Search Documents

By William Priestley

The author has shown, by .practical experiments, how the rate of cooling steel in the mold governs ingotism, segregation, the formation of dendrites, and the distribution of intergranular material; and the resulting effect these conditions have on the physical qualities of the steel before annealing, after annealing, and after forging. The paper also describes how the structure of steel is affected by the design of the mold and the method of pouring. It is shown that the various constituents of carbon steel segregate differently under different rates of cooling. For the classes of steel covered in this paper, it is concluded that the best physical structure and the most uniform chemical composition is obtained by pouring the steel at a low temperature and solidifying as rapidly as possible in the mold. MUCH time has been devoted, by metallurgists, to the study of steel after solidification and remarkable strides have been made in the heat treatment of steel, but less knowledge is available of the thermophysical, activity of the constituents of steel prior to solidification in the mold. It is known that certain elements added to steel produce marked changes in physical properties, also that other elements added to steel produce similar changes, but we have only meager knowledge as to how these elements combine in steel under different conditions of solidification. It is not sufficient to know, from chemical analysis, that a certain element is present in steel. We should know how this element is in combination with the other elements and whether the combination is such as will give the greatest physical properties. Certain elements go into solid solution with the iron, while others segregate to the grain boundaries and combine with the impurities collected there. Until it is known where an alloy produces the most beneficial effect and a means, is determined for controlling its physical location by altering solidification conditions, or otherwise, we will not obtain the maximum value from our alloys.

Jan 2, 1924

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH'S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.' The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

THE metal iron has physical arid chemical properties which are some- what different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron the former being the ordinary form at room temperature. When heated above the "A2 point," 769 C (1416 F), the metal becomes nonmagnetic, and at the "A3 point," 911 C (1672 F), it undergoes a change in crystalline form to become gamma iron. 111 the range 769 to 911 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1392 C (2538 F), it changes into delta (d) iron, which is identical with beta or nonmagnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1536 C (2797 F); the melting point is generally lowered by alloys or impurities. PHYSICAL AND THERMAL PROPERTIES OF IRON Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A3 point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly with the range of stability of a given form, but this is not always true. For ex- ample, the specific heat reaches a sharp maximum at the A2 point al- though no transformation occurs. (See Fig. 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an appreciable extent. Table 16-2 contains a list of the common elements classified with respect to their solubility in liquid iron. Those which are very soluble or practically insoluble require no further discussion, but several of the nonmetals that are gases and exhibit limited solubility are of considerable importance to us and merit more detailed consideration.

Jan 1, 1964

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

By C. Richard Tinsley

Like most minerals, coal is inherently a demand-limited commodity. The very sedimentary nature of its occurrence implies greater availability potential than demand. But this situation is overridden by economics among fuels, between coals, and within coal blends. Such considerations make coal forecasting a very hazardous profession indeed. THERMAL COAL If one thought that the lead times involved with a mining project were very long, one has obviously not been exposed to the planning process in the electric generation business - a process seriously confounded by shifts in load growth, environmental pressures, capital intensity, security of fuel sourcing, inter-fuel economics, and so on. But as a general rule, the near-term forecasts for thermal coal can reliably be based on a bottom-up, plant-by-plant analysis. Cement plant conversions can also be reasonably estimated next in order of reliability, although they have a much wider spectrum of coal qualities and fuel sources to choose from with a notably higher tolerance for sulfur and ash. Finally, industrial demand can be assembled from the estimates for conversions by pulp/paper plants, chemical plants, etc. The industrial sector is harder to estimate, since it may involve small boilers or dual-fired units. Assessing demand in the Pacific Rim is relatively a straightforward process in the near term because the major importing countries are all located on the Asian continent with either negligible or very minor (yet stable) indigenous coal production, (itself often operated on a subsidized basis). Furthermore, all imports are seaborne. These major importers are Japan, Korea, Taiwan, and Hong Kong with Thailand, Singapore, and Malaysia up-and-coming consumers. The suppliers to this market all have substantial reserves to back up decades of exports to these countries. Australia, the US, Canada, South Africa, China, and the USSR dominate the supply side. The second oil-shock of 1979/1980 has convinced the importers that reliance on oil can be expensive and eminently interruptible. Thus, they are determined to diversify away from oil' to nuclear and coal for generating electricity and for coal for other purposes where possible. This trend is seen to continue even in the face of the oil glut worldwide and oil-price reductions in early 1982. But the importers are also convinced that reliance on one coal source and, in particular, one infrastructure route for the coal chain from mine to consumer can be equally expensive and interruptible. Strikes in the US and Australia; excessive demurrage at certain ports; relegation of coal to a lower priority on multiple-use railroads in the USSR and China; and concern over escalation on high-infrastructure or high-freight coal chains are among the risks worrying the importers. As a consequence, Pacific Rim thermal coal purchases are being allocated among supplier nations, between ports, and within each country. An example of Japan's shift away from Australia and toward the US and Canada is shown in the estimates in Table 1. But the confidence of the import estimates deteriorates sharply beyond the plant conversion timetables and construction schedules in the near term. If part of the second generation of coal-fired power plants can handle lower-energy coals, the field of suppliers could widen to accept sizeable tonnages from Alaska, Wyoming, Alberta, or New Zealand resources. These supply sources generally have some infrastructure or freight advantage to compensate for their lower quality and to compete on a delivered energy-unit basis. These also offer diversification in sourcing. And the possibility of coal liquefaction in Japan further widens the sourcing network. A great number of Pacific Rim coal forecasts have been generated, especially for Japanese thermal-coal imports which are expected to grow strongly in the 1980's. Since the Japanese themselves have not yet settled their energy policy, the exact numbers are hard to call. Nevertheless, at 50 million tonnes of imports in 1990, Japan would consume 50-60% of the total Asian thermal coal imports as shown on Tables 2 and 6. The next most important consumers are the "island" nations of Korea, Taiwan, and Hong Kong (see Tables 3-5). All three are embarking on power plant developments usually with captive unloading facilities, capable of accepting more than 100,000-dwt vessels. Korea, with no-indigenous bituminous coal, is not especially enamoured with US coals, which are deemed too heavily loaded by freight and infrastructure costs -- up to 70% of the delivered price. Thermal coal contracts are presently split to Australia (70%) and to Canada (30%). Korea Electric Power Co. is already considering second-generation boilers capable of burning lower-quality coals than the present standard. Korea does burn domestic anthracite.

Jan 1, 1982

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak's4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis' solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By J. U. Messenger

A technique is described whereby the resistance of an emudian to breaking can be quantitatively determined. Produced ailfield emulsions are usually the water-in-oil type and, accordingly, do not conduct an electrical current. However, there is a threshold of A-C voltage pressure above which an emulsion will break and current will flow. The more stable an emulsion, the higher the required voltage. A Fann Emulsion Tester, modified so that low voltages (0 to 10 v) can be accurately measured, is suitable. This technique has application in evaluating the effect of a demuksifier on the stability of an emulsion. Emulsions can, in essence, be titrated with demulsifiers by adding a quuntity of demulsifier, stirring, and measuring the voltage required to cause current to flow. Any synergistic effect of two or more materials added simultaneously can be followed accurately. A demulsifier that significantly lowers the threshold voltage (from 100 to 400 v to 0 to 10 v for the emulsions in this study) is effective and can cause the enlulsion to break. A demulsifier that will bring about this drop in the threshold voltage at low concentration ir very desirable. The technique is also well adapted for rapidly screening demulsifiers. INTRODUCTION Stable emulsions in produced reservoir fluids resulting from certain well stimulation and completion procedures are common problems. The use of suitable demulsifiers can often mitigate these difficulties. At the present time, a rapid and efficient method for selecting satisfactory demulsifiers is not available. It is badly needed. Reliance is now placed primarily on trial-and-error procedures. A new test method has been developed which permits a more rapid and precise selection of demulsifiers. It involves measuring the electrical stability potential of an emulsion before and after a demulsifier has been added. This paper describes this method and shows where it should have application in field emulsion problems. NATURE OF OILFIELD EMULSIONS Two immiscible components must be present for an emuhion to form; we are concerned here with crude oil and water. An emulsifier must be present for tin emulsion to be stable. J Emulsifiers can be substances which are soluble in oil and /or mter and which lower interfacial tension. They can be colloidal solids such as bentonite, carbon, graphite, or asphalt which collect at the interface and are preferentially wet by one of these phases. Unrefined crude oils can contain both types of emulsifiers, A popular theory is that, of the two phases in an emulsion, the dispersed phase will be the one contributing most to the interfacial tension.' Usually this phase contains the least amount of emulsifier. The stability of a water-in-oil emulsion is affected by the fol1owing: l) viscosity; (2) particle or droplet size; (3) interfacial tension between the phases; (4) phase-volume ratios; and (5) the difference in density between the phases. A stable emulsion is usually characterized by high-viscosity, small droplets, low interfacial tensions, small differences in density between its phases, and slow separatian of the phases. It also has low conductivity (high electrical stability potential). Water-in-oil and oil-in-water emulsions"' are both common; however, oil field emulsions are predominantly water-in-oil emulsions. The emulsions which commonly occur during oompletion and stimulation operations contain a combination of several of the following: acids, fracturing fluids (oil, water, acid), and formation water and oil. Produced emulsions usually contain formation water and oil. Emulsions form in oil wells because oil and water are mixed together at a high rate of shear in the presence of a naturally occurring or unavoidably produced emulsifier. During the completion and stimulation of productive zones, and while formation fluids are being produced, oil and water are very often commingled. These mixtures are formed into emulsions by agitation which occurs when the fluids are pumped from the surface into the matrix of the formation or produced through the formation to the surface. Restrictions to flow (such as perforations, pumps, and chokes)".'" increase the level of agitation; tight emulsions are more likely to form under these conditions. Often an emulsified droplet is an emulsion itself.'" Therefore, emulsion-breaking problems can be quite complex. The complexity can be even greater if a third phase (gas) is included. Demulsifiers operate by tending to reverse the form of the emulsion. During this process, droplets of water become bigger, viscosity is lowered, color becomes darker, separation of the phases faster and electrical stability potential approaches zero. Any of these effects could be followed as a means of determining emulsion stability. However, electrical stability potential is the most reproducible and most easily measured parameter for following the stability of a water-in-oil emulsion.

Jan 1, 1966

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By Canada Ernst & Whinney

INTRODUCTION The principal objective of this chapter is to provide guidance in understanding and making effective use of published financial statements of mining companies. Although financial statements only represent a gathering together of information relevant to an enterprise's financial position and results of operations, they increasingly reflect the complexities of the modern day business environment. In the mining industry, a wide variety of accounting practices have evolved to deal with the unique aspects of the business in the absence of authoritative accounting pronouncements from standard-setting bodies. Given such complexities and divergent practices, financial statements of mining companies are not easily understood and cannot be used effectively as a tool in decision-making without a basic knowledge of fundamental accounting concepts, generally accepted accounting principles and their application in the mining industry. As such, this chapter is not restricted to a discussion of the accounting for the unique aspects of the mining industry. These aspects are dealt with at length but the text also includes a discussion of general accounting concepts and practices which have wide application in the mining industry. Frequent references are made in the text to international practices and to specific rules and requirements of individual countries. In this respect, the scope is restricted to four major mining environments, Canada, the UK, the US and Australia, all of which have made significant contributions to the development of generally accepted accounting principles. Acknowledgements This chapter was prepared under the direction of Ian Murray of Ernst & Whinney in Toronto, Canada. Contributions were received from Graham Butt, Mark O'Sullivan and Dominic Robinson, all from Ernst & Whinney in Toronto and Bill Duvall and Tom Schoenbaechler from Ernst & Whinney in Louisville, Kentucky, US. The authors would also like to acknowledge the assistance received from David Ferguson, Don MacLean, David Taylor and Susan Zoutman from Ernst & Whinney, Toronto, from the UK and Australian practices of Ernst & Whinney and from Ernst & Whinney International. FINANCIAL STATEMENTS - ELEMENTS AND CONCEPTS Financial statements were originally a stewardship report to owners to satisfy them that management had given a proper account of the resources with which it had been entrusted. Today, the number of users of financial statements has expanded to include the following groups: - shareholders, present and prospective; - lenders, present and prospective; - financial analysts; - regulatory authorities; - taxing authorities; - labour unions and employees; and - creditors and customers. The expectations of these user groups differ. For example, investors and lenders require information that will indicate the adequacy of their security and the profitability of the enterprise; taxing authorities will be concerned with the concept of income; labour unions and employees will focus on the profitability of the enterprise. Ground Rules for Preparing Financial Statements Responsibility for Financial Statements Financial statements are the representations of management. This may strike the reader as a rather obvious statement. It is important to remember, however, the role of judgment in accounting. Notwithstanding the promulgation of accounting standards in the developed countries, considerable flexibility remains in the selection of accounting practices and methods and in their presentation. Arguably, there is more flexibility in the mining industry as few countries have developed standards to deal with its unique aspects. Accordingly, financial statements are as much a product of management's perspective and philosophy as they are a compliance document.

Jan 1, 1985

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f'racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,' have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

.In a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. Consequently since a technical cohesion limit is defined as the technically deter-minable resistance to fracture under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. In the general investigation described in the previously-mentioned papers, 10-18,20,21,23 the influence of the stress system on the fracture stress was studied by means of tension tests of notched specimens. When a circumferentially notched cylindrical specimen is subjected to longitudinal tension, the minimum cross section is under transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S1), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (Sz = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (s3/s1) The evidence is based not only on the results of tests to fracture at various constant temperatures, but also On results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1949