Search Documents

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.'-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann's constant, and the vacancy formation entropy, respectively. After applying Stirling's approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling's approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling's approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By J. W. Putman, N. J. Grant, D. S. Bloom

SEVERAL recent determinations of the melting S point of pure chromium have been reported which give values of 1845°C1; 1895°C,² 1930°C,³ 1860°C,' and 1890°C.5 because of this wide spread of values, it appeared desirable to make one additional attempt to obtain a more accurate, reliable figure. bloom and Grantx recently reported a phase transformation in chromium:.--- it was desired to check this, too, in the course of checking the melting point. To accomplish this, a much higher purity chromium was required. Electrolytic chromium containing about 0.5 pct 0 was crushed to a finer size and was then annealed in highly purified, dried hydrogen at 1375°C for 100 hr. This treatment produced chromium with about 0.008 pct 0, 0.002 pct N, and negligible carbon. The balance of the impurities was 0.3 pct Fe, 0.03 pct Si, 0.004 pct S, and less than 0.001 pct Mo. This chromium was melted in a stabilized zirconia crucible under pre-purified argon, using induction heating. Temperature measurements were made with annealed wolfram-molybdenum thermocouples and a Leeds and Northrup Speedomax Recording Potentiometer. The thermocouples were annealed for 1 min in hydrogen at a temperature of about 2400°C. Each leg of the thermocouple was immersed in an ice-water mixture using mechanical connectors to the lead wires. The thermocouple tip was immersed in the molten chromium in a zirconia protection tube which introduces an error of about 3°C as a temperature drop through the walls of the tube. The weight of chromium was about 183 g. The dimensions of the melt in the crucible were about 1.25 in. diam x 2 in. high. The tip of the thermocouple was held about ½ in. from the bottom of the crucible. Two new thermocouples were used with the above set-up giving the results shown in Table I. Since this chromium is purer than that used by Greenaway, Johnstone and McQuillan,' by Carlile et al.,4 and other investigators,²,3 it is believed to be the more accurate. Thermocouple aging effects which are believed responsible for the high value of 1930°C³ were avoided in this work. This value of 1903°C is correct to about ±10°C. The right hand column lists the temperature of the a ? ß transformation on heating and the ß ? a on cooling.3 A sample curve is shown in Fig. 1. The value so determined is 1840°C + 15°C. Fig. 1 gives adequate evidence that there is a transformation in chromium at high temperatures.' References 'H. T. Greenaway, S. T. M. Johnstone, and M. K. McQuillan: High Temperature Thermal Analysis USing the Tungsten-Molybdenum Thermocouple. Journal Inst. Metals (November 1951) 19, p. 109. ²J. W. Putman, R. D. Potter, and N. J. Grant: The Ternary System Chromium-Molybdenum-Iron. Trans. A.S.M. (1951) 43, p. 824. ³D. S. Bloom and N. J. Grant: Chromium-Nickel Phase Diagram. Trans. AIME (1951) 191, p. 1009; Journal of Metals (November 1951). ' S. J. Carlile, J. W. Christian, and W. Hume-Rothery: The Equilibrium Diagram of the System Chromium-Manganese. Journal Inst. Metals (1949) 76, p. 169. 5G. Grube and R. Knabe: Ztsch. Elektrochemie (1936) 42, p. 793.

Jan 1, 1953

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By A. L. Blomfield, M. J. Trott

ThE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulfo-tellurides, with practically no base metals such as Pb, CU, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. Classification of ORes For efficiency, it has been found advisable to separate the ores into two classes according to their lime content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the lime, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A a B Insol.......................... 86.70 75.90 Al2O3........................:.. 2.30 3.40 Fe.............................. 3.26 3.48 CaO............................. 1.57 5.12 S............................... 1.79 1.80 MgO........................... 0.21 1.08 Ignition loss..................... 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 per cent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 1, 1919

By F. C. Schora, H. P. Meissner

Iron ore from Cerro Bolivar, Segre', and Sierre Grande was reduced in fluid beds at about SOOT, using gas analyzing 20.5 pct CO, 41 pct Hz, and 38.5 pct N2. Except in the early stages of reduction, the rate of oxygen loss from the bed was directly proportional to the oxygen concentration in the bed, independent of gas composition as long as the gas was reducing, and little affected by temperature. The percentage reduction of the bed solids at any time was independent of particle size. I HE reduction of spheres or cubes of dense iron ore in a slowly moving stream of either pure H, or pure CO has been found to take place at distinct interfaces between well defined layers of iron and the iron oxides.'y4 These interfaces generally penetrate the ore lump in topochemical fashion, remaining parallel to the original contours of the specimen. Thus in the earlier stages of reducing hematite, the specimen's core is Fe,O, surrounded by successive shells of the lower oxides, and finally by an exterior shell of iron. McKewan5 assumed that the rate limiting step occurred at the Fe-FeO interface, with reducing gas penetrating up to this interface through the external porous iron shell, and reduction of the higher oxides within the ore lump occurring by diffusion of iron through the dense FeO shell. He developed an analytical expression based on this model relating the amount of oxygen removed from

Jan 1, 1962

By J. B. Bassett, E. S. Rowland

INTRODUCTION THE experimental work reported herein was inspired by the publication of a paper by Grange and Stewart,1 in which it was suggested that at low chromium contents the effect of this element on the [M,] point was greater than at higher chromium contents. It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the [M,] point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature. Such enrichment of the austenite in chromium content would lower the [ M,] point nearer room temperature where cracking is more likely to occur. Accordingly, it was decided to investigate the effect of chromium, in quantities between o and 2 pct, on the[ M,] point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the [M, ] temperature values were corrected by means of the Grange and Stewart formula§ to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (2) Hypereutectoid compositions: 1.00 pct carbon and 0.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased errors such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question of the effect of chromium on the [M,] point, particularly at low chromium contents. While it is fairly well established that chromium causes the [M,] to be lowered when present in quantities of I pct or more, Grange and Stewart1 have suggested that in small amounts (less than I. pct) it is more effective in lowering the[ M,] point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the []M,] point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the-[M,] point of a 0.20 carbon steel. MATERIAL Two series of 35 lb induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0.25 pct increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1948

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By H. M. Kraner, R. C. Devries, K. H. Gee, E. F. Osborn

On the basis of liquidus measurements in the system COO-Mg0-Al2O3-Sio, and previously published data, diagrams have been constructed at 5 pct Al2O3, intervals from 5 to 35 pct Al2O3,. Liquidus temperatures and primary phase fields are shown. The optimum composition of a blast furnace slag for a given alumina content is indicated. At the optimum point, ordinary slags will be entirely liquid and will have maximum desulphurization potential and minimum viscosity. The relation of optimum composition of slags to the "plateau region" of the liquidus surface, and the application of these data on synthetic quaternary slags to actual slag compositions are discussed. Index of refraction of glasses is given as well as composition, temperature, and phase data for each mixture. THE usual blast furnace slag, as a first approximation, can be considered a mixture of the four oxides, CaO, MgO, Also,, and SiO,. Systematic, extensive data for the quaternary system, CaO-MgO-A1,0,-SiO, is therefore required for the understanding of the properties of such a slag as a function of composition and temperature. With sufficient data, it should be possible to fix unequivocably the relative amounts of lime, magnesia, and silica required for a given alumina content to result in a slag composition having optimum properties. Other constituents, such as FeO, MnO, Ti02, and S, have an effect on the properties of a slag, but as long as they are present in small and approximately constant amounts they produce only a second-order effect superimposed upon the major changes in properties of slags determined by the relative amounts of the four major components. Viscosity and desulphurization data have been reported for mixtures approaching blast furnace slags in composition, but systematic liquidus data have not been obtained. Inasmuch as a slag must be all liquid in order to be most effective as well as practicable, clearly the temperature above which a mixture is all liquid (liquidus temperature) is a type of data needed. Such data have been obtained through the study of 446 compositions and are pre- sented in this paper along with a discussion of their bearing on the optimum composition of blast furnace slags. For an orderly presentation of the data, the quaternary system is viewed as a tetrahedron with one component at each apex. Fig. 1 shows a tetrahedron representing the system Ca0-Mg0-A1,0,-Si0,. The base is the ternary system Ca0-Mg0-SiO,, A1,0, is the top apex, and the front face, the system CaO-

Jan 1, 1955

By R. S. Shoemaker, F. W. McQuiston

BENGUET EXPLORATION, Inc. Tuba, Benguet, Philippines 1970 Operating Data ORE DESCRIPTION: Complex ore mostly sulfides and composed mainly of sphalerite and pyrite with minor amounts of chalcopyrite, galena, arsenopyrite, hematite, magnetite, chlorite, calcite, garnet and quartz. TYPE OF MINE: Underground, cut and fill method ORE HAULAGE TO MILL: Mine rail cars with electric locomotives. CAPACITY in TONS/24 HRS: 130 ASSAYS: Mill Heads Mill Tails Au = 0.65 oz per ton Au = 0.096 oz per ton Cu = 0.75% CU = 0.27 % Zn = 10.50 % Zn = 0.64 % Ag = 3.20 oz per ton Ag = 0.33 oz per ton Cd = 0.01 % PRODUCT: Au, Ag, Cu, Zn and Cd RECOVERIES: = 90% ~g = 89% Cu = 60% Zn = 94% SCREEN ANALYSIS OF MILL FEED: 90% -200 mesh POWER: Grinding 25.4 Kwh/T Copper Flotation 14.5 Zinc Flotation 13.3 Cyanidation 20.4 Others 25.0 TOTAL POWER: 98.6 KwH/T WATER: Pumped from riverside and underground 50 to 100 meters distance. Consumption of about 700 gallons per ton of new water.

Jan 1, 1975

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-''FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By Albert F. Schneider

The peculiar conditions under which lead and silver ores are now smelted in Salt Lake Valley, Utah, render it advantageous to make slags that are siliceous and carry a high percentage of lime. The ores treated come from Utah, Idaho, Montana, and Nevada; nine-tenths coming from Utah. These ores are siliceous, and contain but little fluxing material; the iron present scarcely sufficing for the sulphur and arsenic. Formerly ores high in iron were furnished from Cottonwood Canons, but this supply is meagre. The ores from Idaho, Montana, and Nevada are high grade galenas, more or less impure. They generally require a large amount of iron for the sulphur, arsenic, and antimony. In the winter and spring of 1880—'81, we were treating at the Germania Works principally Bingham Canon lead ores and silver ores from Tintic. The former contained 15 to 30 per cent. silica, and only 4 to 5 per cent. iron (generally as iron pyrites); they ranged high in lead and low in silver, and carried more or less alumina; the lead was present chiefly as carbonate. The silver ores from Tintic contained sulphides, and ran as high as 80 per cent. silica. We had been running on a slag approximating 40 per cent. FeO, 20 per cent. CaO, 10 per cent. other bases, and 30 per cent. SiO2, which had heretofore been very satisfactory; but with the class of ores then coming in it was of the utmost advantage to use less iron and more lime, especially as the iron ore (50-55 per cent. iron and 5-7 per cent. silica) cost four times as much as the limestone (50-55 per cent. lime, 3-5 per cent. silica). The large amount of alumina in the slag influenced them for the worse; the addition of lime to the charge helped them, and after many experiments regarding the proportion of FeO, CaO, and SiO2, a slag approximating 35 per cent. FeO, 25 per cent. CaO, 5 per cent. other bases, and 35 per cent. SiO2 seemed to answer

Jan 1, 1883

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By S. E. Hasko

It is the purpose of this note to report the crystal-lographic data for nine new B5A compounds* having the Cu5Ca structure, with A a rare earth and B a transition element, Co, Ni or Cu. In previous papers, some magnetic data1 and preparation and crystallo-graphic data2 for other B5A compounds having the same structure have been reported. Crystallographic data for these compounds are shown in Tables I and 11. These results are in agreement with others of this series reported previously by Wernick and ~eller.' The abnormally large atomic volume of Yb metal3 is not manifested in Ni,Yb, when one compares it with the compounds reported here and the data of reference 2. This is not true for the compound YbAl,, having the cubic Laves structure (MgCuz), to be discussed in other papers.4'5 Thus, it appears that Yb has a valence of 3; i.e., the 2 s and Id electrons are lost to the conduction band.4'5 Lattice constants for four of these compounds prepared by levitation melting have been reported by Nassau, Cherry, and wallace.' The lattice constants

Jan 1, 1961

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

Lieut. Louis J. Brunel, now in France, was commissioned on July 27, 1917, as Second Lieutenant in the Engineers Reserve Corps, assigned to the 7th U. S. Engineers, Dec. 10, 1917, and has been with the American E. F. since Mar. 26, 1918. He was assigned to the staff of the General commanding the 5th Field Artillery Brigade, as Engineer Officer, on Aug. 6, 1918. E. Ross Housholder writes that "the record for pontoon bridge building was broken Sept. 25, 1918, by Section A, Co. 4, 5th Engineer Officers' Training School, at Camp Humphreys, Va., of which I am a member. The time was 15 min. 11 3/5 seconds. We then proceeded to break the record for dismantling in 9 min. 57 1/5 seconds. The length of the bridge section was 200 ft. The post band was sent out to meet us, and we feel proud of this record. I have met quite a few A. I. M. E.

Jan 11, 1918