Search Documents

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,' appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.' For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,' polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By E. Miller, K. Komarek, W. Johnson

The activity of aluminum in solid Cr-A1 alloys has been measured by an isopiestic technique between Cr-A1890' and 1126" and 13 and 80 at. pct Al. The integral free energy of mixing has a minimum value of —5600 cal per g-atom at 59 at. pct Al. The maximum solid solubility of aluminum in chromium was determined to be 43 at. pct Al, and the composition limits of the compounds CrA14, Cr4A19, and Cr5Al, at 1000"~ were found to be 79 to 80, 66 to 70, and 59 to 63 at. pct Al, respectively. The thermodynamic properties of the Cr-A1 system have been investigated as part of a thermodynamic study of aluminum-transition metal systems.172 Little information is available on the equilibrium properties of the Cr-A1 system. The heats of formation of solid Cr-A1 alloys have been determined by Kubaschewski and Haymer at 600" and low-temperature specific heat data have also been obtained.~ More extensive work has been performed on the phase diagram, and a compilation has been provided by Hansen and Anderko,~ their phase diagram at elevated temperatures being essentially based on the work of Bradley and LU.~ The high-temperature portion of the phase diagram shows an intermediate phase CrA14 decomposing peritectically at 1018°C and existing at 82 at. pct A1 at 1000°C. They also identified the compounds with solubility limits of 72 to 75 at. pct A1 at 1000°C, and Cr5A1,, existing at 61 at. pct A1 at 1000°C. The maximum solid solubility of aluminum in chromium at 1000°C was found to be 46 at. pct Al. These elevated-temperature data were obtained by examination of quenched samples and were considered as less precise than the lower-temperature data. Koester, Wachtel, and Grube7 have revised the phase diagram as a result of their magnetic susceptibility and X-ray study. The results of this work differ appreciably from those of Bradley and Lu at temperatures above 800°C. The CrA1, compound is given as existing between 79 and 81 at. pct A1 at 1000°C, and they do not indicate the presence of a CrA13 phase reported by Bradley and Lu. They also report the compound Cr4Alg as having solubility limits of 66 to 70 at. pct A1 at 1000°C, while Bradley and Lu show this compound stable only up to 870°C. Koester et al. state that the high-temperature modification of the compound Cr5A18 is stable down to 1125"C, and not 980°C as stated by Bradley and Lu, and that the low-temperature modification of Cr5Al, has a range of homogeneity of 58 to 63 at. pct A1 at 1000°C. They also report that the maximum solid solubility of aluminum in chromium is 43 at. pct A1 at 1000°C. APPARATUS AND EXPERIMENTAL PROCEDURE An isopiestic method was employed which has been successfully applied to the determination of aluminum activities in solid ~e-All and Ni-Al alloys. Alloy specimens were held at different positions in a temperature gradient and were equilibrated with aluminum vapor from an aluminum reservoir kept at the temperature minimum of an impressed thermal gradient in a closed alumina system. Diffusion of aluminum into the specimens occurred until equilibrium was reached, at which the partial pressure of aluminum in each of the specimens was given by the vapor pressure of the pure aluminum reservoir. The activity of aluminum referred to liquid aluminum as the standard state in a given equilibrated sample at temperature T could therefore be expressed by: vapor pressure of pure aluminum at _ the temperature of the reservoir Vapor pressure of pure liquid aluminum, at specimen temperature T Since both the temperature of the aluminum reservoir and the specimen temperatures were determined experimentally, and the vapor pressure of pure aluminum is known as a function of temperature,' the activity of aluminum in a given aluminum alloy of known composition could be calculated. Initial runs were made with samples consisting of pure chromium chips placed in alumina crucibles. These runs exhibited large inconsistencies, indicating that equilibrium was not attained. High aluminum content Cr-A1 alloy powders were therefore substituted for the pure chromium specimens. The starting composition of the alloys was adjusted through experimentation until the concentration change necessary to attain equilibrium was small. In this manner, consistent results were obtained in reasonable times. SPECIMEN PREPARATION Alloy specimens were prepared from chromium of 99.997 pct minimum metallic purity: with 0.028 to 0.038 pct H, 0.0002 pct N, and 0.27 to 0.46 pct 0 (Aviquipo, Inc.). The aluminum had a purity of 99.99+ pct and the following impurities: 0.003 pct Cu; 0.002 pct S; 0.002 pct Fe; 0.001 pct Pb; 0.001 pct Ga (Aluminum Corp. of America). Alloy powders were prepared from weighed mixtures of chromium and aluminum by double-arc melt-

Jan 1, 1969

By Howard N. Eavenbon

The low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent, The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper. Geological Position of Seams The smokeless seams are among the oldest coal seams in the country, as the Pocahontas group of rocks is the lowest member of the coal-bearing series and rests on top of the Mauch Chunk red shale, in or below which no coal seams of any importance occur. The Pocahontas group, or Lower Pottsville measures, has a thickness of 750 ft. in southern McDowell County, which decreases to about 350 ft. at Prince, on the New River, in Fayette County, 50 miles to the northeast. In this group, at various points, 12 coal beds have been found, of which 4 have been found in workable thickness and are now being mined. The New River group, or Middle Pottsville measures, is just above the Pocahontas group and varies in thickness from 1300 ft. in southern McDowell County to about 700 ft. along New River. At various places, 16 beds of smokeless coal have been identified in this group, of which 5 have been found in workable thickness and are now being mined. A general columnar section of these strata is shown on Fig. 2. The workable seams in these strata, arranged in geological sequence, are as shown on page 77.

Jan 1, 1932

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.'s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By G. H. Tausch, J. R. Dublin, T. A. Huber

Simplified equipment and techniques have been developed to permit cementing a completion interval in a well and recompleting higher, lower, or at the same depth in such a manner as to: 1. Eliminate the need for a conventional drilling or workover rig. 2. Eliminate mud and other cement contaminants which have long interferred with ideal cementing. 3. Eliminate need for drilling out cement. 4. Provide a more satisfactory recompletion. 5. Provide a more economical recompletion. This technique involves the use of a small-diameter, lightweight, tubing extension which is run on a wireline and set in a landing nipple previously installed in the tubing string. Low squeeze pressure and small cement volumes, with their attendant cost reduction, are successfully used when wells are completed and reworked with salt water or other penetrating fluids. Relatively low-water-loss cement is an integral component of the technique which provides that excess cement be reverse-circulated from the well to leave the casing void of cement when recompleting lower or in the same interval. Substantial cost reductions are realized by using the simplified or low-pressure cementing technique, and the ratio of successful squeeze-cement operations has been increased. Squeeze-cementing or recementing is the act of filling a channel behind casing or filling holes purposely placed in the casing. To obtain a satisfactory squeeze-cement job, it is necessary only to fill the channel or the perforation holes with a cement filter cake and to allow it to harden in that position. In the past, the presence of mud in a well has been considered the chief deterrent to obtaining a good cement bond and satisfactory cement job; however, late developments in squeeze-cementing have made it possible to eliminate cement contamination or interference. Since it is possible to form a cement filter cake with a small pressure differential, squeeze-cementing with high pressures may not be necessary in most cases. The amount of cement needed to fill the annulus about the casing and even to fill part of the casing, if necessary, is generally small in quantity. Use of low squeeze-cementing pressures and small quantities of cement provides the following advantages: 1. Longer effective life of well tubing, casing, and other equipment; and less chance of costly equipment failure due to excessive pressure. 2. Monetary savings effected by elimination of retainers and specal squeeze-cementing tools. 3. Monetary savings effected by use of small quantities of cement and fewer squeeze-cementing operations. 4. Future surface squeeze-cementing equipment may be smaller and more economical to operate and maintain.

Jan 1, 1955

By A.E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By A. E. Martin, Gerhard Derge

IE the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of dilfusion, and electrica1 conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented us Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags oi the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. Review of Literature In 1906 Aikenl obtained a patent for a continuous process of producing iron electrolytically by passing a direct currenl through a bath of FeO.SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By D. McLean

For many pu@oses uniform strength is desired over a long temperature range, coupled to a band of softness at the hot end for easy shaping. Various types of material fulfill such a requirement to different degrees, depending on the regularity of their atomic structure. In long-chain polymers and vitreous glasses the irregular structure leads to a steep temperature dependence of deformation resistance and the temperature band between the hard and brittle condition and the soft condition is only about 100 C. In crystals and especially metals the atomically regular structure leads to a much smaller sensitivity over a wide temperature band, thus approaching the ideal behavim. The reason for this insensitivity is that the regular crystalline structure deforms by the movement of dislocations and the elastic interactions of dislocations in- PLASTICS, GLASSES, AND CRYSTALS The ease or otherwise of deformation varies with temperature much more in some substances than in others. This is an important matter when service over a wide temperature range is needed, especially volve energies of several hundred electron volts compared with which the energy of thermal agitation is insignificant. However, temperature affects a metal's defmmation resistance through its influence on the annealing, m coarsening, of the three-dimensional dislocation network. This coarsening is a phenomenon very similar to grain growth and ideas about grain growth can be applied to it. Taking into account also the temperature dependence of the glide resistance from alloying additions, a reasonable account can be given of the overall effect of temperature on deformation strength and of stress and grain size on deformation rake. Special structures me described. some arising from these ideas and as yet untried, which may benefit metals and polymers but not ni-treous glasses. when in addition a degree of softness suitable for shaping is required at some stage. It would be nice if one could write on this subject in as much detail about plastics, glasses, and so forth, as about metals, but there has been far more study of this matter in metals than in other substances, which is one reason why most of this paper concerns metals. However, in Fig. 1 there are shown the deformation strengths of several nonmetallic substances as a function of temperature. In many tests the attempt at deformation caused breakage and the graph lines are then drawn dashed. Long-chain plastics, a glass, and a crystalline substance are included in Fig. 1. The notable feature of all of them is the sensitivity of the

Jan 1, 1969

By W. F. Chiao

Ultrasonic attenuation, a, measurements in the frequency range of 5 to 55 mc per sec have been studied to determine their quantitative relationship with the following three variables of mixed microstructures in steels: 1) the volume percent, XF, of polygonal fer-rite in mixed structures of martensite and polygonal ferrite in Fe-Mo-B alloys: 2) volume percent, XA, of retained austenite plus martensite aggregates in high-carbon steel; and 3) substructural differences between 100 pct bainitic ferrite structures formed at various temperatures. The quantitative relationship obtained in the first two conditions by plotting a us the known structural parameters can be expressed, respectively, as: where al, a 2 and C1, Cz are constants. In the third condition the nature of the attenuation depends on the state of dislocations generated at the transformation temperatures and also on the alloy composition. From these measured results, the mechanism of ultrasonic attenuation caused by these mixed microstructures can also be studied. MUCH interest has recently been shown in the application of ultrasonic attenuation and wave velocity measurements to the study of the microstructural characteristics of steels. The general aims of most of the investigations in this field can be grouped into two categories: one is to study the mechanisms of ultrasonic losses caused by the characteristic phases in the microstructure of steel,''' and the other is to develop nondestructive test methods and applications for quality control.~' 4 Apparently no work has been done on the evaluation of ultrasonic attenuation meas -urements as a means of quantitative determination of a given phase in the microstructure of a steel. It is well-established that the decomposition of austenite results in four main microstructural constituents—polygonal ferrite, pearlite, bainite, and martensite—and that each phase has different mechanical properties. Thus, when a steel consists of mixed microstructures, the mechanical properties can often be related to a quantitative measure of the volume percent of each phase present. This study relates ultrasonic attenuation measurements to: 1) the volume percent of polygonal ferrite in mixtures of martensite and polygonal ferrite in Fe-Mo-B alloys; 2) the substructural differences between 100 pct bainitic ferrite structures formed at various temperatures; and 3) the vol- ume percent of austenite in austenite plus martensite aggregates in a high-carbon steel. The choice of the specimen materials was based on the laboratory stocks which were suitable to produce the required mixed microstructures for this study. EXPERIMENTAL PROCEDURES Materials and Heat Treatment. Polygonal Ferrite Plus Martensite Structures. This mixture of phases was produced in a vacuum-melted Fe-Mo-B alloy. The alloy was hammer-forged at 1900" ~ to a -f-in.-sq bar. By isothermally heat treating the alloy at 1300° F for various times and then water quenching, variations in the amount of polygonal (or proeutectoid) ferrite can be controlled in a microstructure in which the balance of the material is martensite. In the present work, four different times of isothermal transformation were adopted; after heat treatment, the four specimens were machined for ultrasonic measurements. The compositions, heat treatments, and dimensions of the four specimens are listed in Table I. 100 pct Bainite Structures Formed at Different Temperatures. It has been well-established by Irvine et al.= that the presence of molybdenum and boron in ferrous alloys can retard the formation of polygonal proeutectoid ferrite and expose the bainitic transformation bay, so that a more acicular or bainitic ferrite can be obtained over a wide range of cooling rates. Their investigation6 also showed that the mechanical properties of fully bainitic steels are usually closely dependent on the substructural characteristics of the steels. For studying the substructural characteristics in completely bainitic structures, six Fe-Ni-Mo alloys, of which five were free from carbon addition and one with 0.055 pct C addition, were selected so that a wide range of hardness values for 100 pct bainitic ferrite structures could be produced by normalizing at 1900" F followed by air cooling. The different bainitic transformation temperatures were recorded during air cooling. All of the alloys were vacuum-melted and then forged at 1900" F to square bars. Data on the six specimens of these structure series are summarized in Table 11. Austenite Plus Martensite Structures. The high-carbon steel used to study austenite plus martensite structures was vacuum-melted and then forged into Q-in.-sq bar. The series of mixed structures of austenite plus martensite was produced by quenching the specimens from the austenitizing temperature to room temperature and then refrigerating them at various temperatures within the range of martensite transformation to produce different amounts of retained austenite. Data on the four specimens of this series are listed in Table 111. Quantitative Analysis of the Microstructures. The microstructures containing martensite plus polygonal ferrite were analyzed by the point-counting technique.

Jan 1, 1969

By F. W. Jessen, H. Kazemi

A washing technique has been developed to form a spherical cavity in massive salt. The technique is, basically, a process of controlling the fluid motion in the cavity, the concentration distribution of brine, the rate of dissolution at the walls of the cavity, and the particular settings of the wash pipe, or pipes (inlet and outlet pipe) employed. For a particular arrangement of tubing and casing, fresh water enters from the casing annulus at a position above the bottom of the tubing, and the dissolved material leaves the cavity through the tubing near the bottom of the projected hole. The initial configuration of the cavity is cylindrical, representing the drilled hole situated at the axis of the projected cavity. As washing progresses the original hole is enlarged radially (any direction perpendicular to the axis of the hole). An inert fluid (generally a hydrocarbon, natural gas, or air) which serves as a blanket is injected through the annular space between the original hole and the casing. The controlled downward motion of this blanket maintains the upper edge of the brine region that is expanding on the surface of the projected sphere. A large spherical glass container and a radial model were used to investigate the flow patterns and the concentration distribution of brine occurring during the progress of solution of the salt. Aluminum flakes and dye were injected and flow patterns were observed and recorded on motion picture film. Based on the results of these model studies and other work carried out in this laboratory, the controlled washing technique was formulated. INTRODUCTION Underground cavities leached in salt beds and salt domes have been used extensively for storing hydrocarbons. Little attention has been focused on the shape of the cavities as long as large volumes were obtained and the cavities were structurally stable. The general process involves circulating fresh water and removing brine. Two distinctly different circulating systems can be employed, each of which yields characteristically different shapes. By far the most generally accepted method of washing storage caverns in salt domes is the direct circulation system. Water is introduced through the innermost pipe of a concentric pipe system, and brine is withdrawn through the annulus. In the reverse-circulation method, water enters through the annulus and is discharged through the smallesc tubing string. The size of the operation, and hence the size of tubing and casing used, depends on such factors as cavity volume, length of hole, availability of water, disposal of brine and power requirements. Underground caverns are from 100 to 1,000 ft or more in length, and when completed vary from 40 to 100 ft in diameter, providing storage of 100,000 bbl or more. The volumes of water required per volume of salt removed vary from 6 to 7 for the reverse circulation method to 10 to 11 for the direct circulation method. Up to 80,000 BWPD are often circulated. In the direct circulation method, because water enters near the bottom of the projected cavity, solution of salt is greatest at this point, particularly in view of the fact that when the washing is begun turbulent flow undoubtedly exists in the immediate vicinity of the discharge of the inlet water. As the diameter of the hole increases, flow rates also are increased, so perhaps the condition of fluid turbulence is maintained for some time. During the later stages of leaching, when capacity of equipment may be the limiting factor in maintaining flow rates, there may still exist some turbulence adjacent to the point of influx; however, for the most part laminar flow conditions prevail. There appears, therefore, rather good evidence to indicate that the state of fluid motion is responsible for the typically shaped cavity which results from such washing — namely a cylindrical form, generally somewhat larger at the bottom than at the top. Depending on the number of so-called stages which might be employed, the walls or surfaces of the salt diminish rather uniformly from bottom to

Jan 1, 1965

By H. Schwartzbart, J. R. Low

Annealed, .Poly crystalline, low carbon steel exhibits a phenomenon known as the "yield point." If such a steel is loaded in tension, the load increases steadily with elastic strain, drops suddenly, fluctuates about some constant load value for a time and then rises with further strain. The load at which the sudden drop occurs is called the "upper yield point"; the load at which deformation proceeds at constant load is known as the "lower yield point"; the amount of elongation at constant load is termed the "yield point elongation." Deformation which occurs during the yield point elongation is heterogeneous in nature, deformed metal existing next to undeformed metal. The drop in load from the upper yield point is concurrent with the formation of a band of deformed metal which usually appears at a stress concentration such as a fillet and at an angle of approximately 45" with the direction of pull. As deformation proceeds during the yield point elongation, the deformed region grows until the entire specimen has been strained an amount equal to the strain in the first band. A phenomenon very often associated with the yield point is that of strain aging. Aging in steels may be of two types: quench aging, or precipitation hardening, and strain-aging. Strain aging differs from precipitation hardening in that if the metal is merely strained instead of given a solution anneal and quenched, it then undergoes changes in properties similar to those observed in quench aging. The yield point effect and strain aging are most markedly exhibited by low carbon steel, but have been observed in other alloys. Numerous explanations for the mechanisms of both phenomena have been advanced, but the evidence for the acceptance of any of the hypotheses is incomplete. One of the explanations of the yield point phenomenon frequently proposed is that there exists a honeycomb of grain boundary material that supports the load above the yield strength of the ferrite and that when this network ruptures, the ferrite flows with no increase in load. This notion was first advanced by Dalbyl in 1913 and has been since put forward in more concrete form by many investigators. The testing of this hypothesis was, in part, the object of the present investigation. Similarly, the mechanism by which strain aging occurs remains to be explained. Presumably, it is a precipitation hardening phenomenon similar to quench aging, the precipitation being initiated by strain. However, it is not known whether the process is a solution and precipitation effect or a change in solubility due to strain. One obvious method of determining whether or not the yield point is a grain boundary phenomenon is to determine if single crystals exhibit a yield point. Low and Gensamer2 have shown that carbon and nitrogen are responsible for the yield point and aging in steel and that these effects can be eliminated by the removal of these elements through wet hydrogen purification. Single crystals that have been grown in wet hydrogen treated material must then be recarburized or re-nitrided in order to evaluate the effect of grain boundaries. In the present investigation, single crystals of iron which had been annealed in wet hydrogen to remove the carbon and nitrogen were cut into two specimens having the same orientation with respect to the tension axis. Of these, one specimen was pulled in tension in the wet hydrogen treated state and the other was carburized or nitrided and tested similarly. All the crystals were examined for a yield-point and strain aging. The grain boundary hypothesis for the explanation of the yield point in steel has been tested only indirectly previously. Arrowsmith,3 Andrew and Lee,4 Edwards and Pfeil,5 Fell,6 Ludwik and Scheu,7 Winlock and Leiter8 and others found a decrease in proportional limit and yield point effect with an in-

Jan 1, 1950

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum's data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster's4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960

By J. T. McGrath, R. C. A. Thurston

Poly crystalline specimens of copper, and copper with various additions of zinc, were tested in plane-bending fatigue. In tests performed at a constant stress, the fatigue life of copper increased slightly with the addition of up to fifteen per cent zinc. There was a sharp increase in fatigue life as further additions of zinc of up to 35 pct were made. Surface observations showed that the coarse slip bands that are characteristic of fatigue became narrower as the concentration of zinc increased. The rate of crack propagation also decreased with increasing zinc content. It is suggested that the fatigue behavior is controlled by cross slip processes. CROSS slip occurs when dislocations move from one primary slip plane to another along a connecting or cross slip plane. The primary and cross slip planes have a common slip direction. Wide stacking faults, having low energy, tend to make cross slip more difficult. According to recent theories, the ability of a material to cross slip is important to the formation and propagation of fatigue cracks. McEvily and Machlin2 have examined this concept experimentally by fatiguing single crys tals of lithium fluoride, sodium chloride, silver chloride, and KRS-5.* The latter two materials ex- hibit easy cross slip, while the former two do not. Normal rapid fatigue failure was obtained in the silver chloride and KRS-5 specimens, whereas it was much more difficult to achieve in sodium chloride and lithium fluoride crystals. Furthermore, numerous slip band extrusions and intrusions were found in silver chloride and KRS-5 crystals, whereas only one isolated extrusion was found in lithium fluoride and none was found in sodium chloride. McEvily and Machlin also consider that there is no clear-cut demarcation between crack initiation and propagation. The intrusion-extrusion process, which initiates crack formation, continues ahead of the cracks to allow propagation of these cracks along slip bands. The process of cross slip is therefore important not only to crack initiation, but also to crack propagation. Holden4 postulates that fatigue crack growth is dependent upon cross slip and thus upon stacking-fault energy. Using an X-ray microbeam technique, he found a cyclic subgrain structure in fatigued aluminum and a-iron. Holden suggests that micro-cracks develop in the densely-packed sub-boundaries ahead of the main crack front, and when sufficiently numerous join up to promote crack growth. The ease with which a subgrain structure could form would depend upon the ability of the dislocations to cross slip, and thus upon the stacking-fault energy. Hence in aluminum, which has a high stack-ing-fault energy and in which cross slip is easy, Holden found that the relative rate of fatigue crack propagation was considerably greater than in stainless steel, a low stacking-fault energy material. It has been shown by a number of investigators that the probability of forming deformation stacking faults in copper increases as zinc is added.5-7 Cross slip should, therefore, become more difficult as the zinc concentration is increased. In order to check the validity of the foregoing theories, it was decided to test copper and copper with various additions of zinc in plane bending fatigue, and determine to what extent their fatigue properties are dependent upon their ability to cross slip. EXPERIMENTAL PROCEDURE Fatigue tests were carried out on polycrystalline OFHC copper and various copper-zinc alloys with 5, 15, 20, 30, and 35 wt pct Zn. The Cu-Zn alloys were obtained commercially in sheet form. Test specimens, as shown in Fig. 1, were machined from sheet that had been reduced to an approximate grain size of 0.040 mm, the heat-treatment procedure being similar to that of Feltham anc copley.8

Jan 1, 1963

W. G. MATTESON, Houston, Tex.-I think that Mr. Powers has given us some very valuable information on the Healdton field, which is of material interest in view of the fact that the Healdton field has passed Cushing in the point of production, and if not leading, stands second only to the new El Dorado field in the point of production of the oil-in this country. Mr. Powers says that the deepest producing sand at Healdton is 1860 ft. Within the last 3 or. 4 months they have drilled to 2700 ft. there and found a sand which is producing very high-grade oil, if I remember correctly, about 42 gravity. Another very important point brought out by Mr. Powers is the fact that the Pennsylvanian beds and the Permian beds are conformable according to his interpretation. He seems to have based his interpretation upon the gathering of a number of well logs and a very careful study of them, but it seems to me the information furnished by the, well logs is really insufficient to justify such an important conclusion. In the first place, the difficulty of interpreting the line of demarcation between the Permian "Red Beds" of Oklahoma and the top of the Pennsylvanian is apparent, for the reason that sometimes the uppermost Pennsylvanian formation has a reddish phase and the line of demarcation is not very sharp.

Jan 4, 1918

By R. W. Raymond

In my paper on " End-Lines and Side-Lines in the Mining Law," read at the New York meeting of February, 1889 (Trans., xvii., 787), I discussed certain points involving the rights of a locator, B, who had located and surveyed a piece of ground, X + Y, of which only Y was properly subject to location, X being already held by another claimant, and had applied for and received a patent, granting X + Y, " excepting and excluding X." The paper concluded with the following questions : " Is there any difference in effect between the grant to him of Y simply and the grant of X + Y, ' excepting and excluding X' ? Why should any mining locator stake out his boundaries upon another location, and thus appear to assert a claim which he immediately withdraws? What is the legal force of such boundaries, established upon the land of another?" After calling attention to the fact that the entrance upon another's land for such a purpose is a trespass, and the principle that no trespasser can create by his trespass any right which he would not have without it, I reserved to another occasion a review of the history of the absurd practice of imaginary boundaries for mining claims, and a discussion of their legal effect. This practice is founded, of course, in the regulations and decisions of the United States General Land Office. There is nothing in the Revised Statutes which hints at it. On the contrary, the terms of Section 2322, giving to a locator " the exclusive right of possession and enjoyment" of the surface of his claim, seems clearly to forbid the use of that surface for the boundary-stakes of another locator. But the Act of 1866, though it provided for the issue of patents upon payment to the Government of so much per acre, and really by implication (as I have always believed) involved the absolute grant of the surface, was not so construed by the courts generally, or by the Land Office. Surveys were laid one over another in inextricable confusion, and the United States sold at $5 per acre the

Jan 1, 1890

By Roger M. Zimmerman

The G-Tunnel heated block experiment is being conducted on the Nevada Test Site (NTS) as part of the Nevada Nuclear Waste Storage Investigations project (NNWSI). The purpose of the ambient temperature testing ph se is to evaluate rock-mass mechanical properties of a block (- 8 m3) under biaxial stress changes up to 7.5 MPa above an initialization in situ value of 3.1 MPa. Results indicate that the modulus of deformation ranges from 9.7 to 17.0 GPa and Poisson's ratio ranges from 0.21 to 0.33. In general, the higher values of the modulus and Poisson' s ratio were influenced by fracture propagations parallel to the compressive stress field. Other measurements indicated that cross-hole compression (p) wave velocities and single fracture permeability values were relatively insensitive to stress changes above the in situ value.

Jan 1, 1984

By Samuel Gibson Frantz, G. W. Jarman

The purpose of this paper is to relate briefly the development of magnetic separation and its extension from the separation of iron into its present use in the nonmetallic field, to suggest possible future extensions of its field of usefulness and its possible cooperation with other separating methods. The engineering design of separating machines, and statistics as to the number of machines in operation, types, their location and production are outside the scope of this paper. Specific data will be given, however, on certain selected applications. A large part of human endeavor consists in separating one thing from another; the good from the bad, the desired from the undesired. In fact, a philosopher might plausibly claim that separating things into categories and choosing between them is the object of thought itself. In dealing with matter, separation is nowhere more inherently necessary to attain our objects than in mining and metallurgy. Both our desire and our ability to make separations are results of the physical differences between things. Gross separations such as removing ore from worthless rock or coal from slate are usually made visually and depend upon form and color, which are physical properties. When the desired and the undesired things are intimately mixed, however, it becomes impractical to select visually even if the individual particles are readily recognizable to the eye, and some automatic way of making the particles separate themselves on the basis of their own inherent differences in physical properties must be resorted to. Some of the physical properties which have been used as a basis of separation are: color, shape, hardness, size, density, elasticity, surface propertics (surface tension in contact with liquids, etc.), electrical conductivity, dielectric constant, and magnetic susceptibility. Differences in these properties are used in the following methods of separation: color sorting, sifting, settlement in air and in liquids, float-sink methods, flotation, electrostatic and magnetic separation.

Jan 1, 1932

By C. R. Garr, A. R. Troiano

FLAKING or hair-line crack formation has been a major problem confronting the producer of large alloy steel forgings.' Today it is generally conceded that hydrogen in one or more forms in alloy steel sections is a requisite for flaking. Hence an obvious remedy is a thermal cycle that reduces the hydrogen content to some low level. In practice, this generally means holding the material at some subcritical temperature for a period of time depending on the size of the ingot or forging. Another method that will suffice in some cases is to cool large forgings slowly, i.e., bury in ashes. In practice, this hydrogen bake is sometimes accemplished inadvertently by a series

Jan 1, 1958

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941