Search Documents

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

Jan 8, 1950

By C. M. Schwartz, J. R. Bridge, D. A. Vaughan

THERMAL expansion coefficients of a uranium were originally reported' on the basis of X-ray diffraction measurement of lattice constants at 25°, 300°, and 650°C. These data have been reproduced by Katz and Rabinowitch.' CuK radiation had been used in this work, with consequent crowding of the patterns. Considerable overlap of the back-reflection lines was observed as the temperature was raised. Subsequent reexamination of the data led to the conclusion that errors had resulted from failure to obtain unequivocal indexing of the high angle reflections at elevated temperatures. The measurements have been repeated, using FeK radiation, which provided sufficient dispersion to assure proper indexing of the reflections, at each temperature level. The unit cell dimensions were re-determined at ten temperatures, from 25" to 650°C. Schuch and Laquer easured the macroscopic contraction from room temperature down to —253°C, and reported a negative value from —210" to —253°C; they suggested the possibility of the occurrence of a phase change. In the present work, the lattice constants of uranium have been measured down to —253°C, to test this hypothesis. Filings were prepared from a single piece of pure uranium bar stock. They were carefully cleaned with a magnet and pickled in nitric acid to remove traces of iron from the file. They were then annealed at 600°C in a sealed evacuated silica tube. The annealed filings were pickled in strong nitric acid to remove any oxide layer, washed in water and alcohol, quickly dried, and sealed in evacuated thin-walled silica capillary tubes. If properly sealed, the sample could be heated to the a-ß transforination temperature without significant buildup of the diffraction pattern of oxide. The high temperature X-ray diffraction camera was modified from the design of Hume-Rothery and Reynolds.' The thermocouple used to record the specimen temperature was calibrated from lattice-constant measurements of a standard silver specimen, using the Hume-Rothery and Reynolds values for silver over the temperature range from 25" to 700°C. Temperatures were reproducible to 210°C. Temperatures to —210°C were attained by passing precooled gas over the sample. The gas from the cooling train was directed over the sample capillary tube and thermocouple by means of a chimney of 1-mil polystyrene. The 36-gage Cu-constantan thermocouple had been calibrated by

Jan 1, 1957

ON July 2 the Krupp plant in Essen was occupied by the French. The City of Frankfurt, on the edge of the Mayence Bridgehead was surrounded by the French. French infantry and cavalry occupied some more towns in the Ruhr. These moves were apparently in the way of reprisals. The Bank of England on July 5 raised its discount rate from three per cent. to four, per, cent., the lower rate having previously prevailed for almost exactly a year.. The advance appears to have been inspired by the reserve ratio, but especially owing to the fact that the low rate in the London market had led to the out-flow of funds from there to other markets. Philip Snowden brought up again in the British .Parliament his motion in favor of the condemnation of the capitalistic system and the substitution of socialism. The motion was put to vote and was defeated by large majority, only the members of the Labor party voting for it. The Allies and the Turks finally came to an agree-ment at Lausanne, the Turks getting about all for which they asked. It would be tiresome to record the details. The main fact is that the Turks, after having been ejected from Europe in 1918, are now going to return. Russia agreed to the settlement respecting the Straits. The Soviet Government of Russia formulated and adopted, subject to ratification, a constitution for the United States of Russia, which appears to be patterned after the constitution of the United States of America and the unwritten constitution of Great Britain. The important thing about this seems to be that it definitely reunites the constituent parts of the old Empire, the semi-independence of the Ukraine being surrendered.

Jan 7, 1923

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By C. R. Hayward, H. O. Hofman

The aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation. The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment, that the present paper deals. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization; by casting a thermal balance to find the distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a summary of several tests will give the best method of operating. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jan 1, 1910

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By Maurice B. Dusseault, Edo Nyland

Numerous consistent seismic signals are being generated in a pilot fireflood in a 750 m deep high permeability unconsolidated channel sand in Eastern Alberta. The pilot has a central air injection well, eight production wells on artificial lift, and two internally placed observation wells. Surface seismometers and a 12-hydrophone downhole string were deployed to detect seismics signals. Date were collected for 22 hours employing signal-triggered event detectors recording on cassette tapes. Monitoring during twelve hours of steady air injection at 625m3/s yielded a clear event frequency of about 50 events/h. The events were mostly clear compressional wave arrivals originating in the vicinity of the firefront. Stopping air injection caused a gradual drop in event frequency, and the rate was reestablished when air injection was reinitiated. Spectral frequency analysis and knowledge of material properties indicate that the events are shears of a stick-slip nature associated with the strain-weakening behavior of the over-compacted reservoir sands. The event amplitude indicates small-scale shearing, and different amplitudes suggest that planes re-shear with lower energy release levels. The triggering mechanism for shear rupture is high shear stress created by thermal expansion in the area of highest ther- mal gradient. Other enhanced recovery techniques may also produce useful signals for process control. In particular, steam flooding, hydraulic fracturing, and high-pressure injection operations likely generate mappable microseismic events which can be applied directly to production/ injection strategy.

Jan 1, 1982

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.&apos;s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,&apos; the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.&apos; Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

By Luis N. Henriquez

One form of encouragement for the small copper mining sector in Chile has been the construction and management of custom mill facilities to process the ore. The paper describes an economic analysis framework for the evaluation of government custom milling opportunities. Feasible mill locations and capacities within a region are selected and the infrastructure and milling costs associated with each combination of location and capacity are assessed. For each combination, the economics of developing and operating known copper deposits in the region is evaluated, and an optimum cut-off grade and mine capacity is selected for the deposits which justify development. Since the total ore supply from mines in the region may exceed a particular custom mill capacity, mine development is scheduled to optimize the economics of the mill facility. Finally, the best custom mill location and capacity is selected on the basis of overall costs and benefits. A copper mining region in northern Chile is used to illustrate the application of the model. A mobile mill approach is examined and compared with the fixed location mill alternatives. Results are analyzed as a function of copper price.

Jan 1, 1977

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L&apos;slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4&apos;6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6&apos;7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L&apos;slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4&apos;6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6&apos;7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose.

Jan 1, 1929

By H. T. Matson

IN the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals.. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. Those interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.1

Jan 1, 1930