Search Documents

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

[ ]

Jan 1, 1938

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931

By C Gunther

Mining examinations are of several kinds and the scope of the investigation depends in each case upon the purpose for which the examination is made. A formal examination of a developed mine is an expensive undertaking; from one to several months are allowed for the work according to the size of the property; many samples are taken; investigation is made of the geological features, including, perhaps, a topographical and geological survey of the surface; the metallurgical treatment of the ore is studied; finally, a determination of costs is demanded. Formal examinations are made for prospective purchasers or as a basis for the consolidation of several properties, and occasionally, in the owner's behalf, to verify the work of resident engineers, or to determine the readiness of a mine for equipment and the kind and capacity of equipment it shall receive. A formal examination of a mine should not be undertaken until a preliminary examination has shown that it is justified. It is regrettable that some engineers are in the habit of prosecuting long and exhaustive examinations of properties whose lack of merit should be, and perhaps is, apparent from the start, or of continuing their investigation long after an unfavorable result is seen to be inevitable. This wasting of a client's money is a species of trickery difficult to prove, and therefore the more contemptible. Preliminary examinations are precisely what the term implies, and are undertaken to determine the advisability of making

Jan 1, 1932

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

By Theodor Zuschlag

Electrical prospecting is the art of exploring the structure of the subsoil in regard to conductivity variations and interpreting the results of such exploration as to their geological meaning. Electrical prospecting has been applied during the last few years with outstanding success, not only to prospecting1 for ore but also to structural studies.2 Both applications have proved helpful to the geologist, and the latter application especially promises to become of still greater importance in the future. The mapping of structures is the most important function of the oil geologist. Oil is lighter than water, therefore in water-bearing beds it will migrate upward until the migration is stopped by a bed impermeable to the oil. Geologic structures such as domes, anticlines, faults and terraces, offer good prospects in the search for oil accumulations and can be traced easily by electrical prospecting, provided they are composed of a series of sedimentary layers of which at least one possesses fair electrical conductivity and follows the general trend of the structure. Conditions for Successful Mapping The first condition, fair electrical conductivity, is met in almost any oil-bearing series, because generally the electrical resistance of a sedimentary bed is identical with the resistance of the more or less saline waters, filling partly or entirely the pores of the rocks.3 Briefly, the electrical resistivity of a bed can be expressed for all practical purposes by the product R X P, where R is the specific resistance of the waters in the rock pores and P a factor depending upon the percentage of water by volume in the rock. The specific resistance of any solution can be computed from the chemical analysis, being primarily a function of the

Jan 1, 1932

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Frank Tolonen

IRON-ORE beneficiation is becoming of vital importance to the Lake Superior region, since only a few decades will be needed to exhaust the direct shipping ores even if generous allowances are made for discoveries of new orebodies. If the region is to continue as the chief source of ore to the steel industry of the United States, it must concentrate or otherwise beneficiate the enormous tonnages of available iron formations. A beginning along this line has already been made. About one-fifth of the total shipment, even now, is the product of some sort of concentrating process, while another fifth is improved in physical structure by crushing, screening, drying, sintering, or some other similar method. The amount of material amenable to these processes is limited, however; and, in order to be able to utilize the billions of tons of iron formations that cannot be so beneficiated, an intensive study of their nature and concentration possi-bilities is necessary. As long as high-grade ores are available in ample quantities, ore dressing is economically impossible, but as soon as the supply nears exhaustion it becomes necessary. At first the products of ore dressing must meet as nearly as possible the same specifications as the rich ores in order to be adapted to the reduction processes already established. The future requirements as to quality will depend on the one hand upon the ability of the ore dresser to eliminate undesired constituents and charac-teristics in the material, and on the other upon the adaptation of the reduction processes to the product that can be economically supplied. A better understanding of the blast furnace and other reduction reactions, and improvements in the preparation of raw materials, should enable the Michigan districts to continue to supply ore for a long time to come. The study and testing of the iron formations necessary to bring a utilization of the low-grade ores, though requiring time and effort on the part of all concerned, should not be postponed, especially since the economic situation forces the use of the highest grade ore in preference to the leaner material.

Jan 1, 1933

By Richard J. Gonzalez

The petroleum industry includes varied and extensive operations required to supply increasing quantities of refined petroleum products and natural gas that are essential for the economic progress of an expanding population Petroleum has provided the power for the transformation from the "horse and buggy days" to the age of jets and space exploration, and for the remarkable improvement in productivity per worker in agriculture and manufacturing. Without increasing quantities of oil and gas, the world would face painful readjustments to more expensive forms of energy and lower standards of living Petroleum operations start with exploration, development, and production activities that supply the basic crude oil and natural gas Pipelines, ships, barges, and trucks first transport the raw materials to processing centers and then move the finished products to the ultimate consumers. Processing plants extract liquids from natural gas and refineries convert crude oil into a wide range of products These products include transportation fuels, feedstocks for conversion into numerous products (such as fabrics, rubber, and plastics), light fuels for heating, lubricants, and heavy residual materials (industrial fuel oil, asphalt, and coke) The final activity of wholesale distribution and retail marketing moves products into millions of homes, farms, industrial plants, and motor vehicles The use of coal exceeded that of oil and gas until 1946 in the United States and until 1968 in the rest of the world. However, oil and gas have proved to be such convenient and attractively priced fuels that they now supply three-fourths of the total commercial energy (including coal, hydroelectric, and nuclear power) used in North America and more than one-half in the rest of the world. LARGE SCALE OF OPERATIONS By the beginning of 1970, world crude oil production exceeded 43 million bbl daily, -equivalent to more than 2200 million tpy In addition, natural gas and the liquids recovered from processing natural gas supply about 40% as much energy as crude oil Production of oil and gas provide by far the highest value of all mining operations. In the United States, the value of oil and gas production in 1969 of $13 8 billion exceeded the $13 0 billion value for all other minerals The rate of expansion in use of petroleum has been extremely rapid since World War II World crude oil production doubled from 7,500,000 bbl daily in 1946 to more than 15,000,000 bbl daily by 1955 It doubled again to 30,000,000 by 1965, and will double again by 1975 The use of natural gas has increased greatly in the United States and also in Europe, as important discoveries in the Netherlands and the North Sea and technology for moving liquefied natural gas from Africa provided attractively priced supplies

Jan 1, 1976

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

Several of the current concepts of brittle fracture involve consideration of, the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack. It is but a small step to extend the theory to include flaws and defects of other sorts which, though they may be less tractable mathematically than cracks, may still function as stress risers in a real sense in real materials. Brace 2 proposed that the application of the Griffith theory to rock material could be tested in two ways: "(a) by finding the orientation of cracks from which macroscopic fractures have developed and (b) comparing failure strengths from tests at different conditions of loading." In 1963 the author and coworkers at the Bureau of Mines, Twin Cities Mining Research Center, working on a problem involving relationships between strength, sonic velocity, and microstructure "eveloped an experimental technique to examine several somewhat similar questions; namely. does the frequency of occurrence of actual or potential stress risers dictate the relative strength of the material as proposed by Weibull;4 can actual flaws or defects in the rock structure be identified and related to strength and perhaps other properties in accordance with Griffith's theory; and is the anisotropic strength and elastic behavior of certain rocks related to the preferred orientation of these actual or potential stress risers? The experimental approach developed to answer these questions appears equally applicable to the testing of Griffith's theory as proposed by Brace. Basically the approach consists of a series of point-load tensile tests followed by petrofabric examination of thin sections prepared from the specimens in order to identify and apply a quantitative measure to microstructural defects which may have contributed to the failure process. In the point-load test, tensile stresses are induced by a compressive load applied to the center of a disc-shaped specimen by means of two opposing hemispherical indentors. Failure generally occurs as a single fracture parallel to the axis of loading and bisecting the disc. Because of the geometrical symmetrical the induced tensile stresses are symmetrical about the loading axis

Jan 1, 1967

By Charles H. Fettke

The Bradford field of northwestern Pennsylvania and adjacent portions of New York state has attracted world-wide attention in recent years on account of the remarkable success that has been attained in the application of water-flooding as a means of increasing the extraction of oil from a pool that had almost reached the economic limit by ordinary production methods. It is one of the few large oil fields in which artificially conducted water drives have thus far proved successful, although many attempts have been made to apply them elsewhere. As detailed a knowledge as possible of the character of the producing sand in this field is therefore of considerable interest, not only from a scientific but also from a practical standpoint. Outside the Bradford field, such knowledge should aid operators in determining whether or not their sands are amenable to flooding. In the Bradford field itself flooding operations are not uniformly successful over the approximately 85,000 acres of productive area, due in many instances primarily to variations in sand conditions. A knowledge of just what these variations are would often be a great aid in overcoming the difficulties, or else would save considerable sums of money which might otherwise be wasted in experimenting in areas where the chances of success are very small. Realizing that more precise information in regard to the nature of the reservoir rock was essential to improvements in the methods of oil recovery, the Northwestern Pennsylvania Oil Producers Assn., by private subscription of its members, took a core of the Bradford sand from a well 1/2 mile west of Custer City, Pa., during the spring of 1925. The Forest Oil Co. also took a core of the same sand from a well about 8 miles east of Bradford at that time. The cores were submitted to the United States Geological Survey for study and A. F. Melcherl has published the results of porosity determinations on the Custer City core.

Jan 1, 1929

By Richard W. Smith

KYANITE, long known to occur in Georgia, did not excite commercial interest until about 1930. Investigations revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumula-tion from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not' more than a few feet. The larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersham County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habersham County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanite-mica schist belt in Habersham and Rabun counties will be discussed in this paper.

Jan 1, 1936

By F. W. Bradley

This chapter on the Alaska Juneau mill is intended to make clear that "choice of methods," or the selection of proper methods, is the first essential step in launching a new enterprise; and to illustrate that when entering into new country where local conditions and physical features are new or strange to an engineer, he should respect the practices already adopted and followed in meeting peculiar conditions in these new countries that may seem strange to a casual visitor. For example, Americans going into Malay Peninsula with their most up-to-date machinery for drilling placer prospect holes found their cost to total about $3 per foot; by adopting native methods, it was found the same work could be done for 50 cents per foot. Also, those not used to frozen road conditions in a country of arctic climate might scrape the snow off such a road and cause unending road troubles into the following spring and summer; while natives understanding local conditions would leave the snow on the road. So in the neighborhood of Juneau, Alaska, where successful gold-milling operations had been going on for

Jan 1, 1932

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

By Thomas J. O’Neil

During the past five years, the mining industry has been subjected to new operating constraints that are unprecedented in number, scope, and urgency. The industry must operate in a safer, cleaner manner, yet produce more without large price increases. Compliance with any new sweeping legislation is always difficult-and particularly so in today's adverse economic climate, which is being aggravated by the steady stream of environmental control and tax-reform programs. In effect, while government is unwittingly but surely undercutting the country's productive capabilities, it blames industry for the resulting failure to meet consumer demand. Any such real or alleged failure then brings heightened bitterness from Congress. During the recent energy shortage, for instance, threats of nationalization were ventilated in public along with proposals to abolish the mineral depletion allowance.

Jan 11, 1974

Electro-mechanical actuator, self-protected for mechanical and electrical overload, is developed by RACO. Tubular housing consists of squirrel cage motor with hollow rotor shaft and inner threads in the rotor. Features stroke distance of 2-72 in. and wide range of trust (20 lb-10 tons). (100) Agglomeration systems, offered by Ferro-Tech, incorporate pelletizing, briquetting and extrusion systems to agglomerate materials too fine to convey, load or feed to a process. Equipment includes disc and drum pelletizers, briquetter presses, compactors, extruders, pugmills and mixers, dryers, coolers, feeders and conveyors. (101)

Jan 9, 1973

Jan 1, 1879

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm's length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"' developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940