Search Documents

By Frank Firmstone

In 1871, two furnaces at the Glendon Iron Works, which had been blown out on account of the "coal strike," were altered from the open-top plan with side flues for collecting the gas, to closed tops with cup and cone. In one furnace the suppression of the side flues permitted a considerable alteration in the profile, but in the other (No. 5) no change in this respect was made; the side flues were simply bricked up and new ones cut through the sides close to the top. This furnace was in blast over four years, and we can, therefore, form a pretty good idea of the effect of the alterations on the furnace process. The principal dimensions are; Height 72'; greatest diameter, 18'; diameter at tuyeres, 8'; diameter of top, 10'; diameter at stock line (point at which the top of the materials is kept), 11'; cubic contents, 11,900 cubic feet. The table below shows the average results for periods of twentysix weeks each. 1st, of the open-topped furnace; 2d, of the furnace with the first charger used, which was an ordinary cup and cone (diameter of cone 5' 2") 3d, with the charger used ever since, a " double " cone 7' 5" diameter outside, having a central opening 3' in diameter. The diagram (Plate 11) shows the daily variations, in the grade of the irons for the same periods.*

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.'-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.'- '' It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968

By James Boyd

Scientists and engineers must concern themselves not only with technical problems, but with the socio-economic difficulties of our scciety. The author states that raw materials are basic to the economic process and that mineral raw materials occur naturally in nearly limitless quantities. He feels that the economic pocess will provide sufficient raw materials for man's needs, and discusses in some detail the world economic environment. As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experiences to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. RAW MATERIALS BASIC TO THE ECONOMIC PROCESS There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as "All productivity is based on three factors: 1) natural resources, whose form, place, and condition are changed by the expenditure of 2) human energy (both muscular and mental), with the aid of 3) tools.77* It seems strange that such an obvious statement needs to be made. It is forgotten by all of us, however, at one time or another when we get involved in the complicated theories of economics dealing with the financial and fiscal policies of the various governments, in the financing of enterprises, in marketing, and in labor relations. Unless decisions in all of these fields are made with this, and the rest of the "Ten Pillars of Economic Wisdom," consciously in mind, the resultant policies are doomed to eventual failure, whether these are policies of individuals, companies, or governments. The economic process is basic to society. But economics and the social aspects of humanity are inevitably intertwined. If human needs are not provided for within the basic economic structure, conflicts arise to disrupt the most carefully laid social plans. Similarly, it is the failure of society to cope with basic economic prerequisites that leads to discord within the body politic and thus to eventual economic disaster. We who are engaged in the various aspects of the mineral industry, therefore, have a large part to play in society's future development. MINERAL RAW MATERIALS OCCUR NATURALLY IN NEARLY LIMITLESS QUANTITIES Throughout my career in and out of government, I have formed my decisions on two principles: 1) Fundamentally, all mineral raw materials exist within the earth's crust in quantities greatly exceeding man's needs; 2) Any problems of supply of these materials are primarily economic in nature. With respect to my first assumption, analyses by geochemists enable them to estimate the quantities in which each of the known elements exist in the earth's crust. One of the most cautious and famous suggests that the average copper content of the lithosphere to a depth of ten miles is about 55 ppm. If this is valid, then the lithosphere contains about 1.4 quadrillion (1.4 x 10 ") tons of copper metal — an unimaginable quantity. This is 8,500,000-fold that which has been consumed by man in his existence. To illustrate further, consider that the deepest copper mine in history went to about 9000 ft below the surface; the present copper mines of the world now average less than 1500 ft in depth. We can assume that in most continental land areas of the world it is technically feasible to mine to a depth of at least one mile. The land areas of the world to an average depth of one mile, then, contain 343 billion tons (343 x 10') of copper metal, or 2000 times that which has been extracted to date. I don't believe man will ever expend his energies to extract copper from rocks which contain only a few parts per million, but he knows that each element

Jan 1, 1968

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division J C Kinnear, Jr, President A W Thornton, Past President W R Hibbard, Jr, Vice-President R W Shearman, Secretary-Treasurer AIME, 29 West 39th Street New York 18, N Y Board of Directors J B Austin, D L Clark, H B Emerick, T D Jones, H H Kellogg, C T Marshall, E E Schumacher, C S Smith, J D Sullivan

Jan 1, 1957

By Lo-Ching Chang, Kenneth M. Goldman

INTRODUCTION THE kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was simple. A graphite crucible 1 5/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an induction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature [ ] for 3-5 min., after which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 min. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the temperature of the furnace in 1 to 1 1/ 2 min. Slag

Jan 1, 1948

Jan 1, 1968

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By R. M. Rose, D. P. Ferriss, J. Wulff

The effect of orientation on the stresses, nctivation energies, and activation volumes for yielding and plastic flow of tungsten single crystals was investigated. Tensile tests showed the proportional limit to be a function of orientation: crystals whose tensile axes were near the [I10} direction were roughly three times as strong as [loo] crystals. The [ 1101 crystals showed low strain hardening and displayed yield phenomena, whereas the other orientations yielded smoothly and showed considerable strain hardening. The fracture mode was cleavage, except for crystals near the [1101 , many of which gave "chisel" fractures at 300°and 373°K. The activation energy for yielding was approximately one- half an electron; volt at all orientations, and the volume of activation was (12 to 14)b3, except near the [1101, where it was 7b3. Activation volumes generally increased after yielding. The most common theoretical models for yielding and strain hardening of bcc metals were. found to be insufficient to the intepretation of the observations here in. An explanation is proposed, based on the dislocation reaction dislocation networks and jogs, md jogs formed during plus tic flow. PRECLSE knowledge of the Drocesses involved in the yielding and plastic flow of the refractory metals is essential to the formulation of models for their flow and fracture. Despite this need, the single -crystal investigations, especially of tungsten, have been sparse. Slip occurs at low temperature, according to schadler,i in <111> directions on {110) planes; as the temperature rises to room tempera-

Jan 1, 1962

By F. J. Smit, S. C. Sun

Flotation variables were investigated for the re-clamation of phosphate from a Florida washer slime. Under optimum conditions, 92% of the phosphate was recovered. Further cleaning of the rougher flotation concentrate resulted in a product containing about 30% P2O5 with a phosphate recovery of 65%. The enormous amount of slimes rejected in the Florida pebble phosphate fields, containing roughly one-third of the phosphate in the pebble matrix,1 has long been considered as a serious problem to the industry. The mere disposal of these slimes has posed an almost insurmountable task for several investigators.2-5 Some companies still resort to huge surface dams, some covering 1800 acres, for slime disposal.6 Information on the recovery of fine phosphate from these slimes is scanty. Dry separation8 and electrostatic beneficiation8 were suggested, but would necessitate radical changes in the present mining and concentration methods. Haseman10 proposed the selective flocculation of colloidal phosphate with starch, while Ralston11 suggested the removal of clay from the matrix by amine flotation. Leaching of the slimes for recovering the small amount of uranium was attempted by the Battelle Memorial Institute12,13 but proved to be economically unfeasible. The purpose of the present investigation was to determine the optimum fatty-acid flotation conditions for reclaiming the phosphate discarded with the Bartow washer slime. Prior to the flotation experimerits, however, the size distribution and the minera-logical composition of the employed slime had to be determined.

Jan 1, 1963

In preparation for the 119th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS Chairman. NY. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP Committee on Patriotic Meeting H. C. PARMELEE, Chairman.

Jan 11, 1918

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely&apos; that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:&apos; the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.&apos; The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

By Alden Greninger

TWINNED metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the obser vation of the twins, there are two other possible groups: (1) solidification twins,? when observed in the as-solidified or as-cast condition, and (2) transformation twins, ? when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form {112}. Since McKeehan&apos;s discovery, little or no attention has-been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the prepara-tion of single crystals. McKeehan&apos;s twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures-at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O&apos;Neill3. has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually

Jan 1, 1936

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. Dickson, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. H. C. PARMELEE. FOREST RUTHERFORD. P. G. SPILSBURY. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 8, 1918

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. Dickson, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. P. G. SPILSBURY. H. C. PARMELEE. FOREST RUTHERFORD. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE. FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 10, 1918

C. Q. PAYNE, New York, N. Y. (written discussion*).-The method adopted by Mr. Lennox is a very interesting test of the practical application of Mr. Gates&apos; crushing-surface diagram to a greet variety of gold and copper ores. His method of dealing with the material below 200-mesh is also a distinct contribution to the subject, although, as he suggests, it seems likely that some microscopic measurement of this material may be advisable before the mesh reciprocals of its group particles can be dealt with as accurately as can those coarser than 200-mesh. In examining the general results shown in Table 3, it is somewhat puzzling to perceive why Calumet &, Hecla jig tails should show a crushing resistance 3 - times greater than that of the ore from the Ray Consolidated copper mine. The latter is, I believe, an altered. Pinal schist

Jan 10, 1918

By Felix G. Berra, David H. Orr

The first large scale application of radio remote control equipment to standard gage railroad trains has been achieved at the Morenci mine of Phelps Dodge Corp. at Morenci, Ariz. Twenty or more ore and waste haulage trains are remote control operated at any one time, each with a one-man crew. Reduction of train crews from two men to one man has materially lowered the total cost of train operation. Elimination of brakemen has also resulted in an improvement in train efficiency brought about by a shortening of train haulage cycle times.

Jan 4, 1965

By W. G. Lidman, H. J. Hamjian

&apos; I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:&apos; the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F&apos;) at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.&apos; Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By D. W. Mitchell

J. H. Schlobohm (Joy Manufacturing Co., New York) —This paper has been read with a good deal of interest; however, there are several salient features which Mr. Mitchell has overlooked. The initial emphasis on selection should be placed on type of material to be loaded and method of mining involved. There is no possible connection in the comparison of scraper or Joy Lohite loaders with loaders of any other type. Neither can an operating comparison be made between "Rocker type" loaders and those equipped with loading head and gathering arms. Each unit has its application, but the application depends on material and the mining system involved. Mr. Mitchell&apos;s compilation of data on various loaders, while it represents a great many facts, does not represent true operational data, i.e. Table I, column heading "Max. Rated Capacity for 7 hr;" these figures are meaningless inasmuch as little or no time at all is allowed for tramming or switching or moving the loader from place to place. Table I, column heading, "Best Reported Field Shift," would be a better source of operational data, assuming of course that conditions, applicable to each class of loaders, were average to avoid enthusiastic performance figures. Table I, column heading, "Repair Parts Cost per Ton," is still another item which will not stand up under comparison unless the loaders involved are put into type classes, i.e., there are simply no means possible to show the repair costs of scraper loading versus a caterpillar mounted loader in abrasive material. The source of information here is also important. Actual field tests have proved that these costs are of a constant nature. Manufacturers are striving to hold them to a minimum and many interesting studies have been made. A fairly recent example of this in a large United States gold producer has proved that Joy HL-3 loaders can be consistently average, less than $0.025 per ton mucked. This cost represents repair labor and parts over a two year

Jan 1, 1952

NORTH AMERICA Number Members Alaska 32 Canada 300 Mexico 165 Newfoundland 3 United States Alabama 43 Arizona 121 Arkansas 9 California 674 Colorado 184 Connecticut 94 Delaware 19 District of Columbia 120 Florida 17 Georgia 5 Idaho 66 Illinois 211 Indiana 56 Iowa 8 Kansas 32 Kentucky 31

Jan 1, 1934

By C. N. J. Wagner, E. N. Aqua

Dilute Fe-Si alloys (0 to 5 wt pet Si) were cold-worked by making filings at room temperatuve. The analysis of the broadening of the X-vay powdev pattern peaks yields anisotropic particle sizes normal to the (110), (100), and (112) planes which are a consequence of deformation faults (probability a) and twin faults (probability p). The combined fault probability (1.5a +ß) increases from 0.01 in pure iron to 0.02 in Fe-5 pct Si. The root mean square stvains vary with crystallographic ovientation due to elastic anisotropy of the alloys, and increase from about 0.0035 in pure iron to 0.005 in Fe-5 pct Si measured in the [100] direction. Assuming that deformation and twin faults occur with equal probability, the X-ray data would imply that the stacking-fault energy does not change upon alloying. THE crystallographic aspects of the plastic deformation of dilute Fe-Si alloys has been studied many times since the observation of glide band structures by Barrett et a1.l These glide bands were much straighter than the wavy bands observed by Gough2 in unalloyed iron nearly 40 years ago. This difference in the morphology of the slip band structure has been verified many times, most recently by replication electron microscopy3 and dislocation etch-pitting methods.4,5 These observed differences in deformation behavior have been considered to result from the degree of cross slip that occurs in pure iron and in the Si-Fe alloys. The lowered tendency for cross slip would result from a lowering of the stacking-fault energy of iron by the silicon alloying addition. Experimental evidence for this lowered stacking-fault energy in the Si-Fe alloys, obtained with transmission electron microscopy, is the observation of dissociated dislocations in Fe-6 pct si6 and Fe-3 pct Si alloys,7 and the observation of sharply defined cellular substructures in Fe-3 pct si6,7 compared to the more diffuse substructure in zone-refined iron.&apos; The activation energy for recovery of cold work is greater in the Si-Fe alloys than it is in pure iron, indicating that cross slip has become a more difficult process.9 The purpose of this investigation is to determine the change in stacking-fault probability from the broadening of powder pattern peaks in dilute silicon-in-iron solid solutions, when cold-worked at room temperature. The knowledge of the stacking-fault probability and the dislocation density, both of which can be deduced from line-broadening analysis of two orders of reflections from (110), (200), and (112) planes, will permit us to calculate the change in stacking-fault energy upon alloying silicon into iron. Previous X-ray investigation of cold-rolled Fe-5 wt pct Si (100)[001 ] single crystals did not reveal any line broadening, whereas cold-rolled Fe-3.1 wt pct Si (001) [110] and (001)[100] single crystals10 showed line bro2dening as a consequence of small particle sizes (-200A) and root mean square strains (-0.25 pct), which are comparable to those found in cold-worked iron filings.11 EXPERIMENTAL PROCEDURE A series of five Fe-Si alloys containing nominally 1 to 5 wt pct Si and pure iron were cold-worked by making filings at room temperature. The actual silicon content deviated at the most by +0.1 pct which is of no significance in the present study. The carbon contents of these materials were less than 0.02 pct. The X-ray diffraction patterns were measured with molybdenum, cobalt, and iron radiation using a GE and a Philips diffractometer. The (110)-(220), (200)-(400), and (112)-(224) pairs of reflections were

Jan 1, 1968