Search Documents

By H. Rosenthal, A. L. Jamieson

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

THE CHAIRMAN (EDWIN LUDLOW, Lansford; Pa.).-Mr. Wang's paper reminded me that some years ago I was asked if I would not go into the Tien Tsin district and take charge of Americanizing a Chinese mine. They said the trouble was that, while wages were only 9 c. a day, the coke cost $2 a ton delivered to the cars. Reading Mr: Wang's paper would indicate the need of a little Americanization in the Manchurian field. Wages are only 40 c: a day, yet the cost is $3.60 a ton. An efficiency engineer would have an excellent opportunity in that field. T. T. READ, New York, N. Y.-It is always true that low-priced labor is inefficient, wherever we find it; for example, in Japan, where wages are low, but not so low as in Manchuria, working costs are not relatively much lower than ours. Mr. Padshah, describing his experience in India, once told me that, while wages were only about one-fifth as high

Jan 4, 1918

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By E. T. Turkdogan

This is a compilation and a critical review of the data on the Fe-Ca-0 ternary system. Using the results on the reductiorz-equilibria, an oxygen potential diagram is drawn for the greater part of the system. A number of univariant systems and invariant points, not determined experimentally, are evaluated by making use of the theorem on univariant curves intersecting at an invariant point. The formation of solid solutions and ternary compounds and the crystal structures of some of the phases in the composition-diagram are given for a feu! temperatures. DURING the past thirty years there has been a continued interest in the study of the Fe-Ca-0 system. A detailed literature survey made by white1 in 1943 indicated that further work was required to clarify the phase relationships; in fact, the work carried out in the subsequent years, reviewed by Burdese2 in 1954, made a valuable contribution to a better understanding of this subject. Most of the data were obtained by the step-wise reduction of mixtures of iron oxides and calcium ferrites. However, there is some uncertainty about the phase relationships in this system, arising mainly from insufficient use of thermodynamic concepts in the construction of phase diagrams. In this paper an attempt is made to establish the invariant points from the available data. OXYGEN POTENTIAL DIAGRAM Schenck and coworkers3,4 were the early investigators who studied part of this system by the step- wise reduction method and suggested the formation of two ternary compounds, CaO.FeO.Fe2O3 and 2Ca0.5Fe0.2Fez03, the latter being referred to as point X. They also deduced from their results that the phases Y (8.74Ca0.32.5Fe0.8.74Fe2O3 and Z (2.02CaO-97.98FeO) were formed near the w?stite corner of the system. Martin and voge15 postulated the existence of the compounds CaO.9FeO and 4Ca0.3Fe3O4; the former is very close to the composition of point Z and the latter to that of CaO.FeO-Fe2O3. The most valuable contribution to the presen knowledge on this system was made by Cirilli and Burdese6-8 who showed by X-ray and chemical anal yses that there were two ternary compounds, CaO-Fe0.Fe2O3 and CaO.3FeO-FezO3; the former is the same as that suggested by Schenck et al. and the latter is close to their point X. The results of Cirilli and Burdese show that the phases Y and Z postulated by Schenk et al. are solid solutions of calcium oxide in w?stite. In most of the above-mentioned reduction-equilibria measurements carbon monoxide-carbon dioxide mixtures were used and in a few cases hydrogen-water vapor mixtures were employed. Using the

Jan 1, 1962

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By N. A. Gokcen

EQUILIBRIA in the reactions between gases and liquid metals have been the subject of many interesting investigations. The experimental realization of true equilibrium, however, is questionable in certain cases due to the lack of conclusive studies in reaction rates. It -will be shown here that a systematic interpretation of rate studies with the analysis of prevailing experimental conditions leads to valuable practical information. The reactions of particular interest are: H2(g) +S(inFe) - H2S(g) [1] H2(g) +O (inFe) =H2O(g) [21 2H2(g) + SiO2(s) = 2H2O(g) + - (inFe) [3] The usual and perhaps the most convenient method of investigation may be illustrated with reaction 1. A stream of gas mixture consisting of H2 + H2S is passed over or bubbled through the liquid metal at constant temperature. The ratio of H2S/H2 in the entrant mixture is fixed in each experimental run, and, therefore, the composition of melt varies until the establishment of equilibrium. The purpose of this paper is to derive a formula expressing the minimum time required for the establishment of equilibrium and to compare the calculated values from such a formula with the available data. Equations Reaction 1 is used for the purpose of illustrating the derivation. Let E represent the equilibrium and X the nonequilibrium sulphur in weight percent at any time t in minutes. For the sake of simplicity, it is first assumed that E > X although the results are of general applicability without restriction. It has been shown by Morris and Williams' that within a difference of 1 pct S or less, i.e., E-X5 1.00, the value of K'1 = Ph2s/Ph2.S% is very nearly constant. The maximum ratio of available Ph2s/Ph2 = H,S/H,, from which sulphur can be absorbed by metal, is equal to H2S/H2 in equilibrium with E (which equals H2S/H2 in the entrant gas), minus H,S/H, in equilibrium with X. Thus: Available H2S/H2 = EK'1 - XK'1 [4] Eq. 4 expresses that sulphur can be absorbed by metal from the H2S/H2 in the entrant gas until the gas leaving the metal assumes a value of H2S/H2 which is in equilibrium with the dissolved sulphur X at that time. H,S constitutes up to approximately 1 pct of the gas mixture. Its disassociation into H2 and SL is about 1 pct at 1600°C, hence, the H2S/H2 impinging on the surface of metal is very close to that in the entrant gas. The rate of flow of hydrogen entering the reaction chamber is kept constant experi-

Jan 1, 1954

In 1974, iron pellet production in the Great Lakes region reached the 53-million-tpy level, accounting for more than 88% of the nation's pellet production. By 1978, pellet output from the Great Lakes district will climb to at least 78 million tpy. To achieve this 50% increase in output, the US iron and steel industry is investing at least $1.25 billion in new mines and pelletizing plants, mostly in Minnesota and Michigan. The biggest effort is concentrated in the Mesabi Range of Minnesota, the heart of the US steel industry's major iron ore source: here, plans for two new taconite plants-one by Hibbing Taconite Co., and the other by Inland Steel Mining Co.-and three major expansions of existing facilities are already under way to boost Minnesota's total iron pellet capacity from the current 41.2 million tpy to 65 million tpy by 1978. The facilities being expanded are those of US Steel Corp. (Minntac operations), Eveleth Taconite Co., and National Steel Pellet Co.

Jan 11, 1975

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y' phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS' showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969

By E. C. Smith

THE CHAIRMAN.-Mr. Earle Smith- has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. SMITH,* Cleveland, Ohio-I will start this off by a story of the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "We don't make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don't dare publish the information. So if I collect it and hide it you can't charge me with having done anything that really disrupted the commercial situation. So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "-academic-matter-as far as II am concerned. ¬I am in a situation like that of the German who was told in 1936 about the coming war. He said: "Until it is your throat that is going to be cut, you don't pay any attention to what is happening to the other man." That is the way with the problem that we have in front of us. Recently I have been told that the comptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were not within the compositions that were included in the specification, and therefore he as the comptroller had no alternative. It was not meeting the specification; therefore, no payment. So I would say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative chemists who analyze some of these products or lawyers who read specifications. I don't know which man is going to be the major factor in the future. If the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for what they expect to be umpire results, the writers would certainly realize that some of the specifications to which we have calmly signed our names as being O.K. are well, as one man said to me, they might be filled by the devil, and they, certainly could be filled by the Lord, but they could not be filled by mankind. I would like to inject two or three things into a segregation study which I want you to think about, because I would be a little surprised if there is very much discussion of them. In the first place, we generally make steel in the United States in the basic open hearth, and I do not think there has been nearly enough consideration given to segregation within the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0.60 per cent silicon have more respect than they had previously for the segregation that is within the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another point to which I think we ought to give serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregating iron oxide. Normally we are segregating some form of carbon or sulphur, or something like. that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1944

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

By N. A. Gokcen, M. Ohtani

Thermodynamic intevaction pararnetevs of elements E2(2), for dilute binary solutions of a component "2" in liquid iron, i.e., E(22) = 9 In f2/?N2 where f2 is the activity coefficient and N2 the mole fraction, and E(3) 2 = In f2/ N3 dilute ternary solutions of "2" and "3," and the carbon saturation parameter sc(3) (In f c/ N3) N c/N Fe for N3 - 0, are critically examined and correlated. It has been found that the interaction parameters and the atomic numbers of alloying elements follow regular periodic putterns. PHYSICO-chemical behavior of alloying elements in molten iron have become the subject of numerous investigations during the past 25 years. Consequently, the mutual effects of elements in the iron-rich solutions Fe-C-X, Fe-N-X, Fe-H-X, Fe-O-X, and Fe-S-X where X represents an alloying element, have gradually become better understood. These effects for a given temperature and pressure may be expressed by the interaction parameter of Wagner1, 2 derived briefly in the following manner. The complete differential of the Gibbs free-energy equation at constant temperature and pressure is dF = Fl dn, + F2 dn, + F3 dn3+ . . . [ 1] where F is the free energy; F 1, the partial molar free energy of "I"; and n,, the number of moles of "i." Cross-differentiation of this expression* *Cross-differentials are obtained as follows: Since the order of differentiation of F with n2 and n3 is immaterial, the left sides of the second differentials are equal, hence the derivation of Eq. [2] is obtained. For a dilute solution of components 2 and 3 in solvent 1, with the substitution of RT In f i = Fi xs for Fi where fi is the activity coefficient, and Fixs is the excess partial molar free energy, Eq. [2] becomes O) [3] where N2 and N, are the mole fractions. The interaction parameters are defined by

Jan 1, 1961

By T. B. Massalski, H. W. King

An hcp phase may be induced by cold working the ß&apos; phase of the Ag-Zn system. This phase reverts to ß&apos; on subsequent aging. No phase change occurs on cold working the o phase, but ß&apos; is formed when the deformed alloy is subsequently aged at room temperature. It is concluded that for alloys near 50 at pct Zn the ordered bcc ß&apos; phase is the equilibrium structure at room temperature. WhEN the disordered bcc ß phase of the Ag-Zn system is cooled to temperatures below 258o to 274oC, it transforms to a complex hexagonal phase <o.1,2 The nature of the o ß=o transformation has been the subject of some discussion,2&apos;3 and the structure of o has been described in detail.&apos; The latter phase appears to be stable on aging at room temperature but decomposes following cold work. When alloys containing approximately 50 at. pct Zn are rapidly quenched from the 0 phase field, the ß ? o transformation may be suppressed; but the ß phase undergoes an ordering reaction (ß ? ß&apos;). The ß&apos; structure may also be obtained as a result of cold working and aging at room temperature.4 Kitchingman, Hall, and Buckley4 have suggested that the decomposition of (o following cold work proceeds in two stages, (o ? ß followed by ß ? ß&apos;, but did not confirm this by experiment. When the ordered &apos; phases in the systems Cu-Zn5 and Ag-Cd6 are cold worked, they become unstable and transform to a close-packed hexagonal phase (( ) indicating that when order is destroyed in a ß&apos; structure the close-packed hexagonal phase may in many cases be more stable. It thus became of interest to study more closely the effect of cold work and annealing on the stability of both the ß&apos; and o phases in a Ag-50 at. pct Zn alloy. Predetermined weights of spectroscopically-pure Ag and Zn, supplied by Johnson and Matthey, were melted and cast under 1/2 atm of He in transparent vycor tubing. The ingot was homogenized for 1 week at 630°C and quenched into iced brine. Since mechanical polishing was found to induce a phase change, sections were first polished at room temperature, sealed in tubes under 1/2 atm of He, reannealed for several days at 630o or 200°C and then quenched into iced brine. Sections of the alloy thus prepared were found to be homogeneous when examined under the microscope. The sample quenched from 630°C (ß -phase region) was pink in color, whereas the sample quenched from 200°C (o-phase region) was silver. The latter sample showed the characteristic hexagonal anisotropy when examined under polarized light. Filings of the alloy were examined at room temperature, after various heat treatments, using an RCA-Siemens Crystalloflex IV diffractometer with filtered CuKa radiation. The X-ray reflections from flat powder specimens quenched from 630o and 200°C and sieved through 230 mesh were recorded graphically at a scanning speed of 1/2 deg per min. The resultant patterns are shown in Figs. 1(a) and 1(b) and may be identified as those of the 8&apos; and <02 structures respectively. The lattice parameter of the ß&apos; phase was determined as 3.1566Å.* This value compares very well withthatto be expected for a 50 at. pct Zn alloy from the data of Owen and Edmunds? and indicates that no loss of Zn occurred during casting. In order to study the effect of cold work upon the ß&apos; and o phases, filings made at room temperature and sieved through 230 mesh were mounted immediately in the diffractometer-i.e., without a strain-relief anneal. Changes in structure on subsequent aging were followed by scanning repeatedly over the regions of the low index reflections of the ß&apos; and o structures-i.e. , 28 from 35 to 44 deg. Immediately after filing the 8&apos; specimen, additional diffraction peaks were observed in the low-index region of the pattern, as shown in Fig. 1(c). These additional peaks do not coincide with those of the o structure, Fig. l(b), but may be indexed as the (10.0), (00.2), and (10.1) reflections of an hcp phase (<) with nearly ideal axial ratio. However, this hexagonal phase appears to be very unstable since within a very short time at room temperature it reverts back to the ordered ß&apos; phase, the reversion being complete within seven hours. The 5 ? ß&apos; reversion reaction is, therefore, very similar to those already reported in Cu-Zn5 and Ag-Cd6 7&apos;alloys. The action of filing caused the deformed surface of the originally pink ingot to become silver in color, indi-cating that the ( phase possesses similar reflecting properties to the o phase. Hence, the subsequent

Jan 1, 1962

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T&apos; dT&apos; ?T&apos; ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By Theron Wasson

The oil and gas fields of Michigan that have been under development since 1925 are in an area that extends across the middle of the lower peninsula from northeast to southwest, a distance of about 200 miles, and with a width of about 80 miles. In 19 years 70 fields have been discovered. Most of these are relatively small when compared with other oil-producing areas. This is borne out by the fact that since the first wells were drilled these fields have produced a total of only 204,000,000 bbl. However, Michigan is still maintaining its production, for during the past five years the annual production has remained fairly constant at approximately 20,000,000 bbl. Production for 1943, as reported by the Bureau of Mines, was 20,682,000 barrels. Roughly, one third oi Michigan&apos;s production in 1943 came from the Reed City field, which was discovered in 1941. During the year, 237 oil wells were completed in Michigan in 1943. The decrease of 56 from the 1942 total is probably due to the continuance of Government regulations requiring a 40-acre spacing pattern over most of the state. Fig. I shows the principal oil and gas fields of Michigan, and the columnar section, Fig. 2, shows the principal producing horizons in relation to the section drilled. The data of Table I and Table 2 have been carefully checked with previous reports to eliminate errors. Six new producing areas were discovered during 1943 and five areas discovered in 1942 were developed during the year. Both the new discoveries and the 1942 discoveries that were developed appear to be small and relatively unimportant. Goodwell Field.—The best discovery of the year is the Goodwell field, T. 14 N., R. 11 W., Goodwell township, Newaygo County. This small structure was located by core testing done by The Pure Oil Co. in 1942 and early 1943. The first producing well, C. R. Harris No. I, was completed on July 5, 1943, ill the Traverse limestone at a total depth of 2742 ft., with ail estimated potential of 1100 bbl. per day. By the end of the year, 18 wells had been completed in this field and approximately 281,000 bbl. of oil produced. The field operated under proration of 262 bbl. per day per well from Oct. I to Dec. I; 150 bbl. per day per well after that date. Woodville Field.—The small Woodville pool, T. 15 N., R. 11 W., 3 miles north of the Goodwell field, was discovered by core testing by the Ohio Oil Co. The discovery well was completed on May 5, 1943, flowing 650 bbl. of fluid, including 18 per cent salt water the first 18 hr., from the Traverse limestone at a depth of 2810 to 2815 ft. Seven wells had been completed by the end of the year and 67,000 bbl. of oil had been produced. Development is now practically at a standstill because further drilling does not aDDear economically iustified.

Jan 1, 1944

By Theron Wasson

The oil and gas fields of Michigan that have been under development since 1925 are in an area that extends across the middle of the lower peninsula from northeast to southwest, a distance of about 200 miles, and with a width of about 80 miles. In 19 years 70 fields have been discovered. Most of these are relatively small when compared with other oil-producing areas. This is borne out by the fact that since the first wells were drilled these fields have produced a total of only 204,000,000 bbl. However, Michigan is still maintaining its production, for during the past five years the annual production has remained fairly constant at approximately 20,000,000 bbl. Production for 1943, as reported by the Bureau of Mines, was 20,682,000 barrels. Roughly, one third oi Michigan&apos;s production in 1943 came from the Reed City field, which was discovered in 1941. During the year, 237 oil wells were completed in Michigan in 1943. The decrease of 56 from the 1942 total is probably due to the continuance of Government regulations requiring a 40-acre spacing pattern over most of the state. Fig. I shows the principal oil and gas fields of Michigan, and the columnar section, Fig. 2, shows the principal producing horizons in relation to the section drilled. The data of Table I and Table 2 have been carefully checked with previous reports to eliminate errors. Six new producing areas were discovered during 1943 and five areas discovered in 1942 were developed during the year. Both the new discoveries and the 1942 discoveries that were developed appear to be small and relatively unimportant. Goodwell Field.—The best discovery of the year is the Goodwell field, T. 14 N., R. 11 W., Goodwell township, Newaygo County. This small structure was located by core testing done by The Pure Oil Co. in 1942 and early 1943. The first producing well, C. R. Harris No. I, was completed on July 5, 1943, ill the Traverse limestone at a total depth of 2742 ft., with ail estimated potential of 1100 bbl. per day. By the end of the year, 18 wells had been completed in this field and approximately 281,000 bbl. of oil produced. The field operated under proration of 262 bbl. per day per well from Oct. I to Dec. I; 150 bbl. per day per well after that date. Woodville Field.—The small Woodville pool, T. 15 N., R. 11 W., 3 miles north of the Goodwell field, was discovered by core testing by the Ohio Oil Co. The discovery well was completed on May 5, 1943, flowing 650 bbl. of fluid, including 18 per cent salt water the first 18 hr., from the Traverse limestone at a depth of 2810 to 2815 ft. Seven wells had been completed by the end of the year and 67,000 bbl. of oil had been produced. Development is now practically at a standstill because further drilling does not aDDear economically iustified.

Jan 1, 1944

By A. D. Zunkel, A. H. Larson

Equilibrium antimony contents of pb-sb alloys in contact with PbO-Sb2O3 slags containing less than 45 mole pct Sb203 uleve determined at 650&apos;, 700°, and 750°C in an inert atmosphere. In this ten~pevature range, the antimony contmzt of the alloy increased with increasing temperature at all slag compositions. The PbO-Sb203 phase diagram below 28 mole pct Sb2O3 was determined by thermal analysis and by application of a log sbZ4/y$b0 us plot determined from the equilibrium-activity data. The resulting phase diagram showed a eutectic at a temperature of 604°C and a comfiosition of 21.6 mole pct Sb2O, with a maximum terminal solid solubility of Sb203 in PbO of 5.6 mole pct. These results are compared with existing data in the literature. In the past three decades, only a small amount of experimental work has been done on the slag-metal equilibria in the Pb-PbO-SbaO3 or the analogous arsenic and tin systems. These systems are important in commercial lead-refining processes such as softening and dross fuming since it is impurities such as antimony, arsenic, and tin in lead bullion and Sb2O3, As2O3, and SnOz in lead drosses which must be re-

Jan 1, 1968

By C. Crussard, R. Tamhankar

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers accord-ing to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Gerhurd Derge Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Staff Coordinator, James J. Burke THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Past-President; John Chiprnan, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman; Dennis Carney, John Chip-man, J. C. Fulton, J. H. Hollomon, H. H. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and D. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman, F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham, .Jr., Robert F. Hehemonn, R. I. Jaffee, F. E. Jaumot, Jr., Irving R. Kramer, A. J. Lena, Harold Margolin, C. J. McHorgue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alan U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B. King, F. C. Langenberg, W. 0. Philbrook, and T. 0. Winkler. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for non-AIME members in United States and North, South, and Central America; $25, foreign; $5 for AIME members. Single copies, $4.00, single copies foreign, $5.00. The AIME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AIME New York ... Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts... Second class postage paid at New Yark, N. Y., and Ann Arbor, Mich. Volume 212, Number 6.

Jan 1, 1959

By O. Schaaber

THE existence of isothermal martensite without the presence of the athermal form thus far has been established only in a 6 pct Mn, 0.6 pct C steel&apos; and a 23 pct Ni, 3.5 pct Mn-Fe alloy.&apos; " Theoretical calculations, moreover, predict this phenomenon to be observable only within narrow composition limits.&apos; In all other steels, it is generally considered that martensite inevitably forms upon cooling below the M, temperature. Even the possibility of isothermal martensite transformation has been questioned for the common steels, although Averbach and Cohen" showed that martensite formation does not stop when the cooling is arrested and that as much as 5 pct retained austenite may transform isothermally to martensite at room temperature. This note presents some observations made on a number of low alloy steels by dilatometric and inductive measurement of isothermal austenite transformation at various temperatures close to the Ms. In the dilatometer studies reported previously, austenitized specimens were immersed in a salt bath maintained at proper temperature and immediately inserted into the dilatometera8&apos; already at thermal equilibrium with the bath. The dilation was read on a dial gage divided into 0.001 mm intervals. Induction measurements were made with a separate excitation source and a test coil, sealed together in a salt-tight case. The increase in the induced voltage caused by the transformation products was recorded at a paper speed of 4 mm per sec. The steels studied are listed in Table I. Specimens prepared from steels 1 and 2 were in the form of hollow cylinders 60 mm long, 10 mm ID, 14 to 16 mm OD, while specimens of steels 3 and 4 were in the form of notched-bar impact test specimens, DVM type. Specimens of steel 5 were in the form of strip, 7x0.3 mm. In the bainitic range, curves representing the amount of transformation vs log time have a single step appearance, as is shown by the curve of isothermal transformation at 320°C in Fig. 1.Y ransformation proceeds in accordance with the Austin-Rickett equationo P -----------= k t" 100-P where P is the percentage of transformed austenite, t is time, and k and n are constants. Near the M, temperature, however, complex curves having two steps are observed. As shown in a previous papera for steel 3 isothermally transformed at 245"C, such complex curves can be separated into two separate transformations or reactions each following the Austin-Rickett equation. The values of n in the equation for a number of such two-step transformations are listed in Table 11 for steel 1. At transformation temperatures of 250" and 235"C, evidence of a second transformation is very

Jan 1, 1956

By E. T. Turkdogan

The activities of SiO2, FeO, and Fe2O3 are calculated from previous experimental data on the activity of oxygen in Fe-Si-O melts at 1550°C. Using the oxide-activity data, the free energy of formation of fayalite from its oxides is evaluated for 1550°C. A number of investigators1-4 contributed to the study of the state of oxidation of iron in SiO,-FeO-Fe,O3 melts and the phase equilibria in the system Fe-Si-O. In a more detailed study, Schuhmann and Ensio5 and Michal and Schuhmann% easured the state of equilibrium in the SiO,-FeO-Fe,O3 melts saturated with y-iron or silica or both under low-oxygen potentials and within the temperature range 1250" to 1350°C. Similar measurements were also made by Turkdogan and Bills7,&apos; over wide ranges of composition and oxygen potentials at 1550"C. Using the experimental data on the oxygen activities in the ternary system, Schuhmann&apos; calculated the activities of silica and ferrous oxide in Si0,-FeO-Fe2O3 melts for 1350°C. Adequate knowledge on the activities of the constituent oxides of melts is essential in the study of reaction-equilibria and reaction-kinetics in oxide-melts. With this in view, the activities of oxides in SiO2-FeO-Fe2O3 melts at 1550°C are computed using the experimental data of Turkdogan and Bills7&apos;8 on the oxygen activities in these melts.

Jan 1, 1962

By H. M. Morse

This report covers the period from Jan. I, 1943 to Dec. 31, 1943. During the year, II2 wells were drilled in Mississippi, as foilows: wildcats drilled and abandoned, 54; wildcats producing oil, 4; oil wells drilled in oil fields, 26; oil wells drilled in fields, dry and abandoned, 10; sulphur-test wells drilled, 14; salt-water-disposal wells, 3; core tests, I. Prospecting Geophysical work in Mississippi during 1943 amounted to 1127 crew weeks, divided as follows: reflection seismograph, 809 weeks; gravity meter, 285; magnotometer, 30; torsion balance, 3. A considerable amount of core drilling was done over a large part of the state. The complete data on this activity are not available at the present time. Salt Domes To date, the following salt domes have been discovered in Mississippi: Midway, Edwards, Glass, Newman, Tatum, Oak-vale, Kings, Halifax, D&apos;Lo, Hazlehurst, Byrd, Leedo, Prentiss, Carson, Moselle, Monticello, Ruth, Keno, Taylorsville. New Oil Fields Lincoln County.—On March 10, 1943, the California Company completed its Smith No. I in sec. 4, T. 7 N., R. 7 E., Lincoln County, as an oil well and produced 29 bbl. of 25" gravity oil in 24 hr. through a fi-in. choke. Two outpost wells have been drilled in this area by the California Company, and both have been abandoned as dry holes. Madison County. —Love Petroleum Co. completed its J. R. Anderson No. 2, sec. 2, T. 8 N., R. I W., Madison County, on Sept. 7, 1943. This well produced 135 bbl. of approximately 30" gravity- oil in 24 hr. through a )/4-in. choke. The production comes from a sand or porosity in the upper part of the Chalk formation of the Cretaceous age. Adams County.—The California Company drilled its National Gasoline Co. of Louisiana No. I in sec. 52, T. 7 N., R. I W., to a total depth of 10,383 ft., and at 10,280 ft, it perforated and obtained gas and a condensate. The well had several showings in the Wilcox of the Eocene age. Several of these showings were tested and the well finally was completed at 5888 ft. on Oct. 6, 1943, producing 44" gravity oil in the second sand in this formation. No other wells were completed in this field during the year. However, a number of wells are contemplated in the near future, and locations have been staked by the California Company. The Oklahoma Pipe Line Co. will market the oil through its pipe-line facilities. Wayne County.—The Gulf Refining Co. drilled Davis No. I in sec. 2, T. 9 N., R. 9 W. in Wayne County. After several stem tests 545&apos;-in. casing was set at 6850 ft. and production was obtained in the so-called Massive Sand of the Lower Tuscaloosa. The well produced 359 bbl. of oil in 24 hr., and it Was completed on Oct. 4, 1943. Other locations have been staked ill this area and probably will be drilled in 1944 by

Jan 1, 1944