Search Documents

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958

By Sultan Amerie

PERSIA looms up more prominently each year as one of the richest oilfields in the world. The actual production in the south and the possibilities in both the north and the south are very great. The output in the south, where the Anglo-Persian Oil Co. operates a wide concession, is steadily increasing, the returns for the fiscal year 1922-23 being 2,957,028 tons. The estimated production for. 1923-24 is 3,775,000 tons. The figures for the past few years have been as follows: 1918-19 1,106,415 tons 1920-21 1,743,557 tons 1919-20 1,385,301 tons 1921-22 2,327,221 tons According to the company's last annual report, the production from the -Persian fields operated by its subsidiaries has been well maintained and is now being increased to deal with the expanding off-take of the company's refineries at Abadan, Persia, and Dandarcy, Wales. Test drilling in an entirely different area in Persia indicates the existence of a new oilfield, which it is intended for the time being to hold as a reserve.

Jan 3, 1924

By E. T. Dumble

The history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of them. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid down over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arltansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southcrn extension of the interior continental seas, in connection with the sedimcnts and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found. East of the anticlinal the oldest beds which appear in contact with the Bend are the Trinity Sands of the Lower Cretaceous. No evidence has

Jan 1, 1916

By G. P. Connell, R. E. Gilmore, J. H. H. Nicolls

The purpose of this paper is to suggest a procedure for indicating the dividing line between noncaking coals and those that have weakly caking properties. A laboratory agglomerating test as an aid in classifying weakly caking coals is outlined and its merits in comparison with the standard agglutinating method advanced by the U. S. Bureau of Mines are discussed. No attempt, however, is made to discuss in detail either the different methods for determining "caking" and "agglutinating" indices or the various systems of classification. Two methods, differing somewhat in procedure, have been employed and recognized as suitable for determining the caking or agglutinating values of coals; namely, those in which an inert material such as sand, electrode carbon, etc., has been mixed with the coal before being heated, and those in which the coal is carbonized alone. In all such methods, the coal with or without the inert material is in the finely divided state and the index or value sought is derived from the examination of the residue after heating in a closed crucible or other container. The procedure outlined by Selvig, Beattie and Clellandl is the most recent representative of the method using sand as inert material, while the agglomerating test described below is representative of the method in which the coal is carbonized alone. The standard volatile-matter determination affords a means for observing the coking properties of a coal, and this has been described by Rose2 as the simplest of all coking tests. According to him, "the resulting coke button will indicate whether the coal is noncoking, feebly coking or strongly coking," despite the fact that "almost every condition in this test is at variance with large-scale carbonizing practice." Lessing,3 the

Jan 1, 1934

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. P. King

The two-phase distributed-parameter kinetic model for flotation has been wed as the basis for a digital simulation of flotation plants of arbitrary configuration. Ores that contain any number of minerals can be handled. The effects of incomplete liberation and particle-size distribution are specifically allowed for. The simulator allows the investigation of variations in throughput and in the slurry density of the feed, and of variations in stage volumes and aeration rates. It can handle cell behavior even under conditions of hindered flotation. The requirements for data preparation are completely documented so that the computer program is suitable for general-purpose use. The program is written in Fortran. The output from the simulator consists of the complete material flows in the plant, as well as the grade, recovery, and particle-size distribution in each stream.

Jan 1, 1976

By S. G. Malghan

Steel consumption forms a significant part of the operating cost of a minerals processing plant. An estimated 250 kt (276, 000 tons) of steel in the US and over 500 kt (551, 000 tons) worldwide are consumed each year in wet grinding alone. The depletion of ore grades and the need for finer grinding of abrasive ores are expected to increase steel consumption even more. Through continued research and development by the mining industry and the suppliers of steel products, several methods to reduce steel consumption have evolved. This paper critically reviews the mechanisms involved in steel wear and the currently available methods, materials. and operating conditions for reducing steel consumption. Particular attention is given to liner design modifications and substitution of rubber liners for steel liners.

Jan 1, 1983

By O. K. Riegger, L. H. Van Vlack

The median angle of relatively few two-dimensional observations provides a satisfactory value for dihedral angle determinations. Those data that contain bimodal or non-equilibriated dihedral angle distributions are readily detected. THIS paper is concerned with a statistical simplification for determining dihedral angles in solids. Microstructures are partially controlled by relative energies of interphase boundaries and grain boundaries. smith1 has shown rather conclusively that such boundaries may be equilibrated to give a vectorial balance at grain and phase edges. Thus if an accurate measurement is made of the dihedral angle associated with grain and phase edges, an accurate calculation of the relative energies may also be made. The accurate measurement is difficult because the dihedral angle involves two planes in three dimensions, and only a two-dimensional cut through the dihedral angle is usually observed. Such a two-dimensional cut is statistically random provided there is no preselection or orientation. Harker and parker2 have shown that the mode of the frequency distribution of observed angles is within 5 deg of the true angle if the true dihedral angle is 120 deg. smith1 had calculations made to show that the same generalization could apply to dihedral angles of 30, 60, 90, and 150 deg. This procedure of requiring the determination of the statistical mode is time consuming because experience has shown that more than 200 angle observations are necessary before the mode is clearly indicated. It is possible to determine the dihedral angle with equal accuracy with only 25 angle observations if the median angle is used in place of the mode angle. Use is made of Harker and parker's2 basic equation tan =2 sin x cos

Jan 1, 1961

COUNCIL OF SECTION DELEGATES Nicholas A D'Arcy, Jr, Chairman (Southern California Section) Charles Chapman, Vice-Chairman (Florida Section) Ben H Parker, Secretary (Colorado Section) Frontier Refining Co Boston Bldg Denver 2, Colorado

Jan 1, 1956

By S. L. Tainter

This paper describes the nature of engineering and geologic services for the production stage and a review of pit design factors peculiar to the development period. The Mission pit has passed into the mining phase where development is of secondary importance; however: until the pit reaches its final size, development will be a continuing function occurring simultaneously with mining operations. The deposit occurs in an extensive zone of altered sedimentary rocks which have been fractured by three fault systems, flexed or folded, and intruded by monzonite porphyry. The deposit is a low-grade copper sulfide "porphyry" type orebody within a broad zone of pervasive hydrothermal alteration in sedimentary rocks.

Jan 12, 1965

By William J. Douglas, Jack T. Urie, Randall D. Metz

Production and financial planning for a new underground mine requires the coordination of equipment and coal reserves in a manner which assures that resources are utilized efficiently in achieving the target mine production. It is necessary to establish the productions which are attainable at the section level during different mining operations (advance, retreat, development) and under different mining conditions (roof, seam height, resource quality). It is also necessary to identify the interactions between production plans and ventilation equipment So that operations can be carried out without disruptions caused by inadequate ventilation. A set of computer models has been applied in planning a number of new coal, oil shale, and phosphate mines. A critical path production model, CPMINE, was used to determine face production levels for different cut sequences and seam heights, taking into account machine performance characteristics and operational availabilities under these varying conditions. The results formed a production data base for use in the mine sequencing model, MPLAN. This model processes each of the segments of a user-defined mine sequence network (strategy tree) taking into account the equipment available for mining operations and the previously determined production scheme devised by the mining engineer. Mine ventilation was analyzed with an expanded version of the Penn State MVS Ventilation model to determine fan and ventilation shaft requirements for supporting alternative production strategies. The MCOM mine cost analysis model has been applied to evaluate the economic performance of mining alternatives. The results of these studies were used to make decisions relating to equipment selection and acquisition schedules for both room-and-pillar and longwall mining systems. The approach and procedures which were used during these studies are described.

Jan 1, 1983

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Geologist. Age, 34; wide experience in all Lake Superior iron-ore districts and Arkansas bauxite district. Examinations, tonnage estimates, reports, direction of prospecting, geologic mapping, churn and diamond drilling. Excellent references. A-2681. Mine Superintendent or Manager. Graduate mining engineer, age 31, married, 10 years' experience, now in government employ as metal-lurgist, desires employment with reputable mining company. New York interview if desired. A-4219. Research Engineer, now in Chile on erection of 50-ton mill with modern machinery for treatment of Chilean nitrate, desires connection, from the first of next year, with firm operating in South or Central America. A-4915. Mining Engineer. Young graduate of Michigan College of Mines; capable of handling men, conscientious worker; desires a position that will lead to assistant superintendency. Any place in the United States. Initial salary relatively unimportant. A-5195. Metallurgist, married, age 25; technical graduate; 3 years' experience in blast and open-hearth furnaces, blooming mills, metallographic, and heat treatment work; desires position as sales engineer in the Pittsburgh district. A-5196.

Jan 12, 1919

By Eugene P. Pfleider

Research indicates that the cube diamond is a superior stone for drill bits. It can be oriented to combine a long cutting edge with structural strength and high resistance to wear. Test bits set with preferred orientation give double the bit life at astoundingly low diamond loss in comparison to oriented octahedral diamonds. A PROGRAM of research on the orientation of diamonds in drill bits has been under way for several years at both the United States Bureau of Mines Experimental Mine at Mount Weather, Va., and the School of Mines and Metallurgy of the University of Minnesota. Reports on past work done both in the laboratory and the field are available in the technical press.1,3,4 The results of such drilling, done under comparable conditions, show that bits having diamonds oriented in a direction that combines structural strength and greatest hardness not only can advance somewhat faster than random set bits but can do this with a unit diamond loss of 50 pct or less. Several bit manufacturers have initiated the training of diamond setters in the principles of orientation on the basis of the above-mentioned research results. The basic information on the crystallography and hardness variation of the diamond was presented in an earlier paper,' which pointed out that the diamond is several hundred times harder along certain directions and certain faces than on others. The same article discussed the drilling results obtained with a group of nine bits having octahedron diamonds set with on-point, positive (gouge) rake, and negative (drag) rake orientations. The testing of oriented cube diamonds is an extension of this research program, employing the same procedures and equipment (Hy Mac hydraulic drill unit, EXT diamond core bits, St. Cloud Pink granite) as previously described. This current work covers the test experience of seven bits set with cube diamonds running approximately 10 stones per carat. The individual stones were near perfect cubic form; hence it was simple to orient them in any desired direction. The cube is a comparatively rare crystal form of the diamond, although considerable numbers are produced from the Congo. It is understood that most of the cube diamonds are retained in Africa, where they are either used locally for diamond bit manufacture or ground up to make powder. They have been considered to be an inferior stone for drilling purposes.

Jan 1, 1954

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

Jan 1, 1959

By Noel Stearn

OF THE many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. , In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself.

Jan 1, 1928