Search Documents

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

[Cyanidation: Fresnillo, Mexico. 112. 734, 739. Abs.. YB84. 34 gold ore: before or after amalgamation. respective merita. 118, 538 high residue avoided by milling in water, 118, 542 Homestake mill, 112,607. 614 impoverishing gold ore before cyanidation justified. 118, 539 Kirkland Lake district, 112, 648, 649. Abs., YB84.32 literature prior to 1932. See Source Book. McIntyre Porcupine mines, 118, 638 mercury as an aid to extraction of gold, 118, 53 8]

Jan 1, 1936

Jan 1, 1969

By John D. Ridge, Robert C. Barwick

The amount of lead in concentrates that moved in international trade in 1952 was only 16 pct of the world mine production of lead and was less than 27 pct of the total of lead in concentrates and lead metal that traveled from one country to another. Because almost all lead is derived from galena, lead concentrates are high grade, with a theoretical maximum of 86 pct lead, and can be shipped as such without transporting a considerable weight of waste material. It would not be surprising, therefore, to find the large share of lead in international trade moves in concentrates (Rule 5). This is not, as has just been mentioned, actually the case. There is more than one explanation for the situation. Lead smelting is not a particularly difficult process and is one for which smelting equipment can readily be made of the best size for the tonnage to be handled. Another factor that encourages local smelting is the effort of many mining countries to see that a maximum of profit from their raw materials remains in the home country. Still another factor is the newness of large scale lead mining in two of the three largest exporters of lead in concentrates. In these countries, South West Africa and French Morocco, there has not yet been time to erect enough smelting capacity to process all of the concentrate output. Even in these countries, however, it will not be long, if present trends continue and plans are fulfilled, before most or all of the lead mined is domestically smelted.

Sep 1, 1955

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By Gary E. Melickian

Last year's review was characterized as a year of politics and began an era of legislation. The 1972 review can be similarly characterized, with even more rigid health and safety regulations and environmental legislation. The mining industry should be aware of what's happening in the nuclear power and other fields as a result of the National Environmental Policy Act (NEPA) of 1969, where the environmental impact of most major construction activities are already under close scrutiny. Section 102 of NEPA requires that all federal agencies include a detailed statement on specified environmental conditions as part of every report on proposed actions significantly affecting the quality of the human environment. All such environmental reports must consider the same general conditions: • The environmental impact of the proposed action. • Any adverse environmental effects which cannot be avoided should the proposal be implemented. • Alternatives to the proposed action. • The relationship between local short-term uses of man's environment and the maintenance and enhancement of long-term productivity. • Any irreversible and irretrievable commitments of resources which would be involved in the proposed action should it be implemented.

Jan 2, 1973

By L. G. Huntley

The occurrence of oil or "tar" in Mexico was mentioned as early as the seventeenth century by Friar Sagahun, who gives the Indian name "chapopote," by which these asphalt seepages are still called. This asphalt was apparently used, as it has been used by primitive people in many parts of the world, in religious ceremonies and for medicinal purposes. Travellers also report that the ruins in Yucatan and the pyramids in southern Mexico show traces of the use of "chapopotel' as a building cement.l DeGolyer says that the first attempt to exploit oil or gas in Mexico in a commercial way is shown by the records of the Memoria de Fomento of 1865, when permission was granted to a Senor Ildefonso Lopez to exploit the deposits of petroliferous substances in the San Jose de las Rusias area in the State of Tamaulipas. Other concessions follow, and probably refer to surface seepages which occur in that district. This was several years after the discovery of oil in Pennsylvania. In 1868, a well 125 it. deep was :drilled by a company organized in Mexico City, in what is now known as the,, Furbero district, and a little oil was refined there. In 1873, residents of Tampico denounced seepages along the Tamesi River, and asphalt was mined near Tempoal in the Canton of Tantoyuca. No drilling was attempted. But between 1880 and 1883 several shallow wells were drilled for oil in Mexico, two of them being near the present Potrero de Llano field west of Tuxpam. The wells were drilled by a Boston company with Canadian rigs, and are said to have reached a depth of about 400 ft., while one is reported to have flowed. Several other abortive attempts were made to drill for oil between 1885 and the beginning of the present century, about which time the Mexican Petroleum & Liquid Fuel Co., Ltd., in which Cecil Rhodes was interested drilled 24 wells unsuccessfully, several of them as deep as 1,500 ft., in the State of Vera Cruz. Also Messrs. Doheny and Canfield of California pur-

Jan 1, 1916

By Henry Lloyd Smyth

In 1891-92 1 was entrusted with the geological survey of part of the large area lying between the Marquette and Menominee iron-ranges in the Upper Peninsula of Michigan, and extending from the Republic trough on the north, through portions of the valleys of the Michigamme and Fence rivers, to and including the intermediate Felch mountain range on the south. Until a few years back the larger part of this area has been very difficult of access, and much of it is difficult still. The rock-surface is for the most part covered with swamp, forest and glacial deposits of various kinds, and therefore has not invited geological study. For these reasons the district, as a whole, with the exception of the Felch mountain range, remained almost unknown from a geological standpoint until our work in 1892. Our main object was to map the pre-Cambrian rocks, particularly the iron-bearing formations of Algonkian or Huronian age, and to obtain as much information as possible with reference to their sequence and structure, In carrying out this purpose, the use of simple magnetic instruments was found to be of the greatest assistance, and indeed indispensable. In this paper the results of our experience in tracing magnetic rocks by means of the disturbances produced in these instruments, have been brought together in systematic form, with such references to the particular area as are necessary in order to illustrate general principles, with the hope that they will prove useful to other workers in the same region, or in other regions where similar conditions may be encountered. The writer was efficiently aided in the field-work by Messrs. Samuel Sanford and Charlea N. Fairchild for nearly the whole period, and E. B. Mathews and H. F. Phillips for part of it,

Jan 1, 1897

By Henry Fay

The erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifing; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The extent of the erosion is greatest nearest the powder chamber, and diminishes toward the muzzle end.

Jan 1, 1917

By George J. Clark

One of the major problems of operation in the anthracite industry is the disposal and handling of refuse—not because of its complexity but because of the quantity and type of material involved. It is the purpose of this paper to describe the kinds of refuse, methods of disposal, quantities of material to be handled and equipment used, together with present day application at specific operations in the Northern, Eastern Middle, Western Middle and Southern anthracite fields. For the purpose of this paper, refuse is considered to be any material that has no present or foreseeable future value and that must be handled and disposed of in the process of mining and preparing anthracite for market. Included in this classification are tunnel rock, mine rock, cleaner plant refuse, breaker refuse, old timber, ashes and silt. Disposal Methods Old timber is disposed of either by burning or by depositing on the refuse bank. Burning is preferred because timber on the refuse bank is a potential fire hazard. Ashes are deposited on a separate bank, mixed with other refuse, or flushed into old mine workings. In many places, the latter practice has caused considerable difficulty in preparation of coal mined from these areas. In depositing ashes on the surface, it is wise to refrain from mixing them with material containing coal as such contamination may prevent reclamation of the coal in future years. Tunnel work, mine rock, cleaner plant and breaker refuse compose the bulk of the material to be disposed of and handled, and are referred to collectively as "refuse" in this paper. Waste material in or adjacent to the coal beds may be removed at the working face wherever possible. This can be done in flat or lightly pitching beds, and in the Northern field represents a sizable percentage of this type of refuse handled. In the other three coal fields, this method of disposal cannot often be used. Refuse not removed at the working face is taken to the surface and generally is deposited on banks; occasionally it is crushed and flushed into old mine workings. Breaker refuse often is used for constructing berms for silt-retention basins. Disposal Problems The problem of handling refuse is different for each operation, owing to topographical conditions, quantity of material to be handled, anticipated requirements and types of equipment in use elsewhere at the operation. Preparation plants with limited refuse-disposal areas, excessive grades to reach the required elevation and long hauls to disposal areas not readily accessible require the selection of equipment to best meet the conditions. The quantity of refuse to be handled from a given amount of raw material varies considerably throughout the four fields. In mine coal, this varies from a low

Jan 1, 1949

By F. W. Schroeder

AT the annual meeting of the Institute 2 years ago, a paper,1 " Requirements of Refractories for Open Hearths," was presented by F. W. Davis and G. A. Bole of the U. S. Bureau of Mines. In a brief foreword, D. A. Lyon stated that the paper was not to report the results obtained but rather to present an outline to serve as a basis for discussion. The essential parts of an open-hearth furnace were described and the conditions under which they operate. Some constructive discussion followed the reading of the paper. One of the first fellowship investigations undertaken by the Bureau of Mines in 1924 under the cooperative agreement with Carnegie Institute of Technology, through the Metallurgical Advisory Board, was to determine service conditions of open-hearth refractories. The present paper gives the results of this work which was done in the Pittsburgh district and was in charge of the authors. Material contributions in the form of data were contributed by E. N. Bauer, J. W. Campbell, G. H. Pfeiffer and A. Grodner, Carnegie Institute of Technology research fellows. The study covered 18 mos.

Jan 7, 1926

By David Scott

THE MOGOLLON mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately. $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent, of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. LOCATION AND TOPOGRAPHY The town of Mogollon is 75 mi. (121 km.) by a poorly located highway from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western-slope of the Mogollon Range. The main canyons run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the

Jan 2, 1920

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

The Climax design is for the human being and his needs. Climax President Arthur Bunker has likened the high mountain operation to a giant, 250 million tons in weight, and 12 thousand feet high. No matter how huge or complicated the plant, the design must assure efficient operation by its human operators. By the same token, living and playing facilities must be designed for fullest satisfaction in use-else the capital investment is not justified. Even the product, molybdenum, finds its application through the ever growing demands of a highly industrialized society of humans. Research in Climax Laboratories, in tune with our technical age, helps guide molybdenum to its maximum use for society.

Aug 1, 1955

By Nathaniel Arbiter, Chas. H. Behre

Two outstanding factors characterize most undertakings in the mineral industries: (1) mineral deposits are not equally distributed over the earth but are localized by natural processes, and (2) the mineral industries are largely based upon wasting assets. Neither of these factors is invariably true, for a few mineral materials, such as water, are essentially world-wide and others are replaced periodically by processes not unlike crop production. Indeed, with some, such as the salts in the sea, the supply is cyclic in short or long periods, whereas others, like water, though locally or periodically in short supply, are essentially inexhaustible. But to the extent that most minerals are limited to certain areas and are "permanently" consumed, any industry founded upon them, by implication, demands great care in planning for the most effective extraction-the essence of wise and conservative expenditure. Several less unusual yet also truly fundamental factors in the economics of the mineral industry are those involving (1) the various kinds and properties of mineral materials, which influence their use; (2) their geologic and geographic availability; and (3) the 'techniques unique to their discovery, exploration, and utilization. This chapter is designed primarily as a brief background for later ones and as a summary of the several unusual or at least special factors and of their effect upon the economics of the mineral industry. The social and political and especially the economic aspects of the industry are the main subjects of this volume and are dealt with in extended fashion in subsequent chapters. Fundamental Characteristics of Mineral Deposits DEFINITIONS Minerals are naturally occurring compounds of nonliving matter, each technically defined as having ( 1 ) a chemical composition that may vary

Jan 1, 1964

By AIME AIME

S ULFURIC acid made in the United States during the last four years has averaged approximately 7,000,000 tons of 50" B6 acid a year. This is double the production of the year 1913. About 66 per cent of the acid is made from sulfur, 16 per cent from pyrite, 13 per cent at copper, lead, and zinc smelters, and the remainder from miscellaneous sources it her the chamber process or the contact process, (at some plants both) is used. In 1923, the contact process accounted for nearly 30 per cent of all the sulfuric acid made in this country and since then it has been increasingly employed. It was first introduced here in 1898, and has always .proved less expensive than the chamber process for the manufacture of .acid of high concentration and purity, but the latter produces acid of low strength suitable for many industries.

Jan 1, 1929

By Franklin Bache

THERE seems to be in the public mind, and even in the minds of some coal-operators not experienced in mines subject to dust-explosions, a feeling that there has been something mysterious at the bottom of a number of recent American colliery-explosions. It has been declared in cases of accidents in mines regarded as particularly well equipped, in which every preventive precaution was said to have been taken, that the explosions were incomprehensible, and resulted from causes beyond the present knowledge of the practical coal-operator. But it is safe to say that no explosion has taken place which could not be explained by reasons well understood by most operators. The LT. S. Geological Survey Test Laboratory, recently inaugurated at Pittsburg for the reported purpose of investigating scientifically the matter of explosions in mines, will discover no new explanation of explosions. It call, however, co-ordinate the previous investigations of similar boards in England and on the Continent; and it may do a vast amount of good by promulgating widely, and in a form comprehensible by the most unlettered miner, certain facts and obvious deductions that cannot but have an effect in reducing the number and extent of the mine-disasters which, in the last few years, have been so terrible in frequency and magnitude. The only possible sources of explosions of any magnitude in coal-mines are : (1) explosives stored in quantity in the mine; (2) gases generated or liberated in the mine; and (3) coal-dust. Combinations of any of the three may, of course, take part in the result. The danger of any great loss of life from stored explosives alone is very remote. The simplest ordinary precaution forbids the presence, in one place underground, of any considerable quantity of explosives, and it would require an

Aug 1, 1909