Search Documents

By D. G. Westlake

Alloys of poly crystalline Nb-H have been tensile tested at 77" and 120°K after slow-cooling and after quenching from room temperature. A rationale has been developed to explain the effect of cooling rate on ductility in terms of microstructure. The inferior ductility of the slow-cooled alloys in this temperature range can be attributed to the precipitation of coarse hydride particles that fracture in the early stages of plastic deformation. Quenching Produced much smaller hydride particles and a decreased tendency for initia-tion and popagation of cracks. Prismatic dislocation loops, punched into the matrix of quenched alloys, eliminate the yield point and may Play some role in the low temperature ductility of the quenched alloys. The difference in ductility between quenched and slow-cooled V-H alloys was even greater than that observed in the N b-H alloys. It is well known that the ductility of Nb-H and V-H alloys decreases with increasing hydrogen concentra-tion and with decreasing temperature.1-l1 The follow-ing are some of the numerous mechanisms that have been adopted in attempts to explain these observations: 1) hydrogen-dislocation interarction,4'6 2) lowering of the crack surface energy by adsorbed hydrogen,9'10 3) localized lowering of the niobium bond strength,9 and 4) exertion of pressure inside voids by molecular hydrogen.6 A recent study1' indicates that, in some way, the embrittlement is related to the precipitation of a hydrogen-rich phase, because embrittlement and hydrogen solubility have the same temperature dependence. Most of the investigators observed that at very low temperatures there was a return of the ductility. Thus, hydrogenated niobium and vanadium may be said to exhibit a low temperature ductility minimum."1'8'9 It has been reasoned by most observers that diffusion is required for the embrittlement mechanism to be operative, and that as hydrogen becomes immobile at very low temperatures, the ductility increases. This investigation of the mechanical behavior of Nb-H al-loys under various conditions is an attempt to gain a better understanding of the low temperature ductility minimum. EXPERIMENTAL Tensile specimens, with gage length dimensions 20 by 3 mm, were machined from sheet stock" and both faces were ground on wet 600 grit Sic paper to obtain a final thickness of 0.5 mm. Annealing as described earlier12 resulted in average grain diameters of 0.3 mm. The recrystallized niobium tensile specimens were electropolished in 90 parts H2S04, 10 parts HF (48.9 pct) by volume, at 287°K and 30 v. Hydrogen, which may have been present in the starting material and/or added during specimen preparation, was removed by annealing at 1073°K in a dynamic vacuum of 2 X 10-6 torr. Hydrogenated specimens (1.15 at. pct H) were prepared by reaction with a known quantity of pure hydrogen (obtained by thermal decomposition of UH3) at 1073oK, followed by cooling at the rate of 100" per hr. These were vacuum encapsulated, homogenized at 573°K for 3 to 5 hr, and furnace-cooled. Tensile tests were conducted on an Instron machine at a strain rate of 4 x l0-5 per sec. The gripping device was such that the specimen was positioned below the crosshead. Thus, subambient test temperatures could be obtained by immersion of the device in a cooling bath of either liquid nitrogen or Freon-12. The temperature of the Freon-12 was controlled within ± 0.1°K of the desired temperature by automatically monitoring the flow of liquid nitrogen through a copper coil in the bath. Slow-cooling to 77°K was accomplished as follows. The testing device was surrounded by a rubber jacket, open at the top and with small holes in the bottom. Liquid nitrogen, brought up to the bottom of the jacket, entered the holes and vaporized quickly. The temperature was monitored at the specimen with a copper-constantan thermocouple, and a constant cooling rate of 2 deg per min was easily achieved by controlling the level of the liquid nitrogen outside the jacket. RESULTS AND DISCUSSION Low Temperature Ductility Minimum. Resistometric studies of both Nb-H12 and V-H13 indicated that at tem-peratures less than 150°K, virtually all of the hydrogen

Jan 1, 1970

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By Gregory L. Gullord

In September, 1975, production was begun at the new milling facility of ASARCO Incorporated, the Young Mill. The mill is located adjacent to the Young Mine 35 km (22 miles) east of Knoxville, Tennessee. The Young Mill replaced the obsolete Mascot Mill which had been operating since 1913. The basic flow sheet of Mascot was retained for the construction of the Young Mill, with a 20% increase in capacity included in the design. The Young Mill is capable of processing 7710 - t/d (8500 stpd) of crude ore from three underground mines (Young, Immel and Coy) yielding 300 - t/d (330 stpd) of 63% zinc concentrate. The Young Mill is unique in that 92.5% of the ore milled is recovered as saleable products, including zinc concentrate, construction aggregate, sand and agricultural limestone. Processing at the Young Mill is divided into five basic stages: two-stage crushing, heavy media separation, grinding-flotation, concentrate filtering and drying, and limestone by-products recovery. The ore bodies are located in the Knox formation, which consists of primary dolomite, secondary dolomite and limestone with silicas in the form of chert and jasperoid. The zinc mineralization occurs as an exceptionally pure sphalerite. The ore contains an occasional abundance of pyrite and traces of fluorite and barite. TWO STAGE CRUSHING Ore enters the crushing section from two points. The Young Mine ore is hoisted into a 816 ton (900 st) bin which feeds a 1.52m (60 in) conveyor via a 1.52 m (60 in) vibrating feeder. The Immel ore is trucked 10 km (6 miles) by an independent contractor and weighed on automatic recording truck scales at the entrance to the property.

Jan 1, 1977

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer's nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By U. Andres

U. Andres (The Technion, Haifa, Israel)-The authors are to be congratulated on their research, new and interesting, in a field which, however, the present writer and his assistants have been trying since 1962 to bring to the attention of the scientific and technical world, by means of publications covering several different aspects of this many-sided problem. We announced, in these publications, the results of magneto-hydrostatic (MHD) separation of magnetic and nonmagnetic minerals which we made in magnetic fluids (in paramagnetic solutions and suspensions of magnetic particles) which interact with permanent" and impermanent" inhomogeneous magnetic fields. There is no doubt that the authors have succeeded in creating ferrimagnetic colloids made by dispergation of 10-30 wt % of magnetite in kerosene in the presence of 7-10 vl % oleic acid. It may be judged by [Figs. 3 and 4] that the suspensions represent great stability systems and also "hysteresisless" fluids [(Fig. 5)] which bear witness to the existence of superparamagnetic suspensions. If the viscosity of these colloids is not so high, and the cost of preparing them can be covered, the fluids which have here been received can possibly be of interest to the technology of mineral separation. The potential possibility and technological perspective of similar media is demonstrated in our joint work with G. Bunin18 in 1965. The research carried out on the pushing out of cylinders and spheres from magnetic fluid is impressive; it would, however, have been interesting if the authors had compared their results with those on the pushing out of bodies from magnetic fluids adduced from our work." In my books" there happens to be described an experiment on the pushing out of a sphere in magnetic wedge field, in which the pushing out force of suspension with 5 vl % of magnetite reached 125 g per cc. This testifies to interesting possibilities of these media. Our works' shows also, on the basis of Laplace's equation the receiving of an interesting distribution of pushing out forces by selection of corresponding configurations of magnetic poles. Objection must be made to the authors' introduction of the term "antigravity force." The direction of this force does not depend on the direction of the gravity force and their opposition, i.e., antigravity is only one particular case. I am in full agreement with the authors' statement that magnetic pushing out forces "can be utilized to separate nonmagnetic objects according to variations in their densities." It is, however, necessary to make only one important addition, which can be found in our research on MHS at the Technion in Haifa, namely, that magnetic fluids in magnetic fields can be utilized in the separation of minerals according to variations in their magnetic susceptibility. The authors' conclusion is especially important considering the fact that in our publications" (including one in English") some designs of MHS separators and some technological results received on MHS-separators have already been described. S. E. Khalafalla and G. W. Reimers (Authors' Reply)We were aware (mostly through Chemical Abstracts of the American Chemical Society) of the use of solutions of paramagnetic salts such as manganous sulfate in agnetohydrodynamic separations by the Russian school headed by G. Bunin."n Professor Andres' contributions to this school are also evident in his application of the ponderomotive forces in an electrolyte placed in electric and magnetic cross-fields to separate coal and other useful minerals." It must be realized, however, that the foregoing research by Bunin et al." involved the use of magnetic fields and field gradients of very large magnitudes, i.e., such that H • grad H - 101 Oe2 per cm. The magnetization of paramagnetic salt solutions range from 0.1 to 0.5 gauss (at fields of a few thousand Oersteds) and never reach saturation. The magnetization of our superparamagnetic ferrofluids ranges from 100 to 500 gauss and reach saturation at fields of a few hundred Oersteds. Hence, to effect the same separation, the quantity "H

Jan 1, 1974

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Unmodified disilicide coatirigs were applied to sheet-tensile specimens ofCb-Dg3 and Mo-TZM veJractovy- metal alloys. Coating thickness, degree of coating-substrate interdiffusion, and specimen geonzetry (notched and plain were included in the variables studied. Tensile tests were made to determine the ductile-lo-brittle transition temperature. The disilicide coating modestly increased the transition temperatlre of TZM, but had no effect on 043. Neither material condition (recrystallized or stress-velieved) nor specimen geometry (notched or unnotched) significantly altered the effects of coatings on the transilion temperatures of. the alloys. Cracks in the brittle coatings did not propagate into the substrate, and fracture modes appeared to be the same for both un-coated and coated specimens. MOST potential structural applications for refractory metals and alloys involve exposures to oxidizing environments at elevated temperatures. The general lack of oxidation resistance of these metals will require protective coatings to allow fulfillment of their potential. Currently preferred coatings for the oxidation protection of refractory metals are brittle intermetallic aluminides or silicides. These are typically formed on the surface of the refractory-metal substrate by a diffusion reaction between the substrate and a gaseous or liquid medium that is rich in aluminum or silicon. Because of the brittleness of these coatings, they will sustain no plastic deformation at low temperatures. They are frequently cracked by cooling from the coating temperature because of the thermal-expansion mismatch with the substrate alloy. Even if they survive cooling intact, they crack rather than sustain deformation under load at low temperatures. Thus, when a coated refractory metal is strained beyond the elastic limit of the coating at low temperatures, the mechanical environment of the substrate would include both static and dynamic cracks. These might be expected to influence the flow and fracture behavior of the substrate. This could be manifested in an altered fracture mode and/or an increase in the normal ductile-to-brittle transition temperature of the refractory-metal substrate. This paper presents the results of a research program that was conducted to determine the influence of the presence of a brittle surface coating on the low-strain-rate tensile behavior of typical refractory metals at low temperatures. EXPERIMENTAL PROCEDURES Material Preparation. Thirty-mil-thick sheets of molybdenum TZM alloy (Mo-0.5Ti-O.1Zr) and colum-bium D43 alloy (Cb-IOW-1Zr-O.1C) were obtained commercially. These alloys were selected as substrate materials representing two classes of materials important in current refractory-metal technology. The TZM was in the stress-relieved condition, and exhibited a heavily fibered grain structure. The D43 had been processed by the duPont "optimum" fabrication schedule,' and exhibited slightly elongated grains typical of this process. Tensile specimens of two geometries were prepared from these materials: 1) plain specimens with 0.2-in.-wide 1.0-in.-long gage sections; 2) specimens similar to above, but with a 0.06-in.-diam hole drilled in the center of the gage section, providing a stress concentration factor, Kt, of 2.5. The "notch" geometry was selected to represent a typical condition of a rivet hole or other geometric discontinuities as might be encountered in various applications. Machined specimens were degreased, with a final rinse in acetone, prior to the application of coatings. Specimens of each substrate and configuration were pack-siliconizedin a particulate mixture of 80 pct A1203, 17 pct Si, and 3 pct NaF. Specimens were embedded in this mix (contained in graphite retorts) and coated in an electrically heated argon-atmosphere furnace under time-temperature conditions to effect nominal 1- and 3-mil-thick silicide coatings: Coating Thickness, mils Thermal Treatment 0.6 to 1.4 24 hr at 982°C 2.4 to 3.2 48 hr at 1093°C Coating kinetics were similar for both the TZM and D43 substrates. These treatments had little or no visible effect on the substrate microstructure as determined by optical metallography. The coatings on TZM were essentially single-phase unmodified disilicides, while those on D43 showed substantial evidence of modification by proportionate reaction with the respective substrate elements or phases, as shown in Fig. 1. It was recognized that these coatings might not be particularly desirable regarding protective capability. However, it was desired to circumvent possible inter -ferring chemical interaction with the substrate by pack additives such as chromium, titanium, boron, aluminum, and other elements that typify the better protective coatings for these materials.' Thus, the results presented apply specifically to the simple silicide coatings investigated. They may not be rep-

Jan 1, 1967

By J. L. Lytton, T. E. Tietz

The recovery of flour stress of recrylstallized are-cast molyhdenum after 10 pet prestrain at 150°C was studied for recovery temperatures of 725o 801o and 901oC. The yield phenomenon observed after recovery was such that the yield drop diminished and disappeared as recovery proceeded. A fractional flow-stress recovery parameter fr, was developed and it was shown that, independent of recovery ternperatzwe, equal f, values of about 0.16 produced superposition of stress-strain curves except for the initial yield phenomenon. The activation energy for low degrees oj recovery was found to he 32,600 cal per mole, in close agreement with a reported valzie for difjzdsion of carbon in molybdenum. For values of fr greater than about 0.15 where recovery was thought to predominate over strain aging, the activation energy varied from 43,600 to 82,500 cal per mole and increased with increasing recovery and recovery temperature. A 10 pet pre-strain shifted the ductile-brittle transition temperature, as indicated by tensile elongation, from 10°C. to about -22"C. A 100-hr recovery anneal at 801oC was shown to shift the transition temperature to about —5oC, the major shift occurring during the first hour of recovery. ThE recovery of cold-worked metals is accompanied by changes in the arrangement of the dislocations generated during cold work. In recent years, the use of transmission electron microscopy has allowed direct observation of some of the dislocation configurations formed, such as "tangles", networks, cells, subboundaries, and loops. These observations have recently been reviewed by Keh and Weissmann.' Accordingly, some understanding has been gained concerning the nature of the dislocation rearrangements involved. The relationship between recovery and the decrease of mechanical strength, however, has only recently been explored. Previous efforts of the authors were directed toward investigating the decrease of tensile flow stress of aluminum and Al-1 pet Mg during recovery2 and the effects of concurrent elastic and plastic strain on the flow-stress recovery of aluminum.3 In addition, an investigation of the effect of four different solute additions on the tensile flow-stress recovery of aluminum has been made.4 Many important metals, however, have the bee crystal structure, e.g., iron, molybdenum, tungsten, vanadium, columbium, tantalum, and chromium. These metals might be expected to behave differently during recovery from those with other crystal structures for two reasons. First, the previous and present investigations of aluminum and its alloys have shown that tensile flow-stress recovery is strongly affected by foreign atoms in the lattice. In the bee metals, interstitial impurities are usually present and might be expected to have various effects upon both flow behavior and recovery. For example, heterogeneous yielding might occur during prestraining. The diffusion of these interstitials can also relock dislocations during recovery so that a yield point might be obtained upon restraining (strain aging). Second, some of the bee metals (e.g., iron, molybdenum, and tungsten) undergo the familiar structure-sensitive ductility transition and exhibit brittle fracture at suitably low temperatures. It is of considerable interest to determine the effects of recovery on the transition temperature of such metals. The purpose of the present investigation was to extend our knowledge of flow-stress recovery to the bee metals and to study the effects of recovery on the ductile-brittle transition temperature. Unalloyed recrystallized are-cast molybdenum was chosen as a test material, since it exhibits a well-defined ductility transition near room temperature. As in the previous studies, the degree of recovery was measured in terms of the decrease of tensile flow stress. Prestraining and restraining were carried out at 150°C to avoid the possibility of brittle fracture. EXPERIMENTAL PROCEDURE The are-cast molybdenum sheet used in this investigation was obtained from the Climax Molybdenum Co. of Michigan. It was 0.060 in. thick by 10

Jan 1, 1964

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.' The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By J. D. MacKenzie

THE world production of copper for the first eight months of 1927 shows an increase of 3 per cent over the same period in 1926. Since February of this year, however, production has been considerably curtailed. The United States reduction in the last four months has been offset by the increased South Ameri-can and Belgian Congo production. The United States is now producing 58 per cent of the world production, Chile and Peru 17.3 per cent, Belgian Congo 5 per cent. In 1926 the United States produced 54 per cent, Chile and Peru 16.3 per cent, Belgian Congo 6.3 per cent. Production, Tons 1917-largest war year 1,580,000 1925 1,581,000 1926-increase 3 per cent 1,628,000 1927-increase 3 per cent 1,670,000 Copper Producing Countries, 8 mo., 1927: Tons Per Cent United States 644,000 58.0 Chile and Peru 192,000 17.3 Europe 90,000 8.1 Belgian Congo 56,000 5.0 Japan 46,000 4.1 Mexico 30,000 2.7 Canada 23,000 2.1 Figures are not available for Spain and Portugal, which would probably precede Mexico.

Jan 12, 1927

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid binary and ternary Fe-Ni-Co alloys has been measured by the Sieverts&apos; method between 1550°and 1700°C. Solubility data and standard free energzes and enthalpies of solution for nitrogen in the alloys are presented. Interaction parameters are discussed and presented for binary and ternary alloys. MOST of the studies of nitrogen solubility in liquid metals have been directed toward the dilute alloys of iron. Several of these investigations have included measurements of the nitrogen solubility in Fe-Ni al10s&apos;- and in Fe-Co alloys.435 There has been some work, however, that has extended across the e-i-" and F-CO" binaries. This investigation was undertaken to determine the nitrogen solubility in both binary and ternary alloys of the Fe-Ni-Co system. It was also hoped that the differences between earlier studies might be resolved. EXPERIMENTAL METHOD This investigation was made using a Sieverts&apos; apparatus described previously." The nickel (99.85 pct) and cobalt (99.9 pct) were obtained from Sherritt-Gordon Mines, Ltd., and the iron (99.95 pct) was Fer-rovac-E obtained from Crucible Steel Co. Recrystal-lized alumina crucibles were used throughout the entire investigation with no evidence of crucible-melt reaction. Melt temperatures were measured with an optical pyrometer and the temperature scale calibrated against the melting points of the three pure metals. The emissivity of the melt was assumed to be a linear function of composition for all alloys, as has been shown for Fe-Ni alloys.lZ The emissivity of the pure metals at 1600°C were taken as 0.43 for iron, 0.44 for cobalt, and 0.45 for nickel. Using these emissivities, the trans mis sivity of the system was found to be 0.51 i 0.01. The Sieverts&apos; method was used for this study and followed the procedures outlined previously.l&apos; The individual metals were weighed to give about 100 g of alloy. The alloys were melted in the crucible under a partial pressure of argon. The system was evacuated, and the "hot volume" was measured with argon. To avoid the errors caused by vaporization, the melt was held under vacuum only long enough to ensure that all of the gas in the system had been removed. The influence of any small amount of vaporization on the "hot volume" was shown to be negligible by measuring the "hot volume" after a run. This measurement agreed with that made at the start of the run within the implicit error, 0.2 cc, caused by the limitations in accurately reading the buret. The solubility-pressure relationship was measured in the pure metals and in several alloy compositions throughout the ternary system. These measurements were made by admitting measured amounts of nitrogen to the system, and then determining the equilibrium nitrogen pressure above the melt. This method has the distinct advantage of higher accuracy, particularly at lower pressures, than measurements made by withdrawing gas from the system to reduce the pressure after determining the solubility at 1 atm nitrogen pressure. This latter method has a practical lower limit of about 0.4 atm where an increased error is encountered because the buret must be emptied to permit further measurements at lower pressures. By determining the relation between apparent solubility and pressure, it was possible to make a good estimate of the initial nitrogen content of the metal from the intercept of the solubility curve extrapolated to zero pressure.11 DISCUSSION The solubility data corrected to 1 atm nitrogen pressure are summarized in Table I. The reported solubility has been corrected for the initial nitrogen content of the alloys. The initial nitrogen contents fell between 0.0002 and 0.0010 wt pct, and were lower in the iron and nickel than in the cobalt. Sieverts&apos; law was obeyed in all alloys at pressures up to 1 atm. Examples of this behavior are shown in Fig. 1. The reaction for solution of nitrogen is Taking the standard state as 1 wt pct N in the alloy and the reference state as nitrogen at infinite dilution in the alloy, and noting the adherence to Sieverts&apos; law, K becomes the solubility of nitrogen in the alloy at 1 atm pressure. Thus the solubility data of Table I were used directly to calculate the standard free energy for the solution reaction. These results are also presented in Table I. The enthalpy of solution is also summarized in Table I as calculated from a form of the van&apos;t Hoff relation: Iron-Nickel System. The data for the solubility of nitrogen in liquid Fe-Ni binary alloys is presented in Fig. 2 along the with data of aito, Schenck et al.,&apos; and Humbert and 1liott.l&apos; The data for studies of nitrogen solubility in Fe-Ni alloys containing less than 20 pc t i&apos;- are not presented in Fig. 2, although they are in good agreement with the present work. The results of this study are in good agreement with Schenck

Jan 1, 1967

By W. C. Hagel

In 1952, Hauffe and pfeiffer1,2 reported that parabolic rates of nickel oxidation are decreased by factors of two and four at 1100° and 1000°C, respectively, when Li2O vapor is present. Hauffe &apos;s3 explanation was that monovalent lithium enters the crystal lattice of p-type NiO to decrease cation-vacancy concentration and, hence, diffusion of Ni2+ ions across the growing oxide. After first succeeding in adding lithium directly to molten nickel, the purpose of this investigation was to determine whether alloyed lithium is a more effective oxidation inhibitor than the external vapor. Seven 650-g heats were prepared by melting carbonyl nickel inductively under 1 atm of argon. Various amounts of lithium were added by dropping small chunks into the melt. Only about 10-pct recovery was achieved with the remainder lost by spattering and volatilization. Nominal and actual

Jan 1, 1965

By P. M. Kelly, E. P. Butler

The stability of a 70/30 Mn-Cu alloy aged to peak damping has been investigated using electron microscopy, X-ray diffraction, and torsional pendulum measurements. Storage at room temperature or at 100" C causes a reduction in damping capacity. This is shown to be due to the formation of subdomains which "lock" the main domain structure and so hinder their movement. After storage the damping capacity can be restored by a retransformation treatment, which generates structures identical to those found in newly aged specimens. Plastic deformation by rolling also causes a decrease in damping capacity. In this case the damping capacity can only be restored by retransformation if the amount of deformation is less than about 5 pct. THE general metallography and structure of these high damping capacity alloys has been discussed in Part I of this work.1 Part II deals with some of the variables that affect the damping capacity. In particular, the stability of the damping capacity of a 70/30 alloy aged for 2 hr at 425° C and quenched has been investigated. The temperature sensitivity of the damping capacity of a 70/30 alloy aged for 2 hr at 450° C has been reported by Birchon.2 The damping capacity begins to decrease with increasing temperature, and is very low above the M, temperature of 125°C. The cubic — tetragonal transformation is completely reversible and there is no apparent thermal hysteresis associated with the change in damping capacity. Another important effect was first reported by Dean and his coworkers.3 They noticed a decrease in the damping capacity with time for specimens of a quenched tetragonal alloy. More recently workers at the Admiralty Materials Laboratory 4 have studied the stability of an aged 70/30 alloy. They found that the damping capacity decreased to half its original value after about 1000 hr at room temperature. EXPERIMENTAL The techniques used for electron microscopy and X-ray diffraction have been described in Part I. The damping capacity was measured by means of a torsional pendulum, using rectangular specimens, 3 by 0.3 mm with a 6 cm gage length. The specific damping capacity, S.D.C., was calculated as a percent amplitude decay in free vibrations over 10 cycles, starting at an amplitude which corresponded to a 700 psi surface shear stress. Because of the stress dependence of the damping,&apos; the values obtained were about a third those reported for a 5000 psi surface shear stress.&apos; RESULTS a) Effect of Aging Temperature. The effect of aging temperature on the damping capacity is shown in Fig. 1. The damping capacity reaches a peak of 12 pct after aging at 400° to 425°C) then begins to decrease as the volume fraction of a Mn increases. At higher aging temperatures the structure becomes cubic again with a low damping capacity. b) Stability of the Aged Structure. The damping capacity of the aged alloy decreases with time at room temperature. This process could be accelerated by storing at 100°C, when about 100 hr were required for the damping to fall to half its original value. The results of room temperature and 100°C storage, for times up to 1000 hr, are shown in Fig. 2. The damping capacity starts to decrease after about 24 hr at 18° C and 1 to 2 hr at 100°C. It was found, however, that the damping could be almost completely restored by retransformation. The specimens were held at a temperature above the M, for a short time, 250° C for 5 min, and then quenched. The values of damping capacity for specimens that were aged, stored, and then retransformed are shown by the full points in Fig. 2. X-ray measurements of the c/a ratio and hardness readings on the specimens did

Jan 1, 1969

By M. N. Pathasarathi, P. A. Beck, T. J. Koppenaal

EARLIER work1 indicated that in rolled and annealed copper the volume fraction of the cube-texture component may increase on continued isothermal annealing. Merlini found2 that in rolled copper the well-known increase in the amount of cube-oriented material with increasing annealing temperature3 is concurrent with grain growth, which takes place after recrystallization is complete. It was found that both in copper2 and in aluminum4 the texture resulting from primary recrystallization, even if this is followed by some grain growth, may in general comprise, in addition to the cube-texture component, four symmetrical texture components of the general type (123)[412], i.e., components not very far from the ideal orientations of the rolling texture. The volume fraction of the cube-texture component increases on further annealing at the expense of these four components.&apos; The present work was undertaken to study quantitatively the increase in the volume fraction of the cube-texture component in the course of normal grain growth, under varying conditions. Since the grain-gr3wth behavior of A1-Mn alloys has been already investigated in some detaiL5 an A1 + 0.8 pct Mn alloy was chosen for this work, in which the extent of normal grain growth can be effectively controlled by the inhibiting effect of a dispersed second phase. EXPERIMENTAL PROCEDURE High-purity aluminum of the following composition was used: A1 99.997 pct, Cu 0.0004 pct, Fe 0.0005 pct, and Si 0.001 pct. A high-purity A1-Mn master alloy was prepared by dehydrating manganese chloride at 500°C and reacting it with molten high-purity aluminum at 750°C in a graphite crucible.5 The Mn metal reduced from the salt by the molten aluminum goes into solution in the latter. The master alloy? containing 13 pct Mn, was solidified under conditions suitable for minimizing segregation. An ingot of the final alloy, to be used in the experiments, was per pared by melting high-purity aluminum and the necessary amount of master alloy in a graphite crucible, and by pouring the molten alloy into a graphite mold preheated to 700°C through a box containing graphite baffles designed to intercept most of the aluminum oxide films floating in the melt. The melt was then solidified by placing the mold on a water-cooled copper plate and by keeping the top of the mold hot, in order to minimize piping. The 6 1/2 in. long, 11/4-in.diam ingot consisted largely of a single crystal. Chemical analysis showed that there was little segregation from the bottom (0.83 pct Mn) to the top (0.81 pct Mn). Spectrographic analysis of the ingot showed that the impurity content remained essentially the same as that of the aluminum used. The ingot was processed so as to obtain a uniformly small grain size. without banding. The ini-tial steps of rolling in the form of a flat bar and of annealing, down through a thickness of 0.4 in., are shown in Table I. At this point the bar was cut into four sections, each approximately 3 in. long, which were processed separately as shown in Table If. The table also gives the penultimate grain sizes obtained in each section by annealing prior to the final rolling of 90 pct RA. During the final rolling the strips were reversed end to end between passes. Annealing treatments were given in a salt pot furnace, with the temperature controlled to 1°C. All annealing of section "6s" was carried out above the solvus point to avoid the formation of second-phase precipitate. The penultimate annealing was sufficiently short to give a relatively fine grain size in spite of the high temperature. Section "6L" was processed in a similar manner, except that the penultimate annealing was much longer, so as to allow considerable grain growth. Section "4" was given the two final

Jan 1, 1961

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.&apos; These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf&apos;s associated with permeable formations are now understood to consist of liquid-junction emf&apos;s and membrane emf&apos;s.&apos;,&apos; As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf&apos;s just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.

By J. Henry Harden

I DESIRE to call the attention of the Institute to a new form of drawing-board trestle. With the ordinary four-legged trestle, commonly used, one has not the means of adjusting the height of the board to the draughtsman. To obviate this inconvenience, and at the same time to enable one to incline the board, I have devised an arrangement of curved and straight slots and thumb-screws, by means of which the board can be raised three or more inches, and placed at any desired angle of inclination on either side. Figures 2, 3 (Plate I) show side and end elevations of the trestle for a single board, and Figure 4 for two boards. The latter form is adapted for use in schools, or where it is desired to economize space.

Jan 1, 1874

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant&apos; have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh&apos;s work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-&apos; and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.&apos;, &apos; Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds&apos; of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies&apos; of the slags, slag weights, the metal particle theory,&apos; ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat&apos; is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By J. Henry Harden

I desire to call the attention of the Institute to a new form of drawing-board trestle. With the ordinary four-legged trestle, commonly used, one has not the means of adjusting the height of the board to the draughtsman. To obviate this inconvenience, and at the same time to enable one to incline the board, I have devised an arrangement of curved and straight slots and thumb-screws, by means of which the hoard can be raised three or more inches, and placed at any desired angle of inclination on either side. Figures 2, 3 (Plate I) show side and end elevations of the trestle for a single board, and Figure 4 for two boards. The latter form is adapted for use in schools, or where it is desired to economize space.