Search Documents

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to 'i), there were also other sessions of interest' to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,' the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By W. Ivanick, Frank W. Glaser

ORDERING reactions of Fe-Si compositions in the a region have been mentioned in a number of review articles.7-8 However, little is known in regard to the critical temperature, T at which this transformation takes place. Greiner and Stoughton,' in a study of the constitution of iron-rich Fe-Si alloys below 800°C, placed the onset of order at a composition of about 4 to 5 wt pct (7.5 to 9.5 atomic pct) Si. They observed that at this composition the ductility and strength begin to decrease sharply and brittleness develops. During X-ray studies they observed only the appearance of superlattice lines for compositions containing 12.5 atomic pct Si. More recent X-ray diffraction studies- etected the appearance of superstructure lines (corresponding to the calculated positions of [Ill] and [ZOO] reflections) for alloys containing 9.5 atomic pct. This fact confirms Greiner and Stoughton's original hypothesis in regard to the onset of order at compositions containing about 7.5 to 9.5 atomic pct Si. The physical properties.of Fe-Si alloys containing more than 10 atomic pct Si have been studied only to a limited extent. Their extreme brittleness and difficulties of sample preparation render them of little industrial use in comparison with alloys in the 0 to 10 atomic pct Si range. The properties of Fe-Si alloys reported to date are mostly properties measured at room temperature on ordered compositions It appears that because of experimental difficulties fully disordered alloys could not be produced in the critical composition ranges and their properties could therefore not be reported. In Figs. la, lb, and lc, a summary of physical properties of Fe-Si alloys, measured during recent investigations of the influence of silicon additions to iron, is presented. No mention of determination of the critical temperature, T for disorder could be found in the literature. The following is an account of work done in an attempt to: 1) produce the disordered state of various Fe-Si alloys and establish the critical temperature, T for disordering, and 2) compare the electrical and thermal conductivity characteristics of the ordered and disordered phases as functions of composition. Materials, Preparation of Test Samples, and Testing Methods Fe-Si alloys with high silicon contents (about 10 atomic pct) are usually prepared using powder metallurgy techniques. This method insures accurate compositions and high purity through the use of protective atmospheres during solid state diffusion alloying of the mixed powders."" Iron and silicon powders were mixed in the desired proportions, cold or hot pressed, and then homogenized at 1150°C for periods ranging from 6 to 12 hr under a protective getter and in a hydrogen atmosphere. Fully homogenized samples were quenched in water from various and successively higher temperatures to establish the critical temperature for disorder. Temperatures were determined using Pt—Pt-Rh thermocouples in contact with the test samples. Test bars were approximately 0.6x1.25x7.5 cm. Electrical measurements were made at room temperature by determining the potential drop over a 1.5 cm span for a current of 10 amp. Densities of the samples were determined by immersion. High temperature electrical resistivities were measured using previously described techniques.'" Specific heat conductivity up to 200°C was measured by heating one end of the test bar and water-cooling the other; heat conductivity was then obtained by subtracting the rate at which heat entered the water from the

Jan 1, 1957

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By T. D. Yensen, N. A. Ziegler

The elements aluminum,' arsenic,2 silicon,3 tin2 and vanadium,~.~ when used in relatively small amounts as alloying elements, seem to have a beneficial effect on the magnetic properties of iron—i. e., they increase the maximum permeability and decrease the coercive force—whereas there are definite indications that boron,5 carbon,6 nitrogen: oxygen," phosphorus16 sulfur6 and titaninum,~ as well as the metals of and adjacent to the ferromagnetic group, nickel,~ cobalt,1° copper," and manganese,% have a detrimental effect on these properties. The effects of calcium4 and magnesium4 are small, if any, while the effect of chromium12 in small amounts is unknown and in large amounts is generally detrimental. WeveR's Classification13 All chemical elements may be divided into three classes based on their effect on the allotropic transformation points of iron. Class 1 contains the nonmetallic elements (except phosphorus) and these lower the A3 point and raise the A4 point. Class 2 contains the common metals and

Jan 1, 1931

By Percy A. Robbins

I. INTRODUCTION. THE central power-station. of the De Beers Consolidated Mines, Ltd., was designed and built under my supervision about five years ago. Since no detailed description of this plant has ever appeared, it may possess sufficient interest to warrant its publication, even at this late date. Although some additions may have been Blade to the plant, the following account, prepared from my notes, and accurate up to May, 1905 (at which time I severed my connection with the De Beers Com¬pany), will, I think, be found substantially correct. Certain local conditions governing the design of this plant should be stated first. If. GENERAL CONSIDERATIONS. The climate is hot and dry. The .region around Kimberley is arid and water is very scarce. The supply obtained from the mines contains so much material in solution that it is unfit for use in boilers or condensers (although tests recently made with a water-softening plant, built by Hans Reisert, of Germany, would indicate that water thus treated is suitable for boilers). And the amount of water required for concentrating about 30,000 tons of ore per day is so large that the question of adequate water-supply for this power-station had to be carefully considered. The rainy season extends from December to April, and the rainfall averages about 15 in. per year. Droughts are frequent; and in some years there is scarcely any rain at all. The water-supply for the town of Kimberley is brought from the Vaal river, 16 miles distant, and pumped into town by a private water company. The charge made for water, which is

Mar 1, 1908

By R. F. Mehl, C. E. Birchenall

R. E. Hoffman and D. Turnbull—The authors have presented evidence which they have interpreted as indicating that the rate of self diffusion is not intrinsically more rapid at grain boundaries than within the grain. Grain-size effects which apparently exist are attributed rather to impurities concentrated at the grain boundaries. In view of our own experiments and the existing evidence, we believe that the support for this hypothesis is not convincing. We have in progress an investigation in which the rate of self diffusion of silver is being measured over an extended temperature range in both single-crystal and polycrystalline specimens. The results of the single-crystal experiments and some preliminary data on fine-grained polycrystalline specimens have already been reported:' and it is anticipated that a complete report will be published in the near future. The self-diffusion coefficient of large-grained polycrystalline silver (1 grain per sq mm) has previously been measured by Johnson" between 730" and 940°C. The diffusion coefficients which we have measured in single crystals (210 plane normal to diffusion direction) agree within experimental error with values calculated from an extrapolation of Johnson's curve down to temperatures as low as 500 °C. However, it has been demonstrated that the overall self-diffusion rate in fine-grained polycrystalline specimens (initial grain size of 0.003 cm) becomes measurably larger than the overall rate in a single crystal at a temperature of 600°C, and the discrepancy between the two rates becomes greater as the temperature is further decreased. In fact, it has been possible to obtain satisfactory penetration curves for polycrystalline specimens using the sectioning technique at temperatures as low as 400°C. At this temperature, the penetration is 50 to 100 times greater in the polycrystalline specimens than in a single crystal. Fisher" has developed an analysis whereby the ratio of the rate of the unit diffusion process at the grain boundary to the corresponding rate within the grain can be calculated from the penetration curves and an assumption as to the width of a grain boundary. This analysis applied to our data indicates that the unit process at the grain boundary is faster by a factor of 10' at 475°C when the grain boundary width is taken to be 5. The silver used in most of these experiments was obtained from the Handy and Harmon Co. and listed as 99.97 pct pure. Preliminary experiments on 99.999 pct silver from the Jarrel-Asch Co. indicate a grain-size effect of the same order of magnitude as in the less pure silver. Nominally, these purities are as good, at least, as that of the carbonyl iron used by the authors, but of course if an impurity effect does exist its magnitude might be very dependent upon the nature of both major and minor constituents. The authors have cited the work of other investigators who have found no grain-size effects. Neither Steigman, Shockley and Nix" nor Maier and Nelson8 were able to correlate self-diffusion coefficients of copper with grain size. However, all their measurements were performed at or above 750°C; and on the basis of our work with silver, no grain-size effect would be expected at temperatures above about 0.7 of the absolute melting temperature unless the grain size were exceedingly small. Likewise, in the investigation of the self diffusion of lead by Seith and Keil,14 the lowest temperature at which the diffusion coefficient was measured in polycrystalline specimens was 207°C, which is still sufficiently high so that the lack of a grain-size effect is not surprising. Finally, in those experiments on iron from which they concluded that there was no grain size effect, Drs. Birchenall and Mehl seem to have no information as to the actual grain sizes immediately prior to and following the diffusion anneal. Without this information, we believe that their own experiments offer little support for their hypothesis. F. S. Buffington, I. D. Bakalar, and M. Cohen—The results given in this paper agree in order of magnitude with those tentatively reported by us.27 However, significant differences exist in the two sets of data, and it may be well to make an explicit comparison. The diffusion studies at M.I.T. were conducted on somewhat higher purity iron (99.98 pct Fe) than the grades used by the authors, but this is undoubtedly not the answer. Fig. 4 shows the diffusion results of both laboratories for the gamma phase, omitting the authors' data on the commercial steels, while fig. 5 presents a similar comparison for the alpha phase. The divergence is much more marked in the latter case than in the former. In connection with the M.I.T. determinations, all of the runs in the gamma range and those above 800 °C in the alpha range were conducted with specimens having a relatively thick (0.002 cm) electrodeposit of radioactive iron. This practice minimizes any possible error due to extraneous diffusion that may occur during the heating to and cooling from the operating temperature. An exact solution of Fick's law for these boundary conditions was used in calculating the diffusion coefficients. At a later time, three runs were made below 800°C, using very thin electrodeposits similar to those of the authors, and the points fell considerably below the values expected from the extrapolation of the results based on the specimens with the thick deposits (compare dash-dot line in fig. 5). However, in the runs with the thin deposits, deviations of 100 pct were found between the individual specimens, whereas the maximum deviation with the thick deposits was less than 25 pct. Accordingly, it is not known at the moment whether the M.I.T. points below 800 °C should be given as much weight as those above 800°C. If this were done, the frequency factor would be of the order of 400 cm2 per sec, which is quite high. In other metals, the frequency factor for self diffusion lies between about 0.1 and 10 cm2 per sec. As the points below

Jan 1, 1951

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By John Wulff, J. H. Hollomon

The opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was re-deposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May16 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to a1pha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,a in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As2O3),

Jan 1, 1942

By John Wulff, J. H. Hollomon

The opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was re-deposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May16 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to a1pha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,a in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As2O3),

Jan 1, 1942

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By Gifford E. White

EXPLANATIONS of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several places.1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,4 the transient potential resulting from a suddenly applied steady voltage is the indicial transfer function of Carson,5 which has been extensively studied in network theory. [ ] The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a [ ] pair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G1 and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential circuit terminals, giving the time function that has been called A(t).4 This time function has been solved for analytically in the case of a homogeneous earth,6,7 and the

Jan 1, 1941

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.'?,' "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By Walter Kauzman

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications.1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By D. A. Flanagan, B. L. Landrum, P. B. Crawford, B. C. Norwood

Herern is described a heat conduction model which has been developed to predict the pressure distribution within a reservoir being subjected to rrnsteady-state depletion. Although potentiometric models have been widely used to study reservoir pressure distribution, their application is limited to the study of steady-state cases. Electrical analyzers may be used to study unsteady-state phenomena, but their application and simulation have certain limitations. Much of the now accepted theory of unsteady-state fluid flow in porous media has evolved from previous heat conduction knowledge. An analogy between the flow of fluid in an unsymmetrical reservoir and con-duct ion of heat in a similarly shaped unsymmetrical metal plate is made to show adaptability of the hear conduction principle to transient reservoir cases. A description of the model and necessary instrumenrarion is included. Data show influence of well location on pressure distribution during unsteady-state deple[ion. Application of results is made to a hypothetical reservoir and to a reservoir located in an irregular aquifer. INTRODUCTION Development of methods for predicting behavior of petroleum reservoirs has resulted partially from adaptation of electrical and thermal flow concepts to the flow of fluids through porous media. Extensive investigation of electrical and thermal flow problems has resulted in mathematical solutions applicable to many reservoir problems. The relative ease of measuring electrical flow has brought wide acceptance of the use of the potentiometric model to study certain field problems. Potentiometric models are restricted to the study of steady-state conditions because of the instantaneous response of electrical flow to changes in the applied potential. The electrical reservoir analyzer has been one of our most useful instruments for studying certain phases of unsteady-state behavior1. Other than approximation techniques, no method exists for determining pressure distribution in an irregular reservoir during primary depletion. Heat flow, like fluid flow, is inherently transient. The model described here was developed to use this transient nature of heat flow, measurable in the laboratory, to simulate transient flow of fluids in the porous medium of the reservoir above the bubble point. A metal plate shaped like the reservoir to be studied was heated by a "well" source. Temperature increase in the plate is analogous to pressure decline in the field if the field is being depleted, or pressure increase if fluid is being injected. This study is intended to determine the feasibility of using the transient nature of the heat flow to study the transient behavior of fluid flow. It is hoped that this new technique will aid in the understanding of one of the more complex phases of reservoir engineering. THE FLUID FLOW-HEAT CONDUCTION ANALOGY The similarity of the equations which describe the flow of fluids through a porous medium and the conduction of heat through a solid is well known2. Rate of flow of fluids is given by Darcy&apos;s law3. while the rate of flow of heat is given by Fourier&apos;, (I,, - KA 4T........(2) Combining Eq. 1 with the equation of continuity for a compressible liquid", i.e.,results in Expressing y in terms of the compressibility, i.e., pr = peey ,..........(5) and by expanding the exponential and neglecting higher orders of cp one can obtain

By Charles Jones

IN the winter of 1902, while occupying the position of mining and examining engineer for the Mountain Copper Co., Ltd., of Keswick, Cal., I had occasion to discuss with the General Manager, among other things, the question of the enormous waste of sulphur in smelting cupriferous, pyrite ore, and to cast about for means to utilize this waste or to render the fumes innocuous to vegetation. The decreasing rate of production of California farms, the consequent need of fertilizers, and the opportunity thus offered to utilize large quantities of sulphuric acid in the manufacture of superphosphates naturally brought the subject to the practical and commercial side of phosphates. I was informed that the company had made efforts to find phosphates in the West, without success. I advised as a start placing inquiries for phosphate deposits on the Pacific coast in the current mining ,journals. This was done, with the result that in January, 1903, from an advertisement in the Mining and Scientific Press we got track of a deposit in Rich county, Utah, through T.J . Wilson, of the Southern Pacific railroad in San Francisco. As soon as snow in the mountains would permit, in May, 1903, I undertook an examination of the property, with the result of recognizing the importance of the find, in spite of its lack of facilities for transportation at a commercial figure. On June 15, 1903, I concluded my report by saying, "This may be one of the world&apos;s deposits of phosphates." On Nov. 17, 1903, I concluded my report for the season in the following words : " I have now no hesitation in saying that I believe the Carboniferous formation so largely developed in the Wasatch mountains of Utah and the mountains of the Great Basin will prove to be one of the greatest storehouses of phosphoric acid in the world."

Jan 10, 1913

By Dan White

Stress measurements taken at Climax, El Teniente, Henderson, Lakeshore and Urad mines indicate that the deposits cited are generally subject to an inclined stress field that can be highly anisotropic. The horizontal stresses vary significantly between deposits and exceed the measured vertical stresses at Henderson and El Teniente mines. Experience at Henderson, Lakeshore and Urad mines is used to suggest a relationship between cavability and the premining stress. In poorly fractured, high strength rock masses, high stresses can assist the caving process. In well fractured, low strength rock masses, caving is ensured by breakage along fracture planes. The relationship between ground weight and the premining stress is also investigated. Ground weight problems appear to be most related to the competence of the ground rather than the magnitude of the premining stress as supported by experience at Climax and El Teniente mines. Recent developments in block caving favor the extraction of poorly fractured, high stressed rock. Accompanying the development of these deposits are new problems such as rock bursts. These pose particular problems to mine designers in that no experience currently exists in combatting rock burst problems at block caving mines.

Jan 1, 1984

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I &apos;hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years&apos; time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By Ronald J. McGregor, Anton R. Hendriksz

INTRODUCTION The NIMCIX contactor was developed in the late sixties at the National Institute for Metallurgy in South Africa, for the main purpose of extracting uraniuy from relatively low-grade uranium solutions. &apos; The concept was sufficiently developed by 1974 to permit the operation of a 1500 litre per minute column to treat unclarified urgnium-bearing solution under industrial conditions. The plant operated so successfully that several large-scale units have subsequent18 teen constructed and are operating efficiently. &apos; Total resin consumption figures as210w as 3 per cent per annum have been reported, and the extraction efficiencies of the installations have been exceptionally good. All the solutions treated have been acidic in nature and in every case have been of such a nature as to significantly depress the maximum uranium loading on the resin beads. The chemical constituents of the leach solution fed to the loading column determines the ease with which the soluble uranium can be absorbed by an ion exchange resin. The concentration of competing ions and various resin foulants define the nature of the continuous ion exchange equipment required for efficient extraction performance. The basic NIMCIX concept is retained in these various alternate designs, but batch or continuous elution methods with fully automated or manual control systems may be selected for the different process solution conditions. BRIEF DESCRIPTION OF THE NIMCIX CONTACTOR The NIMCIX ion exchange column is a multi-stage fluidized bed contactor which is designed to permit a counter-current flow of solution and resin in order to maximize extraction efficiency. The flow o resin is periodic, based on the Cloete and Streat 5 principle of reverse flow. The basic operating cycle can be divided into five periods, as illustrated in Figure 1. For the purposes of describing the cycle, the loading column is considered; how- ever, a similar sequence may be applied to the operation of a NIMCIX continuous elution column. S&apos;I&apos;EP 1: During the forward flow period, Solution flows up through the column and fluidizes the resin contained in each stage. The uranium depleted solution overflows the upper flared-section of the column as the tail solution. Step 2: The flow of solution to the column is temporarily stopped and the resin is allowed to Settle onto the plates in the column. STEP 3: During the reverse flow period, a fixed volume of solution is drained from the column to the transfer vessel. This flow causes resin transfer to occur from stage to stage and also out of the bottom stage. At the end of this period, which expires when the low level switch (LS) is actuated, some of the resin is left in the conical section of the column and the pipe interconnecting the column and the vessel. STEP 4: The cone flush period ensures that all the resin left in the cone of the column and the pipe is transferred to the transfer vessel before forward flow commences. STEP 5: The loaded resin in the transfer vessel, which has been isolated from the column, can either be hydraulically transferred to the top of the elution column or eluted in the vessel before being transferred to the top of the loading column. The major advantages associated with the NIMCIX concept are: (i) Simple method of operation (ii) Contactor can readily be scaled up to large diameters. (iii) Because the resin does not pass through pumps or airlifts, and valves cannot be closed on resin beads at any time, the resin losses are exceptionally low. (iv) Operating costs are low. (v) Relatively few valves in the system. (vi) Stable operation is achieved over a wide range of feed rates and concentrations.

Jan 1, 1980

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.&apos;l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1&apos; to ensure axial application of the load. The rate

Jan 1, 1942