Search Documents

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By F. H. Wilson, M. L. Kronberg

The low temperature recrystalliza-tion of very heavily rolled copper produces a fine grained structure with a high degree of preferred orientation. Additional heating to within a few hundred degrees of the melting point may induce an abrupt and pronounced increase in the grain size, with the resulting crystals having new orientations. This behavior at high temperatures is commonly termed "secondary recrystallization." Several investigations have dealt with the phenomenon arid have served to bare many features of the beha~ior.1-4 In general,observations have been made on the sizes and shapes of the grains, and data have been presented showing the existence of an induction period in isothermal experiments. Although it has been well established that the orientation before the change is statistically (100) 10011, the so-called "cubically aligned" texture, there is no such agreement on the orientation after the change. For example, Dahl and Pawlek1 describe it as being equivalent to an approximately 30" rotation about the [l00] axis of the ideal cubic texture which is parallel to the rolling direction, the resulting orientation being near (210)[001]; and Cook and Richards2 find an orientation of approximately (110)[L12]. Since the completion of most of the work to be reported in this paper, Rowles and Boas3 have published their ver] illuminating paper on "secondary recrystallization," in which they present convincing evidence for a third orientation and show that their esperiments give no evidence for either of the other two orientations. The orientation is described as equivalent to an approximately 30° rotation about a [ 111] pole of the ideal cubic orientation. The existence of a variety of reported orientations is not unique for copper, for a similar state of affairs exists for other systems that have been studied— aluminum, nickel, nickel-iron alloys, and others. It seems therefore that the existence of this variety does not necessarily constitute a contradiction, but rather indicates that different experimental conditions yield different results. The fundamental nature of the phenomenon has not been elucidated. However, it has been generally recognized that the large grains could be the end product of growth of a few select grains already existing in the sample in minor amounts—too small to allow detection—or that entirely new ones could be formed by a process of nu-cleation and growth. Existing experimental evidence does not distinguish between these two most apparent possibilities. Nevertheless, the former has been more generally favored largely because our current understanding of the state of an annealed metal has not made it seem reasonable to expect a nucleation event to occur at temperatures above those required for the primary recrystallization. Observations on the Preparation and Heating of Twin-bearing Cubically Aligned Copper The starting material used throughout. the investigation was a bar of OFHC copper, forged and annealed at 950°C. Visual inspection showed the grain size to be around 0.5 mm, and did not disclose any preferred orientation. A chemical analysis showed the following composition: Cu + Ag— 99.99 Pct S — 0.005 pct 0 — <0.005 pct For the preparation of cubically aligned copper, ¾ in. thick slabs were cut from the bar, heavily pickled in concentrated HNO3 and cold rolled to sheets about 0.012 in. thick. The reduction in thickness was approximately 98.5 pct. Standardized annealing techniques were followed. Samples to be heated were lightly dusted with alumina in order to prevent sticking and then sandwiched between 1/16 in. copper plates. The resulting sandwich was heavily wrapped with copper sheet, and then annealed in air. The protection was such that only very thin films of oxide were formed. That the associated light oxidation of the samples had no specific effect on the recrystallization behavior was shown by the similar results that could be obtained on annealing in highly purified and dried hydrogen. Two methods were used in bringing samples to temperature: (1) by placing the package directly in the furnace at temperature and (2) by placing the package in the furnace at room temperature, and then slowly increasing the temperature. The corresponding heating rates are illustrated in Fig 1, and will be referred to as "rapid" and "slow," respectively. Unless specified otherwise, all anneals will be of the former type. Metallographic examination was made on samples prepared by electrolytic polishing and etching as described in the Metals Handhook.* STRUCTURES FOUND BEFORE "SECONDARY RECRYSTALLIZATION" OCCURS Annealing the rolled material for 1 hr at 400°C produced a heavily twinned, cubically aligned structure, the grain size being of the order of 0.03

Jan 1, 1950

By S.H. Ash, P.S. Miller

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By Michael Hoch, Michel Desjardins

The isothermal section of the Mo-Ti-Zr-0 system at 1500°C was investigated using X- ray diffraction and mefallographic techniques. Up to 66.7 at. pct 0, the system contains ten four -phase regions. Isopleths at 10, 30, 45, 55, and 60 at. pct 0 were constructed. THE purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of molybdenum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct o. PREVIOUS INVESTIGATIONS The Ti-Zr-0 system was investigated in this laboratory.&apos; The binary systems of interest have been compiled and discussed by Hansen&apos; and Levin, McMurdie, and Hall.3 Farrar, Stone, and Margolin studied the titanium-rich corner of the Ti-Mo-0 ternary. MATERIALS The titanium powder, 99.6 pct pure, the zirconium dioxide, and the molybdenum powder were supplied by the Fairmont Chemical Co. The zirconium powder,

Jan 1, 1962

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling&apos;s work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman&apos;s experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman&apos;s plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.&apos;. &apos; It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:&apos;. &apos; Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.&apos;. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "&apos; The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By G. R. Speich, S. A. Kulin

The isothermal formation of martensite at subzero temperatures has been studied in an austenitic stainless steel. The amount of martensite formed isothermally in a given time was found to follow a C-curve behavior with decreasing temperature. Since isothermal rnartensitic transformation occurs at temperatures above the true M. temperature of the olloy, the observed M. temperature is dependent on the cooling rate. It is believed that a general martensite theory must include the basic concepts of the strain embryo theory, and also the important role of thermal fluctuations. UNTIL recently the isothermal component of the martensitic transformation had been considered as a trivial effect in theoretical considerations of this type of transformation. One of the postulates used in defining a martensitic transformation was that the reaction was temperature dependent but not time dependent. Cohen and his associates1&apos;2 were the first to report the isothermal formation of mar-tensite. They obsel-ved the time dependency of the martensite reaction at room temperature in plain carbon steels and certain tool steels. They found that a small amount of additional transformation occurred after the specimen reached the quenching temperature and that the rate of this isothermal transformation decreased rapidly with time. These authors considered this phenomenon to be a "tailing-off" of the main athermal reaction. Kurdjumov and MaksimovaL 5 studied the isothermal formation of martensite at subatmospheric temperatures in steels containing 0.6 pct C-6 pct Mn, 1.6 pct C, and in an iron-base alloy containing 23 pct Ni and 3.4 pct Mn. In each case it was found that both the initial rate and the total amount of isothermal transformation exhibited sharp maxima with decreasing temperature. They stated that it was possible to completely suppress the martensitic transformation in the 0.6 pct C-6 pct Mn steel by drastic quenching in liquid nitrogen. They interpreted their results in terms of a thermally activated process. The maximum in the rate of nucleation vs. temperature curve was assumed to be a result of the temperature dependence of the rate of growth of the martensite plates. It has been demonstrated," however, that martensite plates can form with great rapidity even at temperatures approaching absolute zero. In addition," attempts to confirm the reported suppression of the martensitic transformation by rapid cooling of a 0.6 pct C-6 pct Mn steel have proved unsuccessful. On this basis, and on other theoretical grounds, the validity of some of Kurd-jumov&apos;s results and conclusions is open to serious question. Cohen, Machlin, and Paranjpe&apos; have proposed a theory of martensite formation based on the nucleation of strain embryos and a growth mechanism involving cooperative atomic displacements. According to this theory thermal fluctuations can make a strain embryo supercritical and thereby produce martensite isothermally. Das Gupta and Lement&apos; have investigated the isothermal formation of martensite in a 17 pct Cr-0.7 pct C steel at temperatures below the ambient. They found that partial suppression of the martensitic reaction occurred on quenching into liquid nitrogen. That part of the reaction which can be suppressed is taken to correspond to the isothermal rather than the athermal part of the rnartensitic transformation. The initial rate of isothermal transformation for this steel was found to go through a maximum with decreasing temperature. This is in conformity with the findings of Kurdjumov and Maksimova for the steels used in their investigation. Das Gupta and Lement conclude that isothermal martensite formation occurs by the nucleation of new plates and is always preceded by some athermal transformation. An iron-base alloy containing 14 pct Cr-9 pct Ni was used in this investigation to study further the kinetics of the austenite to martensite transforma-

Jan 1, 1953

By A. G. Metcalfe

THE failure to detect any change in the thermal properties of cobalt at the Curie point would appear to indicate that the apparatus may have a limited sensitivity. The Curie temperature has been determined by direct methods to be 1121+3°CP and 1131°C.3 The specific heat has been determined many times&apos;.&apos; and weighted values are given in Table I. The allotropic transformations in iron and titanium, used by the authors to test the experiment method, involved a volume change of the order of 3 pct on going from the close-packed to the body-centered-cubic lattice. These energy changes are likely to be much larger than those involved in a diffusionless transformation from a hexagonal to a cubic-close-packed lattice. However, it has been pointed out that thermal observations are unreliable in the detection of phase changes when these are near a Curie point.&apos; James 0. McCaldin and Pol Duwez (authors&apos; reply)—The sensitivity of the present technique is limited to first-order transformations, so that gradual changes in specific heat, e.g., in the vicinity of Curie points, are not detected. Furthermore, the existence of first-order transformations with latent heats much smaller than those occurring in the known allotropic transformations of iron and titanium is, we agree, still pending.

Jan 1, 1956

By R. C. Hepworth

Heaving in roads built on the Mancos Shale is a serious problem in east-central Utah. Heaves are expressed as local bumps, general rises and severe cracking of the pavement. The heaves usually occur in shale road cuts and generally show a seasonal cycle, which reaches a maximum development in the winter. The presence of certain salts, absorption of moisture and physical properties of the subgrade materials were considered, in Utah, to be the main factors in the heaving mechanism. Work done on similar problems elsewhere and studies conducted by the author indicate that the latter two factors are the most important. Results of this investigation indicate that heaving areas are associated with slaking shale or expansive clays, with and without salts present. Laboratory studies show that the initial moisture content of remolded samples and the desiccation history of un- disturbed samples have a major effect on swelling. Swell tests on compacted samples at various temperatures indicate that water has more influence on swell than temperature, except for samples containing sodium sulphate, which swelled with decreasing temperature. Chloride salts inhibited swelling. Tests on shale cores indicate that the stability of slaking shale can be preserved by maintaining its original moisture content. It is concluded that shales and expansive clays, when exposed in road cuts, become desiccated and are subject to expansion when moisture is subsequently available. The seasonal cycle of heaving may possibly be explained by the annual moisture excess and deficiency. To minimize the problem, freshly exposed shale should be kept wet, and the thickness of the subbase and base courses should be increased. The Utah State Department of Highways has been plagued for many years with a distressed condition that develops in roads constructed on the Mancos Shale. Locally these distressed areas are known as heaves, frost boils and alkali boils. These names refer to the surface expression, time of year

Jan 1, 1965

By David Browne

THE literature dealing with the physical constants of nickel is so fragmentary and unrelated, that a synopsis presents unusual difficulties. It is only within the last few years that investigators have understood the importance of placing on record not only the determinations they have made but also the composition, physical treatment, and past history of the material investigated. For this reason much of the earlier literature is valueless. Determinations have been made of the same physical constants on samples differing widely in origin, composition, and treatment, and the results differ widely among themselves. In the first place nickel is almost as flexible a term as steel. Its physical properties are widely influenced by its composition and treatment. It absorbs large quantities of gases and is exceedingly difficult to prepare in a state of chemical purity comparable to gold, silver, or copper. It is vitally affected by thermal and mechanical treatment. Hence in the following pages the recorded literature, where quoted, must be accepted with a certain reserve and used, as far as possible, as a check on later observations, in which these important factors are noted. In every case where new determinations are given, an attempt has been made to record all available information concerning the composition and treatment of the material used so that the data may serve as steppingstones toward a wider knowledge of the properties of the metal. As this synopsis is an attempt by men of metallurgical training to do what should long before have been clone by physicists, it is to be expected

Jan 9, 1919

By Clinton M. Young

The experiments herein described were carried on in 1908-9 by- the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coalmines, a subject which is engaging the attention of numerous investigators. An unusual number of serious disasters has directed to the subject a study which discloses the disquieting fact that, in the United States, the ratio of lives lost per ton of coal mined has been 011 the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and a very great increase in the amount of explosive used. This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle West it is not now uncommon for a miner to use six kegs (150 lb.) of black powder in a " pay" of two weeks, while within the memory of men still active, one keg (25 Ib.) would last two men for a " pay." So great has the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject of explosions in coalmines has led to the belief that the use of large quantities of explosives, in some cases by slightly-trained men, had riot been

Jan 1, 1911

By W. Robert Power

Dimension stone is considered by many the premium material for beauty and durability in institutional and monumental construction. Nonetheless in the United States it commands an ever decreasing share of the total market. At the beginning of the century dimension stone accounted for more than half the stone produced in the United States, but by 1974 it accounted for little more than 0.2% and the number of producing quarries and finishing plants had greatly reduced. This decrease in use is accounted for in part by competition from cheaper materials, but another factor seems to be the demand by many designers for uniformity and exact repetition of modular units in construction. Even where stone is used in large buildings modem architects want blandness of pattern and uniformity of color in the stone. Because most natural stone contains variations in color and pattern great strain is put on the quarriers to overcome this and produce a uniform product. This results in increased costs, increased waste at the quarries, and consequently increased price in the market. In spite of this, stone is still looked on as the most prestigious of building materials and its aesthetic appeal is born out by the many simulated stone patterns found in synthetic materials. End Use and Specifications The principal uses of dimension stone are in building construction and monuments. Other uses include flagging, curbing, paving, mill-stock slate, roofing slate, laboratory furniture, and refractory brick. Because many of these uses overlap, an orderly classification of dimension stone uses is most difficult. Various classifications have been used by Cumer (1960), Barton (1968), the U.S. Bureau of Mines yearbooks, and the Building Stone Institute (Anon., 1972).

Jan 1, 1975

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By H. M. Chance

Adequate treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed " intrinsic value " must be limited to materials that are essential to existence—air, water, food. But " intriusic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable. Possibly for present purposes the value of any material may be considered as having a dual origin: First, that due to economic

Jan 1, 1914

By J. A. Jr. Church

I. EARLY FURNACES. . COPPER blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18, ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By J. A. Jr. Church

I. EARLY FURNACES. COPPER blast-furnace construction in America has long recognized a general standard in the rectangular mater jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few mouths by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By P. Nyul, S. Caplan, M. F. Lamorte, T. Gonda

Therrnal resistance is measured on GaAs laser diodes in the temperature range 77" to 300°K. These data show that typically the thermal resistance increases fifteen times from 77 to 300°K. The increase is attributed to the decrease in thermal conductivity of Gds. Nornzalized thermal-resistance experimental and calculated from published thermal-conductivity data) values are compared and good agreement shown. In many practical applications, it is desirable to obtain high average power output from laser diodes. Average power output is determined in large measure by the external efficiency and thermal resistance of the diode.&apos;-3 The average input power with which a laser diode may be pumped is dependent on the thermal resistance. Thermal resistance has been studied over the temperature range from 77" to 300°K which is usually of interest in practical applications. This correspondence presents data on thermal resistance for GaAs laser diodes and compares them to values calculated from thermal-conductivity data. Junction heating arises from three distinct components: 1) joule heating, 2) nonradiative recombinations, and 3) reabsorption of radiation. In high-threshold lasers, joule heating predominates.4 Typically, the nonradiative recombination is not negligible and contributes significantly to junction heating. The loss caused by reabsorption may be of the order of the joule-heating loss.&apos; The fabrication and the geometry of laser diodes have been described in other publications.5 The data presented were obtained from diodes which were fabricated from the same region of a wafer to minimize differences. Fig. 1 shows four types of heat sinks employed in this study. In types 1 and 2, the laser cavities are alloyed; pressure contacts are employed in types 3 and 4, and indium is plated on the inside faces to improve the intimacy of contact between the diode and the heat sink. The thermal resistance R is defined by the following relationship: where AT is the junction-temperature rise above the heat-sink temperature for the diode power dissipation Pd. For measurement of thermal resistance, a direct current is passed through the junction, in the range from 1 to 50 pct of threshold. The diode is placed in the laser mode by superimposing a current pulse of low-duty cycle on the direct current.3 Junction-temperature rise is obtained from the time-resolved laser spectrum at the leading edge of the current pulse.&apos; Typically, the laser line shift is 2.5A per OK. The resolution employed in these experiments is 0.5A; therefore, the accuracy in the temperature measurement is 0.2K. Typically, the temperature rise is 2" to 20°K. The power dissipation is the difference between the dc power input, and the radiation power exiting the diode. The measurement accuracy is less than 1

Jan 1, 1968

By N. J. Grant, K. M. Zwilsky

A series of copper-alumina dispersion strengthened alloys were prepared using three different copper and two different alumina powder sizes. Improvements in strength of up to ten times that of pure copper were found in room-temperature as well as elevated-temperature stress-rupture tests. Conductivity values remained from 70 to 90 pct that of pure copper. The best alloys were based on the finest metal powder (1 p) and contained from 7.5 to 10-0 vol pet of 0.018 or 0,033 p alumina. DISPERSION strengthening of metals consists of strengthening a metal matrix by the addition of oxides or other refractory constituents, followed by strain hardening, in order to reinforce the base material and extend its temperature range of application. Since the discovery of SAP by lrmannl and Von zeerleder2 in 1949, many investigators have reported data obtained on a variety of metal-inert oxide alloys.3-7 The present work deals with the mechanical mixing of copper and alumina powders. While several techniques of introducing the second phase have been investigated to date, mechanical mixing so far has been recognized as the simplest, least expensive, and most universally applicable technique that can be used to obtain an ultrafine dispersion of inert particles. In the present case, the effects of changing the metal particle size, the oxide particle size and the volume percent of oxide were investigated. This work is an extension of a previous study.6 EXPERIMENTAL PROCEDURE The starting materials were three different grades of copper powder and two different alumina powders. The three metallic powders were -74 µ(- 200 mesh) electrolytic copper powder consisting of irregular equiaxed particles having a normal screen distribution and analyzing 99.5 pct Cu, and two powders having a 5-µ and 1-µ particle size, average, respectively. The latter powders were produced by the hydrogen reduction of purified sulfate solutions at elevated temperature and pressure and were furnished by the Sherritt Gordon Mines, Ltd. The alumina used was obtained from Godfrey L. Cabot Co., under the trade name of Alon C, one batch of powder having a particle size of 0.018 µ, the other a particle size of 0.033 µ. The crystal structure of these alumina powders was found to be cubic gamma. Each batch of powder was mixed in a Waring Blendor for a total of 15 min, followed by a low-temperature reduction in hydrogen and vacuum compacting in cylinders which were hydrostatically pressed at 35,000 psi to give a compact that could be handled conveniently. Six of the compacts were hydrogen sintered at 900°C while the remaining four were sintered at 1000°C. Subsequently, all compacts were hot extruded at 760°C with a reduction of area ratio of approximately 20 to 1. Evaluation of alloys included density and resistivity measurements, room-temperature tensile tests, stress-rupture tests at 450°C plus one other temperature per alloy, hardness tests, microstruc-tural examination, X-ray analysis of the dispersed phase after dissolving the metal phase, and oxidation studies on two of the alloys. A vacuum-melted, wrought copper rod was tested together with these alloys for comparison purposes. RESULTS Table I is a summary of the compositions, sintering temperatures, densities and conductivity values of the ten alloys prepared. All alumina additions are given in volume percent, and will be referred to as

Jan 1, 1962