Search Documents

By Alvin H. Lense

In the spring of 1967, after a careful study of existing geology along the Pacific Coast including Alaska, the USBM, in conjunction with the USGS, decided that the offshore area around Nome, Alaska, presented an unparalleled land-to-sea comparison site for the evaluation of marine core drilling techniques and sampling equipment. Considering the geological evidence available and the production history of the Nome Beaches (5-6 million oz. of gold recovered), it appeared likely that gold in commercial quantities could occur in the offshore area. A 180 sq mi area of Norton Sound, extending roughly 14 miles to the east and west of Nome and averaging 6 miles to the south, was tested by approximately 530 line-miles of sub-bottom profiling. A total of 4043 ft (56 holes) were drilled in unconsolidated sediments, yielding mixtures of gravel, sand, silt and clay. Of the total holes drilled, 16 went to bedrock and six were terminated short of their intended depths due to boulders which halted penetration, or rough seas which caused the ship to move as the anchors slipped over hard sea-floor surface. The rest of the holes were terminated when the penetrative capabilities of the drills were reached, or when the required amount of geological data were attained.

Jan 8, 1968

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and¬-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are con¬tinuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the intro¬duction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus %6-in. or plus 3-in. in the United States and plus 36-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about % in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser . sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.1,2 Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1952

By Tadeusz Cyrul

Results of a large scale compression test in situ are the subject of discussion. A cube of coal having an edge length of 1.5 meters was subjected to uniaxial compression tests in situ. At the same time both load and deformation were controlled. Deformations were measured on 60 short measurement bases, each 23 cm in length. The bases were uniformly distributed on the side surface of the cube, forming five horizontal rows and twelve columns on the development of the surface. Readings were taken from each gauge for each level of loading which was increased step by step. Due to heterogeneity of the rock, readings showed scatter. Scattered data were approximated by a plane, using the least squares method for each row separately and for the entire population of bases. Orientation of the planes are analyzed. The geometrical measure of the bending moment is introduced. It shows that the magnitude of the bending moment and the bending plane differed from row to row, thus implying that the cube was not only bent but twisted as well. This complex behaviour of the coal cube is apparently caused by its heterogeneity and vertical anisotropy. The results constitute a contribution to the verification of existing design criteria on the stability of mining pillars.

Jan 1, 1984

By A. W. Hull

The new valves described in this article are the latest product of the Research Laboratories of the General Electric Co. Some of them are still in the laboratory stage, others have already found important applications. Some of the larger ones, which have graduated from the laboratory, are waiting for their apprenticeship in industry, there to refine their frailties and complete their preparation as electrical servants. The career that awaits them, though dimly foreseen, appears fascinating. And as surely as history repeats itself, scenes still more romantic, now beyond the horizon, will unfold as we approach them. This is the romance of science. Counting Electrons Let the smallest tube lead the march of review. It is a special Pliotron, designed to measure currents smaller than any yet detected. It goes by the unromantic name of Pliotron FP-54. Fig. 1 shows this miniature tube—miniature in performance rather than size, for it is the size of an ordinary radio receiving tube. Its appearance has nothing distinctive, except the quartz beads above and below the plate, which support the grid. They minimize insulation leakage. In principle, the FP-54 is like any grid-controlled high-vacuum electron tube; but in structure and operating characteristics it is entirely special. An extra "space-charge" grid, maintained at 3 volts positive with respect to the filament, holds back the small but pernicious current of positive ions emitted by the filament; the normal plate voltage is 6 volts, grid bias 3 volts, thoriated-tungsten filament temperature 1700" K., plate current 40 microamperes. These conditions are essential to the avoidance of grid-currents, which may consist not only of insulation leakage and positive ions from the hot filament and from residual gases, but of high-speed electrons from the filament, photo emission from the grid due to the light of the filament, and electron emission caused by X-rays generated by the impact of electrons on the plate.

Jan 1, 1932

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By T. D. Yensen

AT the symposium on gases in metals held at the Annual Meeting of the Institute in New York in February, 1933, a suggestion was made1 that the term "gases in metals" as now employed is unsuitable as descriptive of the substances usually involved in that term. The Executive Committee of the Iron and Steel Division thereupon appointed a subcommittee, composed of the authors of this paper, to study the "nomenclature involved in the general subject of gases in metals, including the name itself" and to report its findings to the Executive Committee. The subcommittee decided at once to discuss the subject with an "Advisory Council" composed of representative metallurgists, metallographers and analytical and physical chemists in the Pittsburgh district.2 As a result of conferences held by the subcommittee and with the Council, a report with recommendations was submitted to the Executive Committee at an open meeting on Oct. 5, 1933, during the National Metals Congress in Detroit. The report and recommendations were accepted, and the subcommittee was instructed to proceed with the dissemination of the report for the purpose of having its recommendation generally adopted either as it was or in a modified form as a result of further discussion.

Jan 1, 1934

By Robert H. Aborn, J. J. B. Rutherford

It is now well known that troublesome intercrystalline corrosion may occur in austenitic stainless steels following exposure of the metal to a temperature within the range 1000° to 1500° F. (540° to 815° C.). The present paper describes a satisfactory method of estimating the extent of such corrosion, based on the measurement of the electrical resistance of a specimen before and after attack. This new method enabled us to study quantitatively the effect of several factors upon intergranular corrosion in the 18 Cr, 8 Ni type of alloy. The results show that susceptibility to this attack increases with increasing carbon content and grain size and appears to pass through a maximum for certain combinations of temperature of sensitization and period during which the alloy was maintained at that temperature; and are in complete accord with our interpretation of the mechanism of this phenomenon. The method is probably applicable to other metals or alloys subject to intercrystalline attack, such as the aluminum alloys of the duralumin type. The methods hitherto in use for estimating the degree of intergranular attack fall into three types: (1) microscopic examinationll (2) macroscopic examination of fractures, and (3) determination of the time required for complete failure or disintegration.2 None of these lends itself very well to a measurement of the extent of corrosion. The first two are qualitative in nature and the third provides an arbitrary value largely dependent on individual judgment, since failure is a progressive phenomenon and not a sudden event. Our experience is that weight-loss determinations, although valuable in some types of corrosion investigations, bear no simple relation to intercrystalline corrosion in this type of alloy, as is to be expected since the phenomenon probably involves only the thinnest films between adjacent metallic grains. Measurement of electrical resistance has been used recently in the study of some types of corrosion,3 but seems not to have been applied to

Jan 1, 1932

By John Birkinbine

The favor with which the members of the Institute received Mr. Fernow's paper upon the use of charbon roux in the manufacture of iron has encouraged me to present this paper, in the hope of having the discussion upon the manufacture and use of the oldest and undoubtedly the best fuel for producing pig iron continued. Owing to the advances made in employing anthracite coal, bituminous coal, or coke, or mixtures of them, we are apt to forget how much of our present development is due to the pioneers in iron manufacture and the fuel which they employed in the production of pig iron. In Mr. Swank's last compilation of the iron and steel works of the United States, the furnace capacity of the country is given as 5,868,000 tons, of which 1,000,000 tons can be made in the 264 charcoal furnaces. In other words, over one-third of the furnaces now in existence use charcoal for fuel, and produce more than onesixth of the iron made. If to this is added the 130,000 tons of blooms and billets turned out by the 122 forges and bloomaries, the importance of the charcoal industries will be appreciated.

Jan 1, 1879

By J. C. Sullivan, W. A. Knoll

THE sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In November of 1930, experimental work was con- ducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4%-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. DRILLING Air was carried down the shaft in an 8-in. flanged pipe line at a pres- sure ranging from 95 to 100 lb. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1938

By C. E. Webber

THE economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro-carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,5 who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40° to 200°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33° to 180°F. and from 100 to 5000 lb. per sq. inch.

Jan 1, 1940

By J. L. Rodda

The desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwiltl has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goereq2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for a given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest procedure. The largest particle in a given portion is then determined by Stokes' law:3

Jan 1, 1932

By Paul R. Wieber, Atam P. Sikri

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification. The potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification. Independent studies show this process to be 25% cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the most advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average production rates of 8.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds. Unique factors of the process development are discussed which may lead to commercial processes in the near term. A development strategy is proposed by which this technology could be commercialized before 1983 with potentially lower gas prices and lower environmental impacts, relative to mining plus surface gasification.

Jan 1, 1979

By Thomas W. Gibson

THE Province of Ontario in recent years has come strongly to the front as a producer of metals, especially nickel, copper, silver, and now gold. Of the last named, the output for 1922 was in the neighborhood of $20,000,000. The law governing the mining industry in a community where such develop-ments are taking place will be of interest, therefore, in other places where mining laws are up for revision The first mining of importance done in this province was for copper on the north shore of Lake Huron, where the Bruce mines were opened in 1846. These deposits of copper sulfides, notwithstanding the remoteness from markets and the cost of transportation, were vigorously worked for 12 or 15 years and also intermittently later, but the active career of the mines came to an end in 1875. From first to last, a little less than 10,000 tons of copper was produced, valued at $3,300,000. All the product was shipped to England as dressed ore, contain-ing up to 13 per cent. of the metal. In. 1866, a rich pocket of gold was found on the Richardson farm near Madoc, Hastings County, but was not followed by further discoveries of a like kind and in time the excitement it caused died away. Rich silver ore was found in 1868 on Silver Islet in Lake Superior, a speck of land not larger than a good-sized ball-room. The assemblage of minerals here was practically the same as that at Cobalt, discovered 35 years later, namely, native silver, cobalt, nickel and arsenic; in addition, there was considerable argentite, which has always been scarce at Cobalt. In all, the silver produced amounted to about $3,500,000. The belief persisted that the deposit was not mined out, and in the summer of 1922, some rich ore was extracted from the roof, perilously near the bottom of Lake Superior.

Jan 2, 1923

By Philip M. Mc Kenna

When a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be considered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essential wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered. Hardness has been the property of greatest practical interest in tool materials. The word "hardness" is a generalized term lacking definite-ness unless the specific test used is described. However, efforts to explain physical properties as a consequence of chemical bond, and distance between atoms in chemical compounds have been illuminating. This seems the most generalized attack on the problem, and is based upon the idea that atoms in a lattice are held together as the square of the valence and inversely as the square of the distance between the atoms. The compounds compared must all be of the same crystalline arrangement. 100 W2 It is interesting to note the values of the figure 7 A 3 /3for a number of

Jan 1, 1938

By Philip M. Mc Kenna

When a new material becomes available to industry, it is useful to describe its properties as a guide to its most effective application; and when the new material may be produced in compositions having a series of graded properties, tests to select the combination of properties best adapted for various uses are helpful. The class of materials to be considered in this paper are hard tool materials produced by processes of powder metallurgy from hard carbide constituents and various matrices of iron, nickel or cobalt, or alloys of them with tungsten, or tungsten and carbon. The customary use of carbide hard alloys is for metal-cutting tools; although wire-drawing dies, lathe centers, follow rests, grinding rests, burnishers, rolls, extrusion dies, measuring gauges and micrometers, and a number of other tools are also made with these hard alloys as the essential wear-resisting parts. The properties and tests to be considered are those affecting these uses. In the development of tool materials since the industrial revolution we have had carbon tool steels, Mushet steel, high-speed steels, stellites, and now cemented carbide compositions. For an understanding of the latter category of materials their properties and uses relative to the older and more familiar tool materials will be considered. Hardness has been the property of greatest practical interest in tool materials. The word "hardness" is a generalized term lacking definite-ness unless the specific test used is described. However, efforts to explain physical properties as a consequence of chemical bond, and distance between atoms in chemical compounds have been illuminating. This seems the most generalized attack on the problem, and is based upon the idea that atoms in a lattice are held together as the square of the valence and inversely as the square of the distance between the atoms. The compounds compared must all be of the same crystalline arrangement. 100 W2 It is interesting to note the values of the figure 7 A 3 /3for a number of

Jan 1, 1938

By R. D. Nelson, D. H. Polonis

ThE eutectoid decomposition of 6 phase in the Cu-Sn system (32.53 wt pct Sn) has been studied by several investigators.1-6 On the basis of X-ray work, Iball and 0wen1 reported complete decomposition of 6 in powder specimens after 7 days at 300°C. Wang and Hansen followed the micro-structural changes during heat treatment of lump specimens and estimated 5 pct decomposition after 63 days at 300°C. Wang and Hansen suggested that the discrepancy between the decomposition rates of powder and lump specimens might be due to the excess surface free energy of powders. The present work involved 6 decomposition in copper-tin alloy powders containing 32.6 wt pct Sn. Alloy lump specimens exhibited entirely 6 phase after fairly slow cooling (air cooling) from above 350°C and were so brittle that they could be easily crushed to-200 mesh in a percussion mortar. X-ray diffraction study of the as-crushed powders (-200 mesh) revealed 100 pct 6 phase with very slight line broadening effects due to strain introduced by crushing. Only 6 phase was detected by X-ray diffraction in powders which were heat treated 4 hr at 450°C and air cooled to room tem-

Jan 1, 1960

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By Michael D. Martin

Pima Mining Co., managed and 50% owned by Cyprus Mines Corp., with Union Oil of California and Utah Construction and Mining Co. sharing equally in the remaining 50%, is a medium-sized open pit copper mine situated in the very active Twin Buttes mining district, 22 miles southwest of Tucson, Ariz. In 1965, a three-part paper described Pima's growth from 3,000 tpd (tons per day) in 1957 to 18,000 tpd nine years later. Within months of the completion of the last stage of this sixfold expansion, studies were being wound up on a further major expansion, this time to 30,000 tpd. This expansion is now a reality. Details of the enlargement of the crushing and concentrating plant have already been covered in a recent paper, and the present paper will cover pit engineering studies, equipment selection, and current operating practices. Key factors in top management's decision to go ahead with the latest expansion were: (1) a substantial increase in ore reserves coupled with an appreciable decrease in grade, (2) a generally favorable outlook for copper prices, and (3) better than expected performance by mine and mill equipment purchased for the expansion to 18,000 tpd. For the pit design studies, particular attention was paid to pit stability, a problem area at times in the past, and to the location and grades of the final ramp systems. In drawing up the long-term mining schedule, the attitude of the ore, with the higher grade material lying deeper, was a critical factor and considerable stockpiling of lower-grade material in the early years had to be accepted in order to keep the annual grades close to the average of the orebody. The expansion called for major purchases of mine equipment in order to gear up the mine for delivery of 30,000 tpd to the concentrator. In general, equipment chosen was of types already proven at Pima, al- though there were some exceptions to this practice. One of these excep-

Jan 1, 1969