Search Documents

By J. L. Taylor, P. Duwez

PARTIAL phase diagrams of titanium with iron, cobalt, and nickel have been established by previous investigators.1-3 These diagrams seem to be reliable, at least for concentrations of titanium ranging from 0 to about 50 at. pct. More recently, Long and his collaborators have presented a tentative titanium-nickel diagram covering the titanium-rich side.' These various studies indicate that in each system three intermediate phases exist and correspond to the compositions Tia, TiX, and TiX2 (or TiX3). The purpose of this paper is to review the available information on the crystal structure of these phases and to give the results of additional X-ray diffraction studies. Previous Work A summary of the work of Wallbaum and his collaborators"-' is presented in table I. The first intermediate phase on the titanium-rich side of the three systems, with iron, cobalt, and nickel, is of the Ti2X type and has a face-centered cubic structure. Although it is stated that the unit cell contains 96 atoms: no lattice parameters are given. The second phase is centered around the compositions TiX for the three systems. The crystal structure of this phase is mentioned in a short note" as being body-centered cubic (CsCl type), but no parameters are given. The analogy between the three systems, which is perfect as far as the two phases of the type Ti2X and TiX are concerned, disappears at the titanium-poor end of the diagrams. In the system titanium- iron, TiFe2 has an hexagonal (MgZn2 type) struc-ture with the parameters given in table I. The existence of TiFe3 has also been reported8 (table I) but was questioned by other investigators2 and is also refuted by the present study. In the system titanium-cobalt, a phase corre-sponding to the composition TiCo2 has been investi-gated by Wallbaum and Witte6 who claim that the structure is cubic (MgCu2 type) for alloys slightly deficient in cobalt and hexagonal (MgNi2 type) for alloys slightly deficient in titanium. The parameters of the two phases are given in table I. In the system titanium-nickel, the nickel-rich phase corresponds to the composition TiNi3 and has been described as hexagonal7 with the parameters given in table I. The present investigation was initiated for the purpose of filling in the gaps in the knowledge con-cerning the structure of the various phases sum-marized in table I. Since the titanium used by Wallbaum and his collaborators was only 95 pct pure,' it was found desirable to redetermine the lattice parameters of the alloys prepared with a

Jan 1, 1951

By THOMAS G. FEAR

THE COAL DIVISION started its share of the annual meeting Monday morning with a study of coal classi fication. A. C. Fieldner was in the chair. The report of the tellers of the ballot for division chairman, stating that Thomas G. Fear had been elected to that office, was read by M. D. Cooper. Mr. Fear acknowledged the honor in a few words. In reviewing the history of the Coal Classification Committee the chairman pointed out that this was its third symposium, the last previous one having been held at the 1930 Annual Meeting. Throughout its work the com¬mittee has had the active cooperation of the Canadian workers who are interested in the subject which should result in a uniform scheme of classification in Canada and the United States. F. E. Lathe, of the National Research Council, Ottawa, abstracted the first two papers of the session entitled "Determination of the Alkali-Soluble Ulmins in Coal," by Edgar Stansfield and K. C. Gilbart, and "Moisture Determination for Coal Classification," by the same authors. The third paper "Condition of Water in Coals of Various Ranks"' was presented by its author, A. W. Gauger. Written discussions of these papers were presented by H. C. Porter and Gilbert H. Cady. In the oral discussion which followed, W. T. Thom, Jr., brought out the advisability of considering age as a factor in classification. Mr. Fieldner favored retaining bed moisture as a partial classification basis, stating that a review of many coal analyses revealed a remarkable consistency in this item in samples from a given mine particularly where the moisture content was not high. Mr. Porter pointed out that the structure and porosity of coal often have much to do with its moisture content and that these vary in different parts of a seam, particularly in anthracite. Mr. Gauger expressed doubt as to whether the Stansfield method gives the true moisture content of coal, which is needed for classification purposes.

Jan 1, 1932

By George R. St. Pierre, John Chipman

METALLURGISTS have been studying the chem-ical behavior of sulfur in steelmaking for many years in order to have a better control of the sulfur content of finished steel. During the refining period in the open hearth, molten steel is separated from a gas phase by molten slag. Chemical reactions occur principally at the slag-metal interface and at the slag-gas interface. A need for physical-chemical investigations of reactions between sulfur-bearing gases and steelmaking slags was recognized some time ago.'.' From the early work, it can be qualitatively concluded that increased sulfur content and low partial pressure of oxygen in the gas phase favor the passage of sulfur from gas to slag. Using radioactive sulfur S Koch and Fink' have demonstrated the rapid rate of exchange of sulfur between gas and slag in an open hearth furnace. Gurry and Darken and Darken and Shields (as reported by Derge and Marshall') have equilibrated lime-iron oxide slags with SO—O2 gas mixtures. The major conclusion from the reported results is that sulfur content increases with increasing lime content in lime-iron oxide slags equilibrated with a gas of high oxygen pressure (10-2). The data were interpreted as indicating the presence of SO, and S,O, ions. Richardson and Fincham' have conducted the most extensive experimental study of sulfur equilibria between gas and slag. Their results confirmed many of the conclusions drawn from calculations of Richardson" and Withers. Richardson and Fincham's data fitted very well into the sulfur scheme represented by the reactions 1/2 s2 (g) + (0) melt - 1/202(g)+ (S) melt [II 1/2 S, (g) + 3/2 O (g) + (0) melt - (SO,) melt. [2] At oxygen pressures greater than 10 to 10 they found that reaction Eq. 2 was predominant while reaction Eq. 1 was controlling at oxygen pressures less than 10." to 10.". The slag compositions and gas mixtures used in their investigations were different from those used in the present study. Wherever possible, comparison has been made between their results and these, and agreement is excellent. It is evident that the distribution of sulfur between slag and gas depends upon the oxygen pressure of the gas. In FeO slags, a change in oxygen pressure produces a change in ferric oxide content, and a knowledge of this equilibrium is a prerequisite to studies of sulfur distribution. The data are found in the work of Darken and Gurry" on the FeO system and the more recent experiments of Gurry and Darken" and of Larson and Chipman" on FeO slags containing lime and silica. The effect of oxygen pressure on the ratio Fe /(Fe" + Fe ), the so-called j-ratio, reported by these investigators will be used in interpreting the results which follow. Experimental Method The purpose of the experimental program was to determine the equilibrium sulfur content in slags exposed to gases of known oxygen and sulfur pres- sures. The slag compositions selected for study were from the lime-silica-iron oxide system. Additions of magnesia were made to some of the slags. Apparatus—The apparatus used by Larson and Chipman was modified slightly to accommodate the addition of SO2 to the gas mixtures. As in their work, slag samples of 0.5 to 2.0 g were held at temperature (lcc) in platinum crucibles under a steady stream of gas, 100 to 200 ml per min, for several hours and then rapidly lowered to the bottom of the furnace where they were quenched in mercury. Preparation and Analysis of Gas Mixtures—Mixtures of SO,-CO were prepared from Virginia Smelting Co. Extra Dry liquid SO, and Pure Co. CO,. After removing traces of water vapor with an-hydrone, the CO, was passed over graphite at 1200°C, at which temperature the conversion to

Jan 1, 1957

By A. R. Powell

Four, general methods have been used in the study of the decomposition of coal. The first has been directed toward the processes of coal formation, the second has been by means of microscopic studies, the third from the data of destructive distillation, and the fourth has made use of various solvents. Applying these methods to the sulfur of coal, it has been found that the organic sulfur of plant and animal life enters into the formation of coal and remains in organic combination in the final product. The inorganic sulfur is almost entirely combined as iron pyrites and marcasite. The infiltration of hydrogen-sulfide waters is doubtless a large factor in these combinations. Sulfates are found in very small quantities except where free oxygen has entered the coal strata. The mechanical mixing of detritus with the early coal material is another source of sulfur. In this case the sulfur is distributed in microscopic particles throughout the mass. In destructive distillation, a part off the sulfur comes off as hydrogen sulfide and various thiophen compounds, but this furnishes little information as to the nature of the sulfur compounds in the coal itself. The use of solvents has given valuable data concerning the sulfur compounds in coal. Fremy1 and later E. Guignet2 noted the action of alkaline solutions on coal after treatment with nitric acid and Anderson and Roberts3 showed' the presence of large quantities of organic' sulfur in the extract so obtained. In a study of the phenol extract of coal, Parr and Hadley4 found organic sulfur in the soluble organic material. These investigations proved the presence of organic sulfur in coal in addition to the inorganic forms, such as iron pyrites and sulfates. T. M. Drown5

Jan 9, 1919

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

By M. P. E. Desvaux, P. Charsley

OLIP-line observations on copper alloys, using the electron microscope, have been made by a number of workers,13 but this work has been confined to a brass. In a CuAl alloys Koppenaal4 and Koppenaal and Fine5 have made observations with the optical microscope and by the use of interferometry. They found that the observed slip step heights inside the Liiders bands accounted for only 42 pet of the total macroscopic strain. The suggestion was put forward that optically unresolvable slip in other parts of the specimen accounted for a major part of the macroscopic strain. This is surprising since it is known from other workers that slip in a brass is inhomogeneous; i.e., large amounts of slip occur on individual {lll) closelys paced than being shared by a large number of closely spaced planes. Furthermore, a brass and a CuAl alloys with high concentration of aluminum exhibit similar deformation characteristics and slip-line patterns. Prior to investigations into the behavior of copper and a CuAl alloys under reversed stresses in tension and compression, some preliminary experiments have yielded results which the authors think resolve this discrepancy, and throw some further light on the behavior of a CuAl in tension. An experiment was carried out on a 10 at. pet CuAl single crystal, of gage length 7.5 cm, diameter 3.1 mm, and orientation shown in Fig. 3 (inset), for the purpose of resolving the above discrepancy. The specimen gage length was electropolished for 10 min in a 50:50 orthophosphoric acid (SG=1.75)-distilled water system, with 2 v across the cell and a current density of 0.5 amp per sq cm. The cathode was made of copper. After a tensile strain of 0.067 ± 0.001, intense slip was observed over a length 2 cm of the gage length whilst the rest of the specimen was relatively undeformed. In the lightly deformed region, slip bands of mean width 20 /x were spaced about 1 mm apart on average. The transition from the heavily slipped region (usually called a Liiders band) to the lightly deformed region was gradual, the slip-band density increasing as the "Liiders band" was approached. In the latter, the slip bands became so close together that, to the naked eye, the specimen appeared to be continously slipped, and the typical microtopography of this region is shown in Fig. 1. Twelve electron micrographs were taken at random from replicas of the Liiders-band region, and the widths of the slip lines were measured. The slip lines account for an over-all tensile deformation of 7.0 ± 0.7 pet, after allowing for the lengths of the un-slipped regions, which is in good agreement with the macroscopic strain. The distribution of slip-line widths was also measured and is shown in Fig. 3. Since Koppenaal could not resolve slip lines with height less than 540A (limit of resolution represented by dashed line), then it was deduced that he could have measured only about 50 pet of the deformation within the 'Liiders Band'. It is concluded, contrary to the suggestion of Koppenaal,5 that virtually all the macroscopic strain is accommodated within the "Luders band" and that there is no need to invoke fine slip distributed uniformly over the gage length.

Jan 1, 1967

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By R. G. O’Meara, M. M. Fine

ONE of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.[t] In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.1 The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 ACKNOWLEDGMENT This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. O. E. Anderson, mill superintendent,

Jan 1, 1946

By C. C. Templeton, J. C. Rodgers

A key step in feed water treatment for generating wet steam for thermal oil recovery is the removal of calcium and magnesiunt hardness by cation-exchange series softening. Knowing the solubility of any scale forming salts in brines at elevated temperatures is necessary for fixing the level to which the feed water must be softened. Such calcium sulfate solubility data, previously not available above 392F, were determined by the authors in a flow equilibrium apparatus mud will be reported elsewhere. These data were used to develop a method for predicting the solubility of anhydrite in hot water or steam droplets for saturated steam pressures as high as 2,000 psig (637F). (The calcium sulfate solubility product is represented by a combination of two factors, one reflecting the effects of ionic strength and the other accounting for the effects of complex ion formation in either calcium-magnesium-rich or sulfate-rich brines.) The method is applied to a calcium-magnesium-rich brine If moderately high salinity from a pilot hot-water flood, I nd to several sulfate-rich, low-salinity feed waters and l lowdown (cooled steam droplets) samples from steam s ak operations. The predicted calcium hardness levels corresponding to the calcium sulfate solubilities agreed reasonably well with the results of laboratory solubility determinations run on the field samples. Further testing of the method is needed for brines of other composition classes. Existing field cation exchange softeners in the cases tested are performing adequately since all the samples were found to be undersaturated with respect to calcium sulfate at their operating temperatures. Introduction Prevention of scaling caused by precipitation of calcium sulfate (anhydrite) is of considerable concern in connection with thermal recovery processes using wet steam or hot water. To avoid anhydrite precipitation in a heated system, an engineer must keep the product of the calcium and sulfate concentrations in the water or steam droplets below the value of the solubility product of anhydrite for the temperature and brine composition in question. Usually it is most practical to keep the concentration product lower than the solubility product by keeping calcium low in the presence of high sulfate, or by keeping sulfate low in the presence of high calcium. This can be done by a choice of combinations of natural waters and water treatment processes (such as series cation exchange softening to remove calcium). Until recently, few anhydrite solubility data, particularly for solutions containing other salts, were available for temperatures above 392F (211 psig steam); Marshall, Slusher and Jones' studied the CaS0,-NaCI-H,O system up to 392F and surveyed the work of previous investigators. To model natural brines, one needs to study the solubility of anhydrite in aqueous solutions of sodium chloride, sodium sulfate, calcium chloride, magnesium chloride and their mixtures. Since steam pressures as high as 2,000 psig (637F) may be involved in thermal oil recovery projects, a solubility study was conducted between 482 and 617F.' Discussed in this paper is the application of these data to the prediction of anhydrite precipitation in some practical steam soak and hot-water injection projects. Any simple method for predicting the solubility of an inorganic compound over a wide range of temperatures and solution compositions must be based on some assumptions, and therefore must yield approximate results. On the one hand, natural brines contain too many ionic species for all to be included in a simple scheme; on the other hand, there is no adequate theoretical basis for the exact prediction of solubility in even simple solutions of mixed electrolytes. However, it is possible at a given temperature to base a reasonable prediction scheme on two phenomena:'-' the increase in solubility with increasing total concentrations of all ions (as measured by the ionic strength; see the Appendix), and an increase due to formation of cornplexes between calcium ions and sulfate ions and between sulfate and magnesium ions. Stiff and Davis' developed such a scheme for predicting the solubility of gypsum (CaSO, ¦ 2H,O) in brines at temperatures u~ to 212F. However, for the higher temperaturei of present interest, the stable solid phase is anhydrite (CaSO,). This study involves a two-part method for predicting anhydrite solubility products. First, one predicts a value K, for a given ionic strength I and a given temperature T corresponding to mo./msr, = 1 from data of the CaS0,-NaCI-H,O system. Second, one determines a group of factors F .= F(Ca) • F(Mg) • F(SO,), where the individual factors account for increases in the solubility product due to complex formation by high concentrations, respectively, of calcium, magnesium and sulfate. Combining the two parts, one obtains the solubility product in molalities as

Jan 1, 1969

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By W. R. Hibbard

T has been proposed1 on the basis of slip and flow I- that the ideal deformation texture of cold rolled face-centered cubic metals is (110) [112]. As pointed out recently by Brick,' this theory does not account for the difference between the pole figures for cold rolled copper and 70-30 alpha brass, which develop strikingly different spreads from the ideal orientations. It does suggest that the pole figures might be similar for these two metals if they are rolled sufficiently. This has been found to be the case for cold drawn wire.' Experimental Procedure: Four inch sections of cast cakes of copper and 70-30 alpha brass were obtained through the courtesy of the Bridgeport Brass Co. Pieces from these cakes were cold straight rolled 99.993 pct reduction in thickness with the assistance of the Remington Arms Co., Bridgeport, Conn., and by the use of pack rolling. Pole figures were made using the X ray camera and techniques described by Brick.' These pole figures were not significantly different from those previously published for the same materials rolled 98 pct. Eight thicknesses of this strip were then pack rolled. This material failed completely and extensively in tension as shown in fig. 1, developing wavy transverse fractures and bulges. No further work could be done on these samples. Summary: Within the range of this experiment, no attainable amount of cold rolling would cause the pole figures of cold rolled copper and 70-30 brass to become similar, in spite of the fact that such a similarity is predicted by theory.' References W. R. Hibbard. Jr. and M. K. Yen: Trans. AIME (1948) 175, 126. Met. Tech. Feb. 1948. TP 2334. ²R. M. Brick: Trans. ASM (1949) 41A, 99. 3W. R. Hibbard, Jr.: Trans. AIME (1949) 185, 598, Jnl. of Metals, Sept. 1949. "R. M. Brick: Trans. AIME (1940) 137, 193. 'R. M. Brick, D. L. Martin and R. P. Angier: Trans. ASM (1943) 31, 675.

Jan 1, 1951

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By Klaus Schwerdtfeger, Hans-Jürgen Engell

Activities of silicon in Ni-Si melts have beelz determined in the temperature range 1480° to 1610°C from electromotive-force measurements involving the cells The data obtained are used to derive the activities of nickel and the integal free energies of mixing. Entropies of mixing are calculated from the free energies of mixing as obtained in the present study and the heats of mixing as available in the literature. ACTIVITIES in Fe-Si and Co-Si melts have been determined recently by the authors&apos; using galvanic cells consisting of alloy, an oxygen electrode, and an oxide melt as electrolyte. The present paper deals with activities in Ni-Si melts as measured with the same technique. A schematic diagram of the cell is shown in Fig. 1. The alloy and the electrolyte consisting of CaO and SiO2 are contained together in a silica-glass crucible. During the experiment the silica glass crystallizes to cristobalite on the surface of the crucible. Nickel contents of the electrolyte are very small (<0.1 pct as checked with chemical analysis), because of the noble character of nickel in comparison with silicon. A tapered silica tube is connected to the crucible through which a platinum or molybdenum wire is inserted, as shown in Fig. 1. A platinum tube reaches the surface of the CaO-SiO2 electrolyte from above. The platinum tube is provided with four holes on its side, through which oxygen of 1 atm pressure is blown over the electrolyte. The cell reaction is given by the equation Si(metal) + O2(gas) = SiO2(electrolyte) [3] and the galvanic electromotive force of the cell is given by the formula

Jan 1, 1965

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7&apos;e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,&apos; and Owen has started some detailed studies with a carbonyl system.&apos; A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4&apos;5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941