Search Documents

By Royal Jackman

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investiga-tions. The development of X-ray examination of minerals and improve-ment in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investi-gators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation.

Jan 1, 1933

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condi-tion, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organiza-tions of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements.

Jan 1, 1938

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage,-and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation. INTRODUCTION Cornucopia is in the southeastern part of the rugged Wallowa Moun-tains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal.

Jan 1, 1939

Jan 1, 1902

By E. S. Davenport, R. J. Hafsten, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By R. J. Hafsten, E. S. Davenport, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

[Pumps: oil-well: plunger: essential parts, G26, 130; 74, 828 improved type, 74, 846 leakage, 74, 837 operating cycle, 74, 833 Uren design, G26, 145 sucker-rod failures, G26, 136 sucker-rod stress, 74, 835 sucker rods, 74, 830, 832 tubing, 74, 833 tubing difficulties, G25, 138; 74, 836 Olivite, 73, 337 valve and seats, 74, 832 Punching: Monel metal, 78, 86 nickel, 78, 86 Punjab. See Indian Empire. PUPIN, M. L biography, M26, 113 John Fritz medalist, 1931, M81, 499 recipient of Washington Award, M28, 155 PURDY, R.: Discussions: on Relative Efficiencies of Domestic Fuels in Relation to Their Costs and Their Advantages 108, 353 on Uses on Coal in the Ceramic Industry, 108,389,398]

Jan 1, 1936

By M. P. Tixier

In several log interpretation methods, water saturation is evaluated by use of the ratio of the readings of a short spacing resistivity device and a long spacing resistivity device plus information on the mud filtrate and connate water resistivities, which is often derivable from the SP. These methods are valid over a certain range of conditions, usually specified by moderate invasion and R.. greater than R,. Since these methods involve no explicit evaluation of the formation factor, F, the saturafiion so found may be used in the standard Archie equation to derive a computed formation factor which, as a check, may be compared with the formation factor known from other independent measurements. Discrepancies in the two values of formation factor generally indicate that the ratio method is not within its range of applicability. If the computed F is too low, the corresponding S, is too low; if the computed F is too great, the corresponding S, is too great. By means of this "porosity balance" check, and some knowledge of the probable conditions of invasion, the interpretation can often be improved. The poqosity balance check is discussed for the cases of the Induction-Electrical Log Interpretation Method, the Rocky Mountain Method, and the R.,/R, Method. For the first method, a discussion is also given for the case of shaly sands. INTRODUCTION Al though many logging tools are available to obtain a practical value of porosity, the only logging method reflecting the water saturation is electrical logging. Water saturation is commonly computed from electrical log data by means of the basic Archie formula, Where F is the formation factor, R, the resistivity of the formation water, and R, the true resistivity of the formation. One difficulty in this procedure is a possible error in the evaluation of R, from the logs— for example, in the case of very deep invasion. There is no possibility, inherent in the procedure, which would provide a check of the accuracy of R, and, hence, of the computed saturation. Other approaches have been proposed which are based essentially on the ratio of the readings made with two dzerent devices: one device, with a short radius of investigation, provides a value close to the resistivity of the invaded zone; the second device, with a long radius of investigation, gives a value close to the true resistivity of the bed. By these methods, the determination of saturation is made independently of any direct knowledge of the formation factor. Therefore, if the formation factor (or porosity) is known from other sources (core analysis, neutron log, MicroLog . . .), it becomes possible to take advantage of this additional information in order to check the value of saturation derived from these latter methods. Inasmuch as this proposed check procedure relies on a knowledge of the value of formation factor or porosity, it has been deemed appropriate to call this verification a porosity balance. The purpose of this paper is to discuss the principle and the application of the porosity balance, depending on the method of interpretation being used. Basis of the Method There are in existence three interpretation methods by means of which the water saturation can bc found without a knowledge of the formation factor (or porosity). As just stated, they are based on the fact that the ratio of the two resistivities (one measuring the resistivity close to the hole, the other measuring the resistivity far from the hole) is independent of the formation factor since it affects the two resistivity measurements in the same way. Chronologically, the resistivity ratio methods are: (1) the Rocky Mountain Method, which has been used since 1943 and was explained in a paper in 1949;' (2) the R../R, Method or Shaly Sand Method, presented in 1954, which permits the calculation of the water saturation in both clean and shaly sands2; and (3) the Induction-Electrical Log Method, presented in 1957 for the interpretation of the induction-electrical log combination." Each method requires certain definite conditions in order for the interpretation to be reliable. The porosity balance method will let us know whether these conditions are fulfilled. In clean formations we know that the fundamental Archie relation (Eq. 1) must always be verified. This relation can be rewritten:

Jan 1, 1951

W. L. Saunders, New York, N. Y.:—Mr. Parker's paper, though entitled Conservation of Coal, might also be called the Conservation of Life in the Coal-Mines of the United States. No subject is of greater importance to mining-men at the present time than information from experts as to how to save coal and how to save human lives in mines. That the casualties in the coal-mines should exceed 3,000 in the year 1907 is simply appalling, and that 1,000 men should have been killed in a single year through explosions alone, and that so good an authority as Mr. Parker should say that " a prolific cause " is an "improperly-prepared blast" or "the failure on the part of the miner to undercut his coal," points to the importance of activity not only among mining engineers but also, through experts, by the legislatures of the respective States. There is but little doubt that nearly all the serious coal-mine

Jan 1, 1910

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By Robert Bell

THE " Tar-Sands." is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Athabasca. Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really clip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Mar 1, 1908

By Ogden B. Malin

In conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructures of several compositions under various conditions of working were examined in an effort to establish this as a fact. Survey of Previous Work in Studying Extrusion Defects Very little has been published concerning defects in extruded and forged brass. In 1921, R. Genders1 $ delivered a paper before the British Institute of Metals, relative to a defect inherent in the extrusion process. This defect, commonly found in extruded brass rod, shows up in the form of a circle in a transverse section consisting of oxides and impurities, and is generally present in the last 25 to 30 per cent of the rod. Genders concluded that the defect is caused by the turning inward of the skin of the billet at the edge of the plunger because the inside of the billet is more plastic than the outside, which is in contact with the cooler container; the outside skin will lag behind to form the rear end of the rod. Genders suggested a movable die as a remedy, and while this met with fair success, it is not used in present practice. About the same time as Genders' experiments, Tucker2 and Rosen-hain3 conducted experiments using colored plasticene in the form of a billet, and found much the same defect as Genders. Dr. Rosenhain State College, Pa.

Jan 1, 1932

The organization of the American Institute of Mining Engineers, 75 years ago, parallels the beginning of present-day steel-producing methods in the United States. This early association with the industry is emphasized by the fact that the first open-hearth furnace constructed and operated in this country was then only three years old, and the first commercial bessemer converter was just seven years old. Total steel production in the year 1871, as recorded by the American Iron and Steel Institute, was 84,000 net tons, of which 2,000 tons was produced by the open-hearth process, 45,000 tons by the bessemer, and 37,000 tons by the crucible, puddled iron, and other processes. The bessemer process had thus become the major source of steel production. Its capacity expanded progressively during the following decade, and by 1880 was the source of approximately 86 pct of total steel production. Most of this tonnage was made in eastern Pennsylvania and used in rail manufacture. At about this time, however, important changes began to occur which gave impetus to the production of steel on a much larger scale. The development of Lake Superior ores from 1870 to 1890 and the exploitation of the Mesabi Range in 1892 provided the industry with great quantities of high-grade ores. The abundance of coking coals and limestone in the region adjoining western Pennsylvania and the development of cheap water transportation on the Great Lakes tended to shift the center of iron and steel manufacture to an area west of the Allegheny Mountains. Encouraging these new develop-

Jan 1, 1948

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

Application of technology to the search for new deposits went on apace in 1963. Traditional methods, aided by modern communications, were successful in some out-of-the way corners of the world that had not been adequately prospected, but the co-ordination of several mutually supporting techniques is necessary to define exploration targets in most areas today. Although these obviously include geophysics and geochemistry, which are treated elsewhere in this issue, geology continues to play a major role. As the search focuses on less and less obvious targets there will be more need than ever to "pull out all the stops." Any anomaly may have significance and must be evaluated as a possible lead. Ability to detect them increases as the laboratory workers refine techniques for measuring physical, chemical, and isotopic properties; it will be increasingly the responsibility of the exploration geologist to understand and apply these to economic problems. Simple propecting, the search for outcrops of recognizable ores of traditional types, was perhaps most successful for iron. Potentially large deposits of high-grade magnetite-specularite-hematite ore have been found in the Mary River area near the north end of Baffin Island. The ore holds up four hills that stand some 1500 ft above the surrounding country; obviously they were ripe for discovery by the first person to come across them, in this case Murray Watts, president of British Ungava Explorations, Ltd, As preliminary examination indicates a lump ore averaging 68 to 70% iron, these deposits may be commercial in spite of the unfavorable climate and their isolation from world markets.

Jan 2, 1964

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleys1 and Gathmann,2- who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1964

By P. A. C. Wilson

Instantaneous outbursts of carbon dioxide in coal mines have occurred in Germany only in one part of the Waldenburg-Neurode mining district.' This mining region comprises the northeastern fold of the "Innersudetian" coal basin. The basin (Fig. 1) is in the form of a geologic trough approximately 60 km. (37 miles) long and 30 to 35 km. (19 to 22 miles) broad and is enclosed on three sides by ancient truncated mountain ranges—the Riesengebirge, the Bober-Katzbachgebirge and the Eulenge-birge. Only the southeastern part of the trough is not enclosed by mountains of older rock formation. The floor of the basin before the building up of the coal measures was formed on the western, northwestern and northeastern borders by the material from Archean rocks (gneiss and mica schists); in the northern part over this was deposited the Silurian formation. The carboniferous period is represented both by the Lower ("kulm") and Upper Carboniferous, with an unconformity between the stages; that is, the kulm was tilted up and partly eroded before the Upper Carboniferous was deposited. The kulm is a salt-water formation (with marine fauna) but Upper Carboniferous rocks are nonsaline water deposits, with fresh-water flora only. The Lower Silesian coal measures were thus formed in a lime basin fed by the running water coming down from the mountains. As already indicated, the bottom series of the Upper Carboniferous formation, termed "Waldenburg strata" were laid down unconformably on the Lower Carboniferous. Over the Waldenburg strata there are the "Weisstein strata," an intermediate barren stage without coal beds, 400 to 500 m. (1300 to 1600 ft.) thick. Another unconformity followed, which is overlain by the '(Saarbrucken" series, which contain the upper coal measures, and the ('Ottweil" strata. In the last named, it is only on the southwestern fold that beds of coal are developed.

Jan 1, 1931

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan's blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations '-' of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin') apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder's Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969