Search Documents

THE total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: BARRELS BARRELS (42 GAL.) (42 GAL.) North Sumatra 4,226,935 Ceram 326,207 South Sumatra 13,956,157 Sarawak 2,739,650 Java 3,845,568 Brunei 1,322,725 Dutch Borneo (main island) . 9,406,733 Dutch Borneo (Island of Tara- kan) 6,579,184 Total 42,403,159 Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numer-ous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths. up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a depth of 2332 m. (7650 ft.) before abandon-ment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin.

Jan 1, 1933

By Charles Y. Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders % in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: CoMPressiON, Average Length, Series Pounds Inches 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series consisted of 17 specimens lettered 0, B, C, D, E, F, G, H, I, J, K, L, M, N, P, Q and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for 1/2 hr. at the following temperatures: TEmpeRa- TempeRa- Letters tuRe,° C. LettERs tuRe °C. B............................... 250 J.............................. 650 C............................... 300 K............................. 700 D............................... 350 L.............................. 750 E............................... 400 M............................. 800 F................................ 450 N............................. 851 G............................... 500 0. . :........................... 900 H............................... 550 P.............................. 950 I................................ 600 Q............................. L000

Jan 1, 1926

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation's C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation's C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940

By R. A. Vandermeer, J. C. Ogle

Two distinct types of depth-dependent variations in texture have been observed in niobium cold-rolled various amounts up to 99.5 pct reduction in thickness. These nonuniformities are thought to be the results of nonhomogeneous plastic dewmation during rolling. The first type is characterized by a zone at intermediate depths that tends to lack certain strong orientations which are present in the surface and center layers of the rolled stock. This type of texture modification seemed to be associuted with "high" body rolling and may be related to the shape of the zone of deformation in rolling. The second type of texture inhomogeneity found involved the formation of a unique texture in the surface layers of heavily rolled strip. High fiiction forces between work piece and rolls appear to be needed to generate and maintain this texture. We believe that this unique surface texture results from a shear mode of deformation in the surface layers. THE evolution of texture in both the surface and center regions of cold-rolled niobium as a function of increasing deformation from 43 to 99.5 pct reduction in thickness was reported in a previous paper.' It was noted that for strips rolled between 95 and 98 pct reduction a distinctly different texture appeared in the surface layers which was unlike the center texture. Certain other layer to layer textural variations were also detected during the experimental phase of that work but were not described in the paper. Surface textures have been reported previously for the bcc materials iron and Steel2-4 and are well known in the fcc metals.5 It is usually stated that these are shear textures which arise under conditions of high friction between specimen and rolls. Work by Mayer-Rosa and Haessner5 n niobium rolled under conditions presumed to be high roll friction gave no indication, however, of a surface texture in that material. This is indeed puzzling in view of our results.' Thus we undertook additional experiments designed to study the stability of the surface texture for certain rolling variables. The variables investigated were the presence or absence of lubrication, amount of reduction per pass, and reverse vs unidirectional rolling. It is the purpose of the present paper to describe the kinds of depth-dependent textural inhomogeneities that we have observed in rolled niobium as well as to present the results of our recent experiments on the stability of the surface texture. Possible explanations for the depth-dependent texture variations will be discussed in terms of nonhomogeneous plastic deformation during rolling. EXPERIMENTAL Specimens cut from the niobium rolled to different reductions in the previous study1 were examined at various layer levels throughout the strip thickness for textural inhomogeneity. The specimen surfaces were either etched or machine ground and etched to remove material to a specific depth. Textures were determined by means of the Schulz X-ray reflection pole figure method with a Siemens texture goniometer and Cum X radiation. Since the important intensity peaks of the textures in niobium are usually located on the normal direction (N.D.) to rolling direction (R.D.) radius of the (110) pole figures, it was sufficient in many cases to scan only along this radius. At selected depths or where additional information was required the entire (110) pole figure was also obtained. In studying the stability and formation of the surface texture, experiments were conducted on 0.400-in.-thick, fine-grained, randomly oriented niobium specimens extracted from the same starting stock as that used in the earlier study.' Two of these specimens were rolled at room temperature to a total reduction of 96.4 pct. One was rolled between cleaned and degreased rolls with no lubrication. The other was lubricated between passes with Welch Duo Seal vacuum pump oil. The rolling schedules of each were kept as nearly identical as possible. Drafts were of the order of 0.006 to 0.012 in. per pass. Other experiments consisted of rolling specimens at constant fractional reduction per pass, i.e., (ta- tb)/ta equals a constant where ta and tb are the entrance and exit thickness of the rolled stock, rather than at a constant draft, i.e., ta- tb equals a constant. Ten specimens were rolled at room temperature on a two-high, motor-driven rolling mill with 8-in.-diam rolls. These specimens were rolled to thicknesses of between 0.041 and 0.073 in. (82 to 90 pct total reduction) at approximately constant reductions per pass ranging from 9 to 45 pct. Kerosene was used as a lubricant. Half of the specimens were always rolled in the same direction while the other half were reversed end to end at each pass. The texture in the surface regions was determined with the X-ray technique described above. RESULTS The textural inhomogeneities noted in niobium rolled from fine-grained, randomly oriented stock 1.5 in. long by 0.75 in. wide by 0.40 in. thick can be classified into two types. The first may be discussed with the aid of Figs. 1 to 3. Fig. 1 is a three-dimensional plot of the X-ray intensity in units of times random vs f , the angle from the N.D. to any point along the N.D. to R.D. radius of the (110) pole figure, and depth, given as percent of the thickness (?t/to X 100, where at is the thickness of material removed and to is the as-rolled

Jan 1, 1970

AT the Tulsa meeting of the A. P. I., the following reso-lutions, expressive of the policy of that organization, were among those adopted: RESOLVED, That we endorse the conclusion of the Federal Oil Conservation Board in its report of September, 1926, that the prevention of the waste of gas incident to the pro-duction of oil is of paramount importance in the conserva-tion and economical production of oil, and the president of the Institute is requested to appoint a committee of seven to devise and suggest to this board, or the executive com-mittee, such measures as will enable the industry, while continuing to meet the consumption requirements for pe-troleum and its products, to conserve in its natural state such reserves of petroleum as may not then be required for consumption. RESOLVED, That the president of the Institute appoint a committee of seven to formulate and recommend to this board or its executive committee, at the earliest practicable date, a program of legislation; Federal and State, to be advocated by the Institute giving sanction and effect to agreements by oil producers for the curtailment of produc-tion in pools where and during periods when there is over-production, having for their purpose the economical and orderly production of oil.

Jan 1, 1927

By David J. Dunn

At a time when mill availability is at a premium, production costs are rising, and lead time for mill liner casting is a year or more, mill liner design is an important factor in ore grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, reduce liner wear rate, and lengthen liner life. The mill liner that grinds best, lasts the longest, and costs the least is a necessity for economic mill operation. After testing four mill liner profiles for 3.96 X 3.65-m (13 x 12-ft) overflow ball mills, Climax Molybdenum Co. found that an improved design increased mill tonnage by 2.72 t/h (3 stph) while reducing finish grind by 1.7% minus 100-mesh, reduced liner wear rate, and almost doubled liner life.

Jan 12, 1976

By Sidney G. Parker, Jack E. Pinnell

Cubic ZnSe crystals have been grown with HCl, HBr, and I, as chemical transport reagents. The growth of large, well faceted crystals is in the order HCl < HBr < I, with some produced by I, transport being 1 cm on an edge. ZnSe:I crystals showed no strain in cross polarized light and were homogeneous as determined by electron microprobe. These ZnSe:I crystals had a mobility at 25°C of about 300 sq cm per v-sec and contained 103 dislocations per sq cm; further, these crystals were pure cubic and showed both photolumi-nescence and photo conductance. Doping was attempted during crystal growth. ZnS and Zn (S,Se) crystals were also grown by I, transport. ZnSe crystals have been grown by most of the common techniques.1"6 Of these, chemical vapor transport as developed by Kaldis2 showed promise of producing high perfection, cubic ZnSe. With chemical transport, crystals can be grown far below the transition temperature for conversion of cubic to hexagonal structure. A small temperature gradient between source and growth region tends to allow near equilibrium growth, which should lead to good crystalline perfection. Because it is necessary to form volatile compounds, halogens or their compounds are extensively used as transport agents. HCl, HBr, and I, were compared as transport agents for growth of ZnSe crystals. Doping during crystal growth was attempted. ZnS and ZnSxSe1-x crystals were also grown by chemical transport. Electrical and optical properties of the crystals were examined. EXPERIMENTAL Fig. 1 is a sketch of the growth apparatus, which was a modification of Kaldis&apos;. A quartz rod which butted against the seed crystal served as a heat sink to promote growth only on the seed. Initially, crystal growth was attempted with ZnSe prepared by wet chemical methods. Because such a material contained oxides and selenates, HC1 reacted with these oxygen compounds to form H2O and no ZnSe transport occurred. Further, this ZnSe contained about 10 ppm Cu plus other impurities. High purity ZnSe, containing small amounts or no oxygen compounds, was prepared by reaction of H2Se with zinc vapors at 600° to 800°C in an atmosphere of palladium diffused H2.7 The ZnSe thus produced was usually copper free and contained only 1 ppm by weight of magnesium as determined by emission spectrographic analysis. G.E.&apos;s electronic grade ZnS, which had about 10 ppm metallic impurities, was used without further treatment. ZnS-ZnSe charges were prepared by mixing the two compounds together, then sintering 24 hr at 1100°C in an H2S ambient. The gases, HBr and HC1, were commercial grade, of 99.9 pct purity, while the I2 was 99.999 pct pure. The single crystal seeds with (111) faces for growth were mechanically held in place by sealing the outer quartz tube to the growth tube. After the charge was introduced, the system was outgassed at l0-5 torr while heated to 500°C. The desired quantities of transport reagents were then sealed off in the system, which had been cooled to 25°C. The growth tubes were inserted into a furnace with the desired temperature and thermal gradient. The system was allowed to cool for 1 to 12 hr from growth temperatures of about 850" to 25°C. The tubes remained stationary during crystal growth. HCl CHEMICAL TRANSPORT GROWTH Preliminary runs with HC1 had a temperature gradient of 100° to 200°C and no seed or heat sink. Only small crystals were obtained in these experiments as

Jan 1, 1970

By F. P. Bullen

Empirical relationships between fracture stress, orientation angle, and diameter of crystal have been determined at 77°K. Orientation ranges of markedly different behavior were found—a law of constant normal stress&apos; of value a (diameter)-1/2 for the fracture of ductile crystals, and a condition of shear stress (or strain) for more brittle crystals. The observations are not consistent with current theories. An interpretation is advanced which is also applicable to observations on the effect of prestrain at room temperature on the subsequent fracture stress at 77°K and to the effect of cyclic stressing on the cleavage strength.&apos;&apos; The law of constunt normal stress&apos; and the brittle ductile transition are also explained. The interpretation is more consistent with the initiation of cracks by intersecting dislocations than with theories based on stress -concentration by dislocation arrays. ZINC single crystals are particularly suited to the study of cleavage because fracture occurs on the basal plane over a wide range of crystal orientations. Analysis of the conditions of stress and strain at fracture in crystals of different orientations should indicate which parameters control the cleavage process. Unfortunately, controversy has arisen over the correct empirical relationship between tensile fracture stress and orientation. Schmid&apos;s observations1,2 favored a &apos;law of constant normal stress&apos;, as observed in other materials.2 For zinc, however, the observed values are far below the theoretical strength and cannot represent the true limit of cohesion between neighboring atomic planes. Hence, the interpretation of such a &apos;law&apos; is not straightforward. Deruyttere and Greenough3,4 found a complex variation between tensile fracture stress and orientation; this variation did not agree with a &apos;law of constant normal stress&apos;. Two theories have been advanced to account for their observations: a) the propagation of cracks from low-angle boundaries,5 and b) the release of energy from piled-up dislocations during crack-propagation.4 The present work resolves the apparent discrepancy between the observations and shows that neither of the above theories are applicable to the tensile fracture of zinc single crystals. A phenomenological explanation, along the lines suggested by Gilman,&apos; is advanced and successfully applied to previously unexplained effects. EXPERIMENTAL DETAILS &apos;Crown Special&apos; redistilled zinc was used, except for one comparison series op tests using &apos;Tadanac&apos; electrolytic zinc. Crystals of 1 mm diam, subsequently called &apos;1 mm crystals&apos;, were grown from the melt in vacuo in precision-bore Pyrex tubes internally coated with graphite. Several specimens 1 in. long were cut from each crystal and chemically polished. Jigs were used to minimize handling strains, and crystals were mounted in the Polanyi machine the day prior to testing to allow recovery from any such strains. One-mm crystals were chemically polished for long periods to obtain 0.1 mm (approx) crystals. One-mm crystals were cemented into miniature gimbals by &apos;Araldite&apos; casting resin. The Appendix gives the reasons for using gimbals and the results obtained by other methods. More complete details of all techniques are given elsewhere.7 The symbols and terminology used are as follows: X = orientation angle (angle between tensile axis and line of greatest slope in the basal plane). T = tensile stress (on true cross-section) S,N = shear and normal stress (components of T with respect to the basal plane) ? = shear strain D = crystal diameter. The subscript &apos;f&apos; will be used to denote values at fracture. PART I-ANNEALED CRYSTALS EXPERIMENTAL OBSERVATIONS One-mm crystals were used to establish the variation of fracture stress at 77°K with orientation at fracture (Xf), Fig. 1. For 18 deg = Xf = 55 deg, a &apos;law of constant normal stress&apos; was observed. For Xf > 55 deg, the fracture condition approximated to a constant shear stress. At Xf< 18 deg, twinning occurred before fracture so that the results were not typical of homogeneous single crystals,4,8— such specimens will not be considered herein. The dependences of fracture stress upon Xf were of similar type for 6 mm,* 1 mm, and 0.1 mm crystals,

Jan 1, 1963

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8

Jan 1, 1923

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys&apos; enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.&apos; crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By Paul M. Tyler

MINOR industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz (Iceland spar, tourmaline, fluorite, selenite, mica), and nonfuel gases (air, helium, carbon dioxide). ALUM MINERALS The alums comprise a series of double sulphates (or selenates) isomorphous with potash alum, which, according to a ruling of the Pennsylvania courts, is the only product commercially described simply as "alum." Common alum occurs in nature as kalinite (K2SO4- A12 (SO4) 324H2O). The mineral mendozite (Na2S04) 3.A12 (SO4)3- 24H2O) is soda alum; tschennigite (NH4)2SO4.Al2 (SO4)3.24H2O) is ammonium alum; and there are about a dozen other native alums and related double sulphates. Alunite (alumstone or alum rock) has the formula Al2(SO4) 3.K2S04.4A1 (OH)3 and alunogen, Al2(So4) 3.18H20. Saline residues, found wherever natural water is evaporated, may contain sulphate of alumina, which for most uses is the essential ingredient of alum. Mineral wells and springs that emerge from beds of pyritiferous shale are typically astringent and at times form local deposits of alum, generally as incrustations. Acid waters acting upon aluminous rocks may form sulphates of alumina. The alums of commerce, as well as aluminum sulphate (concentrated alum), are produced principally by treating bauxite with acid, but they have been made also on a substantial scale from clay, cryolite, pyritic slates, schists, lignites, alunite, and leucite. Alum shale-chiefly clay, pyrite, and (usually) carbonaceous matter-was extensively used in England as a source of alum for more than two centuries. In France, pyritic lignites mixed with sand and clay were burned in heaps to red ash, the leach Liquors from which, after treatment with ammonia, yielded alum and copperas. Processes have been developed for making alum or aluminum sulphate from such diverse materials as feldspar, aluminous phosphate minerals, greensand, and mixtures of mica and

Jan 1, 1949

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By J. L. Giove, J. M. Hodge, R. G. Storm

The hardenability effect of molybdenum has been evaluated by a number of investigators, including one of the present authors.1,2,3,4,6 Considerable discreMncy exists, however, among the results of these various investigators, and two of them, Brophy3 and Kramer,4 have indicated that the apparent hardenability effect of molybdenun would vary, depending upon the other alloying elements in the steels being considered. The results of previous, unpublished work conducted at the Duquesne Works Laboratory of the Carnegie-Illinois Steel Corporation also have indicated significant differences in the hardenability effect of molybdenu~n in nickel and in chromium steels. The present investigation was undertaken in an effort to establish the mechanism governing this difference in the hardenability effect of molybdenum. This work involved both end-quench hardenability and isothermal transformation tests on two series of steels of varying molybdenum content. One steel contained 3 pct nickel and the other 1 pct chromium. It was hoped that such studies would shed further light on the mechanism of this behavior. Materials and Experimental Work MATERIALS The chemical compositions of the steels used in this investigation arc shown in Table 1. These steels were furnished by Battelle Memorial Institutc in the form of 100-lb induction furnace ingots. The top half of each ingot was forged to 1 3/8-in. square billets and then rolled to I-in. round bar stock for isothermal transforma- tion studies. The bottom half of each ingot was forged into approximately 1 1/4-in. rounds for end quench tests. All of the steels were normalized from 1650°F and tempered at 1100°F before nlachming to end quench or isothermal samples. END-QUENCH TESTS standard l-in. diam end-quench tests were made on each of the steels. The test bars were austenitized at 1600°F for 30 min,, quenched in a standard Jominy jig, and hardness surveys were made in all tests. The 95 pct martensite point was deterInined from hardness values5 and cheeked by metallographic examination. The jominy distance values for 95 pct martensite were converted to hardellability values in terms of ideal diameter (Dl), using a revised carve for the relationship between Jominy distance and ideal diameter. This curve was based on the cooling time from the A1 to the bainite nose temperatures rather than on the usual criterion of half-temperature time. The cooling rates as determined by Russell and Williamson9 were used as a basis for this relationship. The derivation of this curve is described in detail in the appendix. ISOTHERMAL TRANSFORMATION STUDIES Samples for the isothermal transformation studies were quarter sectors of 1/16.is-in. thick slices from the 1-in. round bars. All samples were austenitized for a total the of 15 min., transferred rapidly to a lead bath for isothermal transformation, and brine quenched from the lead bath. A time of 3 see was allowed for the sample to come to the temperature of the lead bath, and this time was not included in the isothermal transformation times. Each sample was examined metallo-graphically at a magnification of 100 diam. The per cent transformation was estimated by comparison with standard micrographs, and the values were plotted against the on log/log coordinate paper. At least 4 and as Inany as 10. points were plotted for each steel. A line was drawn through the points for each steel, and the times for 5 pct transformation were obtained from the plot for each steel. Isothermal transformation diagrams in terms of 5 pet total transformation, covering the temperature range of 800 to 1200°F, were determined in this manner for an austenitizing temperature of 1600°F. The times for 5 pct transformation at the bainite nose for austenitizing temperatures of 1800 and 2000°F were also determined in the same manner. These times for 5 pct total transfor-

Jan 1, 1950

By Alfred Siegel

Mineral pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, but rather such compounds as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-limonite (2Fe2O3.H2O to Fe2O3.4H20), hematite (Fe2O3), or magnetite (Fe2O3.FeO). Man&apos;s first permanent coloring materials were earth pigments-the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands forth with $16,000,000 per year; it is surpassed by titanium, lead and zinc pigments. Of this sum,21 natural pigments supplied 31 pct of the tonnage and 16 pct of the value of the total finished pigment in 1957, the remainder representing the tonnage and value of sales of the synthetic iron oxide colors. The average value of finished natural pigments in 1958 was $80.62 per ton. The average value of manufactured pigments in the same year was $202 per ton. Of the 60,000 tons of manufactured colored pigments sold in 1958, the reds comprised 76 pct of the market and the yellows 20 pct. The reds furnished 68 pct of the value and the yellows 24 pct. Of the finished iron oxide pigments (natural and manufactured) sold in 1958, the reds dominated the market with 66 pct of the quantity and 63 pct of the value; yellows supplied 17 pct of the quantity and 20 pct of the value, and browns furnished 11 pct of the quantity and 10 pct of the value. The average value of the reds was approximately $152, and the average value of the yellows $190 per ton. The highest valued pigment in 1958, with almost 12 pct of the total tonnage and 21 pct of the value of the iron oxide pigment market, was manufactured red from calcined copperas valued at $286 per ton.

Jan 1, 1960

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.&apos; The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By C. W. Sherman, J. Chipman, H. I. Elvander

J. F. Elliott—This is an excellent piece of work and makes a chemical metallurgist more enthusiastic than ever about what can be done with multicomponent systems, if we have satisfactory data. I have a remark to make on the interpretation of fig. 5. First, I will comment on the problem of activities in solutions. The iron-sulphur system has in its phase diagram an intermediate solid phase FeS. The occurrence of an intermediate phase is normally associated with negative departures from Raoult&apos;s law over a portion of the activity curves in the liquid. (Perhaps it would be better to reserve the phrase "departure from ideality" to departures from Raoult&apos;s law line rather than to departures from Henry&apos;s law line). Fig. 5 indicates that the deviation of the sulphur activity curve from the Henry&apos;s law line is negative;

Jan 1, 1951

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8

Jan 1, 1923

Who&apos;s Who in Mineral Engineering 1977 - SME Membership Directory of the Society of Mining Engineers of AIME

Jan 7, 1977