully so, since the products so made seemed limitless.

Jan 1, 1944

By Walther Mathesus

INTRODUCTION THE use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100° F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800° and 1,000° F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available.

Jan 3, 1915

Jan 1, 1886

By James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to loo per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent SiO2, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By Oliver Bowles

GLASS razor blades, glass chairs, and marble window panes attest that creative genius was still active in 1935. Many less striking, though doubtless more important, developments are to be recorded for the nonmetallic mineral industries, and not the least of them is the establishment of an Industrial Minerals Division in the A.I.M.E. under the able leadership of Samuel H. Dolbear, Chairman. Thus the nonmetallics are rightly granted equal dignity with metals and fuels in the category of mineral industries. The brief review of progress that follows merely touches the fringe of important developments in this broad field.

Jan 1, 1936

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

Chairman James F. Kemp :—I call upon Prof. Albert Sau-veur to open the general discussion on the subject of sound steel ingots. Albert Sauveur, Cambridge, Mass.:—I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain Rome very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my views. I have always remembered my astonishment, not to say dismay, some twenty years ago, when I beheld for the first time a steel ingot, a rail steel ingot, that had been split open from top to bottom. There was the pipe! There was an enormous cavity extending from a short distance from the top to nearly one-third of the length of the ingot; and when I was told that manufacturers seldom discarded more than one-tenth of the total length of the ingot it became evident to me that a large proportion of piped, and therefore, defective, or at least weak and dangerous, rails were manufactured; in fact, probably one rail out of six, nearly 17 per cent., of dangerous rails.

Jan 1, 1914

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By G. Wranglen

On account of the possibility of isolating carbides in steel it is generally assumed that the electrode potential of iron carbide is more noble than that of ferrite.1,2,3,4,5 Differences from 0.032 V1 to 0.4 V4 have been recorded. However, it is important to realize that the more noble behavior of cementite in relation to ferrite is not an issue of thermodynamics but of reaction kinetics. Theoretically, cementite is less noble than ferrite, which is a direct consequence of its thermo-dynamic instability. With the value ?F°298 = +4700 cal per mol for the free energy of formation of cementite6 it is easily calculated that the electrode

Jan 1, 1950

By M. Cohen, P. E. Beaubien, D. Caplan

Addition of 1 pct Mn to Fe-26 CY ca/(ses a12 increase in scaling rate at 870° and 1090°C. Whereas only the rhombohedral oxide, formrs on tire manganese-free alloy, with manganese present major amounts of the spinel .Mn0 . Pro-duced through which diffusion is more rapid. At 1090°C the scale formed OH Mn is highly, irregular due to blistering and sintering, This is a second cause of faster oxidation Since much of the blistered oxide does not participate as part of the protective layer. The oxide phases that form at different times depend on the degree to which the surface metal has become depleted, in manganese by preferential oxidation. PREVIOUS work has demonstrated that the oxide scales formed on chromium steels at high temperature consist of both spinel and rhombohedra1 phases and may contain considerably more manganese, especially in the spinel phase, than is present initially in the alloy.' It has further been observed that a binary Fe-26 Cr alloy scaled less rapidly than an equivalent commercial steel and formed no spinel.' However, it is not established if manganese in chromium alloys actually promotes formation of spinel nor if it affects oxidation resistance. It seemed expedient to try to evaluate the specific effect of manganese by oxidizing an Fe-26 Cr alloy containing a small manganese addition under the same experimental conditions as used for the manganese-free alloy.' EXPERIMENTAL Table I shows the composition in weight percent of the Fe-26 Cr-1 Mn alloy and of the Fe-26 Cr alloy used as reference. The alloy with manganese was prepared from the vacuum-melted Fe-26 Cr alloy by remelting in vacuum with the proper manganese addition. The ingot was rolled to strip and specimens 1.1 by 0.035 by 5 cm and 1.1 by 0.5 by 4 cm cut out or machined. As previously described2 the specimens were smoothed by abrading through 600-grit Sic paper, electropolished in acetic-perchloric acid (20 to 1) to remove 10 p of metal, annealed at 1100°C in 20 torr of purified argon, and electropolished to remove a further 10 p of metal. They were then either rinsed in water and methanol and blotted dry or immediately etched for 45 sec in deoxy-genated 4 N HC1 under cathodic polarization at 10 pa per sq cm. Oxidation runs were carried out in a vertical tube furnace in a flow of purified oxygen at 1 atm while the weight increase was recorded continuously on a* automatic balance.3 Alter 98 hr at 870.C or 20 hr at 1090"C the specimens were removed to flowing argon and observed microscopically for evidence of spalling as they cooled. Subsequently they were examined by X-ray diffraction, the oxides analyzed chemically, and metallographic cross settions prepared. RESULTS Figs. 1 and 2 show the oxidation curves of Fe-26 Cr-1 Mn at 870' and 1090C. The Fe-26 Cr reference runs are shown as dashed curves. Experimental details of the six runs are included in Table 11. The first 20 hr of run 1 is repeated in Fig. 2 to show the effect of temperature. At 8'70°C the weight gain for Fe-Cr-Mn is about twice that of Fe-Cr (curve 1 vs curve 2, Fig. 1). Both alloys show regular oxidation curves. On parabolic coordinates (right-hand scale of Fig. 1) the

Jan 1, 1965

By R. L. Doan

WHEN the Plutonium Project was started in the spring of 1942 there was no technology to produce uranium metal of the required purity. Not only was there no such metal available; no one knew how to make it or fabricate it after it was made. Since this time vast technical effort has been ex-pended in the atomic energy field. A short 15 years later the metallurgy of uranium is probably better known than that of any other metal, with the possible exception of steel. At the beginning of the 1942 drive to obtain pure uranium metal the most available raw material was black uranium oxide (U3O8) of about 92 pct purity from the Great Bear Lake region of Canada. It took only three months for the project chemists to develop a process for bringing the purity of this oxide up to 99+ pct and another three months for Mallinckrodt Chemical Co. of St. Louis to build the purification plant and get it into operation. In early summer of 1942 the purified brown oxide (UO2) started moving to the Metal Hydrides Co. in Beverly, Mass., and to the Westinghouse Research Laboratory in Bloomfield, N. J., both of which had been granted Government contracts to try to make pure uranium metal.

Jan 9, 1957

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By C. Feng, P. Levesque

HE addition of rhenium to molybdenum is known to produce alloys with good workability.&apos; Lawley and Maddin found that the critical stress for twinning in this system was lowered by the addition of 35 pct Re, which suggests that twinning may re- place the usual slip operation as the major element of deformation. The twinning elements in bcc Mo-Re alloys have been reported as the (112) planes and the <111> directions.3 This note represents the continuation of this investigation, in which the authors found that the occurrence of twinning promotes the formation of a bcc tetragonal phase, previously identified as u by Greenfield and Beck.4 Specimens of Mo-35 pct Re alloy, prepared as described previusly, were solution annealed at 2400o, cooled to room temperature, and plastically deformed by compression to induce twinning. After subsequent aging for 8 hr at 1300°C, traces of a were observed along the grain boundaries and at the interfaces between the twins and the matrix, Fig. 1. With increased aging time the cr phase grew into larger clusters and finally occupied the entire twinned area, Fig. 2. Experiments also indicated that if twinning did not precede aging, there was no visible evidence of a in the microstructure.

Jan 1, 1962

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron&apos;s papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.&apos; Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron&apos;s two papers practically amount to a summation of his life&apos;s work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron&apos;s valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author&apos;s reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating and meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lb per ton U3O8, although there are very large reserves below this grade, Rio Algom is interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals. Rio Algom has been investigating various applicable preconcentration processes since the early 1950s to date, on laboratory and pilot-plant scale. Methods investigated include gravity concentration by sink-float, high intensity wet magnetic separation, flotation of uranium, flotation of acid consumers, and a number of electronic sorting methods including radiometric, photometric, and conductimetric. No method tested has yet been satisfactory under Rio Algom&apos;s criteria of uranium recovery and cost, principally because uranium loss has been too high for a useful weight rejection. Metallurgical results of the preconcentration test work and the economic assessment therefrom are reviewed.

Jan 1, 1974