Search Documents

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. '162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653'C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By H. Conrad, V. V. Damiano, G. J. London

The slip mode activated during the c axis compression of single crystals of commercial-purity ingot SR beryllium, high-purity (twelve-zone-pass) beryllium, and Be-4.4 wt pct Cu and Be-5.2 wt pct Ni alloys in the temperature range of 25° to 364°C was determined using two-surface slip trace analysis, slip-step height analysis, and electron transmission microscopy. All three techniques indicated the occurrence of copious pyramidal {1 122) (1123) slip in the alloys over the entire temperature range, the amount increasing with temperature. Pyramidal slip was also indicated in the high-purity beryllium by slip trace analysis and electron transmission microscopy, but the amount was somewhat less than in the alloys. For the commercial-purity ingot crystals, only a very small number of pyramidal slip lines were observed, and these were in the immediate vicinity of the fracture surface. No pyramidal dislocations could be detected by electron transmission microscopy in this material. Dislocatransmissiontions with Burgers vectors [0001] and +(ll20) were identified by electron transmission microscopy inthe (1122) slip bands, as well as those with the j (1123) vector. This was interpreted to indicate that the edge components of the 3(1123) vector dislocations activated during c axis compression dissociate upon unloading according to the reaction i (1123) — [0001] + 3(1120) THE microstrain c axis compression of single crystals of commercial-purity ingot SR beryllium (99.6 pct), high-purity twelve-zone-pass beryllium (99.98 pct), Be-5.24 pct Ni and Be-4.37 pct Cu alloys was described in a previous paper.1 This paper covers in detail the analysis of slip traces observed on two mutually perpendicular lateral surfaces of these specimens, and a detailed description of transmission electron microscopy studies performed on foils cut from the bulk crystals after they had been deformed to fracture in the c axis compression. Observation of slip traces on single surfaces of deformed single crystals are generally insufficient to positively identify slip or twinning modes. The use of two carefully cut and oriented perpendicular surfaces can greatly aid in the positive identification and index- ing of slip traces, although even this technique may be quite inadequate if more than one type of slip system operates and if an insufficient number of traces are observed on the surfaces. The problem is greatly simplified for symmetric cases like that for c axis compression of an hep crystal such as beryllium, in which the operating slip systems are all equally inclined to the direction of the applied stress, and each slip system of a given slip mode has an equal chance of operating. For such cases, the traces of any given slip mode observed on the surfaces cut parallel to the c axis are symmetrically tilted about the c axis. It is therefore possible to quickly determine whether one or more slip modes are operating. Confirmatory evidence in support of the observations made on the external surfaces can be obtained from foils cut from the deformed crystals and examined by transmission electron microscopy. This latter technique serves to identify not only the operating slip plane but also the Burgers vector of the dislocations which participate in the slip. For this purpose, a simplified technique based upon a double tetrahedron notation is used in the present paper. The planes and directions in the hep lattice are all designated by letters rather than indices and extinction conditions are easily determined if the Burgers vector lies in the plane contributing to the diffraction. RESULTS 1) Slip Trace Analysis. The standard (0001) stereo-graphic projection of beryllium is shown in Fig. 1. The two mutually perpendicular, lateral surfaces of the compression specimen are represented by the diametrical planes AA' and BB', also referred to as surface A and surface B. For the specific case represented (a Be-5.24 pct Ni specimen deformed by c axis compression at room temperature), the A surface is tilted 5 deg to the (10i0') plane and the B surface is tilted 5 deg to the (1120) plane. Two surface trace analyses may be facilitated by examining in turn the intersection of various great circle traces of specific pyramidal planes with two surfaces and comparing the angles made with the (0001) plane with those actually observed on the two surfaces. One then identifies the slip traces by trial and error on a best-fit basis. The (1122) type planes (it was found that slip occurred on these planes) are shown plotted on the stereographic projection in Fig. 1. One obtains directly the angles between the (0001) plane and the {1122) traces by measuring the angle from the periphery to the point of intersection along the lines

Jan 1, 1969

By Stuart Croasdale

Not long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale. Temperature, Degrees F. High Low Average June...................... 112 62 84.0 ' July...................... 115 71 87.8 Evaporation June July Concrete tank, inches............ 11.7 10.72 Iron tank, inches.............. 14.8 13.07 Rainfall, inches................ None 0.77 Cloudy days................... None 10.00 Aside from several springs about 10 miles from the property, the nearest known water in quantity at the time these experiments were made was the Gila river at Gila Bend, 45 miles distant. Part of the developinent of the property of course included drilling for water in the valley, which was in progress at the conclusion of my experiments. The ore deposit itself is unusual. It consists of of intrusive plug of monzonite or granite porphyry. Chalcopyrite, bornite, and magnetite are finely disseminated throughout the magma in sufficient quantities to make the greater part of the mass commercial ore to a certain depth.

Jan 1, 1915

By M. C. Leverett, M. E. True, W. B. Lewis

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By W. B. Lewis, M. E. True, M. C. Leverett

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By W. P. Shinn

In a paper contributed by W. A. Goodyear, M.E., on "Water Gas as Fuel," read at the Boston Meeting, February, 1883,* the following statenlent was made: "The latest experiments on a scale of some magnitude in our citier, in the way of heating buildings and furnishing power for manufacturing purposes, have been by the distribution of high-presslire steam through pipes laid in the streets. Hilt these experiments (1) have not hitherto been very successful; and when we consider the high cost and (2) the great and unavoidable loss of heat and power, which always accompany the conveyance of high-pressnre steam to any considerable distance in pipes, to say nothing of (3) certain practical difficulties in the management of the pipes themselves, (4) it is evident that all such methods must eventually disappear before a system which can furnish a cheap gas of great heating power, easily distributed wherever wanted, without requiring pipes to stand pressures of 50 to 75 pounds per square inch, and (5) without keeping the whole mass of ground in the streets through which it passes hot, gratis, for a distance of ten or fifteen feet, in all directions around the pipes!&apos; For the purpose of controverting Mr. Goodyear&apos;s statements in regard to steam-distribution in cities, I hare numbered the points made in his indictment, my principal object being, not a professional discussion of the technical and theoretical merits of steam vs. watergas, but a simple statement of facts, in regard to the present state of the street system of steam distribntion. Taking Mr. Goodyear&apos;s points in their order: 1. Concerning what he terms " These experiments," saying that they " have not hitherto been very successful," I propose to show, that the problem of stearn-distribution has passed beyond the experimental stage, and that its practical solution is highly successful. This will be shown by the facts hereinafter fully set forth. 2. "The great and unavoidable loss of heat and power whicn always accompany the conveyance of high-pressure steam to any con-

Jan 1, 1884

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By R. L. Frink

I FEAR that my treatment of this subject may not, in all instances, meet the approval of those who read my opinion as to the utility and efficiency of pyrometers in the making of glass, or bottle-glass. It may be superfluous for me to add that this opening statement is based on over 15 years&apos; experience in an endeavor to successfully apply pyrometers, or heat-measuring instruments, to glass-melting furnaces, particularly the type known as tank-furnaces, and that such endeavors have proved more or less futile. It is my desire, therefore, to herein set forth the problems encountered, hoping thereby to stimulate further effort in the successful application of pyrometers. It is my desire, also, to invite criticism of the methods used and suggestions from those who may have a wider experience, or who may have better methods. Fin. 1.-GLASS TANK FURNACE. In general, I believe that the inefficient application of pyrometry to the melting of glass in tank furnaces is not due as much to the instruments as to the conditions under which they must be used and the character of the medium in which they must reside. Most of those present no doubt, are familiar, at least in a general way, with the methods and apparatus used in the melting and making of bottle-glass, or glass that is formed into containers of various shapes and designs. Most of this glass is made in what is known as a tank furnace, these furnaces vary widely in design and construction. In general, they consist of a rectangular tank-like form, built up of fireclay blocks, and range from 2 by 4 ft. (0.6 by 1.2 m.) to 24 by 140 ft. (7.3 by 42.6 m.) with a depth of glass from 2 to 5 ft.; or a capacity of from approximately. 2 to 700 tons. Fig. 1 shows the general

Jan 9, 1919

By R. C. Hyslop

THE object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: I. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. The equipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. LABORATORY PROCEDURE With these ideas in mind, the problem was approached in the manner in which Koenigsberger1 developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change [ ] in the magnetic field intensity due to the proximity of a specimen is given by: [ ] Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. I.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1941

By Myron K. Rodgers

In rock- or ore-crushing tests all data, in order to be valuable for study and comparison, should be obtained and tabulated under conditions as uniform as possible. The results of many such tests have no value for comparison, because of incomplete data and the lack of uniform conditiops, screens and scale of sizing, etc. The purpose of this paper is to suggest a form of standard specifications which may be developed by the Milling Committee and approved by the A. I. M. E. for rock-crushing tests. It is not intended to discuss any theories of rock crushing. Reports of rock-crushing tests should include the following details: 1. Description of the machine employed (jaw or gyratory crushers, rolls, stamps,tube mills, Chilean mills, etc.), 2. Method and material (timber, concrete, etc.) of foundation. Much power is dissipated in the vibration of poor foundations. 3. Locality from which the rock or ore was obtaincd, and geological, mineralogical, and physical characters of the material. 4. The power consumption of the machine running with no load and with full load, the unit of power being 1 hp. per 24 hr, 5. The capacity of the machine in tons (of 2000 Ib.) per 24 hr. 6. The duty in tons per horsepower-day. 7. The screen analysis of feed and product by the proposed A. I. M. E. standard screen scale. On the foregoing statement, the following remarlrs are offered. Toughness of Rock Table P shows the relative crushing duty of the same machine on three different characters of rock, all other crushing conditions being the same. This table indicates that the specific resistance of the rock to crushing, may affect the crushing duty of a unit of power as much as 300 per cent. Perhaps this quality may be called toughness. It is not a function of hardness only. For comparison of tests, rocks should be divided into

Jan 1, 1916

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962

ALABAMA Aldrich.-Lloyd, T. W. Ashland.-Downs, F. G. Geary, E. S. Auburn.-Brown, R. L. Bessemer.-Abbott, C. E. Ball, T. L. Ferguson, V. Salmon, H. S. Stuart. Q. W. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Armstrong, W. D. Ball, E. M. Bonnyman, J. Bush, M. W. Crawford, G. G. Davis, C. B. Ellis. E. E.

Jan 1, 1923

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,&apos; in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20&apos; to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200&apos; and 250°C. (392&apos; and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures&apos; The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,&apos; in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20&apos; to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200&apos; and 250°C. (392&apos; and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures&apos; The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946