Search Documents

By R. J. Allio, C. H. Randall

An automatic system for the quantitative analysis of microstrulcture has been developed. The method is based upon a statistical model of microstructure and employs phase intercept fractions as fundamental random variables. Structure-sensitive properties can be related explicitly to parameters derived from the distribution of phase intercept fractions in a matevial. THE properties of mechanical dispersions and of multiphase alloys art: intimately related to the amount, distribution, and intrinsic properties of the dispersed material. In many instances, the amount and distribution of the dispersed substances have greater influence on the over-all system properties than do the properties of the dispersed substance-Such properties as average particle size, particle size distribution, homogeneity of dispersion, volume per cent of dispersed phase, and mean free path between dispersed particles thus become critical in any evaluation of the properties of a dispersion. Unfortunately, techniques for evaluating quantitatively the microstructural characteristics of dis~ersions rapidly and accurately have not been available. If necessary, qualitative or semiquantitative devices can be utilized. Some such devices are based merely upon comparison of the specimens in question with arbitrary standards. Other techniques involve superposition of grids and tabulation of particles observed in different portions of the grid. Still other methods based upon lineal analysis entail counting lines or points at random upon the specimen to be examined; the number of intersections of the line with a given phase, the proportion of line or number of points which are covered by given phase are variously recorded. The mathematical basis for most of the techniques of quantitative metallography have been amply reviewed in the literature.'l2 without exctption, however, the standard techniques for quantitative metallography are either imprecise or are exceedingly tedious to apply. For example, tranverse integrating stage for rapid manual areal fraction measurement has been designed by Smith.3 Howerer, as in the case of any device based upon visual eslimation, operator bias may cause appreciable error. Various flying spot devices, on the other hand register particle size distributions in 2-dimensions, from which it is difficult to derive other properties of the dispersion. Thus, e.g., the 3-dimensional distribution cannot be inferred unless certain rather broad assumptions are made concerning the randomness of distribution and geometrical configuration of dispersed phase. Many limitations to the application of quantitative structural analysis can be overcome by the use of the microdensitometer, which is essentially an automated areal analysis device. Data obtained in the form of a distribution of phase intercept values are

Jan 1, 1962

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938

By F. W. Newhall

DURING the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Browns-ville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to the chairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corpora-tion, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which are presented in this paper. Acknowledg-ments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication.

Jan 1, 1934

By L. J. W. JONES, B. H. Bennetts

THE removal and disposition of large quantities of slag from blast-furnaces is a question of great importance in the design of works, and various methods have been devised, from time to time, in order to take the best advantage of local conditions. In blast-furnaces treating copper-ores or lead-ores, it is necessary to use a fore-hearth, or matte-settler, in order to collect, if possible, every particle of valuable matte which, otherwise, would be carried away with the out-flowing slag. In all of these cases, the slag overflowing from the fore-hearth is caught in pots and then conveyed to the dump. If the slag is of no value and the necessary water-supply, grade and dumping-space be available, the disposal of the slag by granulation is by far the cheapest and best method. It involves a minimum of labor, both at the furnace and at the dump; and it permits a continuous outflow of slag from the furnace- or settling-pot, thereby avoiding frequent tapping and plugging. When the conditions of water-supply, grade and dump-area will not permit slag-granulation, there are three other methods in common use. Large steel or cast-iron pots, or ladles, supported by trunnions on heavy cars which are moved by steam-, air-, or electric locomotives; some type of mechanical conveyor; and small pots or buggies moved by hand. The pots on the slag-cars are generally circular or oval in shape, and each one contains from 15 to 40 or more en. ft. of molten material. The mechanism for tipping them is more or less elaborate; and, as a general rule, the slag is dumped alongside, and quite close to, the track. They are more or less costly to construct and to keep in repair, and, in order to use them to best advantage, it is necessary to have a good elevation of track above the dumping-ground; furthermore, the rails must be of heavy weight, and well-supported on heavy ties. Other disadvantages of the slag-pots are-1, that the slag cannot be removed continuously

Mar 1, 1905

By Will H. Coghill, P. H. Delano, G. D. Coe

DATA concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as "grindability-index numbers," but grindability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pulverized product by a method comparable with commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulverizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation, it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-3/4 -inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horse-powerhours." The channel-roller pulverizer here-inafter described is believed to meet these requirements. HISTORY OF THE MACHINE The work started when Ralph W. Smith, engineer, St. Genevieve Lime Co., St. Genevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasiveness of dentifrices,1 and it was thought the same principles might be applied to coal. Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By John T. Popp, Jodi A. Rulli, Anthony T. Iannacchione

Anomalous geological features in the coal and surrounding strata of a mine in northern West Virginia have fractured and deformed an inherently weak roof rock prior to mining. Horizontal stresses, as much as six times greater than overburden related horizontal stresses, have induced cutter roof failure. This failure was distinguishable from rock deformation associated with geological anomalies because it was induced by mining. The characterization of these features has allowed for the prediction of zones of unstable roof rock and the determination of failure trends on gateroad stability. Geological anomalies included clastic dikes and a narrow zone of sandstone roof. Clastic dikes, representing intrusions of shale and claystone, were invariably accompanied by local roof rock instability, and often formed the boundaries of roof falls. Shale was the dominant roof lithology except where a small sandstone occurred in the northwest portion of the longwall mining area. The sandstone occurs in two phases: a sandstone-filled channel, 5-m- thick and 60-m-wide, which eroded and replaced the shale roof and the upper part of the coalbed; and a sheet sandstone unit which was crossbedded to interbedded with the underlying shale. Horizontal stresses are naturally relieved through the initiation of cutter roof failure. This failure may extend from a few meters to several tens of meters horizontally, and from a few centimeters to several meters vertically. Orientations of entries and crosscuts has a greater influence on the direction and total length of cutter roof failure at the rib-roof intersection than does the principal directions of the in situ horizontal stresses. Seventy-four percent of the cutter roof failures occurred along the rib-roof intersection. Orientations of cutter roof failure away from the rib- roof intersection were clustered in the north-south direction and may have been influenced by the horizontal stress field.

Jan 1, 1984

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By Louis A. Panek

Ground movements in the zone adjoining an active cave were measured at four sites in the San Manuel Mine. Measurements were made to detect extension and inclination, basic components of displacement, which can readily be duplicated by mine personnel using relatively simple equipment. The displacements demonstrated the development of a zone of strain relief surrounding the active cave, within which the ground tends to migrate toward the cave, and extension cracks develop tangential to the cave. This expansion of the ground surrounding an active cave can be exploited to promote future caving; it also creates special problems with respect to the design of an effective ground support system for mine openings in the production area.

Jan 1, 1981

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965

By Earl Bardwell

THE structural relations existing between cuprous oxide and copper -were first systematically studied by Heyn1', who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under. examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.-For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus is in place at this point.

Jan 7, 1913

By Larry Kaufman, Morris Cohen

THE solid phase equilibria' and the martensitic transformation in the iron-nickel system have been the subject of considerable study. In addition, there have been numerous investigations on the calorimetric and thermodynamic properties of iron-nickel alloys. The purpose of the present work is to extend the existing information concerning the martensitic reaction in the iron-nickel system, and to develop a general thermodynamic treatment which will encompass the equilibrium and non-equilibrium phase

Jan 1, 1957

By George M. Enos, Robert J. Anderson

This paper gives a summary of tests made on the accelerated electrolytic corrosion of the tin brass, 70:29:1 copper-zinc-tin (admiralty metal), of different grain sixes in various electrolytes. There has been great difference of opinion as to the effect of grain size on the corrosion rate of brass, particularly in condenser-tube practice, but so far as is known no information has been published on the subject. It has been assumed, on the basis of the amorphous-cement theory, that fine-grained brass would corrode more rapidly than coarse-grained because the amorphous phase is more soluble than the crystalline and there is more cement per unit area exposed in the fine-grained material. In previous work on the corrosion of metals and alloys in acid mine waters from coal mines,1,2 it was found that the grain size, within a restricted range, had practically no effect on the corrosion of the brass 70:29:1 copper-zinc-tin: In the tests made, samples of three grain sizes were included; viz., 0.025, 0.035, and 0.075 mm. diameter (1600, 817, and 177 gr. per sq. mm., respectively), and the average losses on exposure to the most acid of three waters were 7.07, 6.80, and 6.72 mg. per sq. cm. per day (24 hr.), respectively. No distinguishing features were observed on microscopic examination of the corroded samples. In two other mine waters, the corrosion losses were substantially the same for the respective samples. These tests were -incidental to other tests and were not sufficiently comprehensive to warrant drawing definite conclusions. In further work with the accelerated electrolytic corrosion test, as developed recently in the Bureau of Mines, tests were made

Jan 1, 1924

By C. C. Harris

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale-down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;'-' of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By Carl Allen

INTRODUCTION IN any discussion of mining one is repeatedly confronted with the difficulty of dealing with so many variable conditions. It is not an exact science and in the choice of a method each varying factor has a certain weight, which, in many cases, experience alone can determine. In mathematical terms, it is a function of many variables. A discussion of mining also loses much of its value unless, costs are considered, because the expectation of profit is the only excuse for carrying on mining at all. As conditions vary they cause fluctuations in cost and there are few operations to which a definite cost can be assigned. The character of the ore may make it difficult to drill, yet because of the ease with which it breaks the total cost of drilling and blasting may be low. In preparing this article the attempt has been, not to cover the whole field of mining, but to describe the different methods of stoping and mining which have distinct principles. In addition to this an effort has been made to show the advantage of dissecting the methods into their detailed operations and applying to these a mathematical study as an aid to the judgment in determining which is the best method to adopt, or in attempting to reduce the cost of a method already in use. Methods of mining include stoping, caving, and various methods of working large deposits which, in addition to the method of actually breaking the ore, require elaborate and definite plans of, development of the orebody. The ordinary methods of stoping are too familiar to all for any elaborate discussion, but it has seemed advisable to review the subject and give the principal advantages' and disadvantages of the different methods.

Jan 8, 1914

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930