Search Documents

By Leonard B. Lipson

Boyer, Morgan and Muskat,' with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,' have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/'E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By Leonard B. Lipson

Boyer, Morgan and Muskat,' with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,' have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/'E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By J. H. Brophy, S. J. Michalik

A constitution diagram for the system Mo-Ir has been determined. The maximum solubility of iridium in molybdenum is 16 at. pct at 2110ºC and decreases to less than 5 at. pct at 1500°C. The solubility of molybdenum in iridium is 22 at. pct. Three intermediate phases appear in the system: 8 MoJr, having the p-tungsten structure; a phase, a cornplex tetragonal structure; and the hcp ? phase. Metallography, melting point determinations, X-ray diffraction and fluorescence, and electron micro-probe unalyses were employed in establishing the diagram. PREVIOUS to the present investigation, the intermediate phases in the Mo-Ir system were identified, but no detailed account of the phase diagram has been reported in the literature. Raub1 investigated alloys of Mo-Ir over an extensive range of composition between the temperatures of 800º and 1600°C. The in-termetallic compound MosIr was found to exist with nearly pure molybdenum, as the solubility of iridium in molybdenum was not detectable parametrically in this temperature range. MO3Ir was found to be iso-morphic with a ß-tungsten type structure, having a parameter of 4.959Å. An intermediate hcp phase, designated as the ? phase, ranged in composition from 52 to 78.5 at. pct at 800ºC, and from 41 to 78.5 at. pct Ir at 1200°C. Parameters noted for the ? phase were as follows: at 42.7 at. pct Ir, a = 2.771i0, c = 4.4366, c/a = 1.601; at 78.5 at. pct Ir, a = 2.736A, c = 4.378A, c/a = 1.600. Molybdenum was found to be soluble in iridium up to 16.5 at. pct Mo (83.5 at. pct Irj, with the parameter of iridium increasing to 3.845A at the solubility limit. Knapton,2 who investigated alloys between 15 and 85 at. pct Ir, essentially agreed with Raub's data, but, in addition, found a a phase in as-melted alloys near 25 at. pcto Ir. The oaphase lattice parameters were a = 9.64Å, c = 4.96Å, c/a = 0.515. The a phase was replaced by the 8 -tungsten phase on annealing at 1600°C. Knapton concluded that the a was stable only at elevated temperatures, and placed the composition of the a phase at approximately 30 at. pct Ir. The intermetallic compound Mo3Ir, with a lattice parameter of 4.965A, was included among the 8-tungsten structures reported by ~eller.' Matthias and Corenzwit,4 and Bucke15 studied the superconducting nature of MosIr, and reported a superconducting transition temperature of 8.$K. The present investigation describes the phase relationships in the Mo-Ir alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURES Alloys for the determination of the phase diagram were prepared from powders. Commercial 99.9 pct Mo from Fansteel Metallurgical Corp. and 99.9 pct Ir powder from J. Bishop and Co. Platinum Works were used. The powders were weighed to nominal compositions, mixed, and then pressed, without binder, into compacts weighing 4 to 6 g. These were presintered in uacuo between 1200' and 1400°C for 1 hr, to reduce the degree of spattering during subsequent arc-melting. The compacts were arc-melted in a nonconsumable tungsten electrode furnace six times on alternate sides on a water-cooled copper hearth in an atmosphere of zirconium-getter ed argon at 500 mm of mercury pressure. In almost all cases, this procedure yielded buttons of satisfactory homogeneity. The composition of all melted buttons were confirmed by X-ray fluorescent analysis using the experimentally determined ratio of the iridium La1 line intensity to that of the molybdenum Ka1 line as a function of composition. In this determination four alloys analyzed by wet chemical methods were used as standards. An uncertainty range of ±1 at. pct has been attributed to all indicated compositions. All heat treatments and solidus measurements were carried out in tantalum resistance heating elements in vacuum conditions of 10-4 to 10-5 mm of mercury. A detailed account of this procedure has been reported by Schwarzkopf and Brophy.8 In the heat treatment and solidus measurements of iridium-rich alloys (50 at. pct Ir or greater), a tungsten lining was inserted into the tantalum resistance heating element because of a eutectic reaction which occurs between iridium and tantalum at 1948ºc.7 Heat treatments and solidus measurements carried out at compositions less than 40 at. pct Ir both with and without tungsten linings within the resistance

Jan 1, 1963

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937

THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enormous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engineers, superintendents, and' others, in mastering &he problems which are constantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal-liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects : 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the periodical publication of essays or papers, communicated to such societies by their members. I t must be evident to all practical men that the interchange of the varied experience of those engaged in such occupation in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centers, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. I t is proposed that a meeting of those sympathizing with the object above mentioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By C. Hays, R. E. Swift, E. G. Kendall

Investigations of the Zr-Pt system, by metallography, incipient melting, and X-ray diffraction, determined the phase relationshifis from 0 to 50 at. pct Pt. Phase fields in the Pt-~ich region were outlined, and three intermetallics (ZrPt, Zr2Pt, and ZrPtd were located. A eutectic between Zr and Zr2Pt, and a eutectoid veaction between Zr and a Zr + Zr2Pt, were established. The maximum solubility of Pt in P Zr was approximately 13.5 wt pct, as opposed to less than 1 wt pct solubility in a Zr. EARLIER work on the Zr-Pt system was limited to an X-ray study on the intermetallic compound, ZrPt3, by H. J. Wallbaum,1 It was reported that ZrPt3 existed at 86.52 wt pct Pt, and had a hexagonal structure, isomorphous with TiNi3. Wallbaum's data revealed the following structural particulars: a = 5.633A, c = 9.21A, and c/a = 1.635A. Other studies allied to Zr-Pt alloys concerned only 1) Pt-rich alloys (0.05 to 5.0 pct Zr) for corrosion resistance,2 2) a Zr-base alloy with 5 pct Pt and 0.124 pct C for oxidation resistance,3 and 3) electroclad-ding of Zr with Pt for in-pile corrosion resistance of Zr to uranyl sulphate. 4 Metallographic, incipient melting, and X-ray diffraction techniques were applied to accurately resolve the phase relationships in the 0 to 50 at. pct (68.2 wt pct) Pt region, and to outline the phase fields in the Pt-rich area. Three intermediate phases: Zr2Pt, ZrPt, and ZrPt3, were also established by the same methods. PROCEDURE Melting stock for this program was of the highest purity obtainable. The Zr was iodide crystal bar with a low hafnium content of about 0.05 wt pct (Westinghouse "Grade 3"). The as-received Zr was treated to remove the surface film of corrosion product that resulted from a standard autoclave grade designation test. Next, the bars were processed to yield material suitable for arc melting and free of contaminants. Sheet platinum metal (Baker and Co. "Grade 2") was used for alloying additions. This material con-

Jan 1, 1962

By Bernard N. Moore

At present the demands of the United States for strorltium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits arc known in many states, but the larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, particularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investigation of the mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work. Celestite Deposits The celestite deposits described in this paper are of sedimentary origin and Tertiary age. They are widely scattered, as shown on Fig. 1,

Jan 1, 1935

By Bernard N. Moore

At present the demands of the United States for strorltium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits arc known in many states, but the larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, particularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investigation of the mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work. Celestite Deposits The celestite deposits described in this paper are of sedimentary origin and Tertiary age. They are widely scattered, as shown on Fig. 1,

Jan 1, 1935

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and 55.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943