Search Documents

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By F. W. Luerssen, J. F. Elliott

F LUSHING the early slag from a stationary open Fhearth having a high percentage of hot metal in its charge is necessary in order to remove silica from the system. The flush slag is strongly oxidizing and is somewhat acidic. It has, however, considerable capacity to extract phosphorus from the bath and it also removes considerable manganese. It seems probable that factors which control the distribution of phosphorus and manganese between slag and metal in the refining period also should be dominant in the flush and postflush periods. Several studies, as summarized elsewhere,1,2 support the viewpoint that conditions closely approaching equilibrium for these elements are rather readily established during the refining period. Over the years these studies have repeatedly demonstrated that 1—high slag v01ume, 2—low bath and slag temperature, 3—basic slag, and 4—strongly oxidizing slag favor rapid elimination of phosphorus from the bath to the slag. They also show that the following conditions favor retention of manganese in the bath: 1—low slag volume, 2—high bath and slag temperature, 3— basic slag, and 4—minimum oxidizing power of slag. When it is considered that the flush slag often carries as high as 75 pct of the manganese charged and only 25 to 60 pct of the phosphorus charged, it is evident that in removing silica much manganese is sacrificed but phosphorus removal is far from conplete. Because of overriding circumstances, this is accepted in most operations and actually it is considered to be inevitable. This may account for the fact that little attention has been paid to conditions affecting the elimination of phosphorus and manganese in the flush slag. A recent study of the behavior of various charge oxides has developed considerable information on the flush and postflush periods. Because the data are felt to be of general interest, they have been brought together and Presented in this paper. The object is to show the various factors in the flush and postflush periods which influence elimination of phosphorus and manganese. Physical Conditions During and After Flushing Physical conditions existing during the flush vary from plant to plant, from shop to shop, from furnace to furnace, and even from heat to heat. They are strongly influenced by the physical and chemical character of the charge oxide which is ordinarily necessary to provide sufficient oxidizing power early in the heat. Invariably the period is characterized by a vigorous reaction between the principal re-actants: the hot metal being added and the charge oxide. During the flush, it is probable that the slag acts to some extent as an oxidizer; but, because of the critical influence of the behavior of the charge oxid'e on flushing action, it seems apparent that the oxide itself is the dominant oxidizer. Fig. 1 shows the course of two heats which were selected as being typical of the group studied. Heat A was charged with 55 pet hot metal, based on the total metallics charged, and heat B had 57 pct hot metal. As indicated in Table I and Fig. 1, the melt-down slag, which is not usually voluminous and which is principally FeO, expands greatly in volume and will show rather high levels of SiO2, MnO, and P2O5 very soon after the beginning of the hot metal addition. Simultaneously, large volumes of CO are liberated which cause violent mixing of slag and metal. It is of interest to note that the time required to bring carbon down to a low level is very much longer than that required for the removal of silicon, manganese, or phosphorus. At the end of flush, carbon in the bath is still approximately 2 pct. When strongly reducing hot metal is brought into contact with strongly oxidizing conditions within the furnace! it is probable that the rate of mass transfer to the slag (and atmosphere) of silicon, manganese, phosphorus, and carbon initially depends principally on the rates at which the two participating phases are brought into contact That is, it depends on the nature of the various reactions. Later in the flush period, when the scrap is virtually all dissolved and the action of the bath has settled down to a steady and somewhat gentle boil, it is likely that other factors, such as the transfer of oxygen across the slag-metal interface, become dominant. The temperature of the slag-metal system is far from uniform. Heat is being driven by the flame down through the slag. Bubbling and surging of the metal also frequently brings portions of the bath in contact with the flame. At areas of contact between the ore and liquid metal, or slag and liquid metal, the oxidizing reactions generate much heat. On the other hand, scrap is being melted which tends to absorb large quantities of heat. Because the liquid bath is high in carbon, the steel scrap is brought into solution rapidly. This can proceed at a rather low temperature; and until much of the scrap has been taken into solution, the bath temperature would not be expected to increase appreciably. Consideration of these factors leads to the conclusion that during the flush period the slag should be rather hot and the bath relatively cold. Both observation and temperature measurements bear this out. Experimental Data The extended program of charge oxide evaluation permitted study of the widely varying conditions existing during the flushing period. Slag and metal analyses and bath temperatures reported herein (Tables I and 11) were obtained toward the latter portion of the work. Four different types of charge oxide, sinter, two types of hydraulic cement-bonded soft ores, and a pyrobonded agglomerate were used in the study. Although the heats reported were from only one 205 ton furnace, they show variations in flush slag analyses all the way from 25 pct FeO, which is typical with the use of a hard natural charge ore, to 45 pct FeO which resulted when a very poorly agglomerated fine ore was used. The physical behavior of the flushes showed a correspondingly wide variation from well controlled reactions to violent surges following periods of inac-

Jan 1, 1956

By R. Schuhmann

Jan 1, 1965

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By Y. Nakada, E. J. Fasiska, A. S. Keh, L. Zwell

DURING an investigation of solid-solution hardening of nickel by carbon,' we found that there were no reliable data on the dilating effect of dissolved carbon on the unit cell of nickel. Bernier2 reported an increase in lattice parameter of nickel (3.523A) when an unknown amount of carbon was introduced into solid solution (3.536A). Similarly KG, Tsien, and Misek3 found an increase from 3.523 to 3.531A when nickel was carburized. strong4 studied the variation of nickel lattice constant as a function of dissolved carbon. However, in his case carbon was introduced into nickel by solidifying the melt at 65 kbar. Therefore, his carbon concentrations were much above the highest equilibrium solubility limit5 (2.7 at. pct C at 1 atm). Knowledge of the lattice mismatch between solute and solvent is essential in understanding the mechanism of solid-solution hardening. Therefore, we decided to determine the dilation of the nickel lattice by carbon under the more usual conditions of atmospheric pressure. The material used was Inco Electrolytic Nickel of 99.95 pct purity, as specified by the supplier. The impurity contents in wt pct were: Fe, 0.01; Cu, 0.01; Co, 0.03; 0, 0.005; C, Si, S, N, trace. To this base material various amounts of AUC-grade high-purity carbon were added during vacuum induction casting. Ingots, 2 in. in diam, were heated in a muffle furnace at 1000°C for i hr., hot-rolled to 1/2-in. thickness, and quenched into brine. All ingots with carbon concentration greater than 0.98 at. pct were enclosed in a cast iron box during the heating to minimize decar-burization. Small pieces were then either swaged down to 0.028-in.-diam wire or cold-rolled to 0.010-in.-thick sheets. After the final cold reduction in area of 50 pct, the specimens were recrystallized by heating in evacuated capsules at 1100°C for 60 to 80 sec and then quenched into brine. The final grain size was 50 to 100 µ. The carbon contents of the alloys, Table I, were determined by a combustion method

Jan 1, 1969

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By A. W. Schlechten, A. H. Larson

Equilibrium H2S/H2 ratios were determined as functions of temperature (500o to 900°C) and composition in a hydrogen-circulation apparatus. Within the composition range studied there exists a two-phase region of "Zr3S4" and "ZrS2". The upper composition limit of this two-phase region is hounded by a disulfide phase and is practically constant over the temperature range investigated. The lower composition limit of this two-phase region is bounded a "Zr3S4 " phase and varies appreciably with tem- perature. The upper composition limit of the homogeneous region of the disulfide phase is not definitely determined, but it appears to he bounded by the stoichiometric composition of ZrS2. The lower composition limit of the homogeneous region of the Zr3S4 phase could not he determined due to the extremely low values of the equilibrium H2S/H2 ratios. Various thermodynamic quantities are evaluated from the data. PUBLISHED free-energy data for the Zr-S system are practically nonexistent. Strotzer, Biltz, and Meisel1 measured the sulfur pressures for the reaction 2ZrS2(s) + S2(g) = ZrS3(s) in the temperature range 783" to 874°C. The average heat of reaction calculated from the temperature dependence of the sulfur pressure is -47 keal. It should be noted, however, that according to these investigators, the two-phase region as determined by sulfur pressure constancy under isothermal conditions extended from approximately ZrS2, 3 to ZrS2.7. From consideration of X-ray data they concluded that the homogeneous regions of the disulfide and trisulfide phases are ZrS1.8-2.0 and ZrS2.8-3.2, respectively. Hahn and coworkers2 have made a structure study of the zirconium sulfide phases. They summarized the zirconium sulfide phases as follows: the compounds ZrS3 and ZrS2 with narrow homogeneous regions, a "Zr3S4" phase with a homogeneous region roughly within the limits of ZrSl.5 and ZrSo.9, the compounds ZrS and Zr4S3, and a "Zr3S2" phase with a homogeneous region within the limits ZrSo.8 and ZrSo.5. It is noted that the compounds ZrS and Zr4S3 are only formed in the gaseous state through sublimation of a phase which has the approximate composition of the compound. This paper describes the determination of the stability of the zirconium sulfide phases by a hydrogen-reduction method in which hydrogen is circulated over the heated sulfide until equilibrium is attained. The resulting H2S-H2 mixture is then analyzed. Partial molar free energies, enthalpies,

Jan 1, 1964

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.&apos; When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By Bernard Kopelman

The particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by commercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature. and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. Review of the Literature Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.&apos; When reduction of tungsten oxides by H² was introduced Commercially,²,³ several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-l3 While these many investigations were in fair agreement on the equilibria WO³ + H2 = WO2 + H2O and WO2 + 2H2 = W + 2H2O there arose considerable controversy as to the chemical composition of the oxide between WO³ and WO², because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 100 years. Thus Malguti,14 in 1835, decided it was WO2.56 In 1857, Riche15 proposed the formula W³O8. Usler,16 in 1865, confirmed the existence of WsO8 and further proposed W1O1l. In 1897, Desil7 agreed upon W²O8 but also found W5O14.

Jan 1, 1947

By K. Tangri, M. Chaturvedi

On water-quenching from within the (a + ß) phase region Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys can undergo w transfirmation. This transformation has been attributed to the enrichment of ß Zr phase, at the solution-treatment temperature, by the solute atoms. The ß—w transformation is accompanied by a hardening 01 the alloys and in the optimum condition w-bearing specimens of the ternary alloy are about 14 pct harder than those bearing only a&apos; phase. On aging crl reverls thermally to more stable phases, which results in a considerable softening of the specirnens, as follows: w quenched -waged + ß Zr (enriched) waged - a + ß Nb The high-temperature bcc ß Zr in certain zirconium alloys can transform to a metastable w phase which has a primitive hexagonal structure. In the Zr-Nb alloy system w phase has been observed in the composition range of 7 to 15 wt pct Nb by a number of investigators.&apos;-&apos; In this composition range w can form by water-quenching ß Zr or by aging. known as athermal and thermal w, respectively. Hatt and Roberts&apos; have found that thermal w has a constant c/a ratio of 0.622 +0.002 regardless of the composition and tha: the lattice parameters are of the order of a = 5.02A and c = 3.0 ?. The actual lattice parameters depend upon composition and the temperature of aging. The lattice constants of athermal w. however, depend upon alloy composition.3 The presence of w phase in zirconium alloys can cause substantial strengthening which has been attributed as probably due to the coherency between w and parent ß Zr phase. Robinson et al.&apos; found that the presence of w can raise the strength of Zr-5.0 Nb-2.0 Sn and Zr-5.0 Mo-2.0 Sn alloys to about 170.000 psi: however. the ductility is considerably reduced. With the growing use of Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys in the nuclear reactors, and the significant effect of w transformation on the mechanical properties of zirconium alloys studies were undertaken to study the w transformation in Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys. This paper is concerned with the formation and reversion of w phase in these alloys. 1) MATERIALS AND EXPERIMENTAL TECHNIQUES The following two alloys were studied: 1) Zr-2.5 Nb-0.5 Cu (referred to as the ternary alloy): 2) Zr-2.5 Nb (referred to as the binary alloy). The chemical analysis of the alloys is given in Table I. The alloys, in the form of 3/8-in.-diam rods and 1/8-in.-thick sheets, were supplied by the Chalk River Nuclear Laboratories of the A.E.C.L. Initial fabrication for preparation of various specimens was carried out by cold rolling and swaging with intermediate anneals at 1000°C. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-% m of Hg. For optical metallography and hardness measurements disc specimens + in. diam by + in. thick were used. After the required heat treatments the specimens were mechanically and then chemically polished in a 45 pct HNO3, 45 pct H20. and 10 pct HF solution. The hardness measurements on the chemically polished specimens were carried out on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative hardness value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using copper K-a radiations in 114.6-mm-diam camera. Thin films for transmission electron microscopy were prepared by electropolishing heat-treated a by 7 by 0.005-in.-thick strips using a modified Bollmann-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol electropolishing bath was kepl at -5OCC and polishing was done at 5 to 10 v. The thinned specimens were washed in ethyl alcohol at -30" to -40°C and dried between filter papers. The thin films

Jan 1, 1970

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson&apos;s diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

By George L. Atwood, William Brown

Phosphate ore is being mined at Monsanto Co.&apos;s Henry mine, near Soda Springs, Idaho, for the company&apos;s three furnace elemental phosphorus plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. In stripping and mining, D-9 crawler tractors are utilized to rip and push-load rubber-tired scrapers. The equipment consists of six D-9G crawler tractors, four Caterpillar 657B scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12- month basis, two shifts per day, whereas mining is mainly in the summer months on a one-shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1 million tons of phosphate rock and 2.5-3 million cu yd of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor which owns, operates and maintains all equipment used. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis.

Jan 8, 1972

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.&apos; Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By S. LeFevre

THE solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covers briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results.

Jan 2, 1915

By N. A. D. Parlee, M. T. Utine

ThE kinetics of absorption of oxygen by induction-stirred liquid silver (at constant Po2 and T) has received some study here.&apos;&apos;2 This paper describes a study of the kinetics of effusion (non-bubble-forming), and some additional work on absorption. A Sieverts type of apparatus was used. The kind of reaction tube assembly has been described.4 The same 25-kw, 450-kc induction unit was used as in earlier absorption work1&apos;2 but the "coupling" was different. The runs were made under the following conditions: i) saturation at 1 atm, effusion at 0.81 atm;

Jan 1, 1969

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton&apos;s Laws to non-Newtonian systems have been examined in a previous paper.&apos; Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

An index covering the papers presented at the 19 Open Hearth Conferences from the first meeting at Pittsburgh, April 15 and 16, 1925, through the most recent meeting in Detroit, April 16 and 17, 1936, the reports of the meetings and the discussions that took place has been published, accompanied by a list of the papers presented, grouped by subject matter and a list of books of interest to open hearth men The list below gives the Open Hearth Conference meetings in chronological order and the symbols used to designate them in the index SYMBOL MEETINGS P25 Pittsburgh, April 15 and 16, 1925 C125 Cleveland, Oct 13 to 15, 1925 Ch26 Chicago, April 12 and 13, 1926 P26 Pittsburgh, October, 1926 B27 Buffalo, May 3 to 5, 1927 D27 Detroit, Nov 2 and 3, 1927 Y28 Youngstown, May 3 and 4, 1928 P28 Pittsburgh, Nov 15 and 16, 1928 C129 Cleveland, May 16 and 17, 1929 Ch29 Chicago, Nov 5 and 6, 1929 B30 Buffalo, May 20 and 21, 1930 C130 Cleveland, Nov 20 and 21, 1930 Ch31 Chicago, May 12 and 13, 1931- D31 Detroit, Nov 24 and 25, 1931 P32 Pittsburgh, May 24 and 25, 1932 Ch33 Chicago, June 29 and 30, 1933 P34 Pittsburgh, June 28 and 29, 1934 C135 Cincinnati, April 11 and 12, 1935 D36 Detroit, April 16 and 17, 1936 The list of papers mentioned in the first paragraph above is reprinted on pages 428 to 431 The Index of the Open Hearth Proceedings may be purchased at A I M E headquarters, 29 W 39th St, New York

Jan 1, 1936

By Herbert Everest

THE idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentage expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2: Development, including all necessary yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, drawslate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1 ½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the Beadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high.

Jan 1, 1916